共查询到20条相似文献，搜索用时 93 毫秒
1.
采用正交试验法探讨了各热压工艺因子对稻草刨花板薄木贴面的影响.试验结果表明:稻草刨花板表面饰贴薄木是切实可行的,进行0.2 mm厚水曲柳薄木贴面,在选用PVAC胶黏剂且涂胶量为100 g/m2的条件下,其较佳工艺参数分别为:热压压力为0.7 MPa、热压温度为100℃、热压时间为120 s;在选用GB-3胶黏剂且涂胶量为100 g/m2的条件下,其较佳工艺参数分别为:热压压力为0.8 MPa、热压温度为90℃、热压时间为180 s.进行0.6mm厚白橡薄木贴面,在选用PVAC胶黏剂且涂胶量为120g/m2的条件下,其较佳工艺参数分别为:热压压力0.8MPa、热压温度90℃、热压时间240 s;在选用GB-3胶黏剂且涂胶量为120g/m2的条件下,其较佳工艺参数分别为:热压压力0.7 MPa、热压温度90℃、热压时间180 s. 相似文献
2.
试制了"耐磨纸-意杨单板-HDF基材(12 mm厚)-平衡纸"4层结构强化木地板基材,研究了单板厚度(1.2,1.5,2.0 mm)、胶黏剂种类(聚氨酯,脲醛树脂)及涂布量(单面100,110,130,150,160 g/m2)对板材翘曲度、吸水厚度膨胀率、内结合强度及机加工性能的影响。结果表明:实木贴面复合木地板具备工艺技术可行性,产品的翘曲度随单板厚度和施胶量的提高而递增(最高可达约0.6%),采用聚氨酯胶黏剂时产品性能优于脲醛树脂胶合板材,但冷压周期偏长。推荐工艺条件为:单板1.2 mm,PU或UF胶黏剂均可,涂布量控制在100 g/m2左右。 相似文献
3.
通过对异氰酸酯(API)主剂进行改性,从而减少交联剂的用量,降低API胶黏剂的生产成本。将改性API胶黏剂用于秸秆板薄木贴面的试验表明,当主剂、交联剂、填料之比为100∶4∶30,热压温度为60~110℃时,秸秆板的贴面效果达到相关国标要求。 相似文献
4.
5.
6.
7.
三聚氰胺浸渍橡木薄单板贴面实木复合地板是参考三聚氰胺浸渍纸贴面生产工艺生产出的表面凹凸实木复合地板。使用三聚氰胺胶黏剂、固化剂、渗透剂、脱膜剂（配比为500：1：1：1）混合液浸渍橡木薄单板,然后在真空度为0.08 MPa时保压浸渍5 min,在大气条件下放置30 min,取出后再放入90℃鼓风干燥箱中干燥10 min。浸渍完成的橡木薄单板与基材经热压成型为表面凹凸的实木复合地板。考虑热压温度、热压压力、热压时间对其凹凸表面成型的影响,每个因素取4个水平,制定因素水平表,选择正交表进行试验。对试验结果进行浸渍剥离及表面纹理深度的测量分析,得到最优的热压工艺条件为温度150℃、压力1.2 MPa、时间70 s。三聚氰胺浸渍的橡木贴面复合地板表面纹理、色泽、手感都更加接近自然。 相似文献
8.
利用木粉和回收塑料制备的木塑复合材料具有良好的环保性,但制品表面装饰性差。采用砂光、紫外辐照、红外辐射3种方式处理木粉/高密度聚乙烯(WF/HDPE)复合材表面,以异氰酸酯或异氰酸酯交联聚醋酸乙烯酯(乳白胶)作为胶黏剂对WF/HDPE复合材进行单板贴面。通过表面胶合强度测试、表面接触角和粗糙度测试、扫描电子显微镜、傅里叶变换红外光谱和X射线扫描分析等手段研究了不同处理方式对表面胶合强度的影响。结果表明:320目砂纸砂光的表面胶合效果优于600目砂纸砂光的,可使WF/HDPE复合材表面具有适当粗糙度和极性。紫外辐照度1.00 W/m~2、辐照24 h和180℃-25 s红外辐射是比较好的处理条件,尽管没有进一步提高表面胶合强度,但红外辐射可减少砂光量。采用异氰酸酯交联乳白胶作为胶黏剂时,砂光处理的表面胶合强度为2.96 MPa,紫外辐照处理达到2.91 MPa,红外辐射处理达到2.87 MPa。3种方式处理的WF/HDPE复合材均能耐63℃水浸渍,传统人造板贴面技术完全有可能适用于木塑复合材料的表面装饰。 相似文献
9.
单板/高密度纤维板(HDF)复合木地板结合了实木地板和浸渍纸层压木质地板的优点,是地板产业发展的新方向之一。文中以12mm厚HDF为基材、复合意杨单板,试制了"耐磨纸-单板-HDF基材-平衡纸"四层结构地板用复合板材。研究了不同单板厚度、胶黏剂种类(聚氨酯-PU,脲醛树脂-UF)及涂布量对板材翘曲度、吸水厚度膨胀率、内结合强度及机加工性能的影响。结果表明:1)单板与HDF复合制造木地板是可行的;2)复合木地板的翘曲度随单板厚度和施胶量的提高而递增,最高可达约0.6%;3)贴面采用聚氨酯胶黏剂,产品性能优于脲醛树脂胶合板材,但冷压周期偏长。推荐工艺条件为:单板1.2mm,PU或UF胶黏剂均可,涂布量控制在100g/m~2左右。 相似文献
10.
11.
《Scandinavian Journal of Forest Research》2012,27(5):427-435
In Scandinavia, moose (Alces alces L.) sometimes cause severe browsing damage to economically-important pine. Moose-vehicle accidents have spurred construction of fences along roads, and these may interfere with moose migration between summer and winter ranges, or the road alone may be a barrier. If this happens and moose build up along roads, landowners may suffer economically. Therefore, this study investigated whether roads, fences or other factors influence the use of young pine stands by moose. Eighty stands along roads in northern Sweden were evaluated in which individually-browsed branches were counted on 9972 pines. Moose browsing was not significantly related to birch (Betula pendula Roth, B. pubescens Ehrh.) density, nor did it differ between pines (Pinus contorta Douglas or P. sylvestris L.). However, increased pine density, site productivity and proximity to a highway were associated with increased browsing. Further large-scale studies are needed to understand moose habitat selection and the effects of roads. 相似文献
12.
《Scandinavian Journal of Forest Research》2012,27(3):206-217
The root systems of 2-yr-old Picea glauca, Picea mariana and Pinus banksiana seedlings were submitted to various frost temperatures during an artificial frost to induce different levels of root damage. Frost-damaged and control seedlings were placed in a greenhouse under high and low soil moisture regimes. Seedling growth and physiology were evaluated periodically. Seedling survival was reduced when root damage reached levels of 60-80%. Root systems of all three species showed partial to total recovery by the end of the experiment. In general, root freezing damage caused reductions in seedling growth, with these reductions becoming less significant over time. Root damage had little to no effect on black spruce and jack pine seedling physiology, while white spruce CO 2 uptake decreased with increasing root damage. Shoot nitrogen content of all three species decreased slightly with increasing root damage. 相似文献
13.
Contour hedgerows of multipurpose tree species in the sloping tea lands of Sri Lanka are expected to reduce soil erosion and
also add significant amounts of plant nutrients to the soil via periodic prunings. The objective of this experiment was to characterize the biomass decomposition pattern and quantify the
amount of nutrients added through prunings of six tree species (Calliandra calothyrsus, Senna spectabilis, Euphatorium innulifolium, Flemingia congesta, Gliricidia sepium and Tithonia diversifolia) currently being used in hedgerows associated with tea. Withered leaf and stem prunings (50 g) were enclosed in 2-mm litter
bags, placed at 5-cm depth and retrieved after one, three, six, nine and 12 weeks. Loss of initial dry weight, N, P and K
was measured. Single exponential decay function adequately described both dry weight and nutrient loss. Tree species differed
significantly in their rate of breakdown with decomposition constants (k) varying from 0.0299 to 0.2006 week−1 for leaves and from 0.0225 to 0.0633 week−1 for stems. Gliricidia showed the highest k for leaves with the rest in the following descending order: Senna > Tithonia ≥ Euphatorium > Calliandra > Flemingia. A similar pattern was observed for loss of all nutrients with Calliandra and Flemingia always having lower k values than the rest. Although N immobilization was not observed, immobilization of P and K was observed
during the first week of incubation in some species, particularly in stem prunings. Annual biomass of prunings differed significantly
between tree species in the following descending order: Calliandra > Senna > Flemingia > Tithonia > Gliricidia > Euphatorium. Calliandra added the greatest amount of nutrients annually to the soil with Euphatorium adding the least. Calliandra prunings provided the annual total K requirement and 49% of the N requirement of mature tea. However, none of the species
provided more than 5% of the P requirement. It is concluded that among the tree species tested, Calliandra and Flemingia are the most suitable for contour hedgerows in tea plantations of this agroclimatic region because of their higher soil nutrient
enrichment capacity and slower decomposition rates which would minimize leaching losses.
This revised version was published online in June 2006 with corrections to the Cover Date. 相似文献
14.
《Scandinavian Journal of Forest Research》2012,27(2):118-130
The effects of seed weight and seed type on seedling growth of Pinus sylvestris (L.) were studied by seeding individually weighed orchard and stand seed in different mixtures under harsh (direct seeding in field) and optimal (seeding in nursery) conditions. In the nursery experiment an increase in the seed weight from 3 to 7 mg increased the seedling height by 10-27% and total weight by 27-113%, and decreased the height/diameter ratio by 5-6% after 2 yrs. With elimination of seed weight effects, orchard seedlings were 2% taller than stand seedlings in year 2. Without elimination of seed weight effects, orchard seedlings were 7-13% taller. In the field experiment an increase in the seed weight from 3 to 7 mg increased seedling height by 18-65%, stem volume by 81-274% and the number of top-buds by 23-34% in year 5. After elimination of seed weight effects, orchard seedlings were 7-13% taller than stand seedlings and without elimination of seed weight effects 20-21% taller after 5 yrs. Even after elimination of both seed weight and genetic effects orchard seedlings were 3-9% larger than stand seedlings in the field experiment. In conclusion, the influence of seed weight and seed type on growth traits and slenderness is highly significant and the influence seems to be greater in harsh conditions. 相似文献
15.
Astra Zaluma Lauma Bruna Darta Klavina Natalija Burnevica Kristine Kenigsvalde Andis Lazdins Talis Gaitnieks 《Forest Pathology》2019,49(6)
Heterobasidion parviporum and Heterobasidion annosum are widely distributed root‐rot fungi that infect conifers throughout Europe. Infection of conifer stumps by spores of these pathogens can be controlled by treating fresh stumps with a competing non‐pathogenic fungus, Phlebiopsis gigantea. In this study, growth of three Latvian strains of P. gigantea and the biological control agent ‘Rotstop’ strain was evaluated in stem pieces of Norway spruce, Scots pine, lodgepole pine, Douglas‐fir, Weymouth pine, Siberian larch and Sitka spruce. The growth rates of one H. parviporum and one H. annosum isolate were also measured in the same stem pieces. The growth rate of P. gigantea varied greatly in wood of different conifer species. It was higher in the three pine species, lower in Norway spruce and lowest in Sitka spruce and Siberian larch, and in Douglas‐fir, this fungus did not grow. The largest area of wood occupied by P. gigantea was in lodgepole pine. Growth of Latvian isolates of P. gigantea in the wood of Pinus and Picea species was comparable to that of the Rotstop isolate. Consequently, stump treatment with local P. gigantea isolates should be recommended. However, our results suggest that Douglas‐fir stump treatment against Heterobasidion by P. gigantea may be ineffective and other stump treatment methods should be considered. 相似文献
16.
《Scandinavian Journal of Forest Research》2012,27(1):53-61
This study investigated the stand structure in pine, spruce and deciduous forests in the border district of Finland and Russia. A total of 46 mature forest stands was selected as pairs, the members of each pair being as similar as possible with respect to their forest site type, age, moisture and topography. The stands were then compared between the two countries by means of basal areas and number of stems. The proportions of dominating tree species were 2-12% lower, and correspondingly the proportions of secondary tree species higher, in Russian forests. The density of the forest stock was also higher in each forest type in Russia. The forests in the two countries differed most radically in terms of the abundance of dead trees. The amount was two to four times higher in Russian deciduous and spruce forests, and in pine forests the difference was 10-fold. The stand structures indicated that Russian coniferous stands, in particular, were more heterogeneous than intensively managed pine and spruce stands in Finland. 相似文献
17.
《Scandinavian Journal of Forest Research》2012,27(1):15-27
The root collar diameter and the height:diameter ratio are of particular importance in container-grown seedlings where a high density in the containers may produce spindly seedlings. Temperature regimes and light quality are known to affect plant growth. The aim of this study was to identify responses in Picea abies (L.) Karst. seedlings grown with light providing different red:far-red ratios and under temperature regimes with alternating day (DT) and night temperature (NT) from negative (DT < NT) to positive (DT > NT) difference (DIF) between DT and NT. Experiments were conducted in controlled environment chambers and in a daylight phytotron. Only limited thermoperiodic responses appeared in P . abies seedlings with respect to seedling height and dry weight accumulation. The formation of terminal buds, however, was clearly delayed in seedlings grown at negative DIF. The results indicate a requirement for day extension light that is high in far-red, to prevent terminal bud formation under natural short-day conditions. An extended study should be conducted to clarify the minimum level of light intensity and the optimal light quality needed to prevent terminal bud formation under natural short-day conditions. 相似文献
18.
Steven Maranz Amadou Niang Antoine Kalinganire Djeneba Konaté Bocary Kaya 《Agroforestry Systems》2008,72(3):231-239
Baobab leaves form an important part of the local diet in Sahel countries and elsewhere in Africa. Existing leaf nutritional
data and agroforestry performance information are based solely on Adansonia digitata L., the baobab of continental Africa. The introduction potential of Adansonia species from the center of diversity in Madagascar and from Australia remains untapped. To assess this potential, the mineral
contents and B1 and B2 vitamin levels of dried baobab leaves were determined for five-year old trees of A. digitata, A. gibbosa (A. Cunn.) Guymer ex D. Baum, A. rubrostipa Jum. & H. Perrier (syn. A. fony Baill.), A. perrieri Capuron and A. za Baill. grown in an introduction trial in Mali. Nutritional data were evaluated against survival and vigor to identify promising
germplasm. Leaf vitamin and crude protein contents were highest in the Madagascar species, especially A. rubrostipa (B1 88 mg 100 g−1, B2 187 mg 100 g−1, protein 20.7% dry weight). However, the local species far outperformed the introductions in survival, tree height, basal
diameter and resistance to termites. We suggest grafting as a way of harnessing the vigor of well-adapted local baobab varieties
to the superior nutritional profiles of A. rubrostipa and others. Cross-species grafting tests in Adansonia were successful, thus creating new agroforestry possibilities with different scion/rootstock combinations. 相似文献
19.
《Wood material science & engineering》2013,8(2):76-84
Abstract Wood in general and wooden studs in particular are often distorted owing to uneven shrinkage during the drying process in the sawmill. Twist is often the most detrimental of all types of distortion, and it is caused by spiral grain in combination with variations in moisture content. For sawmills, the objective is to produce dried, straight boards, and one method of dealing with boards with excessive spiral grain is to sort them out and then dry them in a pretwisted position to obtain straight boards after drying. A model using the finite element (FE) method for the simulation of drying twist distortions was first calibrated against laboratory experiments in which boards were dried with and without restraints and pretwists. After the calibration, the FE results were compared with industrial test results for boards that were dried without restraints or with restraints with zero pretwist, i.e. straight restraints. The FE model used an elastic–ideally plastic material model to obtain permanent deformations. The calibration was to set the yield stresses so that there was a good match between FE results and results from the laboratory experiments. The comparison between the industrial test results and the FE results showed that the FE model is capable of realistic simulations of drying boards with and without restraints and presumably also pretwists. 相似文献
20.
本文分析了CAD在设计中引起的正面和负面影响,并进行了系统的阐述,从而使设计者在应用中能够保持客观的态度。 相似文献