首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 62 毫秒
1.
Cross-linked hydroxypropylmethylcellulose (HPMC) cast films with citric acid as polycarboxylic cross-linker were elaborated to study the effect of cross-linking level on various properties. Increased amounts of cross-linking agent were not connected to statistically different tensile strength and Young's modulus. Whatever the cross-linking level of the film was, the ultimate elongation parameter decreased by approximately 60% compared to the HMPC control film. Moisture sorption isotherms and water contact angle meter showed that the effect of cross-linking degree tends to reduce the hygroscopic and hydrophilic characteristics of films. In addition, to control bacteria growth on food surfaces, the antimicrobial activity of both 98% cross-linked HPMC-nisin and control HPMC-nisin films was tested on Micrococcus luteus. Despite the incorporation of a significant content of nisin, cross-linked HPMC-nisin films were completely inactive on the microbial strain compared to the HPMC-nisin control films. Cross-linking conditions likely either denatured the nisin or irreversibly bound nisin to the cross-linked HPMC. However, nisin adsorbed into films made from previously cross-linked HPMC maintained its activity.  相似文献   

2.
The purpose of this study was to evaluate the characteristics of a chitosan film cross-linked by a naturally occurring compound, aglycone geniposidic acid (aGSA). This newly developed aGSA-cross-linked chitosan film may be used as an edible film. The chitosan film without cross-linking (fresh) and the glutaraldehyde-cross-linked chitosan film were used as controls. The characteristics of test chitosan films evaluated were their degree of cross-linking, swelling ratio, mechanical properties, water vapor permeability, antimicrobial capability, cytotoxicity, and enzymatic degradability. It was found that cross-linking of chitosan films by aGSA (at a concentration up to 0.8 mM) significantly increased its ultimate tensile strength but reduced its strain at fracture and swelling ratio. There was no significant difference in the antimicrobial capability between the cross-linked chitosan films and their fresh counterpart. However, the aGSA-cross-linked chitosan film had a lower cytotoxicity, a slower degradation rate, and a relatively lower water vapor permeability as compared to the glutaraldehyde-cross-linked film. These results suggested that the aGSA-cross-linked chitosan film may be a promising material as an edible film.  相似文献   

3.
Properties of zein films coated with drying oils   总被引：1，自引：0，他引：1  
Zein films prepared by resin were coated with either flax oil or tung oil and cured by UV- or gamma-radiation. Coated zein films were then evaluated for tensile and water barrier properties. Film microstructure was examined by transmitted light microscope. Tensile strength, elongation, and toughness of oil-coated samples increased substantially with respect to uncoated films. Flax oil coated samples showed an increase in elongation of 300%. It was suggested that oil coatings fill in pinholes and cracks existing in zein films, affecting their mechanical properties. Water vapor permeability also decreased statistically for coated film (except for tung oil coated-UV treated films), suggesting water vapor transfer was controlled by film hydrophobicity and microstructure. Moreover, the liquid water transmission rate of coated films was at least 10 times slower than for control films. Examination of film microstructure revealed that flax oil coatings had uniform coverage and smooth finish, which explained their high elongation, low water vapor permeability. Tung oil coatings cured under UV light showed patterns of intertwined dark and light regions, which may be caused by cross-linking and drying at different times. The oriented structures were found when tung oil coatings were cured by gamma-radiation.  相似文献   

4.
Cast zein films are brittle at room conditions, so plasticizers are added to make them more flexible. The tensile properties of these films are known to be affected by the relative humidity (RH) of the ambient air. However, little is known about how the plasticizers are affected by RH. Cast zein films were plasticized with either glycerol (GLY), triethylene glycol (TEG), dibutyl tartrate (DBT), levulinic acid (LA), polyethylene glycol 300 (PEG), or oleic acid (OA). Mechanical properties and moisture content (MC) of the films were measured after one week of storage at 3, 20, 50, 70, 81, and 93% RH. The relative humidity of the films' storage had a great effect on the films' tensile properties. All the films' tensile strength and Young's modulus values decreased as RH increased. Films containing DBT, TEG, LA, or PEG showed an increase in the percent elongation with increasing RH. Films containing GLY, OA, or no plasticizer did not show any increase in percent elongation as RH increased. The changes seen in tensile properties with increasing RH are because of zein's hygroscopic nature. The absorbed water will further plasticize the zein. The type of plasticizer used determined the extent of the changes seen in the tensile properties of films stored at different RH values. Depending on the plasticizers used in the film, there were large differences in the amount of water absorbed. Films increasingly absorbed water depending on the plasticizer they contained in the order GLY > TEG > LA > PEG > NONE > DBT > OA. Films containing hygroscopic plasticizers like TEG absorbed too much water at high RH and became weak, but they absorbed enough water at lower RH values to not be brittle. While films containing the more hydrophobic plasticizer DBT were brittle at intermediate RH values, they had good mechanical properties at high RH values.  相似文献   

5.
Water sorption, water vapor permeability, and tensile properties were evaluated for zein films plasticized with oleic acid. The effect of relative humidity on water vapor permeability and tensile properties of films was investigated. Samples were produced by two different methods: casting from a zein solution and stretching from a zein-fatty acid resin. Films were also coated with linseed oil. Results indicated that preparation method affected water sorption and permeability of zein films. Resin films showed lower water sorption than cast films, especially at high Aw values. Water vapor permeability was also lower for resin films. Coating with linseed oil further improved water vapor barrier ability of resin films. Permeability was affected by environmental relative humidity; higher relative humidity resulted in increased permeability. Environmental relative humidity also affected tensile properties of resin films. Toughness and elongation were improved when relative humidity increased from 50 to 85% rh. Tensile strength showed a maximum at 75% rh. Coating improved elongation and toughness of films. Maximum elongation and toughness were observed for coated samples at 85% rh. Zein resin films showed good tensile and water barrier properties that were maintained through environmental humidity levels from 50 to 98% rh.  相似文献   

6.
This study focuses on the effect exerted by interchain disulfide bonds on the functional properties of films made from gliadins when cross-linked with cysteine. Gliadins were extracted from commercial wheat gluten with 70% aqueous ethanol, and cysteine was added to the film-forming solution to promote cross-linking between protein chains. The formation of interchain disulfide bonds was assessed by SDS-PAGE analysis. Gliadin films treated with cysteine maintain their integrity in water and become less extensible while their tensile strength increases as a consequence of the development of a more rigid network. The glass transition temperature of cross-linked films shifts to slightly higher values. The plasticizing effects of glycerol and moisture are also demonstrated. The mechanical behavior of cysteine-cross-linked gliadin films was compared to that of polymeric glutenins. Cross-linked gliadins displayed tensile strength values similar to those of glutenin films but achieved slightly lower elongation values. Cysteine-cross-linked gliadin films present the advantage that they are ethanol soluble, facilitating film fabrication or their application as a coating for food or for any other film or surface.  相似文献   

7.
徐慧  陈野 《农业工程学报》2015,31(8):272-276
传统浇铸法制备的玉米醇溶蛋白薄膜表面粗糙,机械性质及耐水性较差。为了改善玉米醇溶蛋白理化性质,在传统浇铸法膜制备过程中引入平行匀强电场(1~5 A/m2)处理蛋白成膜液。经过电场处理后,玉米醇溶蛋白表面光滑、形状完整。试验结果表明:电场处理可改善薄膜力学性质、表面疏水性、水蒸气透过率等性质;随着电流密度的增大,薄膜拉伸强度、断裂伸长率、水蒸气透过率、吸水率以及表面接触角呈现规律性增加或者减小;电场处理下薄膜热特性改变,与未处理组相比变性温度略有提高,最大增幅为19.5℃。当电流密度为4 A/m2时,薄膜理化性质较佳:拉伸强度、断裂伸长率分别为73.09 MPa和9.68%,吸水率降低至14.87%,水蒸气透过率为2.55×10-8 g·m/(m2·h·Pa),静态接触角为62.18°,变性温度提高到118.39℃,热稳定性提高,薄膜表面光滑。电场可诱导成膜液中分子有序性排列,提高薄膜均一性;通过调节电流密度可得到具有一定力学强度和亲/疏水性的薄膜。试验结果为制备具有特定功能性的纯玉米醇溶蛋白薄膜材料提供了理论依据。  相似文献   

8.
Cinnamaldehyde is a naturally occurring α,β-unsaturated aldehyde. Its potential as a natural cross-linker to improve the physical performance of cast wheat gliadin films was evaluated. The cross-linking reaction was found to be dependent on the pH of the reaction medium, with pH 2 as the optimum. The water resistance (weight loss after immersion), mechanical properties (Young's modulus, tensile strength and elongation at break), thermal properties (T(g) and decomposition behavior), optical properties and morphology of films were evaluated. Cross-linked films showed high transparency, maintained their integrity after immersion, and displayed significant improvements in tensile strength and Young's modulus without impairment of their elongation properties. These effects, which were proportional to the amount of cinnamaldehyde added, highlight the possible formation of intermolecular covalent bonds between "monomeric" gliadins, leading to a polymerized network. Thus, this treatment could provide a new alternative to the toxic cross-linkers commonly employed and so extend the use of gliadin films.  相似文献   

9.
To prepare composite films from biopolymers with anti-listerial activity and moisture barrier properties, the antimicrobial efficiency of chitosan-hydroxy propyl methyl cellulose (HPMC) films, chitosan-HPMC films associated with lipid, and chitosan-HPMC films chemically modified by cross-linking were evaluated. In addition, the physicochemical properties of composite films were evaluated to determine their potential for food applications. The incorporation of stearic acid into the composite chitosan-HPMC film formulation decreased water sensitivity such as initial solubility in water and water drop angle. Thus, cross-linking of composite chitosan-HPMC, using citric acid as the cross-linking agent, led to a 40% reduction in solubility in water. The water vapor transfer rate of HPMC film, approximately 270 g x m(-2) x day(-1) x atm(-1), was improved by incorporating chitosan and was further reduced 40% by the addition of stearic acid and/or cross-linking. Anti-listerial activity of films was determined on solid medium by a numeration technique. Chitosan-HPMC-based films, with and without stearic acid, inhibited the growth of Listeria monocytogenes completely. On the other hand, a loss of antimicrobial activity after chemical cross-linking modification was observed. FTIR and 13C NMR analyses were then conducted in order to study a potential chemical modification of biopolymers such as a chemical reaction with the amino group of chitosan. To complete the study, the mechanical properties of composite films were determined from tensile strength assays.  相似文献   

10.
The mechanical properties of cross-linked edible films based on calcium caseinate and two type of whey proteins (commercial and isolate) were investigated. Cross-linking of the proteins was carried out using thermal and radiative treatments. Size-exclusion chromatography performed on the cross-linked proteins showed that gamma-irradiation increased the molecular weight of calcium caseinate, while it changed little for the whey proteins. However, heating of the whey protein solution induced cross-linking. For both cross-linked proteins, the molecular weight distribution was >/=2 x 10(3) kDa. Combined thermal and radiative treatments were applied to protein formulations with various ratios of calcium caseinate and whey proteins. Whey protein isolate could replace up to 50% of calcium caseinate without decreasing the puncture strength of the films. Films based on commercial whey protein and calcium caseinate were weaker than those containing whey protein isolate. Electron microscopy showed that the mechanical characteristics of these films are closely related to their microstructures.  相似文献   

11.
The strength of films extruded from powder blends of corn zein or corn gluten meal (CGM) with low‐density polyethylene was investigated. Tensile strength, percent elongation at break, and elastic modulus of the extruded films were measured. The tensile strength decreased from 13 MPa to ≈10.5 MPa with zein addition, while CGM addition resulted in tensile strength of ≈6 MPa. The higher the level of biological material (CGM or zein) in the films the lower the tensile properties. Films containing CGM exhibited significantly lower tensile properties than those containing zein. Extrusion processing of biological films is a step toward commercial viability.  相似文献   

12.
Corn gluten meal (CGM) was studied to investigate the effect plasticizers and water have on its melt processing, and how this melting affects its mechanical properties. GCM containing varying amounts of water were mixed with 23% (w/w) plasticizers; (glycerol, triethylene glycol (TEG), dibutyl tartrate, and octanoic acid in a Haake bowl mixer at 80°C. The amount of water in the CGM affected the amount of torque produced in the Haake mixer. This increase in torque was correlated with how well the CGM melted in the mixer. SEM images of CGM melted in the mixer showed a more uniform homogenous structure when processed at its optimum moisture content. Glycerol, TEG, and dibutyl tartrate produced the greatest torque when the CGM contained <1% water. Octanoic acid produced the greatest torque when the CGM was processed at 8% moisture. CGM plasticized with TEG and octanoic acid were mixed at either their optimum moisture or at 9.6% moisture and then compression molded into tensile bars. The tensile strengths of the bars that were mixed at their optimum moisture content were significantly greater than the bars mixed at 9.6% moisture. The tensile properties of the CGM samples were affected by relative humidity (rh). The tensile strength decreased and elongation increased as relative humidity increased. CGM plasticized with TEG saw a greater changes in its tensile properties due to relative humidity than did octanoic acid plasticized CGM.  相似文献   

13.
Free‐standing films were prepared from zein formulations containing 30, 40, 50, 60, 70, and 80% oleic acid (OA). Zein/OA formulations were also used as coating films for rodent diet bars. Water vapor permeability (WVP) of films and moisture loss rate (MLR) of coated rodent diet bars were measured at 4 and 25°C. Temperature affected the water barrier properties of films and coatings. At 4°C, WVP of films decreased with OA concentration while it increased at 25°C. WVP behavior was attributed to oleic acid phase changes due to temperature. At 4°C, OA is a crystalline solid that limits water diffusion through the films. At 25°C, liquid OA increased the system free volume and allowed for water diffusion. The effect was more pronounced the higher the OA concentration in films. Differential scanning calorimetry (DSC) of zein/OA films showed endothermic peaks at 12–18°C, confirming the melting of OA in that temperature range. MLR of coated rodent diet bars was also affected by temperature and OA concentration in coating formulations. In this case, formulations containing 40, 50, and 60% OA were better moisture barriers than coatings with higher OA content at both 4 and 25°C. Moisture losses were reduced at 4°C due to OA solidification.  相似文献   

14.
Fractions from the sorghum dry milling industry, including bran, are a potential source of kafirin. Free‐standing plasticized cast films were prepared from defatted kafirin preparations from red and white sorghum flour and bran fractions, and from commercial zein. All the kafirin preparations were able to form films. However, there were differences in film thickness, clarity, flexibility, surface texture, odor, and color between the different kafirin films. Bran kafirin films were highly colored, less flexible with a less smooth surface texture compared with films from flour, probably due to higher levels of contaminants in the bran kafirins. The strong color of the bran films could limit their use in certain coating applications. The kafirin films had much higher tensile strength and lower extensibility than zein film, probably because of the presence of β‐ and γ‐kafirins in the kafirin, giving high levels of disulfide cross‐linking in the kafirin films. The kafirin films had poorer water barrier properties than zein film, possibly due to greater thickness or to poorer flexibility, which may have caused microcracks.  相似文献   

15.
Zein protein is a major coproduct of biofuel from corn. To reduce the brittleness of zein films, a new type of zein-based biomaterial, was synthesized by chemical modification of zein with lauryl chloride through an acylation reaction. The final products were confirmed by (1)H NMR, FT-IR analysis, and SDS-PAGE. Thermal analysis detected no microphase separation in the synthesized polymer matrix. As the content of lauryl moiety increased, the glass transition temperatures of modified zein decreased by as large as 25.8 °C due to the plasticization effect of the lauryl moiety. In addition, mechanical and surface properties of cast films from acylated zein were also investigated. The elongation at break of modified zein sheet was increased by about 7-fold at the high modification level with some loss of mechanical strength. The surfaces of modified zein films were as uniform as unmodified zein film but more hydrophobic, further suggesting that no microphase separation happened during the film formation process. This work indicated the potential of these new biomaterials in the development of biodegradable food packaging materials and delivery systems.  相似文献   

16.
It has been a long-lasting challenge to prepare highly ordered biopolymer nanocomposites to optimize or tune the desired mechanical and barrier properties of the nanocomposite film. In this study, we developed a simple and cost-effective method to synthesize highly ordered zein nanocomposites. The method involved the synthesis of magnetic iron oxide (Fe(3)O(4)) nanofiller and the preparation of a highly ordered structure by in situ nanofiller reorientation under an external magnetic field. The successful preparation of Fe(3)O(4) magnetic nanoplatelets together with exfoliated and highly ordered zein resin nanocomposites was confirmed by scanning electron microscopy, X-ray diffraction, and a vibrating sample magnetometer. As a result, in comparison to zein resin film, the exfoliated zein nanocomposites (Fe-Zein) showed dramatic improvement on mechanical and barrier properties. The tensile strength, elongation, and Young's modulus of Fe-Zein were increased by 218, 48, and 264%, respectively, while the water vapor and oxygen permeability decreased by 68 and 29%. More importantly, the highly ordered zein nanocomposites (Fe-Zein-Mag) showed additional improvement on the mechanical and gas barrier properties. In comparison to Fe-Zein, the tensile strength and elongation of Fe-Zein-Mag were increased by 10 and 48%, respectively, and a 30% decrease in Young's Modulus was observed, indicating the Fe-Zein-Mag film was more elastic. Besides, the water vapor and oxygen permeability of Fe-Zein-Mag were also decreased by an additional 48 and 17%, respectively.  相似文献   

17.
Interest in biodegradable materials for packaging and agricultural uses has grown in recent years. Plant proteins have been proposed as inexpensive, renewable, and abundant feedstock. Corn zein was investigated based on value-added considerations and on the unique thermoplastic and hydrophobic properties of zein. Films prepared from zein are known to be tough and resistant, but also hard and brittle, thus requiring the addition of plasticizers to improve flexibility. The objectives of this research were to study the tensile properties, water absorption, and microstructure of zein sheets plasticized with palmitic and stearic acids. Both palmitic and stearic acids showed similar effects as plasticizers of zein. Tensile strength of zein sheets increased with the addition of low levels of plasticizers. However, beyond a critical point, tensile strength decreased with further addition of fatty acids. Water absorption decreased continuously with increasing fatty acid content. Kinetic parameters indicated fatty acids decreased water absorption by decreasing the saturation level of zein sheets. Coating zein with flax oil decreased the rate of water absorption by sealing off surface pores. Scanning electron micrographs of zein sheets showed the development of layered structures as fatty acid content increased. Zein-fatty acid layers were believed to be responsible for the increased tensile strength of plasticized zein sheets and to have contributed to increased resistance to water absorption.  相似文献   

18.
Composite films were prepared from pectin and fish skin gelatin (FSG) or pectin and soybean flour protein (SFP). The inclusion of protein promoted molecular interactions, resulting in a well-organized homogeneous structure, as revealed by scanning electron microscopy and fracture-acoustic emission analysis. The resultant composite films showed an increase in stiffness and strength and a decrease in water solubility and water vapor transmission rate, in comparison with films cast from pectin alone. The composite films inherited the elastic nature of proteins, thus being more flexible than the pure pectin films. Treating the composite films with glutaraldehyde/methanol induced chemical cross-linking with the proteins and reduced the interstitial spaces among the macromolecules and, consequently, improved their mechanical properties and water resistance. Treating the protein-free pectin films with glutaraldehyde/methanol also improved the Young's modulus and tensile strength, but showed little effect on the water resistance, because the treatment caused only dehydration of the pectin films and the dehydration is reversible. The composite films were biodegradable and possessed moderate mechanical properties and a low water vapor transmission rate. Therefore, the films are considered to have potential applications as packaging or coating materials for food or drug industries.  相似文献   

19.
In this study, antimicrobial films were developed against Campylobacter jejuni by incorporation of gallic acid (GA) into zein-based films. The zein and zein-wax composite films containing GA between 2.5 and 10 mg/cm(2) were effective on different C. jejuni strains in a concentration-dependent manner. Zein and zein-wax composite films showed different release profiles in distilled water but quite similar release profiles at solid agar medium. Depending on incorporated GA concentration, 60-80% of GA released from the films, while the remaining GA was bound or trapped by film matrix. The GA at 2.5 and 5 mg/cm(2) caused a considerable increase in elongation (57-280%) of all zein films and eliminated their classical flexibility problems. The zein-wax composite films were less flexible than zein films, but the films showed similar tensile strengths and Young's modulus. Scanning electron microscopy indicated different morphologies of zein and zein-wax composite films. This study clearly showed the good potential of zein and GA to develop flexible antimicrobial films against C. jejuni.  相似文献   

20.
Improvement in the water stability and other related functional properties of thin (<50 μm) kafirin protein films was investigated. Thin conventional kafirin films and kafirin microparticle films were prepared by casting in acetic acid solution. Thin kafirin films cast from microparticles were more stable in water than conventional cast kafirin films. Treatment of kafirin microparticles with heat and transglutaminase resulted in slightly thicker films with reduced tensile strength. In contrast, glutaraldehyde treatment resulted in up to a 43% increase in film tensile strength. The films prepared from microparticles treated with glutaraldehyde were quite stable in ambient temperature water, despite the loss of plasticizer. This was probably due to the formation of covalent cross-linking between free amino groups of the kafirin polypeptides and carbonyl groups of the aldehyde. Thus, such thin glutaraldehyde-treated kafirin microparticle films appear to have good potential for use as biomaterials in aqueous applications.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号