首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 15 毫秒
1.
Two corn hybrids (3394 and 33R87) were steeped with three sulfite salts and five acids to test the effect of sulfur dioxide (SO2) source and acid sources on wet‐milling yields and starch properties. Milling yields from each treatment were compared with a control sample that was steeped with 2,000 ppm of SO2 (using sodium metabisulfite) and 0.55% lactic acid. Sulfur dioxide sources were potassium sulfite, sodium sulfite, and ammonium sulfite; acids were acetic, hydrochloric, oxalic, phosphoric, and sulfuric. Starch yields were affected by the SO2 source and steep acids but the effects were hybrid‐dependent. Different steep acids gave different starch yields when wet milled at the same pH. Among the acids tested, weak acids (lactic and acetic) tended to give higher starch yields compared with strong acids (hydrochloric, sulfuric, phosphoric, and oxalic). Some differences were observed with different sulfite salts and acids on starch pasting properties; however, there were no clear trends.  相似文献   

2.
Effect of lactic acid, SO2, temperature, and their interactions were assessed on the dynamic steeping of a Brazilian dent corn (hybrid XL 606) to determine the ideal relationship among these variables to improve the wet‐milling process for starch and corn by‐products production. A 2×2×3 factorial experimental design was used with SO2 levels of 0.05 and 0.1% (w/v), lactic acid levels of 0 and 0.5% (v/v), and temperatures of 52, 60, and 68°C. Starch yield was used as deciding factor to choose the best treatment. Lactic acid added in the steep solution improved the starch yield by an average of 5.6 percentage points. SO2 was more available to break down the structural protein network at 0.1% than at the 0.05% level. Starch‐gluten separation was difficult at 68°C. The lactic acid and SO2 concentrations and steeping temperatures for better starch recovery were 0.5, 0.1, and 52°C, respectively. The Intermittent Milling and Dynamic Steeping (IMDS) process produced, on average, 1.4% more starch than the conventional 36‐ hr steeping process. Protein in starch, oil content in germ, and germ damage were used as quality factors. Total steep time can be reduced from 36 hr for conventional wet‐milling to 8 hr for the IMDS process.  相似文献   

3.
A procedure that reduces diffusional limitations by periodically milling the corn to reduce particle size and stirring the ground mash in the presence of sulfur dioxide (SO2) and lactic acid was developed. The process, called intermittent milling and dynamic steeping (IMDS), includes three main stages: initial soaking (a short-time immersion in water) of whole kernels, initial cracking of the partially hydrated kernels, and dynamic steeping with interspersed milling. This study evaluated the three stages of the process separately, evaluating the effect of variables on each stage of the process. Corn fractions yield (germ, fiber, gluten, starch) were used to decide the best conditions for the soaking and steeping stages, and germ damage was used to determine the best kernel cracking method. Starch, gluten, and germ yields were not affected by soak temperatures (52–68°C) or soak time (1–3 hr). A temperature of 60°C was chosen for soaking because it increased the rate of kernel hydration without gelatinizing starch, which happens at higher temperatures. A 2-hr soak time was preferred because there was less fiber in the germ fraction and less germ damage was observed. Although there were no advantage to using SO2 or lactic acid in the soak water, the presence of these compounds during dynamic steeping enhanced starch yield. The starch yield for 3 hr of dynamic steeping was not statistically different from the starch yield for a 7.5-hr dynamic steep. The Bauer mill was preferred over the use of a roller mill or a commercial grade Waring blender for kernel cracking. The IMDS process produced, on an average, 1 percentage point more starch than the conventional 36-hr steeping process. Total steep or kernel preparation time was reduced from 24–40 hr for conventional wet-milling to 5 hr for the IMDS process.  相似文献   

4.
To eliminate the diffusion barriers associated with enzyme addition during conventional steeping, we have developed a two‐stage milling procedure to evaluate the effects of enzyme addition on corn wet milling. The current study compares the effects of the addition of commercially available enzyme preparations during conventional steeping to their comparable addition in the two‐stage procedure. Results are presented in terms of yields of fiber, starch, germ, and gluten. The results demonstrate that the application of enzymes to the normal steeping step of wet milling is not an effective means of decreasing the steeping time or sulfur dioxide usage. Only when specific enzymes are added to the hydrated ground corn, using the modified two‐stage procedure, are enzymes effective in decreasing the steeping time and sulfur dioxide requirements. The overall steeping time with the two‐stage modified procedure ranges from 6 to 8 hr, representing a 67–83% reduction over the conventional process. The modified process greatly decreases, and possibly eliminates, the need for sulfur dioxide addition, while producing starch yields and quality equivalent to that from the conventional process.  相似文献   

5.
To better understand the role of lactic acid (LA) in corn wet‐milling, steeping studies were performed on different yellow dent corn hybrids using four different solutions containing LA, sulfur dioxide (SO2), a combination of LA and SO2, or no added chemicals. Although there was variation in protein solubilization among the hybrids, protein release was consistently higher when LA was included in the steepwater than when it was excluded (both with and without SO2). Several groups have reported that starch recoveries are improved when steepwater contains LA. To explore the relationship between protein solubilization and starch yield as effected by LA, several yellow dent hybrids were steeped in 0.20% SO2 and 0.50% LA‐0.20% SO2 solutions and milled to recover starch by a 100‐g laboratory corn wet‐milling procedure. In all instances, both starch yields and protein solubilization were enhanced in solutions containing LA. These results support the hypothesis that direct dissolution of the endosperm protein matrix by LA contributes to the improved starch recoveries.  相似文献   

6.
The effect of adding lactic acid and sulfur dioxide at different times from the start of batch steeping on corn starch yields was studied. Five commercial hybrids were steeped with 0.5% lactic acid or 0.2% sulfur dioxide added over the first 15 hr of steeping and wet-milled following a 100-g corn wet-milling procedure. No significant differences were observed in starch yields when lactic acid was added to the steep solution (SO2 and water) from 0 hr (start of steeping) to 15 hr. Addition of SO2 to the steep solution (lactic acid and water) resulted in significantly higher average starch yields when SO2 was added between 5 and 15 hr compared with addition at 0 hr (SO2 and lactic acid for full 24 hr of steeping). Based on the results of the first experiment, a second experiment was done in which one of five original hybrids was steeped for 24 hr, during which lactic acid or SO2 was added until 23.9 hr (i.e., 5 min before milling) after the start of steeping. Similar results were found in the second experiment. Residual protein in starch samples did not exceed 0.85%. Steepwater protein content decreased with delays (16–20 hr) in adding either chemical to the steep solution. A significant effect on starch pasting properties of chemicals and duration of chemicals in steep-water was observed. Testing these findings using a larger scale (1,000 g) corn wet-milling procedure produced results similar to those obtained with the 100-g corn wet-milling procedure.  相似文献   

7.
The present research evaluated the feasibility of using ozone (O3) to replace sulfur dioxide (SO2) in corn steeping. Traditionally, steep water contains 0.1–0.2% sulfur dioxide to promote starch‐protein separation and high starch yields, and to control microbial growth. However, residual SO2 in starch products affects product quality and jeopardizes the “organic products” claims. Also, SO2 discharged to the environment pollutes water and air. Ozone is a strong oxidant and disinfectant with a capability to control the growth of putrefactive microorganisms in steeping systems, and to break down the endosperm protein matrix and, hence, improve starch release. This study demonstrates that an ozone‐aided steeping (OAS) process had starch yields as high as conventional SO2 steeping. OAS processes can be conducted at a lower temperature (20°C vs. 50°C) and for shorter times (36 hr vs. 48 hr) than the conventional SO2 processes, suggesting significant energy savings and increased productivity. We have found that the timing of ozone application is of great importance to the performance of the OAS process.  相似文献   

8.
The effects of alternative corn wet‐milling (intermittent milling and dynamic steeping (IMDS), gaseous SO2 and alkali wet‐milling) and dry grind ethanol (quick germ and quick fiber with chemicals) production technologies were evaluated on the yield and phytosterol composition (ferulate phytosterol esters, free phytosterols, and fatty acyl phytosterol esters) of corn germ and fiber oil and compared with the conventional wet‐milling process. Small but statistically significant effects were observed on the yield and composition of corn germ and fiber oil with these alternative milling technologies. The results showed that the germ and fiber fractions from two of the alternative wet‐milling technologies (the gaseous SO2 and the IMDS) had, for almost all of the individual phytosterol compounds, either comparable or signficantly higher yields compared with the conventional wet‐milling process. Also, both of the modified dry grind ethanol processes (the quick germ and quick fiber) with chemicals (SO2 and lactic acid) can be used as a new source of corn germ and fiber and can produce oils with high yields of phytosterols. The alkali wet‐milling process showed significantly lower yields of phytosterols compounds in germ but showed significantly higher yield of free phytosterols, fatty acyl phytosterol esters and total phytosterols in the fiber fraction.  相似文献   

9.
Reducing corn steep time by adding lactic acid instead of relying on in situ fermentation was studied. Corn at two initial moisture levels (15 and 20%) was steeped for 18 hr in a countercurrent steep system. The initial SO2 target concentration in steepwater was 2,000 or 3,000 ppm, while the initial lactic acid concentration in steepwater was 0, 0.28, or 0.55%. Adding lactic acid under all steeping conditions decreased steepwater pH, accelerated SO2 absorption, and increased the amount of solids released from corn. Adding lactic acid during steeping also increased the first grind slurry density and made germ skimming easier than when no lactic acid was added. Starch yields for the hybrid used in this study under all steep conditions were comparable to those from 24‐hr steeping, except when steeping corn with an initial moisture content of 15% in ≈2,000 ppm of SO2 alone. For the 20% moisture corn, adding lactic acid to fresh steepwater significantly improved the starch yield at ≈2,000 ppm of SO2 for 18‐hr steeping. At ≈3,000 ppm of SO2, adding lactic acid did not increase the starch yield for the hybrid used. The protein content in starch was significantly lower when lactic acid was added. Pasting properties of starch were not affected by adding lactic acid. The hybrid used in this study had an initial moisture content of 20% and could be wet‐milled without affecting starch yield, starch protein content, and pasting properties.  相似文献   

10.
Several coproducts result from fractionating corn in the wet‐milling process. Because small changes in product composition and milling characteristics can have a major impact on coproduct yields and values, testing is done to anticipate final product yields. Using small sample size and controlled conditions, a laboratory wet‐milling method proved to be a useful tool for wet milling and genetics industries. A wet‐milling process (100‐g batches) was used for data collection. Data collected during 11 years (1994–2004) were observed for samples used as benchmarks to verify process precision and accuracy and determine correlations among wet‐milling yields. More than 400 milling tests were performed on benchmark samples. Data from benchmark samples also were pooled. Coefficients of variation were low (<6%) for mean yields; year‐to‐year standard deviations of benchmark sample yield means were homogenous and implied precision of the procedure. Some differences were detected in mean yields among years (P ≤ 0.05) for benchmark data due to combined effects of hybrid and environment. A negative correlation (r = –0.58) was observed between starch and gluten yield for pooled benchmark data. Four years (2002–2005) of milling data from commercially available hybrids were analyzed using the milling procedure. For pooled commercial data, the correlation between starch and fiber yield was (r = –0.80); correlation between starch and gluten was (r = –0.76).  相似文献   

11.
The conventional corn wet‐milling process requires a long steeping time and has environmental and health concerns from the use of SO2. A recently proposed two‐stage enzymatic milling procedure with the first stage of water soaking and coarse grinding of corn and the second stage of incubating with enzymes has been shown to reduce the soaking time and possibly eliminate the need for SO2 addition. This current work explored the applications of protease and high‐intensity ultrasound in the second stage of the two‐stage enzymatic milling for corn starch isolation to further shorten the process time without use SO2. of The starch yield from sonication alone was 55.2–67.8% (starch db) as compared with 53.4% of the water‐only control with stirring for 1 hr and 71.1% of the conventional control with SO2 and lactic acid steeping for 48 hr. Protease digestion alone for 2 hr was not effective (45.8–63.9% yield) in isolating corn starch, but the starch recovery was increased to 61.2–76.1% when protease was combined with sonication. The preferred combination was neutral protease digestion for 2 hr followed by sonication at 75% amplitude for 30 min. The results demonstrated that combinations of high‐intensity ultrasound and neutral protease could replace SO2 and shorten the steeping time in the enzymatic wet‐milling process for corn starch isolation.  相似文献   

12.
Enzymatic milling is a modified wet‐milling process that uses proteases to significantly reduce the total processing time during corn wet milling and eliminates the need for sulfur dioxide as a processing agent. To optimize the overall enzymatic milling procedure and minimize the amount of enzyme, a series of experiments were done to determine the best first grind parameters and the optimal enzyme additions. The yields for germ, germ quality, and starch recovery were used for evaluation of first grind and enzyme addition, respectively. The specific processing conditions evaluated were the soaking time and first grind parameters. After soaking and first grind optimization, enzyme concentration and pH determinations were evaluated using bromelain as an example. The first grind procedure was optimized by evaluating a combination of different soaking and grinding conditions followed by a fixed enzyme addition and incubation step. The pH profile of bromelain for enzymatic milling was evaluated for pH 3.5–6.5 and the optimum was determined to be pH 5.0. Enzyme addition was then evaluated using the optimized first grind conditions and bromelain additions with 0–1.9 g of enzyme (based on protein)/kg of corn. Results showed that the minimum addition of bromelain to reach starch yields equivalent to conventional yields were ≈0.4 g of protein/kg of corn. This amount is significantly less than what was previously used and reported.  相似文献   

13.
The effect of a commercial cell‐wall‐degrading enzyme (CWDE) complex on the steeping time and starch yields of white regular sorghum (RSOR) compared with yellow maize (YMZ) was determined. An in vitro wet‐milling method standardized to test dosages of 0–120 fungal β‐glucanase units (FBG)/100 mL indicated that starch yields were significantly higher for YMZ than RSOR and increased proportionally as enzyme dosage increased. A factorial experiment with a level of confidence of P < 0.05 was performed to study the effect of CWDE addition to coarsely ground grains for 4 hr after 20 or 44 hr of SO2 steeping of whole grains. At both regular steep times, YMZ yielded significantly higher amounts of starch than RSOR. When steep times were compared, grains soaked for 48 hr produced 1.7% higher starch yields than counterparts treated for 24 hr. CWDE significantly increased starch yields and recoveries. Enzyme‐treated grains yielded 2.5% more starch than counterparts steeped regularly. For both grains, the best wet‐milling conditions to obtain the highest amount of starch were 48 hr of steeping and CWDE addition. Under these conditions, YMZ and RSOR yielded 66.9 and 66.6% starch, respectively. Starches obtained after the enzyme treatment at both steep times contained higher amounts of residual protein and ash compared with the untreated counterparts. Rapid viscoamylograph properties of YMZ and RSOR starches were not affected by the use of the CWDE nor the steep time. In comparison with RSOR starch, the YMZ starch initiated gelatinization at lower temperature, had less shear thinning and higher viscosity or setback at the end of cooling.  相似文献   

14.
The use of corn (Zea mays L.) hybrids with high grain yield and starch extractability has steadily increased in the processing industry. In light of widespread corn seed industry participation in the Germplasm Enhancement of Maize Project (GEM), which seeks to enhance exotic germplasm, future hybrids may contain more exotic sources in genetic backgrounds. It is necessary to establish and monitor physical, compositional, and milling characteristics of the new exotic breeding materials to determine the processing value. The present study was conducted to determine the wet‐milling characteristics of a set of GEM lines compared with typical Corn Belt lines. Ten GEM lines introgressed with exotic materials from Argentina, Chile, Cuba, Florida, and Uruguay and previously identified as having different starch yields, three commercial inbred lines, and two public inbred lines (B73 and Mo17) were analyzed using both near‐infrared transmittance (NIT) and a 100‐g wet‐milling procedure. There were statistical differences (P < 0.05) in the yield of wet‐milled fractions (starch, fiber, gluten, and germ). The GEM lines AR16035:S19‐227‐1‐B and CUBA117:S1520‐562‐1‐B had similar or better starch yield and starch recovery than B73 and the other adapted inbred lines, indicating that they may be useful in improving the proportion of extractable starch present in kernels of hybrids. Residual protein levels in the starch and gluten fractions were 0.26–0.32% and 38–45%, respectively. The starch yield of GEM lines from wet milling correlated positively with starch content from NIT and was negatively correlated with protein content of the corn kernels. Oil content in the germ varied from 50 to 60%. Our results indicate that incorporating GEM lines in a breeding program can maintain or even improve wet‐milling characteristics of Corn Belt materials if lines with appropriate traits are used.  相似文献   

15.
Pioneer 8500, a red hard sorghum hybrid, was steeped batchwise using three steeping solutions at 50°C: SO2 solution; SO2 solution containing 1.25% (w/w) of a commercial multiple‐enzyme preparation (Novo SP249); and SO2 solution with the addition of 0.5% (w/w) lactic acid. Novo SP249 contained pectolytic, cellulolytic, hemicellulolytic, and proteolytic activities and small amounts of saccharolytic activities. Three SO2 concentrations (0.1, 0.2, and 0.3% w/v) prepared by dissolving sodium bisulfite in distilled water and three steeping times (24, 36, and 48 hr) were used. Incorporation of multiple enzymes into the SO2 resulted in an increase in starch yield with reduced protein content compared with the SO2 solution alone. The best wet‐milling performance for sorghum resulted from the SO2 solution containing 0.5% lactic acid; it produced the whitest starch with the highest yield and the lowest protein content. Both higher SO2 concentration of the steeping solution and longer steeping time led to higher starch yield, lower protein content in starch, and whiter starch. However, no significant differences in starch yield, protein content in starch, and starch color occurred between SO2 concentrations of 0.2 and 0.3% for all three steeping solutions. The optimum steeping process for wet milling of sorghum was using a 0.2% SO2 solution with 0.5% lactic acid for 36 hr at 50°C. Under these conditions, the starch yield, protein content in starch, and L value of starch color were 60.2% (db), 0.49% (db), and 92.7, respectively, which were not significantly different from the best values from the 48‐hr steeping using the solution with 0.3% SO2 and 0.5% lactic acid.  相似文献   

16.
Recently, we reported the development of an enzymatic corn wet‐milling process that reduces or eliminates sulfur dioxide requirements during steeping, considerably reduces steep time, and produces starch yields comparable to that of conventional corn wet‐milling. The best results so far, using the enzymatic corn wet‐milling procedure, were achieved when a particular protease enzyme (bromelain) was used. In this study, pasting properties and surface characteristics of starch obtained from six different enzyme treatments (three glycosidases [β‐glucanase, cellulase, and xylanase] and three proteases [pepsin, acid protease, and bromelain]) using the enzymatic corn wet‐milling procedure were evaluated and compared with those from starch obtained using the conventional corn wet‐milling procedure. Significant effects from enzymatic milling were observed on all the three starch pasting properties (peak, shear thinning, and setback). The setback viscosities of starch from all enzyme treatments were significantly lower compared with those of the control sample, indicating that starch polymers from enzymatic corn wet‐milling do not reassociate to the same extent as with the control. Comparison between bromelain treatment and the control sample showed that starch samples obtained from bromelain treatment are very similar to control starch in water‐binding capacity, molecular breakdown, and time to swell when cooked in water. Significant effects from enzymatic milling were observed on the surface characteristics of starch granules. The glycosidase treatments, especially the β‐glucanase samples, showed holes in the starch granules. No visual differences were observed in starch granules between bromelain and control samples.  相似文献   

17.
A small‐scale (100 g of grain) procedure was developed to wet‐mill grain sorghum into six fractions by modifying the procedure of Eckhoff et al (1996). The wet‐milling process was repeated five times on commercial grain sorghum, and the mean yield (69.4%) of starch (≤0.3% protein) varied by 0.3%, whereas the yields of fiber, gluten, and germ plus bran fractions varied by 5–6%. The starch fraction accounted for ≈95% of that in the grain, while the total solids recovered was 99.0%. Four other samples of grain sorghum gave 92–95% recoveries of starches and 98.2–99.8% recoveries of total solids. All grain sorghum starches had lightness (L*) values and pasting curves nearly equal to those of a commercial maize starch.  相似文献   

18.
Physicochemical properties of maize starch obtained under different steeping conditions by intermittent milling and dynamic steeping process (IMDS) were studied. Brazilian dent maize (hybrid XL 606) was milled using a 2×2×3 factorial experimental design with two lactic acid levels (0.0 and 0.55%, v/v), two SO2 levels (0.05 and 0.1%, w/v), and three temperatures (52, 60, and 68°C). Properties of starch obtained by conventional wet‐milling process (36 hr at 52°C, 0.55% lactic acid, and 0.2% SO2) were used for comparison. Starch protein content and solubility increased with presence of lactic acid, while swelling power decreased. Higher SO2 concentration (0.1%) had the same effect as lactic acid on some properties. Steeping temperatures of 60 and 68°C increased solubility and most of the thermal properties but reduced swelling power, suggesting stronger starch annealing during IMDS at these temperatures. Some thermal changes on starch granules were visualized by scanning electron microscopy (SEM) at 60 and 68°C. Amylose content as well as pasting properties were affected by steeping factors and interactions. Starches from IMDS and conventional wet‐milling processes were similar in most properties, indicating that IMDS provides starch with quality similar to that from conventional milling.  相似文献   

19.
Abstract

Soils have substantial capacity for sorption of sulfur dioxide (SO2) but little is known about the nature of the sorbed S. Three surface soils varying in pH, organic matter, CaCO3 equivalent and surface area were exposed to air containing 5% SO2 and subsequently analyzed by ten different procedures to characterize the sorbed S. Most of the sulfur retained by soils after exposure to SO2 could be recovered as CaCl2‐extractable S, Ca(H2PO4)2‐extractable S, or S released as H2S by hydriodic acid (HI). Only small amounts of sulfur could be recovered as tetrachloromercurate (TCM)‐extractable S, S released as SO2 by HCl, or S released as H2S by HCl + Zn, HCl + Sn, or Raney Ni and NaOH. However, large amounts of S released as SO2 by HCl were recovered from the air‐dry Webster and the moist Storden soils indicating that SO2 sorption is influenced by organic matter in air‐dry soils and by CaCO3 in moist soils.  相似文献   

20.
The effects of harvest moistures and frozen storage times on corn wet‐milling yields and the pasting properties of the resulting starch were studied. Pioneer hybrid P‐0916‐XR harvested at three moisture contents (49, 35, and 21% wb) were stored frozen for three days or for five months, followed by wet‐milling. The pasting properties of the resulting starch were evaluated with a Rapid Visco Analyzer. The yields of starch and germ increased by 1.2 and 1.9 percentage points, respectively, when harvest moisture decreased from 49 to 21% wb, whereas the yields of steep water solids, total fiber, and gluten decreased by 2.1, 0.7, and 0.6 percentage points, respectively. The frozen corn had lower coarse fiber yields but higher cellular fiber yields. The starch pasting properties showed that peak and breakdown viscosities decreased by 8% (3,824 ± 36 versus 3,520 ± 38 cP) and 13% (2,336 ± 47 versus 2,029 ± 60 cP), respectively, when harvest moisture decreased from 49 to 21% wb, whereas peak time increased by 5% (6.32 ± 0.06 versus 6.62 ± 0.07 min). The setback and final viscosities of starch from long‐term frozen storage (five months) were 14% (1,574 ± 65 versus 1,828 ± 79 cP) and 8% (3,063 ± 27 versus 3,317 ± 101 cP) lower, respectively, than that from control (unfrozen) corn.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号