共查询到20条相似文献，搜索用时 625 毫秒
1.
Pseudo-lignin induced by high-severity dilute acid treatment of lignocellulose has been widely studied because of its detrimental effect on enzymatic hydrolysis. However, cooling-induced pseudo-lignin (CIPL) formed during the cooling process after treatment has always been ignored and never been characterized systematically. To investigate the formation and chemistry of CIPL, liquid hot water treatments of poplar wood were conducted. Samples of treated wood and hydrolysate were taken out from digester at various temperatures during the cooling process for characterization. SEM images evidenced a progressive deposition of CIPL on the surface of the treated wood during cooling process with a yield of 19.6 mg/g treated wood. However, the treated wood which was collected isothermally at reaction temperature showed no pseudo-lignin. Variation of organic compounds in hydrolysate from lignocellulose degradation during cooling process revealed that depolymerized lignin and furfural accounted for 80.4 and 10.6 % of CIPL, respectively, while soluble saccharides from carbohydrate hydrolysis were independent from CIPL formation. These findings stress the importance of isothermal separation of treated wood and hydrolysate. Otherwise, CIPL should hinder enzymatic hydrolysis for biofuels production or delignification for cellulosic fiber production. 相似文献
2.
稀酸预处理改善玉米秸秆酶水解性能的机制探讨 总被引：1，自引：0，他引：1
为了探讨在稀酸预处理提高玉米秸秆在纤维素酶酶解阶段提高纤维素转化率的机制,利用一系列的检测方法:FT-IR、XRD、SEM和比表面积分析仪分析了预处理前后玉米秸秆在形态学和物理化学性质方面的变化.在经过稀酸预处理后的玉米秸秆在纤维素酶酶解阶段其纤维素转化率有较大的提高,经过170℃,60 min,固液比1∶15(g∶mL),1.00 g/mL酸质量浓度的条件预处理后,从31.88％提高到95.74％.XRD结果显示预处理后玉米秸秆的结晶度有所增加,从原料的37.8％增加到58.7％,但是当预处理强度增加到一定程度后,结晶度没有较大的变化,基本维持在58％.玉米秸秆的表面结构在稀酸预处理后,原来的光滑表面变得粗糙、多孔,这样的表面有利于纤维素酶与玉米秸秆的接触,预处理后玉米秸秆的比表面积有很大程度的增加,经过170℃,60 min,固液比1∶15,1.00g/mL酸质量浓度的条件预处理后,玉米秸秆的比表面积从0.329 m2/g增加到2.878 m2/g,这都有利于改善纤维素酶对纤维素的作用,增加纤维素转化率. 相似文献
3.
4.
Dai Oka Kayoko Kobayashi Noriyuki Isobe Yu Ogawa Tomoya Yokoyama Satoshi Kimura Ung-Jin Kim Ken Tokuyasu Masahisa Wada 《Journal of Wood Science》2013,59(6):484-488
Pulverized samples of wood, cedar and eucalyptus were treated with 5 N NaOH solutions at 25–150 °C. Hemicellulose and lignin content in the samples decreased with increasing treatment temperatures, while the recovery of glucose was maintained at nearly 90 %. X-ray diffraction analysis showed that the content of the original cellulose I structure in the samples decreased with increasing temperature, and most of the cellulose in the sample treated at 150 °C was converted to cellulose II by mercerization. Enzymatic hydrolysis of the alkaline-treated samples was carried out at 37 °C using solutions comprising a mixture of cellulase and β-glucosidase. The samples treated at higher temperatures showed better enzymatic degradability. Treatment with an alkaline solution of lower concentration (1 N NaOH) at 150 °C was also used. Despite significant quantities of hemicellulose and lignin being removed, mercerization was not induced. The enzymatic degradability was much lower than that of the sample treated with a 5 N NaOH solution at 150 °C. Thus, treatment with concentrated alkaline solution at high temperature led to not only the removal of hemicellulose and lignin, but also to modification of the cellulose structure, which resulted in high efficiency of enzymatic saccharification of the wood samples. 相似文献
5.
木质生物资源的水解 总被引：17，自引：3，他引：14
水解是利用木质生物资源以生物转化法制取乙醇的重要步骤,水解技术主要包括稀酸水解、浓酸水解和酶水解。酶水解的特点是具有选择性,降解产物少,葡萄糖得率高,能耗较低,不要求反应器具有高耐腐蚀性,被视为最有潜力降低乙醇生产成本的突破口。目前,利用木质生物资源制取乙醇还没有进入工业化生产。其原因在于成本高于利用淀粉和糖料,原料的预处理成本高、纤维素酶的生产成本高、酶活力低、纤维素的酶水解效率低、酶用量大、对半纤维素的有效利用不够。因此,需要研发有效的预处理工艺,提高纤维素底物的生物酶可及度;筛选高效纤维素酶、优化酶水解工艺,提高纤维素的水解率;利用基因重组的发酵性微生物,把戊糖发酵成乙醇,提高乙醇的产量,降低生产成本。 相似文献
6.
In a poplar clonal plantation with different species and hybrids, established at 13,333 cuttings ha?1, biomass production was assessed at the end of the first rotation (3 years) and the potential of the different clones for sugar production was evaluated. The highest biomass production was observed for clones ‘AF2’ and ‘Viriato’ (46.5 and 42 t dm ha?1, respectively). After a mild acid pretreatment and an enzymatic saccharification, the highest sugar digestibility was found for ‘Viriato’ and ‘Unal’. A clear relation between sugar digestibility and xylan removal during pretreatment was observed, while no relation with lignin content was found. Taking into account the results, the highest production of sugars per hectare was estimated for the poplar clone ‘Viriato’, being 18–48% higher than that achieved with the other clones. Therefore, this clone is a promising candidate to be used as feedstock for sugar production in a forest biorefinery. 相似文献
7.
选取三倍体毛白杨为原料,通过分析最优条件下有机溶剂法和蒸汽爆破法预处理后纤维素得率、结晶度指数、木质素含量及酶水解的结果,比较两种预处理工艺对底物性质的影响。结果表明:蒸汽爆破法能脱出部分木质素,而有机溶剂法能使大部分木质素脱除,木质素质量分数比未处理的降低63.34%。与原料相比,经过预处理后,结晶度指数都有所提高,蒸汽爆破预处理后达1.962,有机溶剂法预处理后达1.712。有机溶剂法预处理的样品葡萄糖转化率为81.36%,蒸汽爆破预处理的样品的葡萄糖转化率可达91.29%。 相似文献
8.
Dr. G. Ucar 《Wood Science and Technology》1990,24(2):171-180
Summary The dilute acid pretreatment in a plug flow reactor and alkali pretreatments with caustic solutions at different conditions followed by enzymatic hydrolysis resulted in drastically improved glucose yields for aspen and hybrid poplar. The acid pretreatment conditions must be carefully chosen to open the cellulosic structure allowing rapid diffusion of enzyme. The effectiveness of pretreatment is chiefly based on the enlargement of the pore size suitable for enzyme molecules.This work was carried out at Thayer School of Engineering, Dartmouth College in New Hampshire. The author wishes to express his gratitude to Prof. H. E. Grethlein for all kind support and helpful discussions 相似文献
9.
碱性过氧化氢预处理糠醛渣超声波辅助酶解研究 总被引：1，自引：0，他引：1
以糠醛渣为原料进行碱性过氧化氢法预处理,采用超声波辅助酶解法,比较分析不同模式下的葡萄糖转化率及水解液残存酶活。研究结果表明:酶解2 h时辅以超声波是糖转化的最佳条件,超声波辅助酶解及分段加酶使糖产率由55.01%提高到73.35%。超声波的机械作用影响着酶的吸附与脱附,有利于其与底物的充分结合。不同超声波酶解模式对糖产率的影响较大,且U-C模式效果较好,使糖产率提高46.35%。同时,酶解前超声波可以使糖产率提高33.34%。可见,低能耗,低污染的碱性过氧化氢预处理糠醛渣超声波辅助酶解为工业化生产乙醇提供了良好的发展方向。 相似文献
10.
11.
Umi Hamidah Takuya Arakawa Yin Ying H’ng Akiko Nakagawa-izumi Masanori Kishino 《Journal of Wood Science》2018,64(2):149-156
In this work, pretreatment of wood meals using a recycled ionic liquid (IL), 1-ethyl-3-methylimidazolium acetate ([Emim]Ac), enhanced glucose liberation by enzymatic saccharification, without dissolution of cellulose and lignin. In contrast, previous studies on IL pretreatment have mostly focused on lignocellulosic dissolution to regenerate cellulose and removing lignin. Softwood (Cryptomeria japonica) was pretreated with [Emim]Ac at 60–100 °C for 2–8 h without collecting regenerated cellulose. The pretreatment did not have a strong effect on wood component dissolution (weight of residues: 91.7–98.8%). The residues contained relatively high amounts of lignin (26.6–32.6%) with low adsorption of [Emim]Ac (0.9–2.7%). Meanwhile, the crystallinity index (C r I) of cellulose in the wood was significantly reduced by pretreatment, from 50.9% to 28.4–37.1%. In spite of the high lignin contents in the residues, their glucose liberation values by enzymatic saccharification using a cellulase mixture were 3–16 times greater than that of untreated wood. A good correlation was found between the saccharification effectiveness of pretreated samples and the C r I. Although lignin dissolved in [Emim]Ac continued to accumulate after repeated use of [Emim]Ac, the pretreatment was found to be effective for three consecutive cycles without the need to remove the dissolved materials. 相似文献
12.
生物质制乙醇是解决当前世界能源短缺的重要途径。当前生物质制乙醇在国内外无法大规模投入生产的主要原因是成本过高。选取优质的生物质材料和高效的预处理方法可以有效解决这一问题。以6个泡桐品种为试验材料,采用稀硫酸、氢氧化钠、微波-氢氧化钠3种方法进行预处理,对泡桐纤维素含量和酶解后还原糖产量进行测定,探讨不同预处理方法对纤维素含量和还原糖产量的影响。结果表明:以微波-氢氧化钠法预处理毛泡桐品种效果良好,处理后纤维素含量达84.82%,较预处理前提升了38.01%;半纤维素和木质素分别降低了21.23%和6.65%;还原糖产量较高,为471.38 mg/g。该研究可为生物质制乙醇高效预处理方法和优质生物质材料的选择提供参考。 相似文献
13.
以美洲黑杨种内杂交得到的29个后代雌株为材料,对杨絮的空间分布、杨絮量、结实量、生长量等相关的10个数量性状进行调查分析,研究了杨絮的影响因素,并筛选杨树少絮优良无性系。结果表明:杨絮主要集中于树冠的集花区,花枝数、果序数、杨絮量及种子量在冠层中的分布均表现为中部上部下部。单株杨絮量与单株花枝数及平均冠幅呈极显著相关,与平均胸径、集花区长、单果序种子数、单株果序数、单株种子数呈显著相关;与树高及枝下高不相关。遗传变异分析表明:各性状在杂交子代中均达到极显著差异且大都属于高水平重复力,且差异主要受遗传因素控制。从调查的8个相关性状中选出可代表杨絮量、集花区、单果序结实量等相关指标的3个主成分,代表了8个调查性状信息总量的75.487%。最后,依据主成分得分及相关性状综合评选出了92、121和260三个少絮无性系。 相似文献
14.
Steam explosion (SE) pretreatment produces damaged and disintegrated biomass with a large surface area which facilitates enzymatic hydrolysis for the production of biofuels and other value-added chemicals. It was observed during experiments that wood chips disintegrate into smaller pieces because of collisions and impact with each other and the walls of the SE equipment. In this study, these events were simulated using the finite element method. Wood chips were simulated in this model as a linear elastic material until failure. The damage initiation was identified using Hashin’s damage initiation criteria. Once the damage was initiated, additional loading caused the evolution of damage, i.e. degradation and breakage of the material, which was modelled using the material property degradation model and deletion of the failed elements. Elastic and strength properties of spruce wood were estimated at ambient conditions (12 % moisture content at 20 °C) and at SE conditions (30 % moisture content at 160 °C). Comparison of simulations performed using material properties at ambient and SE conditions revealed that the damage in wood chips significantly increased because of the steam treatment. The effects of wood chip velocity and orientation at the time of impact were studied as well. It was found that wood chips moving at high velocity and impacting with the steel wall in the radial direction acquire the most damage. 相似文献
15.
16.
酸催化的蒸汽爆破预处理强度对麦草酶水解影响的研究 总被引：7，自引：0，他引：7
以蒸汽爆破法对0.5 %的稀硫酸浸渍的麦草进行预处理,研究了不同处理强度对麦草浆得率、半纤维素回收率、纤维素回收率、纤维素酶水解得率产生的影响.实验结果表明,在蒸汽爆破预处理过程中,麦草纤维组分发生分离.随着处理强度的提高,粗浆得率降低,细浆得率上升,纤维素的降解程度和半纤维素的去除程度提高,酶水解得率相应提高.在处理强度为4.14的预处理条件下,半纤维素的水解程度最大,而细浆得率和纤维素的酶解得率最高,分别为62.0 %和73.4 %;最佳的处理强度为3.55,此条件下,汽爆麦草原料细浆中的葡萄糖得率和滤出液中总糖的得率最高,分别为20.0 %和13.0%. 相似文献
17.
Minzhen Bao Xianai Huang Mingliang Jiang Wenji Yu Yanglun Yu 《Journal of Wood Science》2017,63(6):591-605
This study aimed at developing a thermo-hydro-mechanical (THM) processing to compress poplar wood and investigating the effects of high temperature, moisture, and pressure during the THM processing on the changes in microstructure, porosity, mechanical properties, and dimensional stability of compressed poplar wood. The variations in these properties were correlated and their mathematical relations were determined. Poplar woods with high moisture content were compressed using different pressures at a temperature of 160 °C for different periods. The compression level was characterized by the volume compression ratio (CR), which is defined as the ratio of the compression volume and the original volume of sample before and after THM processing. The obtained results indicated that the high pressure of THM process caused the collapsing of wood cell lumens and the developing of a certain amount of fractures in the cell wall. The damage level of wood cells increased with increasing pressure and time. Moreover, the pressure narrowed the cell lumens, which decreased significantly the pore volume in wood substrate. The pore size distribution shifted from the level of macropores to those of mesopores and micropores after THM process. The THM process created superior mechanical property, especially for those with higher CR. Besides, it was revealed that the process decreased dramatically the set recovery of treated woods and improved their dimensional stability. A significant improvement was achieved in terms of the mechanical and physical properties of compressed poplar wood via the structural reformation during the THM process. 相似文献
18.
亚硫酸盐预处理对蔗渣酶解效率的影响 总被引：1，自引：0，他引：1
为了破坏蔗渣的抗降解性,获得高的酶解效率,采用亚硫酸盐法对蔗渣进行预处理,探讨亚硫酸氢钠用量对蔗渣理化性质、表面磺酸基含量(磺化度)及酶解效率的影响,并进一步分析了磺化度对酶解效率的影响。结果显示:不同亚硫酸氢钠用量蔗渣的结晶度(I_(Cr))变化不显著,但预处理后蔗渣纤维素结晶区相对含量上升,半纤维素含量减少。50 g蔗渣,按固液比1∶8(g∶m L)加入1.1%的稀硫酸,亚硫酸氢钠加入量(以绝干蔗渣计)为8%,在160℃条件下反应30 min时制得的蔗渣其表面磺酸基最多,达131.73μmol/g。在2%干蔗渣,7.5 FPU/g(以干蔗渣计),50℃,72 h酶解条件下,对不同磺化度的蔗渣进行酶解,结果显示酶解效率随底物的磺化度升高而升高,最高综纤维素水解效率可达83.76%。研究表明:蔗渣的酶解效率与磺酸基团的含量呈正相关,而与蔗渣中纤维素的结晶度关系不明显;酸性亚硫酸盐法可除去绝大部分半纤维素,破坏蔗渣抗降解性,促进酶解效率。 相似文献
19.
杨树微纤丝角的变异及其与木材性质的相关关系 总被引：6，自引：0，他引：6
微纤丝角为细胞次生壁S2层微纤丝排列方向与细胞主轴所形成的夹角,与木材的物理性质、力学性质和化学性质都有着直接的关系。应用x射线衍射法测定了7个杨树无性系(14株样木)胸径处各年轮的微纤丝角,并对应分析和测定了各年轮的木材基本密度、纤维长度、纤维宽度和纤维素含量。研究结果表明,杨树微纤丝角在年轮间存在显著差异,其径向变异规律为从髓心向外以微纤丝角逐渐降低,年轮间的平均微纤丝角在7.8旱?8褐洌荒静幕久芏取⑾宋ざ取⑾宋矶群拖宋睾吭谀曷旨湟泊嬖谙灾钜臁O喙胤治霰砻鳎⑾怂拷怯肽静幕久芏取⑾宋ざ取⑾宋矶群拖宋睾看嬖谙灾母合喙毓叵??0.01),相关系数分别为-0.450、-0.586、-0.516和-0.660。回归分析结果表明,多项式方程可较好地描述杨树微纤丝角与所测定的木材性质的关系,相关系数均在-0.45以上(n=125)。本文的研究结果认为,在今后针对杨树材性改良的育种计划中,微纤丝角是一个重要的选育和改良指标。图3表3参34。 相似文献
20.
杨树新无性系木材性质的变异研究 总被引：4，自引：0，他引：4
The wood basic density, cellulose content and fiber form were investigated for all sample trees at breast height (1.3m) in seven poplar clones, and at 0 (butt), 5.6, 9.6, 13.6, 17.6, 19.6 and 21.6 m for clone Nanlin-95 and Nanlin-895, respectively,for providing information on variation patterns of wood density, fiber characteristics and holocellulose content within trees and among clones. The results showed that significant variations about wood density, cellulose content, fiber diameter and the ratio of fiber length to diameter existed among poplar clones examined. Variance analysis indicated that there were significant differences in wood basic density, fiber length, fiber diameter and cellulose content among the growth rings, which had an increasing tendency along the direction from pith to bark. The significant differences also existed in wood basic density, fiber length and fiber diameter at different tree height. The mean wood basic density had a general increase trend with increasing height of trees and the lowest was found at the base, while fiber length and fiber diameter had a general decline pattern with increasing height of trees and the biggest value was observed at the height of 5.6 m. Regression analysis indicated that the relationship between examined wood properties and growth ring number (cambial age), and the relationship between examined wood properties and tree height can be described by polynomial functions. 相似文献