共查询到17条相似文献,搜索用时 203 毫秒
1.
2.
3.
4.
5.
【目的】研究等温结晶处理对木纤维/聚乳酸复合材料结晶、物理和力学性能的影响,为提高聚乳酸复合材料的加工和使用性能提供依据。【方法】采用热压成型方式制备纯聚乳酸板材和杨木纤维(WF)/聚乳酸(PLA)复合材料,在冷却过程中将材料置于不同温度(90、100、110、120和130℃)下进行等温结晶处理,通过示差扫描量热仪(DSC)分析PLA及其复合材料的结晶度和熔融特性,利用偏光显微镜(POM)观察等温结晶处理条件下PLA的结晶过程,结合结晶形态分析等温结晶处理对PLA结晶性能的影响。基于扫描电镜(SEM)和凝胶色谱仪(GPC)等测试手段表征材料的微观结构和分子质量,分析其对材料物理力学性能的影响。【结果】等温结晶处理后,纯PLA板和WF/PLA复合材料的结晶度分别由4.6%和15.1%提高至24.8%和40.5%;经90、100和110℃等温结晶处理后,WF/PLA复合材料的冲击断面与未处理WF/PLA复合材料相比,明显有长纤维从PLA基体中拔出,等温结晶处理弱化了WF与PLA界面结合;等温结晶处理后,PLA分子质量有所下降;POM测试显示,晶体尺寸随着结晶温度升高而增大;与未处理材对比,等温结晶处理后纯PLA板的弯曲性能和拉伸强度均得到提高,WF/PLA复合材料的弯曲弹性模量增加,但弯曲强度和拉伸强度在多数处理条件下都有所降低。【结论】等温结晶处理后,纯PLA板和WF/PLA复合材料的结晶度均提高,且木纤维促进晶核生成,WF/PLA复合材料的结晶度增加更多;等温结晶温度低,晶体尺寸变小,等温结晶温度高,晶体尺寸变大;等温结晶处理后,纯PLA板的抗弯强度和拉伸强度得到提高,WF/PLA复合材料的力学性能变化规律不明显。等温结晶处理对纯PLA板和WF/PLA复合材料力学性能影响不同,可能与等温结晶处理后弱化WF与PLA界面结合有关。 相似文献
6.
为探索纳米CaCO3对增强生物可降解复合材料力学性能的影响,采用混炼、注射成型工艺制备纳米CaCO3改性木纤维/聚乳酸复合材料,研究了纳米粒子添加量(1wt%,2wt%,3wt%,4wt%)及粒子预处理(偶联剂,硬脂酸,偶联剂-硬脂酸)对材料拉伸性能与冲击性能的影响。随着CaCO3添加量增加,复合材料力学强度先增大后减小,质量分数2%时材料拉伸强度和冲击强度分别提高8%与20%,粒子的增韧效果明显。预处理不仅能增强木纤维与聚乳酸的结合,也提高了纳米粒子分散性,增强材料整体力学性能。纳米粒子在聚合物基体中的分散性及其与聚合物界面结合是影响材料性能的关键。 相似文献
7.
采用一步法连续挤出技术将杨木针状纤维与高密度聚乙烯(HDPE)进行熔融复合制备木塑复合材料(NF-WPC).用正交试验法分析纤维尺寸、纤维添加量、偶联剂含量和润滑剂含量4个因子对NF-WPC力学性能影响的显著性;用扫描电子显微镜观察分析NF-WPC中木纤维与HDPE的界面结合状况;提出优化的工艺配方并与相同木材含量的木粉/HDPE复合材料进行对比研究.结果表明:针状木纤维的含量对NF_WPC冲击强度影响显著,对弯曲性能和拉伸性能的影响高度显著;偶联剂马来酸酐接枝聚乙烯(MAPE)的添加量对NF_WPC的拉伸强度、断裂伸长率和冲击强度影响显著;在本文的试验范围内,木纤维尺寸和润滑剂石蜡的含量对NF-WPC力学性能的影响不显著.确定的优化工艺配方为:木纤维长度为3~4mm、长径比为8~11,木纤维含量60%,MAPE含量4%,石蜡含量0.3%;采用优化工艺制备的NF_WPC的弯曲强度、弯曲模量、拉伸强度、拉伸模量和冲击强度分别为58.7 MPa、3.0 GPa、39.6 MPa、4.0 GPa和12.7 kJ·m-2.除冲击韧性略低外,用优化工艺配方制备的NF_WPC其他力学性能均高于用同比例木粉制备的木塑复合材料. 相似文献
8.
目前,溶液浇铸法制备纳米纤维素/聚乳酸复合材料,常将纳米纤维素直接加入聚乳酸,导致制备的复合材料各项机械性能普遍降低。为了改善其机械性能,笔者采用聚乙二醇2000作为塑化剂处理纳米纤维素,制备聚乳酸/纳米纤维素/聚乙二醇三相复合材料。通过对复合材料的微观形貌观测,力学性能分析和热稳定性分析来确定聚乙二醇的影响机制。试验结果表明,添加2%~4%聚乙二醇2000的三相复合材料的拉伸强度、撕裂强度与断裂伸长率得到了提高,材料的热稳定性相对纯聚乳酸发生了下降。而随着聚乙二醇含量逐渐增加至8%,材料的拉伸强度、撕裂强度与断裂伸长率都出现了降低,而其热稳定性回升,复合材料的玻璃化转化温度(TG)大约提升了5~6℃。同时,研究发现保持一定的聚乙二醇/纳米纤维素添加比例可获得分散均匀、性能优良的复合材料,团聚现象明显减少。综上,经过一定量的聚乙二醇2000表面改性可促进纳米纤维素在聚乳酸中的均匀分散,从而增强复合材料的综合机械性能。 相似文献
9.
研究了球磨胡桑木粉苄基化改性后的增重率与材料热塑性以及力学性能的关系。随着增重率的增加,即胡桑木粉苄基化反应程度的提高,产物的热塑性变好,但材料的拉伸强度和弯曲强度增加到一定程度后,反而随着增重率的增加而下降。以胡桑木粉苄基化产物为基体,分别以球磨胡桑木粉、蒙脱土为增强材料进行共混制备复合材料,探讨增强材料与木粉苄基化产物基体的质量比对复合材料力学性能的影响。试验结果表明,复合材料的力学性能优于胡桑木粉苄基化产物,其拉伸强度和弯曲强度随增强材料质量分数的增加而先增加后降低。 相似文献
10.
11.
采用捏合法制备木纤维-聚乳酸(WF-PLA)复合材料。通过凝胶色谱法(GPC)和差示扫描量热法(DSC)研究捏合温度和木纤维水分对WF-PLA生物质复合材料中聚乳酸分子质量及热性能的影响。结果表明:捏合温度对WF-PLA生物质复合材料中PLA性能影响显著。随着捏合温度由180℃升高到200℃,WF-PLA复合材料中PLA的重均分子质量(M珚w)明显下降,数均分子质量(M珚n)在200℃时也明显下降,在190℃时,PLA分子多分散系数最小。不同捏合温度的WF-PLA复合材料中,PLA熔融温度略有不同,熔融温度变化与PLA分子质量相关。木纤维水分对捏合法制备的WF-PLA复合材料中PLA的分子质量和热性能的影响不显著。 相似文献
12.
13.
使用DSC对纯聚乳酸(PLA)、木纤维(WF)/PLA复合材料的熔融和非等温结晶过程进行测定和分析。结果显示木纤维的加入一定程度上会在影响PLA的结晶性能,能够促进PLA的异相成核从而提高其结晶度,但晶核密度的增加会减小晶核之间的空间从而阻碍结晶生长,并且降低结晶的生长速率。本研究还分别采用Avrami方程和莫志深方法对实验结果进行分析,结果表明在非等温结晶过程中,降温速率对PLA结晶性能的影响比较显著。降温速率越快,材料的结晶温度越低,形成结晶的形态也越不一致,结晶度也越低。 相似文献
14.
Sadegh Maleki Akbar Rostampsour Haftkhani Mosayeb Dalvand Mehdi Faezipour Mehdi Tajvidi 《林业研究》2012,23(3):481-490
We determined the effects of the penetration depth and spline material and composite material type as well as joining method on bending moment resistance under diagonal compression and tension in common wood panel structures. Composite materials were laminated medium density fiberboard (MDF) and particle board. Joining methods were buttand miter types. Spline materials were high density fiber board (HDF).The penetration depths of plywood, wood (Carpinus betolus) and splinewere 8, 11 and 14 mm. The results showed that in both diagonal compression and tension, MDF joints are stronger than particle board joints,and the bending moment resistance under compression is higher compared with that in tension. The highest bending moment resistance under tension was shown in MDF, butt joined using plywood spline with 8 mm penetration depth, whereas under compression bending moment resistance was seen in MDF, miter joined with the HDF spline of 14 mm penetration depth. 相似文献
15.
Since the structure of oil palm wood varies dramatically, the property gradients of oil palm wood within a trunk are of great interest. In this study, the physical (density, water uptake and swelling in the radial direction) and mechanical properties (bending modulus of elasticity and strength, compressive modulus of elasticity and strength in the direction parallel to the fiber, compressive strength in the direction perpendicular to the fiber and shear strength in the direction parallel to the fiber) of oil palm wood for a whole trunk were examined. The water uptake, compressive strength in the direction perpendicular to the fiber, shear strength in the direction parallel to the fiber, bending modulus of elasticity and strength and compressive modulus of elasticity and strength in the direction parallel to the fiber appeared to be independent of trunk height but tended to be related to the relative distance from surface or density by a single master curve. However, the swelling in the radial direction of the oil palm wood was not correlated with the relative distance from the surface, trunk height or density. Finally, property map of oil palm wood for a cross section at any height was prepared for practical use. 相似文献
16.
Liva Pupure Janis Varna Roberts Joffe Fredrik Berthold Arttu Miettinen 《Wood material science & engineering》2020,15(2):76-86
ABSTRACTComposites formed from wood fibers and man-made cellulosic fibers in PLA (polylactic acid) matrix, manufactured using sheet forming technique and hot pressing, are studied. The composites have very low density (due to high porosity) and rather good elastic modulus and tensile strength. As expected, these properties for the four types of wood fiber composites studied here improve with increasing weight fraction of fibers, even if porosity is also increasing. On the contrary, for man-made cellulosic fiber composites with circular fiber cross-section, the increasing fiber weight fraction (accompanied by increasing void content) has detrimental effect on stiffness and strength. The differences in behavior are discussed attributing them to fiber/ fiber interaction in wood fiber composites which does not happen in man-made fiber composites, and by rather weak fiber/matrix interface for man-made fibers leading to macro-crack formation in large porosity regions. 相似文献