首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 31 毫秒
1.
A surfactant is used to enhance spinnability of carbon nanotube (CNT) fibers during direct spinning via chemical vapor deposition (CVD). In this study, the non-ionic surfactant, polysorbate, is used due to its good solubility in the CNT synthesis solution. The addition of the surfactant increased the specific strength and electrical conductivity of CNT fibers. Due to these enhanced properties, CNT fibers can be spun at higher speeds which results in lower linear density. These enhancements are due to the reduced agglomeration of iron catalysts during the synthesis of CNT fibers via CVD. This simple approach may create new applications for CNT fibers, such as for artificial muscles and power cables.  相似文献   

2.
Fiber-reinforced plastic (FRP) is composed of reinforced fibers and matrix resin, and has high specific strength and low-density materials. Because of the orientation of the fibers within them, FRPs are prone to buckling damage when under compression along the axial direction of the fiber, especially flexible organic ones. The compressive performance of FRP is largely dependent on fiber properties. the buckling load of FRP will increase with the increasing of fiber’s. In this study, we developed a way to improve the compressive and bending strength of ultra-high molecular weight polyethylene (UHMWPE) fibers. Carbon nanotubes (CNTs) and vapor-grown carbon fibers (VGCFs) were coated on the surface of UHMWPE fibers by pyrrole vapor deposition. The transverse compressive strength and bending strength of single UHMWPE fibers were determined by microcompression and single fiber bending measurements, respectively. The experiment result showed that coating UHMWPE fibers with CNTs and VGCFs increased both their transverse compressive strength and bending strength. It is excepted that the improved fiber would applied in FRP for better compressive performance.  相似文献   

3.
In this study, we report the fabrication and evaluation of a hybrid multi-scale basalt fiber/epoxy composite laminate reinforced with layers of electrospun carbon nanotube/polyurethane (CNT/PU) nanofibers. Electrospun polyurethane mats containing 1, 3 and 5 wt% carbon nanotubes (CNTs) were interleaved between layers of basalt fibers laminated with epoxy through vacuum-assisted resin transfer molding (VARTM) process. The strength and stiffness of composites for each configuration were tested by tensile and flexural tests, and SEM analysis was conducted to observe the morphology of the composites. The results showed increase in tensile strength (4–13 %) and tensile modulus (6–20 %), and also increase in flexural strength (6.5–17.3 %) and stiffness of the hybrid composites with the increase of CNT content in PU nanofibers. The use of surfactant to disperse CNTs in the electrospun PU reinforcement resulted to the highest increase in both tensile and flexural properties, which is attributed to the homogeneous dispersion of CNTs in the PU nanofibers and the high surface area of the nanofibers themselves. Here, the use of multi-scale reinforcement fillers with good and homogeneous dispersion for epoxy-based laminates showed increased mechanical performance of the hybrid composite laminates.  相似文献   

4.
In this research, results of an experimental and artificial neural network fuzzy interface system (ANFIS) modeling of operating parameters on tensile strength of the carbon fibers are investigated. To do these experiments, the commercial polyacrylonitrile (PAN) fiber of Polyacryl Iran Corporation (PIC) was used as the precursors. The results show that increasing all of parameters improves tensile strength performance. ANFIS was applied to predict tensile strength of carbon fibers as a function of stabilization temperature at first stage (STFIS), stabilization temperature at second stage (STSS), stabilization temperature at third stage (STTS), stabilization temperature at fourth stage (STFOS), and carbonization temperature (CT). The optimum levels of influential factors, determined for tensile strength are STFIS 200 °C, STSS 225 °C, STTS 240 °C, STFOS 260 °C, CT, and 1400 °C. The modeling results showed that there is an excellent agreement between the experimental data and the predicted values. Furthermore, the fiber process is optimized applying differential evolution (DE) algorithm as an effective and robust optimization method.  相似文献   

5.
Mechanical properties of chopped carbon fiber (CF) reinforced PC/ABS composites were investigated. Tensile strength and elastic modulus of the composites were enhanced with increasing CF contents. On the contrary, impact strength of the composite was decreased with increasing CF fraction. Film insert molding was introduced in order to improve impact strength. Film insert molded composite specimens have higher impact strength than conventional injection molded composite specimens because inserted film acted as a cushion to absorb the impact energy. Large warpage which was observed after molding and known as a disadvantage of the film insert molded part can be prevented by controlling the amount of filled CFs. Therefore, fiber reinforcement and film insert molding can be applied simultaneously to reduce warpage of the film insert molded part and enhance impact strength of the CF reinforced composite.  相似文献   

6.
A study on the tensile and flexural properties of jute-glass-carbon fibers reinforced epoxy hybrid composites in inter-ply configuration is presented in this paper. Test specimens were manufactured by hand lay-up process and their tensile and flexural properties were obtained. The effects of the hybridization, different fibers content and plies stacking sequence on the mechanical properties of the tested hybrid composites were investigated. Two-parameter Weibull distribution function was used to statistically analyze the experimental results. The failure probability graphs for the tested composites were drawn. These graphs are important tools for helping the designers to understand and choose the suitable material for the required design and development. Results showed that the hybridization process can potentially improve the tensile and flexural properties of jute reinforced composite. The flexural strength decreases when partial laminas from a carbon/epoxy laminate are replaced by glass/epoxy or jute/epoxy laminas. Also, it is realized that incorporating high strength fibers to the outer layers of the composite leads to higher flexural resistance, whilst the order of the layers doesn’t affect the tensile properties.  相似文献   

7.
In order to develop composites with better mechanical properties and environmental performance, it becomes necessary to increase the hydrophobicity of the natural fibers and to improve the interface between matrix and natural fibers. Graft copolymerization of natural fibers is one of the best methods to attain these improvements. Only few workers have reported the use of graft copolymers as reinforcing material in the preparation of composites. So in the present paper, we report the preparation of graft copolymers of flax fibers with methyl acrylate (MA) using Fenton’s reagent (FAS-H2O2) as redox system. Synthesized flax-g-poly(MA) was characterized with FTIR, TGA/DTA, scanning electron microscopy (SEM), and X-ray diffraction (XRD) techniques. Composites were prepared using flax-g-poly(MA) as a reinforcement and phenolformaldehyde (PF) as the binding material. Mechanical properties of phenol-formaldehyde composites were compared and it has been found that composites reinforced with flax-g-poly(MA) showed improvement in mechanical properties. Composites reinforced with flax-g-poly(MA) showed better tensile strength (235 N) and compressive strength (814 N) in comparison to composites reinforced with original flax fiber which showed lesser tensile strength (162 N) and compressive strength (372 N). Composites reinforced with flax-g-poly(MA) shows the improved MOR, MOE, and SP.  相似文献   

8.
Ni-coated short carbon fibers (Ni-SCFs) were prepared using an electrodeposition method. Short carbon fiber (SCF) reinforced epoxy composites were prepared by changing the fiber content (0.1–0.7 wt%). To investigate the effect of Ni-coated short carbon fibers on the mechanical and electrical properties of the composites, we prepared two kinds of reinforcements: the short carbon fibers treated by 400 °C (400 °C treated SCFs) and Ni-SCFs. Fracture characteristics of the composites revealed the Ni coatings and the epoxy matrix had a better interface, so that the results of tensile and bending strength were better in epoxy/Ni-SCFs composites than those in epoxy/400 °C treated SCFs composites. The 400 °C treated SCFs decreased the electrical resistivity of the epoxy composites, compared to the pure epoxy. However the epoxy/Ni-SCFs composites had lower electrical resistivity than epoxy/400 °C treated SCFs with the same fiber content.  相似文献   

9.
Intra-layer and inter-layer hybrid composite laminates were made with epoxy resin and compositions were varied in six different proportions. In-plane compressive mechanical properties were studied using finite element analysis and experiments, and the results found were in good agreement. Properties of intra-layer and inter-layer hybrids were compared with plain carbon/epoxy and plain glass/epoxy composites, and a comparison among themselves was also made. It was found that intra-layer hybrids to some extent exhibit better compressive properties compared to inter-layer hybrids. Percentage enhancement in compressive failure strain was noticed. Negative hybrid effects on compressive strength was noticed for both intra-layer and inter-layer hybrid configurations. It was found that proportion of carbon fiber content plays a key role in determining the compressive properties. According to macro-scale observation all composite laminates failed catastrophically under compressive loading. SEM observation depicted that under compressive loading carbon fibers break first followed by glass fiber.  相似文献   

10.
Multi-functional comonomer from pentaerythritol (PE) and terephthaloyl chloride (TPC) was synthesized and used for polymerization of poly(p-phenylene benzobisoxazole) (PBO) copolymer. PBO copolymer fibers were prepared from PBO copolymers using a dry-jet wet spinning. The tensile strength of PBO copolymer fibers was higher than that of PBO, and showed 42 % increase at 0.5 mol% loading of comonomer. The tensile modulus of PBO copolymer fiber at 0.5 mol% loading showed 192 % increase compared to PBO fiber. The compressive strength of PBO copolymer fiber had values between 0.46 GPa and 0.6 GPa with the comonomer content. 64-114 % increase in compressive strength of PBO copolymer fibers was observed compared to PBO fiber.  相似文献   

11.
The fiber-reinforced syntactic foam is a type of lightweight materials. In this paper, hollow glass microspheres/epoxy syntactic foams reinforced by carbon fibers are prepared. Carbon fibers of five mass fractions are used to obtain five types of reinforced syntactic foams. The effect of the fiber content and soaking corrosion on the flexural properties of syntactic foams are investigated. The results of soaking test show that the moisture rate in distilled water is greater than that in seawater. The flexural test results show that the flexural strength of syntactic foams increases obviously by adding fibers. The maximum value increases 25.5 % than that of composites without adding fibers when fiber-mass fraction is 5 %. Soaking corrosion reduces the flexural properties of the syntactic foams. The flexural strengths of syntactic foams immersed in water and seawater with 5 % fiber-mass fraction decrease 34.4 % and 37.5 % respectively. The main reasons of the flexural strength reduction of syntactic foams with soaking corrosion are discussed.  相似文献   

12.
A method for manufacturing sheath-core structured fibers was developed using wet spinning techniques. The core portion of a fiber was prepared using a carbon nanotube (CNT) solution while the sheath used a fiber-forming polymer such as polyvinyl alcohol (PVA). Preparation methods of CNT solutions were investigated and it was found that dispersivity and concentration played an important role in the formation and spinning of fiber??s core. CNT solution prepared using a surfactant with high molecular weight such as sodium lignosulfonate (SLS) was most effective and the CNT concentration was as high as 30 g/l. Fiber processing conditions were optimized and it was determined that stretching fibers in the coagulation bath was a significant step in the formation of a solid and well structured core. Drawn fibers were so strong and flexible that they could be woven into a fabric for potential use as a pressure sensor. These results are relevant for practical applications, such as the development of large-area fabric sensors. Furthermore, the described procedure to produce sheath-core CNT fibers is scalable as wet spinning methods have been widely used in the fiber industry.  相似文献   

13.
We report a phenomenal increase in strength, modulus, and fracture strain of ultra high molecular weight polyethylene (UHMWPE) fiber by 103 %, 219 %, and 108 %, respectively through hybridizing this fiber with Nylon 6 as a minor phase and simultaneously reinforcing it with single-walled carbon nanotubes (SWCNTs). Loading of Nylon 6 and SWCNTs into UHMWPE was 20.0 wt% and 2.0 wt%, respectively. Hybridized fibers were processed using a solution spinning method coupled with melt mixing and extrusion. We claim that the enhancement in strain-to-failure of the nanocomposites is due to induced plasticity in the hybridized Nylon 6-UHMWPE polymers. The enhancement in strength and stiffness in the nanocomposites is attributed to the load sharing of the SWCNTs during deformation. Differential scanning calorimetry (DSC), X-ray diffraction (XRD), scanning electron microscopy (SEM) and Fourier transform infrared spectroscopy (FTIR) studies showed that changes in percent crystallinity, rate of crystallization, crystallite size, alignment of nanotubes, sliding of polymer interfaces and strong adhesion of CNT/polymer blends were responsible for such enhancements.  相似文献   

14.
Most materials used in daily life are polymeric materials based on petrochemistry. The used polymeric materials can cause land pollution and air pollution after landfill or incineration. In contrast, natural fiber reinforced (NFR) composites are more suitable for the environment, however the reliability in terms of the durability and weatherability of NFR composites is still lacking. Thus, NFR composites require the reliability involved with durability and weatherability. In this work, poly(butylene terephthalate-co-glutarate) (PBTG), with a chemical structure similar to biodegradable PBAT, was used as the matrix in the composites, and hemp fibers were used as the reinforcement. Hemp/PBTG composites were fabricated by stacking hemp-fiberwebs and PBTG films with various fiber contents and thermal exposure times. Characteristics of the composites, such as the morphological structure, chemical structure, tensile properties, compressive properties, flexural properties, and impact strength, were analyzed to obtain the effects of fiber volume fraction and thermal exposure. As a result, hemp/PBTG composites were hardened in proportion to fiber volume fractions, and the hardening behavior of the composites increased tensile strength and flexural strength. However, the hardened structure of the composites decreased the impact strength and compressive strength of the composites. On the other hand, the mechanical properties of hemp/PBTG composites with thermal exposure times, were governed significantly by the brittleness behavior of the resin and the increased crystallinity of hemp fibers. Thus, the hemp fibers contributed to the improvements on structural stability, tensile strength and flexural strength of the hemp/PBTG composites, and increased the thermal durability of the composites with various thermal exposures.  相似文献   

15.
The tribological performance of PA6 and carbon fiber reinforced polyamide 6 (CF/PA6) under dry sliding condition was examined. Different contents of carbon fibers were employed as reinforcement. All filled and unfilled polyamide 6 composites were tested against CGr15 ball and representative testing was performed. The effects of carbon fiber content on tribological properties of the composites were investigated. The worn surface morphologies of neat PA6 and its composites were examined by scanning electron microscopy (SEM) and the wear mechanisms were discussed. Moreover, all filled polyamide 6 have superior tribological characteristics to unfilled polyamides 6. The optimum wear reduction was obtained when the content of carbon fiber is 20 vol%.  相似文献   

16.
Carbon fibers and precursor polyacrylonitrile (PAN) fibres that contain either silica or hydroxyapatite particles, imbedded during the spinning process, were studied in this paper. The modified PAN fibers were thermally stabilized using a multi-stage process in the temperature range between 150 to 280 °C in an oxidative environment. Subsequent carbonization leading to obtain carbon fibers was carried on at 1000 °C in an argon atmosphere. The changes of properties of composite precursor fibers taking place during stabilization and carbonization processes were investigated by the combination of Differential Scanning Calorimetry, Fourier Transform Infrared Spectroscopy, Scanning Electron Microscopy equipped with energy dispersive X-ray spectrometer and ultrasonic methods. Mechanical properties, such as tensile strength, static Young’s modulus, elongation at fracture were analyzed at each stage of thermal stabilization process. Additionally some traditional measurements like fiber diameter and mass were studied. Ceramic powders added to the spinning solution were present also in composites fibers after stabilization and carbonization process. Such modification allows to avoid the post-treatment operations, for example by coating or covering with films, which were usually necessary in order to obtain bioactive character of implants. Modification of carbon fibers using calcium phosphate or silica can lead to the development of a new materials for the manufacturing of implants which can establish direct chemical bonds with bone tissue after implantation.  相似文献   

17.
A commercially available polyester resin was reinforced with cabuya fibers. The experimental variables were the fiber loading and the length of the fiber. Tensile strength, flexural strength, and the Izod impact resistance were measured for the samples and compared to the polyester resin performance without reinforcement. Mechanical properties of the cabuya fiber reinforced material were also compared with the same resin but reinforced with glass fibers. An increase in fiber load decreases the tensile strength for the cabuya reinforced composite, where a value of 52.6 MPa corresponded to the tensile stress of the resin without reinforcement and a value of 34.5 MPa for the best reinforcement achieved with cabuya. An increase in both fiber load and length increases the Young’s modulus of the cabuya reinforced material, and a maximum value of 2885 MPa was obtained. The Young’s modulus and impact resistance values for the cabuya composite (2885 MPa and 100.87 J/m, respectively) reached higher values than those obtained for non-reinforced polyester material (2639 MPa and 5.82 J/m, respectively), and lower than the glass fiber composite (5526 MPa and 207.46 J/m, respectively); while the tensile and flexural strength obtained for the cabuya composite (34.5 MPa and 32.6 MPa, respectively) were lower than the unreinforced (52.6 MPa and 62.9 MPa, respectively) and glass fiber reinforced polyester (87.3 MPa and 155 MPa, respectively).  相似文献   

18.
Denim, a twilled cotton fabric, was used to enhance the mechanical and thermal properties of poly(lactic acid) (PLA). The denim fabric reinforced composites with different numbers of denim layers were fabricated by using a hand layup method. The impact, tensile, and dynamic mechanical properties of the composites were observed with increasing denim layers to examine the reinforcing effect of denim fabrics. Numerical analysis was carried out to model the elastic modulus of the composite by using a commercial software. Three-dimensional geometry of the denim fabric reinforced PLA composite was generated through a CAD program, and the elastic modulus was calculated by applying uniform deformation on one surface. The impact strength, tensile strength, and thermal properties of the composites were improved by piling denim fabrics. The denim fabric reinforced composites exhibited outstanding impact strength due to the retarded crack propagation as well as large energy dissipation. The 3 layer denim reinforced composite showed best results among all specimens, and its impact strength, tensile strength, and tensile modulus were measured to be 82 J/m, 75.76 MPa, and 4.65 GPa, respectively. The PLA/denim composites have good mechanical properties and can substitute traditional composites such as glass fiber or carbon fiber reinforced composites.  相似文献   

19.
In this study, we describe the preparation and characterization of electrospun Nylon66 composite nanofibers incorporated with carbon nanotubes (CNT) fillers and silver nanoparticles. We have incorporated the composites in to Nylon66 nanofibers to enhance the characteristics of the resultant composite nanofibers. The resultant composite nanofibers were characterized by using field-emission scanning electron microscopy, energy dispersive X-ray analysis, high-resolution transmission electron microscopy, X-ray diffraction, and current-voltage (I–V) measurement analysis. The morphology of the composite nanofibers exhibited densely arranged mesh-like ultrafine nanofibers which were strongly bound in between the main fibers. From I–V characteristics, it was observed that the incorporation of CNT fillers and Ag nanoparticles in to electrospun Nylon66 composite nanofibers can be significantly enhanced the electrical properties.  相似文献   

20.
This study aims to investigate the effects of two types of wood flour; oil palm mesocarp flour (OMF) and rubberwood flour (RWF), and their particle sizes on mechanical, physical, and thermal properties of wood flour reinforced recycled polypropylene (rPP) composites. The composite materials were manufactured into panels by using a twin-screw extruder. The rPP composites based on RWF significantly showed higher flexural, tensile, and compressive properties (both strength and modulus) as well as hardness and thermal stability than those composites based on OMF for the same particle sizes. However, distribution of RWF in the rPP matrix was less homogeneous than that of the rPP/OMF composites. Furthermore, a decrease of the particle sizes of filler for the rPP/OMF or RWF composites increased the flexural, tensile, compressive, and hardness properties. Likewise, the thermal stability of both OMF and RWF composites were insignificantly affected by the particle sizes.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号