共查询到20条相似文献，搜索用时 578 毫秒
1.
基于摩擦学理论和传热学,利用ANSYS建立圆环分区直齿热磨机磨片的稳态温度场和热变形的三维热分析有限元模型,分析该磨片处于热平衡状态下的温升和热变形.结果表明,热变形对磨片之间间隙有一定影响. 相似文献
2.
热磨机磨盘加压与间隙微调装置浅析 总被引：2，自引：0，他引：2
卢盛江 《林业机械与木工设备》1994,(4):15-16
对传统的和液压伺服控制的热磨机磨盘加压与间隙微调装置进行了对比分析，并就前者改造为后者提出意见。 相似文献
3.
热磨机磨片的齿形结构是磨片和原料间传递能量的主要方式,它与木片原料被研磨时的运动状态和研磨时间,以及纤维制备过程中纤维质量和设备的能耗密切相关。笔者根据磨片破碎区、粗磨区、精磨区的齿形结构、磨齿倾角、周向齿等参数对纤维分离能耗的影响以及磨片的设计要求,设计了一种有利于降低纤维分离能耗的热磨机磨片,并运用ABAQUS软件对磨片进行了静力学分析,分析结果表明磨片受到的静力作用对自身影响很小,设计满足要求。 相似文献
4.
热磨机是生产中密度纤维板的主要设备,随着人造板在日常生活中的需求不断扩大,人们对它的质量要求也越来越高。磨片是热磨机的配套产品,磨片相当于机床上的刀具,在热磨机上起着不可轻视的作用, 它的应用适当与否直接影响人造板的质量。从几家人造板生产厂对磨片反馈的情况看,普遍认为有以下几种情况:磨机功耗大;纤维状态(纤维板组成单元)不稳定;磨片损坏快等。针对这些问题,我们前往生产厂家实地考察,并认真讨论,查阅资料,深入分析,还咨询了有关国外磨机专家,一致认为出现上述问题的原因是由于动、静磨片盘间隙调整不当所致。笔者从以下几个方面加以分析说明: 相似文献
5.
6.
根据数控木工加工中心伺服进给系统的特点,通过对其机械传动机构进行设计计算确定其主要结构尺寸和选择驱动元件;并建立了伺服驱动系统数学模型,对此非线性离散控制系统进行了仿真,得出了数字控制器的脉冲传递函数. 相似文献
7.
阐述了热磨机磨片的主要功能,并对影响磨片齿形结构设计的三个主要因素进行了分析.研究表明,原料的纤维特性、热磨机的性能、磨片的制造工艺对磨片齿形的结构设计、纤维分离的机理及磨片综合性能等有不同程度的影响. 相似文献
8.
通过对扇块分区热磨机磨片进行热应力分析,得到磨片的最大应力值和最大变形,并运用ANSYS的优化模块对磨片进行结构优化设计,得到了能够满足各项性能要求的新磨片,并最终达到了产品设计的轻量化要求. 相似文献
9.
10.
11.
《Scandinavian Journal of Forest Research》2012,27(5):427-435
In Scandinavia, moose (Alces alces L.) sometimes cause severe browsing damage to economically-important pine. Moose-vehicle accidents have spurred construction of fences along roads, and these may interfere with moose migration between summer and winter ranges, or the road alone may be a barrier. If this happens and moose build up along roads, landowners may suffer economically. Therefore, this study investigated whether roads, fences or other factors influence the use of young pine stands by moose. Eighty stands along roads in northern Sweden were evaluated in which individually-browsed branches were counted on 9972 pines. Moose browsing was not significantly related to birch (Betula pendula Roth, B. pubescens Ehrh.) density, nor did it differ between pines (Pinus contorta Douglas or P. sylvestris L.). However, increased pine density, site productivity and proximity to a highway were associated with increased browsing. Further large-scale studies are needed to understand moose habitat selection and the effects of roads. 相似文献
12.
《Scandinavian Journal of Forest Research》2012,27(3):206-217
The root systems of 2-yr-old Picea glauca, Picea mariana and Pinus banksiana seedlings were submitted to various frost temperatures during an artificial frost to induce different levels of root damage. Frost-damaged and control seedlings were placed in a greenhouse under high and low soil moisture regimes. Seedling growth and physiology were evaluated periodically. Seedling survival was reduced when root damage reached levels of 60-80%. Root systems of all three species showed partial to total recovery by the end of the experiment. In general, root freezing damage caused reductions in seedling growth, with these reductions becoming less significant over time. Root damage had little to no effect on black spruce and jack pine seedling physiology, while white spruce CO 2 uptake decreased with increasing root damage. Shoot nitrogen content of all three species decreased slightly with increasing root damage. 相似文献
13.
Contour hedgerows of multipurpose tree species in the sloping tea lands of Sri Lanka are expected to reduce soil erosion and
also add significant amounts of plant nutrients to the soil via periodic prunings. The objective of this experiment was to characterize the biomass decomposition pattern and quantify the
amount of nutrients added through prunings of six tree species (Calliandra calothyrsus, Senna spectabilis, Euphatorium innulifolium, Flemingia congesta, Gliricidia sepium and Tithonia diversifolia) currently being used in hedgerows associated with tea. Withered leaf and stem prunings (50 g) were enclosed in 2-mm litter
bags, placed at 5-cm depth and retrieved after one, three, six, nine and 12 weeks. Loss of initial dry weight, N, P and K
was measured. Single exponential decay function adequately described both dry weight and nutrient loss. Tree species differed
significantly in their rate of breakdown with decomposition constants (k) varying from 0.0299 to 0.2006 week−1 for leaves and from 0.0225 to 0.0633 week−1 for stems. Gliricidia showed the highest k for leaves with the rest in the following descending order: Senna > Tithonia ≥ Euphatorium > Calliandra > Flemingia. A similar pattern was observed for loss of all nutrients with Calliandra and Flemingia always having lower k values than the rest. Although N immobilization was not observed, immobilization of P and K was observed
during the first week of incubation in some species, particularly in stem prunings. Annual biomass of prunings differed significantly
between tree species in the following descending order: Calliandra > Senna > Flemingia > Tithonia > Gliricidia > Euphatorium. Calliandra added the greatest amount of nutrients annually to the soil with Euphatorium adding the least. Calliandra prunings provided the annual total K requirement and 49% of the N requirement of mature tea. However, none of the species
provided more than 5% of the P requirement. It is concluded that among the tree species tested, Calliandra and Flemingia are the most suitable for contour hedgerows in tea plantations of this agroclimatic region because of their higher soil nutrient
enrichment capacity and slower decomposition rates which would minimize leaching losses.
This revised version was published online in June 2006 with corrections to the Cover Date. 相似文献
14.
《Scandinavian Journal of Forest Research》2012,27(2):118-130
The effects of seed weight and seed type on seedling growth of Pinus sylvestris (L.) were studied by seeding individually weighed orchard and stand seed in different mixtures under harsh (direct seeding in field) and optimal (seeding in nursery) conditions. In the nursery experiment an increase in the seed weight from 3 to 7 mg increased the seedling height by 10-27% and total weight by 27-113%, and decreased the height/diameter ratio by 5-6% after 2 yrs. With elimination of seed weight effects, orchard seedlings were 2% taller than stand seedlings in year 2. Without elimination of seed weight effects, orchard seedlings were 7-13% taller. In the field experiment an increase in the seed weight from 3 to 7 mg increased seedling height by 18-65%, stem volume by 81-274% and the number of top-buds by 23-34% in year 5. After elimination of seed weight effects, orchard seedlings were 7-13% taller than stand seedlings and without elimination of seed weight effects 20-21% taller after 5 yrs. Even after elimination of both seed weight and genetic effects orchard seedlings were 3-9% larger than stand seedlings in the field experiment. In conclusion, the influence of seed weight and seed type on growth traits and slenderness is highly significant and the influence seems to be greater in harsh conditions. 相似文献
15.
《Wood material science & engineering》2013,8(2):76-84
Abstract Wood in general and wooden studs in particular are often distorted owing to uneven shrinkage during the drying process in the sawmill. Twist is often the most detrimental of all types of distortion, and it is caused by spiral grain in combination with variations in moisture content. For sawmills, the objective is to produce dried, straight boards, and one method of dealing with boards with excessive spiral grain is to sort them out and then dry them in a pretwisted position to obtain straight boards after drying. A model using the finite element (FE) method for the simulation of drying twist distortions was first calibrated against laboratory experiments in which boards were dried with and without restraints and pretwists. After the calibration, the FE results were compared with industrial test results for boards that were dried without restraints or with restraints with zero pretwist, i.e. straight restraints. The FE model used an elastic–ideally plastic material model to obtain permanent deformations. The calibration was to set the yield stresses so that there was a good match between FE results and results from the laboratory experiments. The comparison between the industrial test results and the FE results showed that the FE model is capable of realistic simulations of drying boards with and without restraints and presumably also pretwists. 相似文献
16.
Steven Maranz Amadou Niang Antoine Kalinganire Djeneba Konaté Bocary Kaya 《Agroforestry Systems》2008,72(3):231-239
Baobab leaves form an important part of the local diet in Sahel countries and elsewhere in Africa. Existing leaf nutritional
data and agroforestry performance information are based solely on Adansonia digitata L., the baobab of continental Africa. The introduction potential of Adansonia species from the center of diversity in Madagascar and from Australia remains untapped. To assess this potential, the mineral
contents and B1 and B2 vitamin levels of dried baobab leaves were determined for five-year old trees of A. digitata, A. gibbosa (A. Cunn.) Guymer ex D. Baum, A. rubrostipa Jum. & H. Perrier (syn. A. fony Baill.), A. perrieri Capuron and A. za Baill. grown in an introduction trial in Mali. Nutritional data were evaluated against survival and vigor to identify promising
germplasm. Leaf vitamin and crude protein contents were highest in the Madagascar species, especially A. rubrostipa (B1 88 mg 100 g−1, B2 187 mg 100 g−1, protein 20.7% dry weight). However, the local species far outperformed the introductions in survival, tree height, basal
diameter and resistance to termites. We suggest grafting as a way of harnessing the vigor of well-adapted local baobab varieties
to the superior nutritional profiles of A. rubrostipa and others. Cross-species grafting tests in Adansonia were successful, thus creating new agroforestry possibilities with different scion/rootstock combinations. 相似文献
17.
Astra Zaluma Lauma Bruna Darta Klavina Natalija Burnevica Kristine Kenigsvalde Andis Lazdins Talis Gaitnieks 《Forest Pathology》2019,49(6)
Heterobasidion parviporum and Heterobasidion annosum are widely distributed root‐rot fungi that infect conifers throughout Europe. Infection of conifer stumps by spores of these pathogens can be controlled by treating fresh stumps with a competing non‐pathogenic fungus, Phlebiopsis gigantea. In this study, growth of three Latvian strains of P. gigantea and the biological control agent ‘Rotstop’ strain was evaluated in stem pieces of Norway spruce, Scots pine, lodgepole pine, Douglas‐fir, Weymouth pine, Siberian larch and Sitka spruce. The growth rates of one H. parviporum and one H. annosum isolate were also measured in the same stem pieces. The growth rate of P. gigantea varied greatly in wood of different conifer species. It was higher in the three pine species, lower in Norway spruce and lowest in Sitka spruce and Siberian larch, and in Douglas‐fir, this fungus did not grow. The largest area of wood occupied by P. gigantea was in lodgepole pine. Growth of Latvian isolates of P. gigantea in the wood of Pinus and Picea species was comparable to that of the Rotstop isolate. Consequently, stump treatment with local P. gigantea isolates should be recommended. However, our results suggest that Douglas‐fir stump treatment against Heterobasidion by P. gigantea may be ineffective and other stump treatment methods should be considered. 相似文献
18.
《Scandinavian Journal of Forest Research》2012,27(1):53-61
This study investigated the stand structure in pine, spruce and deciduous forests in the border district of Finland and Russia. A total of 46 mature forest stands was selected as pairs, the members of each pair being as similar as possible with respect to their forest site type, age, moisture and topography. The stands were then compared between the two countries by means of basal areas and number of stems. The proportions of dominating tree species were 2-12% lower, and correspondingly the proportions of secondary tree species higher, in Russian forests. The density of the forest stock was also higher in each forest type in Russia. The forests in the two countries differed most radically in terms of the abundance of dead trees. The amount was two to four times higher in Russian deciduous and spruce forests, and in pine forests the difference was 10-fold. The stand structures indicated that Russian coniferous stands, in particular, were more heterogeneous than intensively managed pine and spruce stands in Finland. 相似文献
19.
《Scandinavian Journal of Forest Research》2012,27(1):15-27
The root collar diameter and the height:diameter ratio are of particular importance in container-grown seedlings where a high density in the containers may produce spindly seedlings. Temperature regimes and light quality are known to affect plant growth. The aim of this study was to identify responses in Picea abies (L.) Karst. seedlings grown with light providing different red:far-red ratios and under temperature regimes with alternating day (DT) and night temperature (NT) from negative (DT < NT) to positive (DT > NT) difference (DIF) between DT and NT. Experiments were conducted in controlled environment chambers and in a daylight phytotron. Only limited thermoperiodic responses appeared in P . abies seedlings with respect to seedling height and dry weight accumulation. The formation of terminal buds, however, was clearly delayed in seedlings grown at negative DIF. The results indicate a requirement for day extension light that is high in far-red, to prevent terminal bud formation under natural short-day conditions. An extended study should be conducted to clarify the minimum level of light intensity and the optimal light quality needed to prevent terminal bud formation under natural short-day conditions. 相似文献
20.
本文分析了CAD在设计中引起的正面和负面影响,并进行了系统的阐述,从而使设计者在应用中能够保持客观的态度。 相似文献