首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 15 毫秒
1.
Effects of zinc-oxide nanoparticles on physical and mechanical properties, as well as biological resistance of untreated and heat-treated beech wood were investigated in this study. Test specimens were prepared from sapwood and impregnated with a 5,000-ppm nano-zinc-oxide (NZ) suspension with a size ranging from 10 to 80 nm at 2.5 bars of pressure and using the Rueping process for 20 min. Control (C) and nano-zinc-oxide-impregnated specimens after (NZA) and before (NZB) heat treatment were divided into four subgroups of unheated (C and CNZ), heated at 50, 145 and 185 °C. Heat treatment resulted in a significant decrease in mechanical strength at temperatures of 145 and 185 °C. Heat-treated specimens showed less dimensional instability and fungal degradation. Impregnation with nano-zinc resulted in a slight and significant increase in weight loss and biological resistance against Trametes versicolor. The results showed that the impregnation significantly decreased the water absorption of the specimens. Impregnation before heat treatment showed considerable effect on the properties of wood compared to that of untreated ones.  相似文献   

2.
Wood modification, of which thermal modification is one of the best-known methods, offers possible improvement in wood properties without imposing undue strain on the environment. This study investigates improvement of the properties of heat-treated solid wood. Scots pine (Pinus sylvestris) was modified in two stages: impregnation with modifiers followed by heat treatment at different temperatures. The impregnation was done with water glass, melamine, silicone, and tall oil. The heat treatment was performed at the temperatures of 180°C and 212°C for three hours. The modified samples were analyzed using performance indicators and scanning electron microscope micrographs. The mechanical and physical properties were determined with water absorption, swelling, bending strength, and impact strength tests. All the modifiers penetrated better into sapwood than hardwood; however, there were significant differences in the impregnation behavior of the modifiers. As regards the effect of heat treatment, generally the moisture properties were improved and mechanical strengths impaired with increasing treatment temperature. In contrast to previous studies, the bending strength increased after melamine impregnation and mild heat treatment. It is concluded that the properties of impregnated wood can be enhanced by moderate heat treatment.  相似文献   

3.
We evaluated fungal decay and mold resistance, leaching, and water absorption of nano-compounds and Paraloid B72® (PB72) in treated wood specimens to develop new methods of consolidation by combining nano-particles and consolidants. Scots pine wood specimens were treated with dispersions of nano-CuO, nano-ZnO, nano-B2O3, nano-TiO2, and nano-CeO2. PB72 treatments of nano-particle-treated wood specimens were then carried out by either vacuum or immersion for 24 h. Previously, decayed wood specimens were also consolidated with the nano-compounds and PB72. PB72 treatments reduced element release from treated wood specimens. Nearly all nano-compounds + PB72 treatments increased the biological performance of treated wood specimens against decay fungi tested. PB72-only treated wood specimens had the highest weight losses in decay tests. No improvements were obtained in mold resistance tests when the nano-compounds and PB72 were combined. In nano-compound-only treatments, unleached specimens showed slightly lower water absorption values compared to untreated control specimens. Incorporation of PB72 into nano-compound-treated wood specimens resulted in considerably lower water absorption and volumetric swell. In previously decayed specimens treated with the nano-compounds and PB72 solution, water absorption after 2-h immersion declined compared to control specimens.  相似文献   

4.
Heat treatment improves the dimensional stability and hydrophobicity of wood, and heat-treated wood is currently attracting attention as a new interior material. However, there are few evaluations where the acoustic properties of heat-treated wood are reported when such wood is used as an interior material. In this study, Larix kaempferi wood, typically used as a building material, was heat-treated at 200, 220, and 240 °C for 9, 12, 15, and 18 h. The sound absorption coefficients of the treated wood samples were measured at 250, 500, 1000, 2000, and 4000 Hz in a reverberation room. The sound absorption coefficient increased with the treatment temperature and the treatment time. The results of this study showed that the high-frequency band range sound absorption coefficient of wood can be increased dramatically by heat treatment.  相似文献   

5.
This research work aimed at studying the effects of oleothermal modification of fir wood by using combined soybean oil with maleic anhydride (OHT–MA) to achieve lower treatment temperatures and enhance physico-mechanical properties. Wood blocks were oleothermally treated with soybean oil and OHT–MA at five different treatment temperatures (100, 120, 140, 160 and 180 °C) for three different holding times (30, 60 and 180 min). Afterward, physical and mechanical properties of the treated samples were determined, i.e., density, water absorption and volumetric swelling as the physical properties and bending strength, compression parallel to grain and impact load resistance as the mechanical properties. Results revealed increases in densities and reduction in water absorption as well as volumetric swelling of all treated samples. The mechanical properties were affected by OHT–MA treatment at different temperatures. Bending modulus of elasticity as well as compression parallel to grain was increased due to OHT–MA treatment. In addition, there was less reduction in impact load resistance of the treated samples. It was revealed that the OHT–MA enhanced wood properties at low treatment temperatures as well as shorter holding times.  相似文献   

6.
Heat treatment is an alternative to the chemical treatment in wood preservation, which has been used to some extent in improving timber quality. However, reduction in strength properties has been one of the major limitations in the use of this technique and therefore investigations on the use of various pre-treatment methods are highly essential. Wood samples from Scots pine were immersed in already boiling water (100°C) for 20 min followed by 2 h of heat treatment at 160 and 200°C. The acidity and strength properties were determined by measurement of pH and static bending test, respectively. There were no significant changes in pH due to preboiling in both heat-treated and untreated wood. Similarly, preboiling did not result in any appreciable differences in strength both before heat treatment and during heat treatment at 160°C. However, for 200°C heat treatment preboiling reduced significantly the degree of strength loss as indicated by 19.4% reduction in modulus of rupture in preboiled wood compared to 26.6% reduction in unpreboiled wood. From the results of this study it is evident that preboiling has a buffering effect on wood during heat treatment and the higher the intensity of heat treatment the higher the significance of the buffering effect of pre-boiling.  相似文献   

7.
The effect of heat treatment on the surface colour and hygroscopic properties of pine wood were investigated in this study. Boards of Scots pine wood (Pinus sylvestris L.) were subjected to thermal treatment at 200°C, for 4, 6, and 8 h. The change of equilibrium moisture content and density values of the specimens in order to facilitate the understanding of the treated material behavior. The colour parameters L*, a* and b*, used to depict the total colour change (Δ E) of wood surface, were shown to change proportionally to the treatment intensity. Moreover, swelling in the tangential and radial directions and absorption of the specimens appeared to be enhanced in great extent by the thermal treatment process. The mean value of swelling percentage in the tangential direction decreased 10.26%, 17.22%, and 19.60% for specimens treated for 4, 6, and 8 h, respectively, referring to the final measurement after 72 h of immersion. In radial direction, mean value of swelling percentage decreased 19.56%, 32.75%, and 34.65% for treated for 4, 6 and 8 h, respectively, after 72 h immersion, which attests the decrease in swelling and improvement in the hygroscopic behavior of Scots pine wood.  相似文献   

8.
The effect of heating on the hygroscopicity of Japanese cedar wood was investigated as a simple evaluation of thermal degradation in large-dimension timber being kiln-dried at high temperatures (>100°C). Small wood pieces were heated at 120°C in the absence of moisture (dry heating) and steamed at 60°, 90°, and 120°C with saturated water vapor over 2 weeks, and their equilibrium moisture contents (M) at 20°C and 60% relative humidity (RH) were compared with those of unheated samples. No significant change was induced by steaming at 60°C, while heating above 90°C caused loss in weight (WL) and reduction in M of wood. The effects of steaming were greater than those of dry heating at the same heating temperature. After extraction in water, the steamed wood showed additional WL and slight increase in M because of the loss of water-soluble decomposition residue. The M of heated wood decreased with increasing WL, and such a correlation became clearer after the extraction in water. On the basis of experimental correlation, the WL of local parts in large-dimension kiln-dried timber was evaluated from their M values. The results indicated that the thermal degradation of inner parts was greater than that of outer parts.  相似文献   

9.
The present study is aimed at investigating the effect of heat treatment of nano-silver-impregnated Populus nigra on weight loss, modulus of rupture (MOR), modulus of elasticity (MOE), and compression parallel to grain. Specimens were impregnated with 200 PPM water-based solution of nano-silver particles at 2.5 bar in a pressure vessel. For heat treatment, both nano-silver-impregnated and simple specimens were kept for 24 h at 45°C and then further for 24 h at 145°C and finally for 4 h at 185°C. MOR decreased from 529 to 461 kg/cm2 in heat-treated specimens; MOE and compression parallel to grain were though improved. Also, comparison between heat-treated and nano-silver-impregnated heat-treated specimens showed that there was a decrease in MOR and MOE in nano-silver-impregnated heat-treated specimens. This shows that nano-silver impregnation facilitates transfer of heat in wood and it may increase the process of degradation and pyrolysis of wood structures in deeper parts of specimens.  相似文献   

10.
In this study, twenty-five heat treatments were conducted at the various treating conditions of five temperatures and five durations. At each treatment, 15 poplar specimens were used. Twelve variables that represented wood color, physical and mechanical properties and durability were measured for both treated and untreated specimens. To evaluate the effect of heat treatment on the wood performance, a comprehensive cluster analysis was applied to the measured variables of treated and untreated specimens. Cluster analysis showed that treating and control specimens can be distinctly classified into 2, 3 or 4 clusters according to the intended purposes. Two clusters can represent the control group and twenty-five testing groups. Four clusters represented the control group and three groups of testing specimens having mild, moderate and severe treating conditions, respectively. At the mild treatment, modulus of rupture (MOR) was reduced <11 %. Wood durability increased to moderate resistant. At the moderate treatment, EMC decreased by 28 %, and MOR was decreased by more than 12 %. In the severe treatment, wood durability increased to resistant or highly resistant; however, its MOR was reduced half.  相似文献   

11.
In this study, the use of polyvinyl alcohol (PVA) as boron fixative agent was investigated. Two levels of PVA (2.5 and 4%) were evaluated with disodium octaborate tetrahydrate (DOT) at three concentrations (1, 2 and 4% boric acid equivalent (BAE)) using a double vacuum impregnation process on Scots pine sapwood specimens. Leaching was performed according to a laboratory leaching procedure. Boron analysis using atomic absorption spectrometer showed a significant reduction in boron leachability for the samples treated with both concentrations of PVA when compared to the stand-alone boron treatment leading to boron retentions capable of preventing wood biological degradations. Decay resistance of the leached specimens was evaluated using the brown rot fungus Poria placenta. Even if complete protection was not fully achieved, an improvement in decay resistance was observed for the samples treated with DOT in presence of PVA. This leak of efficacy was attributed to a decrease in the biological activity of the complexed boron against fungi. Durability of treated wood against termite attack, evaluated using Reticulitermes santonensis, indicated a significant enhancement for the samples treated in presence of the fixative agent compared to the pure boron treatment.  相似文献   

12.
There is a lack of quantitative data on the penetration depth and the amount of energy absorbed by green wood under infrared (IR) radiation. This lack of knowledge is a potential barrier to the development of IR heating as an alternative to soaking as a means of warming logs prior to peeling in the manufacture of plywood. Experimental measurements of normal hemispherical spectral reflectance and transmittance over the range 550–5,500 cm?1 wavenumbers on four wood species, beech, birch, Douglas-fir and spruce have brought new knowledge on mid-infrared absorption properties of green wood and removed some uncertainties. For instance, it is not possible to deliver energy deeper than up to 0.3 mm below the wood surface because 70–90 % of all incident IR radiation on the wood surface is absorbed in this layer. Some wood features, such as surface quality, the presence of knots and of free water in wood (the latter two having a more significant effect) influence the amount of energy absorbed. These results illustrate that IR radiation can heat the surface layers, but then heat penetrates deeper into the inside layers of wood by conduction.  相似文献   

13.
This study aimed to evaluate physical and mechanical properties and colour changes of fast-growing Gympie messmate wood subjected to two-step steam-heat treatments. To achieve this, Gympie messmate wood was thermally treated under different conditions. Combined steam (127°C and ～0,1471 MPa) and heat treatments in an oven (180–240°C for 4 hours) were performed. Physical and mechanical properties were evaluated by weight loss, equilibrium moisture content, specific gravity, volumetric and linear swelling and static bending tests, while colour changes were studied using CIEL*a*b* technique. The main findings showed that the steam pre-treatment in autoclave influenced most of the technological properties evaluated, mainly for heat treatments performed in low temperatures (180–200°C). The most significant changes after thermal treatments were observed for dimensional stability, which increased as a function of temperature of treatment. On the other hand, mechanical strength of thermally modified wood was significantly affected, while stiffness did not change. Colour modifications due to the application of two-step steam-heat treatments confirm the possibility to using these samples for aesthetic purposes.  相似文献   

14.
Abstract

Two Malaysian hardwoods, acacia (Acacia mangium) and sesendok (Endospermum malaccense), that had been subjected to oleo-thermal modification were studied to determine their sorption isotherm behaviour using a dynamic vapour sorption apparatus. All the specimens were thermally modified using palm oil at three different temperatures (180, 200 and 220°C) and three different times (1, 2 and 3 h). The results showed that there was a reduction in equilibrium moisture content at each target relative humidity due to the heat treatment, but that the two wood species showed different behaviour in this respect. The adsorption isotherms were analysed using the Hailwood and Horrobin model, with excellent fits to the experimental data. The monolayer water and polylayer water were both reduced at a range of relative humidity values of the treated samples, although behaviour between the two wood species differed. Heat treatment resulted in an increase in hysteresis ratio, which was probably due to the increase in matrix stiffness of the cell walls.  相似文献   

15.
Japanese cedar wood specimens were steamed at 80°, 100°, and 120°C over 14 days, and their equilibrium moisture content (M) at 20°C and 60% relative humidity, longitudinal dynamic Young’s modulus (E), bending strength (σ max), and breaking strain (ε max) were compared with those of unheated specimens. Steaming for a longer duration at a higher temperature resulted in a greater reduction in M, σ max, and ε max. The E of wood was slightly enhanced by steaming at 100°C for 1–4 days and 120°C for 1–2 days, and thereafter it decreased. The slight increase in the E of sapwood was attributable to the reduction in hygroscopicity, while sufficient explanation was not given for a greater increase in the heartwood stiffness. Irrespective of the steaming temperature, the correlations between M and the mechanical properties of steamed wood were expressed in terms of simple curves. M values above 8% indicated a slight reduction in E and s max, whereas M values below 8% indicated a marked decrease in the mechanical performances. In addition, the e max decreased almost linearly with a decrease in the value of M. These results suggest that hygroscopicity measurement enables the evaluation of degradation in the mechanical performances of wood caused by steaming at high temperatures.  相似文献   

16.
Thermal modification at relatively high temperatures (ranging from 150 to 260 °C) is an effective method to improve the dimensional stability and resistance against fungal attack. This study was performed to investigate the impact of heat treatment on the mechanical properties of wood. An industrially-used two-stage heat treatment method under relative mild conditions (< 200 °C) was used to treat the boards. Heat treatment revealed a clear effect on the mechanical properties of softwood species. The tensile strength parallel to the grain showed a rather large decrease, whereas the compressive strength parallel to the fibre increased after heat treatment. The bending strength, which is a combination of the tensile stress, compressive stress and shear stress, was lower after heat treatment. This decrease was less than the decrease of only the tensile strength. The impact strength showed a rather large decrease after heat treatment. An increase of the modulus of elasticity during the bending test has been noticed after heat treatment. Changes and/or modifications of the main wood components appear to be involved in the effects of heat treatment on the mechanical properties. The possible effect of degradation and modification of hemicelluloses, degradation and/or crystallization of amorphous cellulose, and polycondensation reactions of lignin on the mechanical properties of heat treated wood have been discussed. The effect of natural defects, such as knots, resin pockets, abnormal slope of grain and reaction wood, on the strength properties of wood appeared to be affected by heat treatment. Nevertheless, heat treated timber shows potential for use in constructions, but it is important to carefully consider the stresses that occur in a construction and some practical consequences when heat treated timber is used.  相似文献   

17.
Effect of heat treatment intensity on some conferred properties like elemental composition, durability, anti-swelling efficiency (ASE) and equilibrium moisture content (EMC) of different European softwood and hardwood species subjected to mild pyrolysis at 230 °C under nitrogen for different durations has been investigated. Independently of the wood species studied, elemental composition is strongly correlated with the mass losses due to thermal degradations which are directly connected to treatment intensity (duration). In all cases, an important increase in the carbon content associated with a decrease in the oxygen content was observed. Heat-treated specimens were exposed to several brown rot fungi, and the weight losses due to fungal degradation were determined after 16 weeks, while effect of wood extractives before and after thermal treatment was investigated on mycelium growth. ASE and EMC were also evaluated. Results indicated important correlations between treatment intensity and all of the wood conferred properties like its elemental composition, durability, ASE or EMC. These results clearly indicated that chemical modifications of wood cell wall polymers are directly responsible for wood decay durability improvement, but also for its improved dimensional stability as well as its reduced capability for water adsorption. All these modifications of wood properties appeared simultaneously and progressively with the increase in treatment intensity depending on treatment duration. At the same time, effect of extractives generated during thermal treatment on Poria placenta growth indicated that these latter ones have no beneficial effect on wood durability.  相似文献   

18.
Optimisation of a two-stage heat treatment process: durability aspects   总被引：1，自引：1，他引：1  
Heat treatment of wood at relatively high temperatures (in the range of 150–280°C) is an effective method to improve biological durability of wood. This study was performed to investigate the effect of heat treatment process optimisation on the resistance against fungal attack, including basidiomycetes, molds and blue stain fungi. An industrially used two-stage heat treatment method under relatively mild conditions (<200°C) was used to treat the boards. Heat treatment of radiata pine sapwood revealed a clear improvement of the resistance against the brown rot fungi Coniophora puteana and Poria placenta. Increasing process temperature and/or effective process time during the first process stage, the hydro thermolysis, appeared to affect the resistance against C. puteana attack, but the effect on the resistance against P. placenta was rather limited. Heat treated radiata pine showed a limited resistance against the white rot fungus Coriolus versicolor and process variations during the hydro thermolysis stage appeared not to affect this resistance. A clear difference between the resistance of heat treated Scots pine sapwood and heartwood against fungal attack is observed. Scots pine heartwood showed a higher resistance against C. puteana and P. placenta but also against the white rot fungus C. versicolor. Similar results were obtained when heat treated birch was exposed to brown and white rot fungi. Heat treatment showed an improved resistance against C. puteana attack, especially at higher temperatures during the hydro thermolysis stage. A clear improvement of the durability was also observed after exposure to the white rot fungus C. versicolor and especially Stereum hirsutum. Increasing the process temperature or process time during the hydro thermolysis stage appeared to have a limited effect on the resistance against C. versicolor attack. Heat treated radiata pine and Norway spruce were still susceptible to mold growth on the wood surface, probably due to the formation of hemicelluloses degradation products (e.g. sugars) during heat treatment. Remarkable is the absence of blue stain fungi on heat treated wood specimen, also because the abandant blue stain fungi were observed on untreated specimen. Molecular reasons for the resistance of heat treated wood against fungal attack are discussed in detail contributing to a better understanding of heat treatment methods.  相似文献   

19.
Thermal treatment is an alternative to the chemical treatment in wood preservation, which has been used to some extent in improving timber quality. Despite the enormous works done so far on the effects of heat treatment on wood properties, very little is known about the anatomical changes in the various wood species during the process. Wood samples from western red cedar (Thuja plicata) were heat-treated at a temperature of 220°C for 1 and 2 h. The anatomical structures were examined before and after the heat treatment process by using scanning electron microscope (SEM) and related to density, water uptake, thickness swelling and modulus of rupture of wood samples obtained from the same board. Heat treatment of red cedar wood resulted in the destruction of tracheid walls, ray tissues and pit deaspiration. The destroyed tracheid walls and ray tissues appeared to blow up, thus increasing the size of the specimen. The process of pit deaspiration also resulted in increasing size of the pits, thus creating more openings in the wood. These changes in wood anatomy indicate that the well-established chemical degradation is not the only reason for changes in wood properties during heat treatment. However, it is believed that the effects of the chemical changes still outweigh those of the anatomical changes based on the modification observed during the process of heat treatment.  相似文献   

20.
Abstract

Chitosan is a biopolymer derived from chitin in crustacean shells. Over the past decade it has been studied as an environmentally benign wood-protecting agent. It is assumed to act as a fungi-stat against a wide range of fungi and even as a fungicide at higher concentrations. This study investigated the properties of wood treated with modified chitosan of different molecular weights. Scots pine (Pinus sylvestris L.) and beech (Fagus sylvatica L.) samples were impregnated with two chitosan solutions differing in their average molecular weights. The chitosan solutions were depolymerized by nitrous acid to one solution of high molecular weight and one solution of low molecular weight with a concentration of 5% (w/v). The results show changes in sorption properties, antifungal properties, fire-retardant properties and mechanical properties of modified chitosan-treated wood. Heat-modified, chitosan-treated wood showed similar properties to chitosan-treated wood, except for brownish coloration, enhanced hydrophobation, and slightly reduced antifungal and fire-retardant properties. The modulus of rupture and hardness showed little or no change. The modulus of elasticity of the heat-modified, chitosan-treated wood increased by 27% compared with untreated wood.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号