共查询到18条相似文献，搜索用时 109 毫秒
1.
通过对核心区应用X形配筋增强的高强钢筋异形柱边节点和同等条件下未被增强的高强钢筋异形柱边节点进行拟静力试验研究,对比分析异形柱边节点的破坏特征、滞回曲线、承载能力、位移及延性、刚度退化、耗能能力等抗震性能指标。研究结果表明,配置HRB500高强钢筋异形柱边节点比配置600 MPa级的边节点承载能低,但滞回性能好,变形能力强,刚度退化推迟,耗能能力强;在核心区加入X形配筋,均可以改善高强钢筋异形柱边节点的破坏特征,使边节点抗剪能力、变形能力、耗能能力增强,刚度退化推迟,提高异形柱边节点抗震性能,配置HRB500高强钢筋的试件核心区应用X形配筋加强后抗震性能提高效果更好。 相似文献
2.
配置600 MPa级高强钢筋T形柱抗震性能试验研究 总被引：2，自引：0，他引：2
600 MPa级钢筋是一种新型高强度钢筋,为研究该钢筋应用于异形柱结构体系的可行性,对7根不同轴压比、体积配箍率和钢筋强度的混凝土T形柱试件进行低周往复荷载试验,分别对其承载力、位移、滞回曲线、骨架曲线、刚度退化和耗能性能进行研究,综合评估其抗震性能。研究结果表明：配置600 MPa级钢筋的混凝土T形柱具有良好的变形能力和承载能力,提高配箍率能有效提高试件的抗震性能,提高轴压比可以提高试件的承载力,但降低其变形能力。随着钢筋强度的提高,试件的承载力显著提高。 相似文献
3.
北京地区典型砖木结构农宅抗震加固性能研究 总被引：1，自引：0，他引：1
根据北京地区农村住宅调研结果,选取最典型的砖木(前檐砖柱支撑)结构,进行了加固前后的振动台试验。针对北京地区农村住宅砖木结构(砖柱支撑)未加固模型的振动台试验结果,提出了抗震加固措施,包括：加设钢筋混凝土窗框,增大前纵墙的抗侧刚度;采用水泥砂浆面层加固两面山墙、砖柱和窗下墙,提高墙体的承载和变形能力;加设钢圈梁,提高结构的整体牢固性。分析了模型加固前后振动台试验的损伤情况、频率和阻尼、加速度动力系数、位移和滞回曲线等结构动力特性参数。上述加固措施显著提高了此类砖木结构农宅的抗震能力,加固模型达到了“小震不坏、中震可修、大震不倒”的抗震设防目标。 相似文献
4.
Y形偏心支撑高强钢框架结构抗震性能 总被引：3，自引：1，他引：2
在Y形偏心支撑高强钢框架结构抗震性振动台试验的基础上,建立了试验试件的有限元模型,并验证了分析的正确性。设计了一个9层的Y形偏心支撑高强钢框架结构,以耗能梁段长度、耗能梁段腹板高厚比、高跨比为参数,对9层结构进行了非线性动力时程分析,研究了以上参数对结构抗震性能的影响。研究结果表明,改变耗能梁段长度、高跨比对结构层间侧移、耗能梁段性能、框架柱弯矩、耗能能力均有不同程度的影响,对框架柱轴力、基底剪力无显著影响;改变耗能梁段腹板高厚比对结构耗能能力有影响,对结构层间侧移、耗能梁段性能、框架柱受力、基底剪力无显著影响,并给出了相关设计建议。 相似文献
5.
为了研究CFRP加固冷弯薄壁C型钢长构件的承载能力,对腹板和翼缘均粘贴CFRP的试件进行了轴心受压加载试验。7根长度均为1 400 mm的试件,其中1根为未加固的控制试件,其余6根封闭缠绕外贴50 mm宽CFRP间距为50、100、150 mm 3种情况,层数为1层和2层。试验结果表明,在轴心荷载作用下的破坏模式为整体弯扭失稳,与控制试件相比,加固后试件的稳定极限承载力均有不同程度的提高;当CFRP间距与腹板高度的比值小于1时,加固效果较理想,且2层CFRP的加固效果好于1层。最后,采用有限元对模型进行数值模拟,对比试验数据和数值模拟结果,二者吻合较好。 相似文献
6.
为了防止联肢剪力墙中小跨高比连梁发生低延性剪切破坏,在单连梁中部设置一条通缝,形成开缝连梁改善其抗震性能。试验完成了3个小跨高比带板开缝连梁的低周反复加载,通过与其他配筋形式连梁对比,分析了开缝连梁的破坏形态、滞回特征、承载力退化、刚度退化、延性、耗能等一系列抗震性能。利用软件ABAQUS对试件滞回曲线的骨架曲线进行模拟,并将模拟结果和试验结果相对比。结果表明,小跨高比开缝连梁具有良好的承载能力及变形能力,施工较为方便且经济,能有效防止小跨高比连梁延性较差的剪切破坏,具有较好的抗震性能,可在实际工程中推广。 相似文献
7.
8.
采用非线性有限元分析程序ABAQUS对无粘结体外预应力CFRP片材加固简支钢筋混凝土T形梁后进行数值模拟,该模拟梁共4根分别为3根梁侧对称加固,1根为梁底加固均为四点波形齿锚固预应力CFRP带。对比结果显示,数据模拟与试验结果在构件屈服以前的承载力、变形以及极限承载力吻合程度较好,构件屈服以后的变形差别较大,因此,可在一定程度上有效替代试验分析方法。依据吻合程度最好的TL3参数设计了“两点锚固”和“四点锚固”的模型进行模拟分析。通过对锚固点数及加固量改变的对比分析可知,依据加固构件的弯矩改变各段加固量及布置锚固点数的方法既可以保证加固效果不降低,又可以节约CFRP材料。 相似文献
9.
钢管混凝土FRP混凝土（SCFC）组合柱是新近提出的一种新型组合柱形式。提出考虑外钢管与FRP的双重约束效果,采用双剪统一理论分析了SCFC组合柱外钢管、外层混凝土、FRP管以及内层混凝土的应力状态,根据静力平衡条件得到了SCFC组合柱的轴压承载力计算公式,其与试验结果能够较好吻合。分析了含钢率、FRP与钢的相对配置率、FRP径厚比以及FRP管直径对轴压承载力提高系数的影响,结果表明：随着含钢率的增加、FRP与钢的相对配置率的提高以及FRP径厚比的减小,SCFC组合柱轴压承载力提高系数都有一定程度提高;内FRP管直径与外钢管边长之比在0.65~0.75之间时,轴压承载力增益效果较好。 相似文献
10.
在梁侧或梁底用波形齿横向张拉CFRP片材并锚固的体外预应力加固混凝土结构技术,对3根完全相同的7 m跨T形截面梁进行加固：其中2根梁侧面加固;1根梁底部加固。试验表明：多点锚固体外无粘结CFRP预应力可以依据构件的弯矩来调整各段的加固量从而更有效的利用CFRP材料的高强性能;梁底与梁侧加固对提高构件的抗弯刚度差别不大;波形齿能彻底解决预应力CFRP片材的锚固问题。以该3根加固梁的试验结果为基础,提出了梁体极限状态下塑性绞区长度的体外无粘结预应力碳纤维加固受弯构件的抗弯承载力公式,以及考虑二次效应的有效惯性矩法的挠曲变形的计算公式,通过与试验值的对比分析可知,所提出的方法可供设计参考使用。 相似文献
11.
The mechnical characteristics of concrete is sensitive to the strain rate and it is crucial to consider the effect of load rates on the behavior of reinforced concrete (RC) structures subjected to dynamic loads such as severe earthquakes. In this study, numerical simulations on the dynamic behavior of typical RC column specimens under dynamic loadings with different load rates were performed. Concrete constitutive model considering the strain rate effects proposed by the CEB code was employed with a fiber model to characterize the nonlinear strain rate dependent behavior of RC columns. The developed dynamic fiber element model was validated by comparing the simulated results of four RC column specimens with the fast loading test results. Results show that the developed fiber element model can predict the behavior of RC columns with acceptable accuracy. After valiating the proposed fiber elemen model considering the strain rate effect, the load carrying capacity of different RC columns with various longitudinal reinforcement ratios and volumetric stirrup ratios were simulated. Results show that the trends of the influences of longitudinal reinforcement ratios and volumetric stirrup ratios on the load carrying capacity of the RC columns under dynamic loadings are different. 相似文献
12.
The accurate calculation of the deformation capacity of structures is very important to performance-based seismic design, which satisfies the explicit deformation demands. The method to evaluate drift capacity of fiber reinforced polymer (FRP) confined reinforced concrete circular columns under simulated seismic loading is focused. Firstly, the moment-curvature relationship of FRP confined sections of reinforced concrete (RC) circular columns is simulated by numerical analysis. It is found that the calculated ultimate curvature is significantly less than the test result, and the difference is controlled by the axial load ratio of the tested columns. According to the numerical and the test results, an equation is proposed to modify the calculated ultimate curvature. Based on this, the drift capacity can be predicted with the equivalent plastic hinge method. The calculated result agrees well with the test result when FRP amount is low, but it is significantly larger when FRP amount increases. Finally, the main parameters exerting influences on the drift capacity of the FRP-confined RC circular column are analyzed. 相似文献
13.
The experimental results of reinforced concrete sandwich beam column joints were studied intensively and finite element method simulation of such joints were performed for the sake of design method.Basic design criterion and computation contents were provided according to failure mode of specimens and other experimental results.And the limits of parameters were proposed based on the analysis of seismic behavior influence factors and comparison of traditional joints and sandwich joints.Hence, formulas of load resistant capacity were acquired by the results of load resistant capacity of specimens and nonlinear finite element method simulation.It is found that three measures should be taken for sandwich joints in order to reach demanded ductility and load resistant capability.Firstly, several parameters should be limited, including shear compression ratio, axial load ratio, ratio of beam concrete strength to column concrete strength, and minimal amount of transverse reinforcement of joint.Secondly, shear load resistant capacity and axial compressive load resistant capacity should be computed to ensure load resistant capability of joint, and essential strengthen measures could be applied if necessary.Thirdly, appropriate construction details should be taken to avoid reducing of beam bar anchorage capacity. 相似文献
14.
In order to investigate the flexural behavior of concrete beams reinforced with high strength hot rolled bars of fine grains, static bending test on four rectangle cross section HRBF400, HRBF500 RC beams was conducted. The results show that the experimental maximum crack width under short term load meets the requirement of current code while calculated value does not meet; mid span deflection of RC beams with HRBF400 under short term load still meets the requirement of current code while RC beams with HRBF500 does not meet. Bearing capacity calculating formula under conditions of crack/deflection control was proposed and conception of component's bearing capacity utilization coefficient (BCUC) was put forward. The influences of reinforcement strength, reinforcement diameter, concrete grade, reinforcement ratio, concrete cover thickness and high span ratio on BCUC were analyzed. Within the range of economic reinforcement ratio, ductility of HRBF RC beams meets the requirement. Energy dissipation capacity of HRBF RC beams is similar to that of normal RC beams at low reinforcement ratio but it decreases faster than normal RC beams with the increasing of reinforcement ratio. Energy dissipation capacity of HRBF RC beams is higher than that of normal RC concrete beams in elastic stage and it enhances with the increasing of reinforcement ratio. 相似文献
15.
Using the software, ABAQUS, accurate simulations of seismic behavior of 2 coupled wall specimens and 2 cantilever structure wall specimens using high performance fiber reinforced concrete (FRC) in plastic hinge under quasi static cyclic loading were carried out. The analysis model proves to be effective with the accordance between results of computation and experiment, then it can be used to analyze the seismic behavior of coupled wall system with FRC coupling beams. By using the verified numerical model, the ability of FRC coupling beams instead of RC coupling beams to provide acceptable performance was discussed. In addition, the impact of coupling ratio on seismic behavior of coupled walls was studied. The results show that coupled walls in which FRC coupling beams are used instead of traditional RC beams have good energy dissipation and ductility, and its initial stiffness is increased and stiffness degradation is slow. And as the coupling ratio of coupled wall structures increases, the stiffness and strength increase. But if the coupling ratio is too large, the ductility and energy dissipation capacity will be significantly reduced. 相似文献
16.
Earthquake induced dynamic axial force in reinforced concrete (RC) bridge bent columns will not only change the yield strength of the columns but also change their stiffness, which is seldom considered by the common lumped plasticity line model. Based on the fiber element model results that taking into account the influence of dynamic axial force on strength and stiffness simultaneously, the axial force stiffness interaction effect on the seismic responses of RC double column bridges was analyzed. The results show that, axial force stiffness interaction has a large effect on the seismic responses of the double column bridge in the elastic range, and it does not alter the ultimate capacity of the columns. Since the stiffness of the columns under compression and tension dynamic axial forces offset each other, the global displacement of bridge bent with equal columns is relatively unaffected by the axial force stiffness interaction, however, the differences of the column member forces are manifest. For the short column controls the global stiffness, the axial force stiffness interaction has significant influences on both the global displacement and member force responses. The influences become larger as the irregularity of the bridge bent increases, so the interaction between axial force and member stiffness should be sufficiently considered in seismic analyses. 相似文献
17.
With the flexibility-based fiber model,the seismic behaviors of RC structures with specially shaped columns,designed according to the current code,are analyzed under unidirectional rare earthquakes using nonlinear dynamic analysis method.The beam strength is calculated with or without consideration of the diaphragm and its reinforcement.The results are compared and the conclusion has been drawn that the bending capacity of beams would be increased due to the effect of diaphragm and its reinforcement,and which would change the failure mechanism of RC frames under rare earthquake,especially in high intensity areas.Therefore the influence of the diaphragm should be considered during the seismic design of the type of structure. 相似文献
18.
Inelastic Seismic Response of Reinforced Concrete Frame Structures Reinforced with HRB500 Steel Bars
To achieve sustainable development of construction industry, the application of HRB500 reinforcement with high strength and high ductility in RC structures is being promoted in civil and structural engineering in China. But few studies focus on seismic behaviors of RC structures reinforced with HRB500 bars. In this analysis, three RC frame structures on the Zone of Fortification Intensity 8 (0.3g) in China reinforced with HRB500, HRB400 and HRB335 bars respectively, are designed confirming to the latest draft of the revising Code for the Design of Concrete Structures. Then inelastic seismic response analyses of the three frames with multiple inputs of ground motions are conducted. The seismic response rules and seismic performances of the RC frame reinforced with HRB500 bars are compared with those frames reinforced with HRB400 and HRB335 bars. The analytical results indicate that under ground motions in rare earthquake level, the maximum displacements of the frame reinforced with HRB500 bars are roughly the same as those of the frames reinforced with HRB400 and HRB335 bars, while the rotation ductility demand of elements in the former structure is smaller than those of elements in the latter structures. It is also found that the frame reinforced with HRB500 bars develops a plastic energy dissipation mechanism that is dominated by beam hinges under major earthquake, and the maximum inter storey drift of the frame can satisfy the requirement in the Code for the RC Frame Structures. 相似文献