共查询到19条相似文献，搜索用时 531 毫秒
1.
为了探究ECC/高强钢筋混凝土叠合梁的正截面受弯特征，以及ECC层厚度对叠合梁整体受弯性能的影响，做了两组共5根梁试件的正截面受弯试验。发现与高强钢筋混凝土梁相比，叠合梁的承载力更高，相同荷载下的挠度值和最大裂缝宽度较小。在受弯全过程中其截面应变仍符合平截面假定，钢筋与ECC也可以实现协调变形，说明受拉区使用ECC可以使得高强钢筋的应力得到充分发挥。但ECC层厚度过大可能会使叠合梁发生脆性破坏。进一步地，在此研究的基础上，对已有ECC的本构模型进行简化，忽略其应力强化贡献，并运用叠加原理，提出一种用于计算ECC/钢筋混凝土叠合梁正截面受弯承载力的方法，将计算结果与试验结果及诸多文献结果进行比较，发现吻合度较高。 相似文献
2.
为研究T形板肋对预制带肋底板混凝土叠合板弯曲疲劳性能的影响,对3块T形肋底板叠合板和1块整浇板进行弯曲疲劳性能对比试验,主要考察T形板肋与疲劳荷载幅值对试件疲劳破坏形态及疲劳损伤程度的影响,得到了在不同疲劳循环加载次数下的跨中动位移、混凝土应变、预应力筋应变、残余变形等,分析了在不同疲劳循环加载次数下的刚度退化情况、荷载-应变分布规律、裂缝分布规律及剩余承载力等。研究结果表明,经历200万次疲劳循环加载后,T形肋底板叠合板无明显的刚度和强度退化,增设T形板肋的叠合板能达到与整浇板相同的弯曲疲劳性能;T形肋底板叠合板正截面弯曲疲劳强度计算可采用普通预应力混凝土受弯构件正截面疲劳应力验算的4个假定,最终以此建立了其正截面弯曲疲劳强度验算方法。 相似文献
3.
进行了大跨径预应力混凝土刚构桥腹板开裂机理研究,基于弹性力学平面问题分析方法,推导了集中荷载作用下的板件应力函数表达式,绘制了不同受压边长与集中荷载长度比（d/a）下的横向应力曲线,拟合了集中荷载作用下构件的横向应力求解函数,构造了混凝土刚构桥腹板在预应力集中荷载作用下等效压力矩形的选取方法,并基于平面应力的表达式提出了在三维情况下沿预应力轴线的横向应力计算方法。通过建立某预应力混凝土刚构桥0~3#段实体有限元模型,分析施工过程中刚构桥混凝土腹板在不同等级预应力作用下的开裂情况。结果显示：有限元裂缝模拟与实桥腹板开裂范围一致,有限元应力分析结果下限值与推导的横向应力求解函数计算结果接近,变化趋势一致,印证了横向应力函数求解方法的正确性。 相似文献
4.
早龄混凝土的拉伸、压缩徐变规律及其结构徐变应力计算方法是对早期裂缝进行有效预测并控制的关键。既有的徐变研究主要侧重于成熟混凝土,而早龄混凝土徐变相关的科学研究还有待进一步深入。对早龄混凝土的压缩和拉伸徐变研究成果、测试方法及其徐变应力计算方法进行了详细综述。研究表明：目前混凝土早龄期拉伸、压缩徐变试验测试尚无规范可循,相关试验数据较为缺乏;混凝土早龄期徐变预测模型基本未考虑其在低应力水平下的非线性性质;早龄混凝土结构非线性徐变应力理论分析方法亦不尽完善。基于系统试验研究和固化徐变理论建立混凝土非线性徐变理论模型,对早龄混凝土结构采用同时考虑受拉和受压不同应力松弛特性的非线性徐变应力理论计算方法,应可提高早龄结构的有限元仿真精度。 相似文献
5.
6.
针对竹筋混凝土结构存在的问题,提出了多种对竹筋的改性方法。在此基础上,对12根采用不同配筋和不同改性方法的受弯构件(11根竹筋混凝土梁和1根钢筋混凝土梁)进行了试验研究,分析了不同改性方法和不同配筋率竹筋混凝土受弯构件的力学性能、破坏形态及其影响因素。研究结果表明：竹筋能有效提高混凝土受弯构件的承载能力;经过适当方法改性后的竹筋能确保竹筋和混凝土之间的有效粘结,其正截面强度计算可以采用平截面假定;竹筋混凝土受弯构件的破坏均为脆性破坏,其破坏形态与其截面配筋率有关。 相似文献
7.
预应力CFRP布及预紧螺栓加固RC梁试验研究 总被引：1，自引：0，他引：1
为提高碳纤维布加固RC结构的效果及其可靠性,提出了预应力碳纤维布与预紧螺栓联合加固技术。结合在役RC梁的损伤特点及目前的RC梁加固方法,分别采用不同的碳纤维布加固技术对完整梁和破坏梁的抗弯性能进行了对比试验研究。针对目前碳纤维布张拉设备的缺陷,研发了便于现场应用的新型碳纤维布布张拉设备,分析了预应力大小对加固效果的影响。结果表明,预应力碳纤维布及预紧螺栓联合加固技术是一种更可靠的桥梁加固方法,不仅能够提高RC梁正截面的抗弯承载能力及正常使用阶段的截面刚度,而且螺栓预紧锚固碳纤维布能够很好地抑制其在混凝土表面的剥离,提高碳纤维布与混凝土表面之间粘结强度,对碳纤维布施加预应力能够充分发挥其高强性能,有效抑制混凝土裂缝开裂和开展。 相似文献
8.
采用简化的纤维增强混凝土应力应变关系,根据截面变形的平截面假定和截面力的平衡方程,推导出塑性铰区采用纤维增强混凝土柱在不同极限状态时的曲率。根据各极限状态点曲率,求得截面上各分布力,对截面形心轴取距,到塑性铰区采用FRC柱的开裂、屈服、峰值和极限点的弯矩表达式。与试验结果对比表明,计算值与试验值吻合较好。 相似文献
9.
研究了粉煤灰掺量、加载龄期和加载应力对粉煤灰混凝土早期变形及加载后强度变化的影响。研究结果表明：随着粉煤灰掺量增加,混凝土的变形量逐渐降低,当掺量为30%时,变形量减少了33.6%;随着加载龄期提前或加载应力增大,粉煤灰混凝土的早期变形量增大,其中,加载应力的影响尤其明显,60%加载应力（60%的标准养护条件下7 d轴心抗压强度）比20%加载应力下混凝土最终变形量增加了277.2%;混凝土初始加载时间提前或加载应力增大会导致加载后粉煤灰混凝土强度下降,加载应力比加载龄期对加载后粉煤灰混凝土强度的影响更明显。 相似文献
10.
为了得到钢构件高温下局部稳定设计方法,通过试验对建立的有限元模型进行了验证。采用验证后的有限元模型,分析了温度、板件宽厚比、初始几何缺陷、腹板和翼缘相互作用等因素对H形截面轴心受压钢构件局部屈曲应力的影响,提出了Q235钢和Q460钢H形截面轴心受压构件高温下的局部稳定承载力简化计算公式和高温下防止局部屈曲的翼缘宽厚比和腹板高厚比限值。研究表明：当板件宽厚比较小时,构件的局部屈曲应力随宽厚比的增大迅速减小,宽厚比较大时,构件屈曲应力降低不明显;初始几何缺陷对构件局部屈曲应力影响较小;高温下翼缘对腹板屈曲的约束作用比常温下明显;高温下防止局部屈曲的宽厚比限值与常温下宽厚比限值不同。 相似文献
11.
12.
Autogenous relative humidity (ARH) reduction and autogenous shrinkage (AS) due to self-desiccation are common phenomena in high performance or high-strength concrete, which are the main reasons resulting in cracking of concrete at early ages. In this paper, the effects of the ratio of water to cementitious material (w/cm), paste volume content and the combined addition of silica fume (SF) and ground blast furnace slag (GBFS) on ARH change and AS of concrete due to self-desiccation were studied, and their relationship was discussed. The results indicate that the w/cm is a main factor affecting ARH change and AS of concrete. With the reduction of w/cm, ARH change and AS of concrete increases. The combined addition of SF and GBFS also augments these properties at later ages. There is significant linear correlation between ARH change and AS of concrete with different w/cm, paste volume content and the combined addition of SF and GBFS. 相似文献
13.
According to the spatial features of environmental actions, on the basis of the spatial multi-scale model framework (including the global environment, regional environment, engineering environment, surface environment and internal environment of concrete) and the mathematic model for environmental actions, the spatial multi-scale relative humidity values for concrete structures were studied. That is, based on the influential factors of relative humidity on the different spatial scales, the relative humidity values in concrete were deduced by adjustment step by step from the values on the global environment to the regional environment, the engineering environment and the surface environment of concrete. It was found that using the superposition method of conventional statistic model and spatial residual error, the quantitive relationship of relative humidity values in the regional environmental scale and the engineering environmental scale can be established effectively. Moreover, the relative humidity values on the surface of concrete structural elements are related with the temperature values on the surface of concrete structural elements, and the difference of relative humidity values between the surface and the inner part of concrete should be considered in the durability assessment of concrete structures. 相似文献
14.
In this paper, the finite element method is used to analyze the behavior of the prestressed V-shape Slab Roof structure, especially the effect of temperature change on the stress of slab. The calculated results indicate that when the temperature changes, the tensile stress at the lower extreme fibers of the flange plate near rib exceeds the tensile strength of concrete subjected to the combined action of triaxial stresses and results in the longitudinal cracks of the flange plate. The deflection analysis is based on the mechanical model of the prestressed V shape slab with the longitudinal cracks. The calculated results are in general agreement with the field observations. 相似文献
15.
According to unsaturated soil basic theories, equilibrium moisture of clay subgrade is predicted based on the updated studies of soil suction and soil water characteristic curve. Also, the bilinearity constitutive experience model of resilient modulus of clay soil is presented by triaxial repeated loading tests in laboratory. Using above mentioned results, a prediction method of equivalent resilient modulus of clay subgrade is established by comprehensively considering subgrade moisture and stress condition. Then, based on the concrete engineering, the prediction function of equivalent resilient modulus of the clay subgrade is provided by taking ground water table and subgrade height as centers. Compared with the results of other traditional testing methods on the same test road, the new prediction method may be used in practice. The results provide new perspectives and standpoints to determine the equivalent resilient modulus mechanics features of clay subgrade structure from two aspects of equilibrium moisture and stress condition. 相似文献
16.
为了建立水稻不同区域、不同生育期的水稻稻纵卷叶螟预测模型,利用103个植保站2000-2014年稻纵卷叶螟虫情资料与气象资料,采用SPSS软件进行相关分析与主成分分析,在逐步回归的基础上建立水稻稻纵卷叶螟不同区域、不同生育期的发生发展气象等级与迁入气象等级预测模型。结果表明：以华南早稻为例,影响早稻移栽分蘖期发生发展的关键因子包括3月下旬累积降水量、4月上旬平均气温、4月下旬平均气温、5月上旬平均气温以及5月上旬最高气温＞30℃天数;迁飞的关键因子包括4月平均相对湿度、3月下旬平均气温、3月下旬平均相对湿度以及4月上旬平均日照时数。通过2000—2012年数据回代检验发现,不同水稻种植区移栽分蘖期和抽穗开花期发生发展气象等级平均准确率能达到80%以上,迁入气象等级在85%以上。通过2013—2014年外推预报时,发生发展气象等级平均准确率在80%以上,迁入气象等级在78%以上;当预测站点样本数较少时,预报的准确率普遍下降,西南一季稻下降明显。预测模型可从气象角度对中国水稻稻纵卷叶螟发生发展和迁入进行预测。 相似文献
17.
Study on mechanical behaviors of interface with cemented soil slurry between gravel and concrete by simple shear tests 
下载免费PDF全文
下载免费PDF全文 The mechanical behaviors of the interface between coarse-grained soil and concrete are investigated by simple shear tests under conditions of cemented soil slurry (clay mixed with cement grout). The results show that the relation curve between shear stress and shear strain appears stress-strain softening and shear dilatation is significant. The point of peak strength and the position when the shear dilatation occurs are related to normal stress. In addition, shear dilatation occurs before the shear stress reaches peak value. In shear failure state, with the same height, the shear displacement increases as the normal stress increases. While with the same normal stress and at the same height, the shear displacement increases as the concrete content increases. A particle flow model of simple shear test between interface between coarse-grained soil and concrete is constructed by PFC (particle flow code). The disturbed height of the sample and the main influence factors are determined by analyzing the laws of particle motion at different heights inside the sample. The PFC results show disturbed height of the sample is related to maximum particle diameter of the soil, normal stress and roughness of the interface (with or without slurry) etc. In terms of the coarse-grained soil, the shear displacement is significant in the area which is close to the interface and about 3-4 times of the maximum particle diameter, and informed the obvious shear band. Further, the thickness of the interface can be regarded as the value. 相似文献
18.
The corrosion rate of steel in concrete is highly dependent on the heterogeneous structure of the concrete and the environmental exposure conditions. Temperature and relative humidity are two important environmental factors that simultaneously influence the corrosion process and cannot be separated or isolated from each other. The interaction of temperature and relative humidity for characterizing the corrosion rate has been sufficiently studied. The resules show that the higher the temperature is, the greater the relative humidity is when rebar corrosion rate reaches the max, and as to different relative humidity, the increasing extent of rebar corrosion rate with rise in temperature is different. 相似文献
19.
粉煤灰对高强混凝土收缩徐变的影响直接关系到结构长期性能的合理确定。制作粉煤灰掺量分别为0、12%和24%的100 mm×100 mm×400 mm的C50混凝土棱柱体试件,在试验室条件下进行收缩及不同加载龄期的徐变试验,研究了粉煤灰对高强混凝土收缩徐变的影响。根据试验结果评估了目前常用的4种相关规范公式对高强混凝土收缩徐变的适用性,并引入粉煤灰影响系数以综合反映粉煤灰掺量和加载龄期对高强混凝土收缩徐变的影响,根据试验结果和现有研究成果提出了其修正模型。分析结果表明,JTG D 62和GL 2000推荐的收缩徐变预测模式与基准试件实测结果较为吻合,验证结论亦说明所引入的粉煤灰影响系数可应用于掺粉煤灰高强混凝土的收缩徐变预测。 相似文献