共查询到20条相似文献，搜索用时 15 毫秒
1.
2.
With regard to the long span continuous composite beams, the early composite shear stud strength at the joint surface between the steel girder and concrete slab at different concrete ages should be considered while the concrete slabs are casted by phases in construction stage. In this study, the push-out test of stud shear connectors were conduced at different concrete ages. Meanwhile, the change law of the ultimate shear strength, ultimate slip deformation, design shear strength, and shear stiffness of the stud shear connectors with concrete ages were analyzed, and the corresponding time-dependent calculation equations were presented. The results include that the main failure modes of stud shear connectors are the concrete slab splitting failure before 3-days concrete age. The load-slip laws of stud shear connectors at different concrete ages are basically the same, however, the shear strength and stiffness all increase with the concrete ages prolonging, and the increase degree is faster at early ages, but slower at later ages, which indicates that the early composite shear stud strength at the joint surface of composite beams should not be neglected. 相似文献
3.
A new steel concrete composite structure was proposed which composed of steel box beam, PC beam and PBH Shear connection. Bend test was carried out for the performance study of deformation and stress. It was found that Material advantages of steel and concrete were fully used and crack of concrete and local instability of steel box were avoided. And the deformation between steel box and concrete can be smoothed with PBH shear connection. As the calculated values showed good agreements with the test results, the proposed formulas can be reliably applied to the practice analysis. With the different parameters analysis, mechanic performance of the composite was obtained. 相似文献
4.
在高层建筑结构设计中,由于上部荷载较大或梁的跨度较大,使得梁的截面高度较高,通常会影响建筑的有效层高和建筑的总体高度。为了减小各层梁板结构高度,有效增大各层净高,提出了一种钢箱梁嵌入现浇板的新型组合梁板连接方式。针对这种新型连接方式,对6个钢箱梁混凝土板组合连接区域进行了板承受支座负弯矩的单调加载试验,对比分析了采用钢箱梁嵌入混凝土板组合楼盖与传统栓钉连接组合楼盖中板抵抗支座负弯矩的性能差异;并利用ABAQUS对试件进行了有限元分析。试验与有限元分析结果表明：采用钢箱梁嵌入板连接组合方式,其混凝土板抵抗支座负弯矩的能力与传统连接方式板抵抗支座负弯矩能力没有明显差异。 相似文献
5.
Spatial Calculation Methods of Three Main Trusses Continuous Plate truss Composite Bridge 总被引：2，自引：0，他引：2
According to the structural features of three main trusses continuous plate truss composite bridge, two composite beam methods are presented by constructing the displacement mode of composite beam elements and deriving the stiffness matrix of composite beam elements. The characteristic of composite beam method one is that the bridge slab is taken as the top flange of the chord of main truss and combined with the chord of main truss to form a steel concrete composite beam; the characteristic of composite beam method two is that the bridge slab is taken as the top flange of longitudinal and traverse beam and form a steel concrete composite beam with longitudinal and traverse beams. And as for the conventional plate beam composite method, the slab is characterized by forming bridge slab system with continuous isotropic sheets and longitudinal and traverse beams to bear load. Also, the comparison between theoretical results and experimental ones verifies the effectiveness of the above three methods. 相似文献
6.
高温下钢管约束型钢混凝土柱的受力性能 总被引：1，自引：0，他引：1
火灾下无防火保护的结构构件温度会迅速上升,从而造成钢材和混凝土的强度明显下降。为了研究火灾下钢管约束型钢混凝土柱的受力性能,考虑火灾下钢管约束型钢混凝土柱的不均匀温度分布及温度对材料力学性能的影响,提出了火灾下受轴心荷载作用的钢管约束型钢混凝土柱承载力的计算方法。利用有限元软件ABAQUS对提出的计算方法进行了验证,结果吻合较好。进而采用该计算方法对影响高温下承载力的参数进行了分析,研究表明：随着构件截面尺寸的增加以及混凝土强度和钢材强度的提高,构件的承载力逐渐增加,而钢管壁厚的改变对承载力并无太大影响。利用有限元软件ABAQUS分析了荷载比、构件尺寸、钢管壁厚等因素对构件耐火极限的影响,发现耐火极限随着荷载比和钢管壁厚的增加而减小,随着构件尺寸的增加而增大。 相似文献
7.
２４ｍ跨双曲薄壳板是集数学模型，高强钢材，高标号砼为一体的空间薄壳壁结构，是板架合一的新型屋面构件。近年来在粮食行业的库房建设中开始使用。实践证明，这种新型屋面构件具有结构合理，技术经济指标先进等特点，使用效果良好。 相似文献
8.
GFRP抗浮锚杆在基础底板中的锚固性能现场试验研究 总被引：2，自引：0，他引：2
通过现场拉拔破坏性试验,测得不同直径的GFRP抗浮锚杆在基础底板内的极限承载力和滑移量,并与实际工程中不同形式的钢筋抗浮锚杆作比较,分析其承载性能和粘结特性。研究表明,在相同的混凝土强度与养护条件下,相同直径的GFRP抗浮锚杆的极限承载力、平均粘结强度与钢筋抗浮锚杆相比较高,且GFRP抗浮锚杆的变形能够满足实际工程需求,充分验证了GFRP材料用作抗浮锚杆的先进性与合理性。基于试验结果与理论分析,给出了GFRP抗浮锚杆与基础底板的最佳锚固面积,并提出了计算公式。 相似文献
9.
为研究T形板肋对预制带肋底板混凝土叠合板弯曲疲劳性能的影响,对3块T形肋底板叠合板和1块整浇板进行弯曲疲劳性能对比试验,主要考察T形板肋与疲劳荷载幅值对试件疲劳破坏形态及疲劳损伤程度的影响,得到了在不同疲劳循环加载次数下的跨中动位移、混凝土应变、预应力筋应变、残余变形等,分析了在不同疲劳循环加载次数下的刚度退化情况、荷载-应变分布规律、裂缝分布规律及剩余承载力等。研究结果表明,经历200万次疲劳循环加载后,T形肋底板叠合板无明显的刚度和强度退化,增设T形板肋的叠合板能达到与整浇板相同的弯曲疲劳性能;T形肋底板叠合板正截面弯曲疲劳强度计算可采用普通预应力混凝土受弯构件正截面疲劳应力验算的4个假定,最终以此建立了其正截面弯曲疲劳强度验算方法。 相似文献
10.
为准确分析单箱双室组合箱梁的剪力滞效应,考虑钢混凝土的界面滑移效应和钢腹板的剪切变形,针对顶底板和翼板定义不同的剪力滞翘曲位移函数,基于能量变分法推导出单箱双室组合箱梁剪滞效应的控制微分方程及其闭合解。以单箱双室组合箱梁算例为基础,利用该方法分析其剪力滞效应的规律,结果表明：在同时考虑滑移和剪切变形时,组合箱梁的挠度比初等梁理论解大,且其挠度随界面滑移刚度的增大而减小;组合箱梁在均布荷载作用下,滑移量与荷载值近似成正比关系;在相同条件下,钢箱梁底板的剪力滞效应较混凝土顶板显著。 相似文献
11.
Some conclusions were drawn from two groups of in-site tests on concrete pile composite foundations. In the tests, it was found that the pressure under the rigid loading slab is different, in which the pressure under the center of the slab is the less and under the edge of the slab is the biggest. The pile-soil stress ratio is not a constant; it increases with the adding of the load. Most of the pile-soil ratio vary from 9 to 13 in these tests and the load that the piles share can be more than seventy percent of the whole load. It was proved that the bearing capacity of the concrete pile composite foundation is high with a little settlement, so it will be used more and more in the future. 相似文献
12.
Preparation technology of fiber toughened self compacting high strength concrete was tested by measuring influence of water/binder ratio, sand percentage, and steel fiber content on spread, T500 time , U shape value, and L shape value of fresh concrete. Mechanical properties were analyzed in case of different water/binder ratio, sand percentage, and steel fiber content. The test results show that suitable W/B and sand percentage were necessary to satisfy self compacting performance of the fresh concrete. With the increase of steel fiber content, the compressive strength and flexural strength were improved while workability of fresh concrete was cut down. Steel fiber toughened self compacting high strength concrete was prepared successfully with a strength grade of CF90 and a flexural strength of more than 11.0 MPa. 相似文献
13.
14.
通过对内贴应变片钢筋的直接拔出试验,分析冻融作用下粉煤灰掺量对钢筋与粉煤灰混凝土间粘结性能的影响,得出冻融循环作用对钢筋与粉煤灰混凝土之间粘结性能的影响规律。试验结果表明：钢筋与粉煤灰混凝土的粘结强度随粉煤灰掺量的增加而降低;当粉煤灰掺量一定时,随着冻融循环次数的增加,混凝土强度有所下降,钢筋与粉煤灰混凝土间极限粘结强度降低;当粉煤灰掺量较大,达到40%时,随冻融次数的增加,钢筋粉煤灰混凝土试件极限粘结强度的下降幅度明显减缓,极限粘结强度对应的滑移量增大。表明掺入较多粉煤灰可使试件的冻融损伤现象得到缓解,冻融环境下钢筋混凝土的粘结性能得到提高。 相似文献
15.
为了探究ECC/高强钢筋混凝土叠合梁的正截面受弯特征,以及ECC层厚度对叠合梁整体受弯性能的影响,做了两组共5根梁试件的正截面受弯试验。发现与高强钢筋混凝土梁相比,叠合梁的承载力更高,相同荷载下的挠度值和最大裂缝宽度较小。在受弯全过程中其截面应变仍符合平截面假定,钢筋与ECC也可以实现协调变形,说明受拉区使用ECC可以使得高强钢筋的应力得到充分发挥。但ECC层厚度过大可能会使叠合梁发生脆性破坏。进一步地,在此研究的基础上,对已有ECC的本构模型进行简化,忽略其应力强化贡献,并运用叠加原理,提出一种用于计算ECC/钢筋混凝土叠合梁正截面受弯承载力的方法,将计算结果与试验结果及诸多文献结果进行比较,发现吻合度较高。 相似文献
16.
WANG Yin-hui~ 《保鲜与加工》2004,(1):62-67
Different creep coefficients of concrete layers in composite beam will cause redistribution of stress and additional stress in section. Based on the concept of strain compatibility approach, in this paper,the authors deduced a differential equation of the additional inner forces resulted from creep. Thereafter, the authors proposed an equation to calculate stress redistribution of steel and concrete composite beam, concrete composite beam and concrete strengthening member. At last, the formulas of additional stress of the section were proposed. 相似文献
17.
In the study on the CRCP+AC composite pavement, the form and distribution pattern of cracks are two important factors influencing the performance and the lifetime of the pavement. The concrete damaged plasticity material model incorporated in the general purpose finite element software named ABAUQS was adopted to describe the mechanical characteristics of the CRC slab. Combining with the temperature field database drawn from the three-dimensional transient heat transfer analysis, the structural damage under the condition of temperature changing is analyzed. The structural damage evolution and the crack behavior of the CRC slab subjected to the thermal-mechanical coupling condition are further analyzed, which suggests that the role of the asphalt concrete surface is not confined only to the scope of improving the performance of the road, its capacity for improving the stress state of CRCP slab is worthwhile to be affirmed. And the reasonable thickness of AC layer should be designed in consideration of the thermal contraction and damage properties of the CRC slab comprehensively. 相似文献
18.
为了研究钢箱-砼组合结构中PBH剪力键在反复荷载作用下的疲劳性能,设计制作了PBH剪力键试验模型,进行了24万次疲劳推出试验。在疲劳破坏形态和试验滑移及应变数据分析的基础上,利用数值工具开展肋板开孔孔径、穿入钢筋直径、混凝土强度3个参数的PBH剪力键疲劳寿命影响因素分析。研究表明：PBH剪力键的疲劳破坏形态与静载破坏相似,表观表现为混凝土面多处斜向劈裂裂缝、内部榫孔混凝土压碎、穿入钢筋局部屈服;疲劳破坏演化过程分为疲劳损伤开始、发展、破坏3个阶段,其中疲劳发展阶段占整个疲劳阶段的91.7%,结构刚度在疲劳损伤开始和发展阶段退化较慢,在疲劳破坏阶段退化较快;肋板开孔孔径、穿入钢筋直径、混凝土强度3个参数对PBH剪力键疲劳寿命影响均有明显影响,其中穿入钢筋直径对疲劳寿命的影响尤为突出。 相似文献
19.
Theoretical and Experimental Analysis of Bending Behavior of Composite Beam with Notched Web 总被引：2，自引：0，他引：2
A new kind of steel-concrete composite beam with notched web is proposed, and the bend and shear behaviors of this composite beam are investigated. First of all, the constitution, bearing characteristics and merits of the steel-concrete composite beam with notched web are introduced; then, a group of formulas about the bending capacity, slip between the steel beam and the concrete flange, and the deflection are introduced; after that, the bending behavior, slip effect and bearing characteristic of the steel-concrete composite beam with notched web are studied on 4 specimens, which are tested by applying two concreted vertical loads on the top of concrete flange. And the finite element model is adopted to analyze the results of the 4 specimens; finally, the reliabilities of the formulas are verified by comparing the results of theoretical formulas, the results of tests and that of finite element analysis. Study shows that the bend behavior and shear behavior are fine, and the popularization of this new kind of composite beam which can be broadly used in building engineering will save the consumption of steel. 相似文献
20.
Based on concepts of mechanics, a mechanical model of novel type of steel plate composite shear wall is presented. The novel type of structure is formed by steel plate shear wall and T-shaped solid-web composite columns. Flexural stiffness of steel beams, lateral stiffness of the T-shaped solid-web composite columns, shear stiffness of steel plate composite shear wall and shear stiffness of beam-column connection are taken into account in the mechanical model. And the equivalent damping between steel plate and boundary is considered. Based on the deformation features of structures and the calculation hypothesis, the lateral stiffness model and the energy dissipation model of structures are developed. Meanwhile, the calculation equations of elastic ultimate and plastic ultimate of shear strength of structures are set up. The theoretical analysis results inosculate better with the results of experiment. The comparison between the result calculated from the formula and the experimental result shows that the calculation precision is high enough to meet the demand of theoretical analysis. The difference, including equivalent model, stress states, manufacturing defect and installation error, between the formula and the experiment has been further discussed. 相似文献