共查询到20条相似文献，搜索用时 15 毫秒
1.
A new method for monitoring moisture content during radio-frequency (RF)/vacuum drying was developed by measurement of temperature
and pressure in wood. Temperature and pressure inside the wood were measured simultaneously during RF/vacuum drying at the
same point. The relative humidity (RH) and moisture content (MC) below the fiber saturation point (FSP) were calculated based
on temperature and pressure, and the relationship between the temperature, RH, and equilibrium moisture content (EMC) at the
measurement point. When the moisture content was below the FSP, the calculated MC was slightly greater than the value given
by oven drying. The absolute error was within 0.8% near the open cross side, and was within 1.8% at another measurement point.
Thus, we concluded that it was practicable to monitor the moisture content below the FSP according to the temperature and
pressure inside the wood.
Part of this study was presented at the 15th Annual Meeting of the Chugoku Shikoku Branch of the Japan Wood Research Society,
Higashi-Hiroshima, Japan, September 2003 相似文献
2.
The purpose of this study was to compare the distribution of moisture contents (MCs) along the radial direction during radio-frequency/vacuum (RF/V) drying of log cross sections of heartwood (HLC) where sapwood was removed from a green log cross section and log cross section of mixed sapwood and heartwood (MLC) prepared with debarked logs of Japanese larch (Larix leptolepis) and locust (Robinia pseudoacacia). For Japanese larch, an even distribution of MC was observed over the entire cross section in HLC not only at the initial stage of drying but also up to the completion of drying. Furthermore, the moisture gradient between the outermost slice and the adjacent inner slice was more gradual compared with that in MLC. For locust, the moisture gradient between the outermost slice and the adjacent inner slice became severe as drying progressed. It decreased after reaching the maximum during the middle stage of drying but continued until the late stage of drying. Furthermore, despite the fact that the average initial MC of mixed slice within MLC was higher compared with that in heartwood slice, this trend reversed immediately after drying started. It was suggested that the possibility of formation of border checking would be high during drying the MLC, since it would be so complicate that the sapwood and heartwood reach fiber saturation point together because of differences in their green MCs and permeability between them. 相似文献
3.
《Wood material science & engineering》2013,8(1):24-33
Abstract Siberian larch (Larix sibirica Ledeb.) timber is suitable for many uses in the mechanical wood industry. Drying it without any decrease in value, however, is difficult and slow. The purpose of this research was to compare the drying quality of Siberian larch timber dried with three different conventional schedules taking into account the density and annual growth of wood. Five drying tests were performed. The final moisture content (MC), MC gradient, cracks, deformations (bow, crook, twist and cup) and case hardening were measured from the dried timber. The basic density particularly affected the MC, as shown in the differences regarding dried wood, with the denser wood having higher final MC and MC gradient. It was also found that large annual growth increased some deformations. Most of the measured factors were best after drying at the highest temperatures used; however, a slightly different trend was observed for bow, twist and cup. MC factors and twisting were the most problematic properties in drying according to this study. Sorting Siberian larch timber, particularly according to density, would improve the MC properties of dried timber by ensuring sufficient drying time, as economically as possible, for each timber piece. 相似文献
4.
5.
以白橡热压干燥材为研究对象,利用动态水分吸附仪研究了不同热压温度干燥处理后白橡木材和未处理对照材的等温吸湿特性,并采用H-H模型拟合;分析热压干燥对木材吸湿特性的降低机理。结果表明:白橡木材等温吸湿线皆为IUPAC Ⅱ型等温吸湿线。在任意相对湿度下,热压干燥材平衡含水率均明显低于对照材,且热压温度越高,平衡含水率降低越明显。H-H模型对白橡木材等温吸湿数据表现出良好的拟合效果。单分子层和多分子层含水率降低共同作用使得热压干燥材吸湿性降低,且相对湿度越高,多分子层水的减少对吸湿性的降低作用越大。与对照材相比,热压干燥材(140、150 ℃和160 ℃)的纤维饱和点推测值分别降低8.89%、11.76%和13.62%。白橡热压干燥材吸湿性降低机理主要为游离羟基等亲水基团含量减少和细胞壁刚度增加等。 相似文献
6.
Summary Thick specimens of two softwoods were dried in a laboratory radio frequency/vacuum (RF/V) kiln in order to investigate the internal moisture flow patterns. The spatial moisture distributions in the longitudinal arid transverse directions were monitored as a function of time in a number of runs. The results indicated that both longitudinal and transverse moisture transfer modes contribute on the overall moisture flow occurring within wood, but there was no distinction as to the percentage contribution of each to the overall flux. There were no abrupt drying front changes and no moisture discontinuities observed during drying. A second group of runs was also carried out using end-matched specimens to study its length effects on drying characteristics, such as drying rate, and internal vapor pressure and temperature profiles. The results demonstrated that short specimens dried faster than long ones at moisture contents above the fiber saturation point.The financial support for this work from NSERC/Canada through a Strategic Grant (STR0167393) and the lumber contribution from MacMillan-Bloedel are greatfully acknowledged. 相似文献
7.
This study was carried out to investigate the effects of end-taping of sapwood (ETS) and removal of sapwood (ROS) treatments of log cross sections on the radial distributions of moisture content (MC) and tangential strain, according to the circumferential slicing method (CSM), during radio-frequency/vacuum (RF/V) drying of log cross sections. The MC of control and ETS samples showed an even distribution around the center but decreased closer to the periphery side. In ROS samples, the MC decreased closer to the periphery side when above the hygroscopic range but showed an even distribution at the late stage of drying. Tangential strain in ETS samples showed slight compressive stress or tensile stress through the entire area of the cross section during the initial stage of drying, although the periphery side was in tensile stress from an area starting at a relative radius of 0.7. ROS samples showed tensile stress in the heartwood around the center and the heartwood of the periphery side and showed no stress or slight compressive stress in the middle area at the initial stage of drying, after which it showed an even distribution of tensile stress throughout the entire end surface. About 90% of the total checks contained in ETS and ROS samples were observed on the periphery side starting from a relative radius of 0.7. 相似文献
8.
杉木人工林木材的高频真空干燥工艺 总被引：2，自引：0，他引：2
对人工林杉木25mm和50mm厚板材进行了系列高频真空干燥试验.结果表明:干燥后的板材变形小,表面平整,表芯层含水率差异较小.尽管试板的初始含水率差异较大,但根据高频真空干燥靠近正极板的木材比靠近负极板的干燥速度快的特点,试板的初始含水率由低至高在负极板至正极板之间进行顺序摆放码垛,干燥后的板材含水率可达到均匀一致. 相似文献
9.
短周期工业材干缩率和干燥应变规律的研究 总被引：1，自引：0，他引：1
研究了短周期工业材在干燥过程中木材表层和内部各层干缩率及弹性和塑性应变的变化规律。结果表明,基准硬度水平对应变值的大小和最大变就值的到达时间有显著影响。干燥前期,木材表层伸张弹性应变最大值随着温度和平衡含水率的增加而减少,木材表层塑性应变则随平衡含水率的增加而增加。正确调节基准初期阶段的平衡含水率水平,能有效地控制干燥前期应变最大值,从而达到控制干燥质量的目的。 相似文献
10.
This study was carried out to investigate the effects of steam explosion treatment on drying rates, moisture distribution, shrinking, and checking during radio-frequency/vacuum drying of Korean larch pillar combined with a longitudinal kerf. All the pillars except the nonkerf/control with high initial moisture content (MC) could be dried within 89 h from the green condition to about 15% MC. In pillars with high initial moistures or in the early stage of drying, the drying rates were sharply accelerated by steam explosion treatments. The final moisture gradients along the transverse direction were gentler for the steamexploded pillars and for pillars with a longitudinal kerf, respectively, than for the unexploded pillars and for pillars without a longitudinal kerf. The moisture gradients along the longitudinal direction on all the layers were gentler for the pillars with a longitudinal kerf than for those without the kerf. Formation of checking was significantly controlled in the pillars with a longitudinal kerf. All the steam-exploded pillars except the kerf/1-cycle, however, were more severely damaged by checks than the unexploded pillars. A prong test revealed an extremely low level of residual stress for all the dried pillars. 相似文献
11.
Li Xian-jun Li Wen-jun Zhang Bi-guang 《中国林学(英文版)》2007,9(1):63-67
Microwave-vacuum (MV) drying characteristics of plantation Masson pine (Pinus massoniana) were studied experimen-tally for various levels of microwave radiation time, initial moisture content (MC), vacuum level and wood thickness. The results show that the process of MV drying for wood can be significantly divided into a short accelerating rate drying period, a long constant rate drying period and falling rate drying period, and the second drying period can extend to levels of mean MC below the fiber satu-r... 相似文献
12.
The effects of high temperature steam pretreatment on the change in wood moisture content (MC) and characteristics of vacuum drying were investigated in this study. Poplar and manchurian walnut woods were pretreated with high temperature steam at 100°C and 140°C, prior to vacuum drying. A comparison of the characteristics of vacuum drying between steam pretreated wood and untreated wood was carried out. The results show that during steam pretreatment, the MC of wood decreased within a few hours. The reduction of MC varied with the temperature; the higher the temperature, the faster the MC dropped. During the vacuum drying stage, the rates of drying of pretreated samples were higher than those of untreated samples when MC was below the fiber saturation point. Furthermore, the total drying time of samples treated at a steam temperature of 140°C was lower than that of untreated samples. Therefore, a vacuum procedure after steam pretreatment can effectively shorten the drying time when drying wood. 相似文献
13.
A. Tarmian R. Remond M. Faezipour A. Karimi P. Perré 《Wood Science and Technology》2009,43(1-2):113-130
The drying kinetics of reaction woods in Picea abies (compression wood) and Fagus sylvatica (tension wood) in comparison with their corresponding normal woods was investigated under constant convective drying conditions. Moisture profiles along the thickness of small flat-sawn boards taken from reaction and opposite wood zones were evaluated using a polychromatic X-ray system, a non-destructive method. The results revealed substantial differences in the drying behavior between the reaction and opposite woods. Both reaction woods represented slower drying rate than their matching normal woods mainly during the period of free water loss. However, the reaction and opposite woods reached the final moisture content (MC) of about 12% at the same time due to higher initial MC in the opposite woods. In the case of reaction wood, it took a longer time for the moisture profile to become approximately uniform. Overall, a more striking difference was observed in the drying behavior of compression and opposite wood in P. abies. Some important anatomical differences like the cell and pit dimensions and their proportion give some explanations for these drying behaviors. 相似文献
14.
A spectrophotometric assay based on the color reaction between didecyldimethylammonium chloride (DDAC) and 4-[4-(dipropylamino)phenylazo]-benzenesulfonic acid (propyl orange) was used for the determination of DDAC as a wood preservative. The assay was carried out using a propyl orange solution at pH 2.9. The visible absorbance spectrum of propyl orange showed an absorbance maximum at 510 nm, which decreased continuously with increasing DDAC concentration from 0 to 20 ppm. A linear correlation was observed at a DDAC concentration lower than 8 ppm. To apply this assay method to determine DDAC retention in treated wood, the influence of wood extractives on the assay was investigated. Wood extractives from sapwood and heartwood of Japanese cedar, Hinoki cypress, Japanese larch, and Western hemlock showed no influence on DDAC determination except in the case of heartwood from Japanese cedar and Hinoki cypress, which gave apparent DDAC concentrations higher than the actual values. However, it was also found that absorbance measurement at 477 nm solved this overestimation and gave precise values. It was concluded that this assay is a viable alternative to the current methods for DDAC determination. 相似文献
15.
木材干燥应力应变超微观模型的构筑 总被引：1，自引：0，他引：1
木材干燥应力应变研究不论在理论上探索还是用于指导生产实践,都具有重大的意义。然而木材干燥应力与应变的关系是非常复杂的,因为木材属于既有弹性又有塑性的材料———弹塑性材料。应变的大小受很多因素的影响,包括材料自身的因素,例如密度、管胞或纤维胞壁的微纤丝的角度以及恒定或变化的环境因素(如大气的温度、相对湿度)等。还有依从于时间的因素(申宗圻,1990)。正是由于木材本身的特殊结构及其在干燥过程中各参数变化的复杂性,建立一个精确性较高和适用性较广的干燥应力应变数学模型很困难。若不靠数学物理方法,单纯的试验很难重现实… 相似文献
16.
针对落叶松集成材中的木材干燥问题,阐述太阳能-热泵联合干燥系统,并对木材干燥室进行了设计研究,实现对木材干燥中温度、湿度、空气流动、加热时间等影响木材干燥的关键因素进行全程监测和精确控制。 相似文献
17.
Measuring moisture content profiles in a board during drying: a polychromatic X-ray system interfaced with a vacuum/pressure laboratory kiln 总被引：1，自引：0，他引：1
A standard X-ray source and an energy-sensitive detector were placed on both sides of a wood dryer which operates over a wide
range of drying conditions. The spectrometric X-ray intensities transmitted through the wood sample were related to the mass
concentration of wood and water using a rigorous calculation needed in the case of a polychromatic X-ray beam. The source
and the detector are carried by a motion controller in order to scan the sample at different drying times and determine the
moisture content (MC) profile along the board thickness. Treatment on spectrometric data and the evolution of the MC profiles
in a Norway spruce board (Picea abies) are presented in this work. 相似文献
18.
19.
ZHANG Biguang YI Songlin CHANG Jianmin LI XianjunMaterial Science Technology School of Beijing Forestry University Beijing P.R.China 《中国林业科技(英文版)》2004,3(4):65-71
Using Masson pine as specimens, when drying mediums are overheated steam and hot-air respectively, preheating characteristics of wood under vacuum-floating pressure drying are discussed by measurement of internal temperature field and variation of moisture content during period of preheating. The relationship between drying medium conditions and drying rate of wood reveals that, firstly, compared with process of air-drying, time needed to be preheated under vacuum-floating decreased dramatically, meanwhile, the magnitude of condensation on the surface is relatively larger. Secondly, drying rate of wood under vacuum-floating pressure increases coupled with temperature of medium, reduction of absolute pressure, and raise of fluctuation rate of pressure. The sequence of factors contribution to drying rate is listed as following: temperature of medium (t) > fluctuation rate of pressure (f)> absolute pressure (p). 相似文献