首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 31 毫秒
1.
Chemical treatment is an often-followed route to improve the physical and mechanical properties of natural fiber reinforced polymer matrix composites. In this study, the effect of chemical treatment on physical and mechanical properties of jute fiber reinforced polypropylene (PP) biocomposites with different fiber loading (5, 10, 15, and 20 wt%) were investigated. Before being manufactured jute fiber/PP composite, raw jute fiber was chemically treated with succinic anhydride for the chemical reaction with cellulose hydroxyl group of fiber and to increase adhesion and compatibility to the polymer matrix. Jute fiber/PP composites were fabricated using high voltage hot compression technique. Fourier Transform Infrared spectroscopy (FTIR) and Scanning Electron Microscopy (SEM) tests were employed to evaluate the morphological properties of composite. Succinic anhydride underwent a chemical reaction with raw jute fiber which was confirmed through FTIR results. SEM micrographs of the fractured surface area were taken to study the fiber/matrix interface adhesion and compatibility. Reduced fiber agglomeration and improved interfacial bonding was observed under SEM in the case of treated jute fiber/PP composites. The mechanical properties of jute/PP composite in terms of Tensile strength and Young’s modulus was found to be increased with fiber loading up to 15 wt% and decreased at 20 wt%. Conversely, flexural strength and flexural modulus increased with fiber loading up to 10 wt% and start decreasing at 15 wt%. The treated jute/PP composite samples had higher hardness (Rockwell) and lower water absorption value compared to that of the untreated ones.  相似文献   

2.
Abstact  The thermal and mechanical properties of castor oil/polycaprolactone-based polyurethane (CPU) films and polyurethane biocomposites reinforced with hemp fibers (HCPU) were investigated. Although similar films can be synthesized from petroleum, the main interest in studying these biomass-based composites is based on the fact that both fiber and matrix are derived from renewable resources. In this study, castor oil was used as a polyol for polyurethane films and hemp fiber was used to reinforce the biocomposites. To control the mechanical properties of CPU and HCPU, polycaprolactone diol (PCL) was added to the polyol mixture. Varying the mixing ratio of castor oil and PCL, the thermal and mechanical properties of the CPU and HCPU samples were investigated by using FT-IR, DSC, DMTA, Minimat, and SEM. In an attempt to improve interfacial adhesion between the fiber and matrix biocomposites, hemp fiber was reacted with MDI. FE-SEM micrographs showed that the surface of the hemp fiber became smoother after reaction with MDI. Urethane bonding formation was confirmed by FT-IR.  相似文献   

3.
Natural fiber reinforced polypropylene (PP) biocomposites were fabricated by blending long-and-discontinuous (LD) natural fibers (NF) with LD PP fibers. Firstly, random fiber mats were prepared by mixing NFs and PP fibers using a carding process. Then, heat and pressure were applied to the mats, such that the PP fibers dispersed in the mats melted and flowed out, resulting in the formation of consolidated sheets upon subsequent cooling. The effect of the fiber volume fraction on the mechanical properties of the bio-composites was scrutinized by carrying out tensile and flexural tests and observing the interface between the fiber and matrix. It was observed that the natural LD fiber content needs to be maintained at less than the nominal fiber fraction of 40 % by weight for the composites fabricated using the current method, which is quite low compared to that of continuous or short fiber reinforced composites. The limited fiber fraction can be explained by the void content in the biocomposites, which may be caused by the non-uniform packing or the deficiency of the matrix PP fibers.  相似文献   

4.
The chemical and morphological properties of ramie fibers treated by chemical surface modification were examined with Fourier transform infrared (FT-IR) spectroscopy. The mechanical and thermal decomposition properties were evaluated with respect to tensile strength, tensile modulus and thermogravimetric analysis (TGA). Surface morphological changes were investigated with scanning electron microscopy (SEM). Finally, the capabilities of composites reinforced with various chemically treated fibers were analyzed by investigating tensile and impact strengths. Additionally, the thermal mechanical properties of the composites were investigated with thermal mechanical analysis (TMA). Based on the results of these analyses, we concluded that pectin, lignin and hemicellulose were removed and thermal stability was increased with chemical treatments. The composites reinforced with ramie fiber showed better properties compared with pure PLA matrix with respect to tensile and impact strengths. The peroxide-treated fiber composite had the smallest thermal expansion.  相似文献   

5.
Sugar palm fiber is one of the most abundant natural fibers used in biocomposites. However, prediction of the mechanical properties of such natural fiber reinforced composites is still challenging. Most of the theoretical modelings are based the micromechanical method. There have been little studies involving statistical approach for prediction of mechanical properties of natural fiber reinforced composites. In this study, the tensile properties of short sugar palm fiber-reinforced high impact polystyrene (SPF-HIPS) composites obtained by means of statistical approach were investigated and compared with the experimental observations and with micromechanical models available in the literature. Statistical approach was used to predict the performance of the composite part with different fiber loadings. A two-parameter Weibull distribution function was used to model the fiber length distribution in the composite. For the experimental validation, the composites were prepared by hot compression technique for different fiber loadings (10 %, 20 %, 30 %, 40 % and 50 % by weight). Tensile testing of the composites was carried out according to ASTM D638 to obtain the composites tensile strength and modulus of elasticity. Experimental results showed that the tensile strength of the composite reduced due to the addition of sugar palm fibers, whereas the elastic modulus increased by a factor of up to 1.34. The current statistical model predicted the tensile properties of SPF-HIPS composite close to the experimental values. It was found that statistical approach with standard micromechanical models can be used to predict the mechanical properties of sugar palm fiber reinforced HIPS composites. Hence, this study could assist in decisions regarding the design of natural fiber reinforced composite products.  相似文献   

6.
Kenaf/empty fruit bunch/polylactic acid (kenaf/EFB/PLA) hybrid biocomposites were prepared using hot press technique. The ratio of fiber to polylactic acid was set at 60:40 with 1:1 ratio between kenaf and empty fruit bunch fibers. Physical, mechanical and thermal properties of hybrid biocomposites were subsequently characterized using Fourier transform infrared spectroscopy, scanning electron microscope, X-ray diffraction, thermogravimetric analysis, differential scanning calorimetry, tensile and water absorption tests. Test results indicated that mechanically stronger fiber was able to support the weaker fiber. Hybrid fiber biocomposite had higher crystallinity as compared to single fiber biocomposite. Water absorption of hybrid composite was higher as compared to single fiber composite. Thermal result revealed that hybridization of fiber was not significantly influence the thermal properties of composites. However, the presence of two different fibers proposed good wettability properties, which could reduce the formation of voids at the fibers-polymer interface and produce composites with high stiffness and strength.  相似文献   

7.
Poly(lactic acid) (PLA)/jute fiber biocomposites with: i) untreated jute fiber, ii) NaOH treated jute fiber, and iii) (NaOH+silane) treated jute fibers were prepared by melt extrusion process. Microcellular foaming of the injection molded samples was carried out by using single stage batch process. The effects of jute fiber content as well as that of matrix-fiber phase adhesion, in composites with surface treated jute fibers, on the foam microstructure were studied. Further, water absorption, thickness swelling, and biodegradation behavior of the foamed biocomposites were studied and correlated with their foam microstructures. It was observed that on increasing jute fiber content in PLA/JFU biocomposites, cell density increased from 6.5×107 to 8.1×107, while the cell size and expansion ratio decreased from 40 to 23 μm and 2.41 to 1.45, respectively. Again, on increasing the extent of the jute fiber surface treatment in the biocomposites, cell size and expansion ratio increased from 40 to 78 μm and 2.41 to 2.80 respectively. This study also revealed that the rate of biodegradation accelerated with increase in the jute fiber content in the biocomposites while the same retarded with increase in the extent of jute fiber surface treatment.  相似文献   

8.
This study has examined the flexural properties of natural and chemically modified coir fiber reinforced cementitious composites (CFRCC). Coir fibers of two different average lengths were used, and the longer coir fibers were also treated with a 1 % NaOH solution for comparison. The fibers were combined with cementitious materials and chemical agents (dispersant, defoamer or wetting agent) to form CFRCC. The flexural properties of the composites, including elastic stress, flexural strength, toughness and toughness index, were measured. The effects of fiber treatments, addition of chemical agents and accelerated ageing of composites on the composites’ flexural properties were examined. The results showed that the CFRCC samples were 5–12 % lighter than the conventional mortar, and that the addition of coir fibers improved the flexural strength of the CFRCC materials. Toughness and toughness index, which were associated with the work of fracture, were increased more than ten times. For the alkalized long coir fiber composites, a higher immediate and long-term toughness index was achieved. SEM microstructure images revealed improved physicochemical bonding in the treated CFRCC.  相似文献   

9.
Jute fibers have immense potential to be used as natural fillers in polymeric matrices to prepare biocomposites. In the present study jute fibers were surface treated using two methods: i) alkali (NaOH) and ii) alkali followed by silane (NaOH+Silane) separately. Effects of surface treatments on jute fibers surface were characterized using fourier transform infrared spectroscopy (FT-IR) and scanning electron microscopy (SEM) analyses. Further, the effects of surface treatments on jute fibers properties such as crystallinity index, thermal stability, and tensile properties were analyzed by X-ray diffraction method (XRD), thermo gravimetric analysis (TGA), and single fiber tensile test respectively. The effects of surface treatment of jute fibers on interphase adhesion between of poly(lactic acid) (PLA) and jute fibers were analyzed by performing single fiber pull-out test and was examined in terms of interfacial shear strength (IFSS) and critical fiber length.  相似文献   

10.
Natural fibers are largely divided into two categories depending on their origin: plant based and animal based. Plant based natural jute fiber reinforced polypropylene (PP) matrix composites (20 wt% fiber) were fabricated by compression molding. Bending strength (BS), bending modulus (BM), tensile strength (TS), Young’s modulus (YM), and impact strength (IS) of the composites were found 44.2 MPa, 2200 MPa, 41.3 MPa, 750 MPa and 12 kJ/m2, respectively. Animal based natural B. mori silk fiber reinforced polypropylene (PP) matrix composites (20 wt% fiber) were fabricated in the same way and the mechanical properties were compared over the silk based composites. TS, YM, BS, BM, IS of silk fiber reinforced polypropylene composites were found 55.6 MPa, 760 MPa, 57.1 MPa, 3320 MPa and 17 kJ/m2 respectively. Degradation of composites in soil was measured upto twelve weeks. It was found that plant based jute fiber/PP composite losses its strength more than animal based silk fiber/PP composite for the same period of time. The comparative study makes it clear that mechanical properties of silk/PP composites are greater than those values of jute/PP composites. But jute/PP composites are more degradable than silk/PP composites i.e., silk/PP composites retain their strength for a longer period than jute/PP composites.  相似文献   

11.
TiO2/NBR-PVC hollow fibers were spinned by NBR casting solution blended PVC with nano-titanium dioxide (TiO2). The effect of NBR-PVC hollow fiber damping and mechanical properties aroused by loading TiO2 were studied. Results showed that the hollow fibers loaded TiO2 increased in tensile strength, storage modulus, stiffness and glass transition temperature, while decreased in tanδpeak and breaking tensile elongation. The damping of the TiO2/NRR-PVC hollow fiber were not only linked to the dosage of TiO2, but also related to the degree of dispersion in matrix.  相似文献   

12.
Soyprotein-jute fiber composites developed using water without any chemicals as the plasticizer show much better flexural and tensile properties than polypropylene-jute composites. Co-products of soybean processing such as soy oil, soyprotein concentrate and soy protein isolates are inexpensive, abundantly available and are renewable resources that have been extensively studied as potential matrix materials to develop biodegradable composites. However, previous attempts on developing soy-based composites have either chemically modified the co-products or used plasticizers such as glycerol. Chemical modifications make the composites expensive and less environmentally friendly and plasticizers decrease the properties of the composites. In this research, soyprotein composites reinforced with jute fibers have been developed using water without any chemicals as plasticizer. The effects of water on the thermal behavior of soyproteins and composite fabrication conditions on the flexural, tensile and acoustic properties of the composites have been studied. Soyprotein composites developed in this research have excellent flexural strength, tensile strength and tensile modulus, much higher than polypropylene (PP)-jute fiber composites. The soyprotein composites have better properties than the PP composites even at high relative humidity (90%).  相似文献   

13.
Polyacrylonitrile (PAN) precursor fibers were modified for different periods of time using hydrogen peroxide aqueous solution. A variety of tests were employed to characterize the fibers. The modification could induce cyclization and oxidation in the precursor fibers, as reflected by the changes in length and diameter of the fibers, and the results of Fourier transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS). Compared with the unmodified fiber, the modified fibers released less heat during a heating process similar to stabilization of PAN precursor fiber. Also, the modified fibers showed lower characteristic temperatures on differential scanning calorimetry (DSC) thermograms, and lower onset temperature of weight loss on thermal gravimetry (TG) curves. The modified fibers had more surface defects and hence exhibited lower tenacity and tensile modulus. Compared with the unmodified fibers, however, the modified fibers had smoother surface and fewer defects after stabilization. The strain decreased with increasing temperature under a constant tension for all the fibers. At the temperatures above 200 °C, the shrinkage of the fibers decreased with the increase of modification time, because a certain degree of cyclization and oxidation occurred in modified fibers, making them shrink less in the temperature range equivalent to stabilization.  相似文献   

14.
本研究以芒果皮渣为研究对象,采用动态超高压技术处理芒果皮渣膳食纤维,研究其粒度、膳食纤维含量以及添加了该膳食纤维对果酱流变特性的影响。结果表明：超高压改性提高了芒果皮渣膳食纤维的溶解性;随着压力的增大,膳食纤维粒径先增大后减小再增加,120 MPa时粒径达到18.218 μm。流变特性研究发现,芒果皮渣膳食纤维/果酱复配体系为非牛顿流体,具有假塑性流体特征;果酱粘度随着剪切速率的增大而减小,存在明显的剪切稀化现象;动态粘弹性测试结果表明,果酱复配体系的贮能模量（G′）与损耗模量（G′′）均随角频率的增加而呈上升趋势,损耗正切值也随着压力的增加而增加,在150 MPa时流体性质最明显。  相似文献   

15.
The dynamic mechanical properties such as storage modulus, loss modulus, and tan δ of banana fiber reinforced PF composites fabricated by RTM and CM techniques were investigated as a function of fiber content, fiber treatment, temperature and frequency. Storage modulus (E′) increases with increase in fiber content and records maximum for the composites having a fiber loading of 40 wt % at all temperature ranges. The loss modulus and damping increases to great extent by the addition of filler, a maximum was observed for filler with 10–20 wt % fiber content followed by a slight decrease in loss modulus and damping with increasing filler content. Alkali treatment of the fiber shows a great enhancement in E′ and T g of the composites. Comparison is made between the composites fabricated by RTM and CM. RTM composites exhibited higher storage modulus and lower damping compared to CM composites.  相似文献   

16.
A systematic study has been carried out to investigate the mechanical and physical properties of jute, bamboo and coir (brown and white) single fibers. The tensile properties (tensile strength, Young’s modulus and strain to failure) were determined by varying span length. Scanning electron microscopic analysis was also carried out to determine the physical properties of fibers in order to correlate with its strength, Young’s modulus and strain to failure. The Young’s modulus and strain to failure were corrected using newly developed equations. The study revealed that with increasing test span length the Young’s modulus increased and tensile strength as well as strain to failure decreased. This is because no extensometer could be used in this test set-up and machine displacement (denoted by α) was used for the modulus determination. It is also attributed that larger span length helps to minimize the machine displacement compared to smaller ones due to the reduced relative effect of slippage in the clamps. Among all fibers, the Young’s modulus of bamboo fiber was the highest. Jute fiber had smoother surface compared to other three examined fibers.  相似文献   

17.
Mechanical properties of wool fiber in the stretch breaking process   总被引：1，自引：0，他引：1  
Short wool fibers obtained by the stretch breaking process can be blended with cotton fibers and processed in a cotton spinning system, which has a high production rate. For the structural property of the wool fiber after stretch breaking, the diameter and length of the wool fiber were measured as a function of time. The diameter of the broken fibers was finer than the diameter of untreated fibers. The fiber diameter at the break point was the finest and was more irregular than the original fiber. The broken fiber showed mechanical properties of increased modulus, decreased breaking strain, and increased breaking strength.  相似文献   

18.
In effort to improve the soft properties of ramie fiber, we synthesized a carboxylate-containing polymer for use as a modifying agent, and successfully modified the ramie fiber in a strong base with the carboxylate-containing polymer. We applied Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), thermogravimetric analysis (TGA), and scanning electron microscopy (SEM) to investigate the structures of the raw and modified ramie fibers, and further investigated the mechanical and dyeing properties of the raw and modified ramie fibers. The results showed that the surface of the ramie fiber underwent significant changes due to the grafting reaction of the carboxylate-containing polymer and fiber. After the chemical modification, the flexural strength and initial modulus of the modified ramie fiber decreased while tensile strength increased, indicating that the softness of the modified ramie fiber increased though its tensile resistance remained high. In addition, the fixation of reactive dyes on the modified ramie fiber was larger than that of the reactive dyes on the raw ramie fiber. Our observations of mechanical properties and dye fixation indicated that the carboxylate-containing polymer is an effective and efficient soft modifier.  相似文献   

19.
The main objective of this research was to study the effect of fiber content variation and stearic acid (SA) treatment on the fundamental properties of unidirectional coir fiber (CF) reinforced polypropylene (PP) composites. Several percentages of filler contents were used (10–40 wt %) in order to gain insights into the effect of filler content on the properties of the composites. Coir/PP composites were fabricated by compression molding, and the properties of composites were studied by physico-mechanical and thermal properties. The results from mechanical properties such as tensile strength (TS), tensile modulus (TM) and impact strength (IS) of the CF/PP composites were found to be increased with increasing fiber content, reached an optimum and thereafter decreased with further increase in fiber content. Treatment of the coir with SA as the coupling agent enhanced the mechanical properties, crystallization temperature and crystallinity of virgin PP and water desorption of the resulting composites, resulting from the improved adhesion between the CF and PP matrix. Scanning electron micrographs (SEM) of the tensile fractured samples showed improved adhesion between fiber and matrix upon treatment with SA. Interfacial shear strength (IFSS) of the composites was measured by single fiber fragmentation test (SFFT).  相似文献   

20.
徐山青 《中国麻业》2002,24(6):33-35,32
本文通过对Henequen纤维表面进行硅烷化改性，使得纤维与树脂间存在化学键合，提高了Henequen纤维与聚羟基丁酸与戍酸酯（PHBV）树脂复合材料界面剪切强度。Henequen纤维/PHBV复合材料界面剪切强度的大小用微粘结法（Microbond)测试，结果表明纤维经硅烷处理后可使界面剪切强度从未处理情况下的5.05Mpa提高6.34Mpa。  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号