首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 31 毫秒
1.
Particleboards of different densities (0.6, 0.7 and 0.8 g/cm3) and thicknesses (10 and 20 mm) were manufactured from low-moisture particles using an air-injection press. The effects of the air injection on preventing blowout of the boards of different densities and thicknesses were investigated by artificially creating blowout-prone conditions using metal frames. The effects of the air-injection pressure on the board performance were also investigated. 10-mm-thick boards of 0.8 g/cm3 pressed at 170 °C blew out when air was not injected, but were successfully manufactured by injecting air. 10-mm-thick boards at 150 °C showed constant internal bond (IB), regardless of density, but at 170 °C, IB was higher in boards of higher densities. This was likely due to accelerated hardening of the urea–formaldehyde resin at 170 than 150 °C. At both pressing temperatures, low air-injection pressure did not cause blowout and a reduction in board performance. Air injection also prevented the blowout of thick boards of 20 mm and enabled successful manufacture, showing its effectiveness. The IB of the 20-mm-thick board manufactured using the air-injection press exceeded that of 20-mm-thick board manufactured using an ordinary hot press.  相似文献   

2.
A hot press was used to manufacture particleboards (H boards). A radio-frequency hot press (for RH boards) and an air-injection radio-frequency hot press (for ARH board) were also used, and the effects of air injection on preventing blowout and board properties were analyzed. The thicknesses and densities of manufactured boards were 10 and 30 mm, and 0.6, 0.7, and 0.8 g/cm3, respectively. The investigation ascertained the effects of air injection in preventing blowout when a radio-frequency hot press is used. The increasing order of temperature was ARH board > RH board > H board during the final pressing stage. For the 30-mm-thick boards, the temperature of H board increased to 100 °C and remained constant at 100 °C even when the pressing time was extended. The temperature of the RH board increased to 100 °C more quickly than in the case of the H board and remained constant at 110–118 °C. The temperature of the ARH board increased linearly to 130–142 °C. For both the 10- and 30-mm-thick boards, the internal bond strength of the RH board was almost the same as that of the ARH board at densities of 0.6 and 0.7 g/cm3. In contrast, the internal bond strength of the RH board was lower than that of the ARH board at a density of 0.8 g/cm3. For the 10-mm-thick boards, the thickness swelling in the RH board was almost the same as that in the ARH board irrespective of the density. However, for the 30-mm-thick boards, the thickness swelling in the RH board was higher than that in the ARH board. The low plasticization of particles due to air injection presumably results in a high degree of thickness swelling.  相似文献   

3.
Blowouts of particleboards were artificially induced by increasing the vapor pressure inside the boards. Isocyanate resin bonded boards were manufactured from high-moisture particles, and the blowouts and board properties were analyzed. Boards with a high resin content of 5 % showed high bonding strength and did not blow out when pressed at 190 °C, but blew out at a raised temperature of 210 °C to increase vapor pressure inside the boards, thereby showing that blowout occurred when vapor pressure inside the boards exceeded the bonding strength of isocyanate resin. Boards with a low resin content of 2.5 % had low bonding strength and blew out when manufactured without air injection, but were successfully manufactured with air injection that prevents blowouts. However, the injection of high-pressure air reduced the strength properties of the board and increased the coefficient of variation, likely due to the discharge of isocyanate resin from the boards. Therefore, very small local blowouts occurred inside the boards, which lowered the strength properties of some specimens and led to a large coefficient of variation. When the pressure of injected air was lowered, the strength properties increased and the coefficient of variation decreased. This was possibly because the low-pressure air allowed isocyanate resin to remain in the boards, resulting in virtually no parts showing very low-strength properties.  相似文献   

4.
An air-injection press, which has holes punched in the heating plates, injects high-pressure air through the holes of one plate into particleboards and discharges the air and vapor through the other plate during press heating. The press can manufacture particleboards from high-moisture particles by preventing blowouts of the boards. In this study, the effects of pressing temperature were investigated by pressing boards at 190, 210, and 230°C. The internal bond strength increased from 0.43 to 0.60?MPa by raising the temperature from 190 to 210°C, but did not increase further when the temperature was raised to 230°C. Raising the temperature from 190 to 210°C also helped improve the thickness swelling. No relationship was found between the modulus of rupture and pressing temperature.  相似文献   

5.
The effectiveness of air injection for preventing the blowout of particleboards manufactured using a radio-frequency hot press was investigated by evaluating the board properties under artificially created conditions that were conducive to blowout. For evaluation, 10-mm-thick boards with densities of 0.7 and 0.8 g/cm3 and 20-mm-thick boards with a density of 0.7 g/cm3 were manufactured. Pressing times for the 10-mm-thick boards were 2, 4, 6, and 8 min, and those for the 20-mm-thick boards were 4, 6, 8, and 10 min. Without air injection, blowout occurred in all manufactured boards. With air injection, however, blowout did not occur in the 10-mm-thick boards with a density of 0.7 g/cm3. Moreover, air injection prevented blowout even when the board density and board thickness were increased to 0.8 g/cm3 (for 10-mm-thick boards) and 20 mm (the density was kept at 0.7 g/cm3), respectively. Air-injection radio-frequency pressing reduced the pressing time from 4 to 2 min for 10-mm-thick boards, and from 6 to 4 min for 20-mm-thick boards. Moreover, this reduction in the pressing time was achieved without a large reduction in the internal bond strength of the boards.  相似文献   

6.
An air-injection press was developed to prevent particleboard from blowing out during the manufacturing process. The air-injection press, which has holes punched in the heating plates, injects high-pressure air into the board through the holes of one plate and releases the air through the holes of the other plate. The high-pressure air forces out vapor trapped within the board, thus preventing blowout. The newly developed press reduced the pressing time required for manufacturing board from high-moisture-content particles. However, the manufactured boards exhibited mechanical properties and dimensional stability inferior to conventionally manufactured boards.  相似文献   

7.
An air-injection press, which has holes punched in the heating plates, injects high-pressure air through the holes of one plate into boards during press heating. The air-injection press can manufacture boards from high-moisture-content particles by controlling blowouts of the boards. In this study, boards were manufactured from particles that had a moisture content of 25% by using the air-injection press, which reduced the required pressing time. Boards manufactured by injecting air through holes of 5 mm in diameter were of poor quality with a low internal bond strength of only 0.31 MPa. When the hole diameter was reduced to 1 mm, the internal bond strength increased to 0.44 MPa. A high air-injection pressure of 0.55 MPa also resulted in improved board properties over those for boards manufactured at lower pressures. This was probably because a large amount of binder was released from boards through the 5-mm holes, together with water vapor, during air injection; the small-diameter holes reduced the release of binder, resulting in better board properties.  相似文献   

8.
Particleboards with thickness of 10 mm and densities of 0.6, 0.7 and 0.8 g/cm3 were manufactured from high-moisture particles using urea–formaldehyde resin and the effectiveness of air injection was examined. The temperature in the 0.6 and 0.7 g/cm3 boards was lower with air injection than without during the initial to middle stages of pressing, while the temperature in the 0.8 g/cm3 board remained lower with air injection than without throughout the entire pressing process. Air injection reduced the pressing time required to manufacture the 0.6 and 0.7 g/cm3 boards and also increased the internal bond strength of boards of all densities. In the 0.6 and 0.7 g/cm3 boards, air injection reduced the modulus of rupture (MOR), while in the 0.8 g/cm3 boards, the MOR was similar between those manufactured by injecting and not injecting air. Air injection was also found to be effective for boards of high densities. The effectiveness of the air injection on thick boards was investigated by manufacturing 20-mm-thick boards of 0.7 g/cm3. Without air injection, it was not possible to manufacture the 20-mm-thick boards, even by extended hot pressing, but air injection allowed the boards to be manufactured by pressing for 16 min. Air injection was also shown to be effective for manufacturing thick boards.  相似文献   

9.
This paper describes the features of binderless particleboard manufactured from sugarcane bagasse, under a high pressing temperature of 200–280 °C. Mechanical properties [i.e., modulus of rupture (MOR) and elasticity (MOE) in dry and wet conditions, internal bonding strength (IB)] and dimensional stability [i.e., thickness swelling (TS)] of the board were evaluated to investigate the effect of high pressing temperature. Recycled chip binderless particleboards were manufactured under the same conditions for comparison, and particleboards bonded with polymeric methylene diphenyl diisocyanate (PMDI) resin were manufactured as reference material. The target density was 0.8 g/cm3 for all of the boards. The results showed that the mechanical properties and dimensional stability of both types of binderless boards were improved by increasing the pressing temperature. Bagasse showed better performance than that of recycled chip as a raw material in all evaluations. Bagasse binderless particleboard manufactured at 260 °C had an MOE value of 3.5 GPa, which was equivalent to the PMDI particleboard, and a lower TS value of 3.7 % than that of PMDI particleboard. The MOR retention ratio under the dry and wet conditions was 87.0 %, while the ratio for the PMDI particleboard was only 54.6 %. The obtained results showed the possibility of manufacturing high-durability binderless particleboard, with good dimensional stability and water resistance, which previously were points of weakness for binderless boards. Manufacturing binderless boards under high temperature was effective even when using particles with poor contact area, and it was possible to express acceptable properties to allow the manufacture of particleboards. Further chemical analysis indicated a contribution of a saccharide in the bagasse to the improvement of the board properties.  相似文献   

10.
An air-injection press, which has holes punched in the heating plates, injects high-pressure air through the holes of one plate into particleboard and discharges the air through the other plate during press heating. The press can manufacture particleboard from high-moisture particles by controlling blowout of the boards. In this study, the optimum diameter and spacing of the air-injection holes and the effects of pre- and post-pressing were investigated. An optimum hole diameter was not found for the modulus of rupture and thickness swelling for a spacing of either 25 or 50 mm. In terms of internal bond strength, the optimum diameter of the holes arranged at a spacing of 25 mm was 1 mm, but the internal bond strength was not changed by the diameter of holes spaced 50 mm apart. Air injection under all hole conditions reduced the formaldehyde emission from the board. Pre-pressing was tested for further increase in the modulus of rupture and internal bond strength, but was found to have no effect. More efficient use of the air-injection press was achieved by injecting air from the early stages of pressing.  相似文献   

11.
Abstract

Five-ply self-bonded boards were obtained by pressing beech veneers parallel to the grain without additional adhesives, steam or pre-treatment. Fifteen different combinations of pressing parameters were tested, including temperature (200°C, 225°C and 250°C), pressure (4, 5 and 6 MPa) and pressing time (240, 300 and 360 seconds). Due to severe pressing conditions, the new product showed a higher density and different properties compared to a conventionally glued laminated wooden board. The self-bonding quality was assessed through dry shear strength tests, through a three-point bending test and a water-soaking test at 20°C. The dimensions in the cross section of the boards were measured after soaking in water. Results show that the choice of pressing parameters affects all the mechanical and physical properties tested. A statistical analysis revealed that the pressing temperature is the most influential parameter. Boards pressed at 200°C delaminated rapidly in water, whereas boards pressed at 225°C delaminated only at core-positioned layers after 48 hours and boards pressed at 250°C did not delaminate at all in water. Compared to panels pressed at lower temperatures, boards pressed at 250°C had the highest density, a higher shear and bending strength and a lower water absorption.  相似文献   

12.
Authors established a new manufacturing technology for crack-free carbonized boards by pressing and carbonizing the medium-density fiberboard. Industrialization of new functional carbon materials was performed by investigating the fundamental properties of the carbonized boards. To be used as a construction material, the carbonized board needs to satisfy the fire performance regulation. In this study, the carbonized boards were manufactured from medium-density fiberboard (c-MDF) at different temperatures and then fire performance including flame retardancy and smoke toxicity was analyzed using a cone calorimeter and noxious gas analyzer. The results show that as the carbonization temperature increases, weight loss ratio decreases and flame retardancy increases. In the c-MDF at 800 and 1000 °C, no external damage was observed after combustion. These c-MDFs satisfy the total heat release (standard below 8 MJ/m2) and heat release rate (standard below 200 kW/m2) regulations according to the Building Standard Law of Korea and Japan. In addition, the c-MDFs showed the lower total smoke release (TSR, 0.213 m2/m2) than that of virgin MDF (94.281 m2/m2). The c-MDF at 800 and 1000 °C were, therefore, classified as a class III flame retardancy material and can be used as indoor finishing material.  相似文献   

13.
In this study, the effects of acetylation and press time on the heat transfer from the surface to the core on the particleboard mat, springback, internal bonding, modulus of elasticity, and modulus of rupture were determined. Particles were soaked in the acetic anhydride for 24 h and heated in an oven at 120°C for 40 minutes, 3 h and 6 h to achieve three weight gain levels of 8%, 12%, and 17%, respectively. Acetylated and control boards were produced with 10% melamine urea formaldehyde (regarding the particles dry weight) and pressed for 5, 6, and 7 minutes. During the pressing process, the heat transfer to the core layer of the mat was measured by thermocouple made of Cr-Ni wires. It was found that the increase of acetylation level leads to significant reduction in heat transfer during manufacture process and develops springback which in turn, results in density loss. Findings indicated that these defects were correlated with the press time and compensated by the press time prolongation. Strength loss of the acetylated boards was due to debonding of the constituent that compensated somewhat with increasing press time.  相似文献   

14.
To improve the properties of particleboard, boards were produced using a sealed press. With the sealed press, boards were processed under high-temperature and high-pressure steam. This increased the saturation temperature, causing a dramatic rise in temperature inside the board, faster curing of the binder, and a shorter pressing time. The boards were bonded with urea formaldehyde resin, melamine urea formaldehyde resin, or poly(methylene diphenyl diisocyanate) (PMDI). The sealed press improved the internal bond strength and thickness swelling of boards regardless of the binder used during the reduced pressing time. The increased bonding strength improved the board properties, allowing PMDI with a lower resin content to be used for bonding the boards.  相似文献   

15.
The purposes of this study were to examine the use of furniture mill residues containing high-density raw materials in particleboard production and to evaluate the effect of mixing several types of furnish on board performance. Wood wastes collected from the furniture industry in Japan containing matoa (Pometia pinnata), Douglas-fir (Pseudotsuga menziesii), and sugi (Cryptomeria japonica) with different particle shapes were prepared as raw materials for use in the manufacture of experimental particleboards. Seven board types and three mixed boards were manufactured with three replications. Methylene diphenyl diisocyanate (MDI) resin was applied at 6 % content in mat preparation. The pressing conditions were temperature of 180 °C, initial pressure of 3 MPa, and pressing time of 5 min. The target density was 0.72 g/cm³. This study showed that matoa particleboard had properties suitable for use in interior applications, although its properties were considered inferior compared with other particleboards. Improvement of matoa particleboard could be achieved by mixing with higher quality wood particles such as those from sugi or Douglas-fir. The furnish type used in this study affected board performance. All residues from furniture mills have the potential to be used for particleboard production, even when they contain different furnish types and wood species.  相似文献   

16.
Binderless boards are composite boards that rely on self-bonding mechanisms for inter-fibre bonding. Quercus acutissima and Quercus serrata logs degraded by Lentinula edodes (shiitake fungi) were used in this study to investigate whether physical and chemical changes induced by shiitake fungi can enhance board mechanical properties. Binderless boards were manufactured with 0.8 g/cm3 target density, 220 °C pressing temperature, 5 MPa pressure, and pressing duration of 10 min. Boards made from logs degraded for ≥?26 months were stronger than control boards and met modulus of rupture (MOR) and internal bonding (IB) requirements for fibreboards. Chemical composition and particle size distribution of the wood powder used to make the boards were determined to elucidate the drivers of board mechanical properties. The proportion of small particles (<?150 µm) showed a strong positive correlation with MOR for both species and hot water extractives showed a strong positive correlation with IB for Q. acutissima boards. Introduction of shiitake fungi pre-treatment to the production process may enhance the mechanical strength of binderless boards.  相似文献   

17.
Abstract

The purpose of this study was to evaluate the dimensional stability and strength properties of compressed laminated veneer lumber (LVL) produced using a closed hot pressing system. LVL specimens were produced with varying number of veneers using either diphenylmethane diisocyanate (MDI) or a water-soluble phenol formaldehyde (PF) resin at varying temperatures (160–200°C), pressures (0.5–3 MPa) and hot-pressing times (2–16 min). Results show that the heating process decreases the recovery of compressive deformation in the veneers when subjected to cyclic moisture and heat conditions. Thickness swelling was approximately 5% after a drying, wetting and boiling cyclic test for LVL using the MDI resin and hot pressed at 200°C for 8 min. Modulus of elasticity and rupture increased for samples produced in both an open press and the closed press with an increase in the number of veneers and density, as did the absorbed energy in impact bending.  相似文献   

18.
Binderless particleboards were manufactured from sugi (Cryptomeria japonica D. Don) heartwood and sapwood by hot-pressing (pressure: 5 MPa; temperatures: 180°, 200°, and 220°C; times: 10, 20, and 30 min), and the board properties [internal bonding (IB), thickness swelling (TS), water absorption (WA)] were investigated to evaluate the self-bonding ability. The IB, TS, and WA of the boards from sugi heartwood were better than those of the boards from sugi sapwood at any hot-pressing condition. Therefore, it was suggested that the self-bonding ability of sugi heartwood was superior to that of sugi sapwood. Then, sugi heartwood and sapwood powder with grain size 10 βm were used as a binder for plywoods. Four kinds of plywood were manufactured from the combination of powder and veneer, both of which were prepared from sugi heartwood and sapwood under the same hot-pressing conditions as the binderless particleboard, and the adhesive shear strength and wood failure of the plywood were investigated. As a result, the plywood composed of sugi heartwood veneer met the second grade of JAS for plywood, when either powder was used as a binder, when they were pressed at 200°C for 20–30 min and 220°C for 10 min.  相似文献   

19.
An outdoor exposure test was conducted on kenaf core binderless boards (pressing temperatures 200°, 180°, and 160°C; pressing pressure 3.0 MPa, time 10 min, target board thickness 5 mm, target board density 0.8 g/cm3) to estimate their bond durability. Modulus of rupture (MOR), modulus of elasticity (MOE), internal bonding strength (IB), thickness change, weight loss, Fourier transform infrared (FTIR) spectra, and color difference (ΔE*) by the CIE L*a*b* system were measured at various outdoor exposure periods up to 19 months. These values were then compared with those of a commercial medium-density fiberboard (MDF; melamine-urea-formaldehyde resin; thickness 9.0 mm, density 0.75 g/cm3). Generally, dimensional stability and the retention ratios of MOR, MOE, and IB after the outdoor exposure test increased with increased pressing temperature of binderless boards. The MOR retention ratio of the kenaf core binderless boards with a pressing temperature of 200°C was 59.5% after 12 months of outdoor exposure, which was slightly lower than that of the MDF (75.6% after 11 months of outdoor exposure). Despite this, the bond durability of the kenaf core binderless boards should be viewed as favorable, especially when considering the fact that the retention ratio of 59.5% was achieved without binder and without obvious element loss. Part of this report was presented at the International Symposium on Wood Science and Technology, IAWPS2005, November 27-30, 2005, Yokohama, Japan  相似文献   

20.
In this study, molding moso bamboo strips to a curved shape using hot-press molding operation was explored. Bamboo strips with different thickness and moisture content (MC) were subjected to press molding under 120–210 °C for different time. Changes in the chemical components of bamboo were analyzed by Fourier-transform infrared spectroscopy (FTIR). Effect of MC on thermal mechanical behavior of bamboo was investigated using dynamic mechanical analysis (DMA). Results showed that the influencing degree of four variables on compression and recovery ratios decreased as: temperature?>?time?>?thickness?>?MC. Compression ratio increased and recovery ratio decreased dramatically when pressing temperature exceeded 180 °C. FTIR analysis indicated that polysaccharide (especially hemicelluloses) underwent a progressive thermal degradation during compression at 180 and 210 °C for 40 min, whereas relative content of lignin increased. DMA results showed that bamboo samples with a higher MC had a lower storage modulus value, confirmed water had a plasticizing effect. The loss factor of bamboo with higher MC (12 and 16%) exhibited two major transitions centred around 100 °C (α1) and 50 °C (α2), respectively. The temperature of these α transitions kept almost unchanged as moisture level increased from 12 to 16%. These findings provide fundamental information for the future preparation of curved bamboo as profiled components in engineered products.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号