共查询到20条相似文献，搜索用时 31 毫秒
1.
用ＵＦ、ＭＵＦ胶制作三种松木胶合板，分别就单板厚度、涂胶量及抽提物含量对胶合性能的影响，松木与柳安混合树种组坯、特殊添加剂对改善胶合性能的作用进行了研究。结果表明：除了老挝松边材ＭＵＦ胶合板以外，１．５和２．０ｍｍ厚的单板胶合强度均达到或超过日本ＪＡＳ普通胶合板的要求。合板胶合强度随单板厚度增加而下降，在一定范围内增加涂胶量可以提高合板胶合强度，混合组坯及施加特殊添加剂具有改善松木单板胶合性能的作用。 相似文献
2.
对福建省主要桉树木材材性及其旋切单板厚度偏差、背面裂隙率进行检测分析,探讨木材旋切单板的适应性和制造胶合板的工艺并采用正交法优选最佳工艺参数。结果表明:尾叶桉单板背面裂隙率和单板厚度变动系数比尾巨桉小,尾叶桉用于旋切1.5 mm厚度单板质量较佳。尾叶桉木材制造胶合板较佳工艺参数:热压温度为130℃、单位压力为1.4 MPa、热压时间为1.35 min·mm-1、涂胶量为320 g·m-2。工艺条件对板材性能均有影响,桉树木材龄级对板材性能影响显著,随着桉树龄级的增大,板材性能有较大幅度提高,特别是静曲强度、弹性模量影响最为明显。 相似文献
3.
4.
《Wood material science & engineering》2013,8(2):129-138
Abstract Response surface methodology (RSM) based on a three-level, three-variable central composite rotatable design was applied to evaluate the effects of the parameters such as ratio of rice straw (Oryza sativa)/poplar (Populus deltoids) wood particle bonded with urea-formaldehyde resin in panels, species of wood veneer coating these panels and amount of adhesive in glue line on the modulus of rupture (MOR), internal bonding (IB), and thickness swelling (TS) of panels. Mathematical model equations were derived by computer simulation programming to optimize the properties of the particleboard. These equations that are second-order response functions representing MOR, IB, and TS were expressed as functions of three operating parameters of panel properties. Predicted values were found to be in a good agreement with experimental values (R 2 values of 0.96, 0.98 and 0.98 for MOR, IB, and TS, respectively). This study has shown that the RSM could efficiently be applied for modeling panel properties. It was found that the variables affected the properties of panels. Straw usage up to 30% in the mixture did not cause a significant decrease in MOR, IB, and TS. Using beech veneer and 190 g/m2 glue line had the highest MOR and lowest TS. 相似文献
5.
无醛大豆胶制备胶合板工艺及性能探究 总被引：2，自引：0，他引：2
采用生物基无醛大豆胶,通过胶合板厂现有设备对大豆胶合板的制备工艺参数进行系列实验表明:杨木胶合板最佳涂胶量为340g/m~2(双面涂胶,下同)、热压温度105℃;桉木胶合板最佳涂胶量为380g/m~2、热压温度110℃;在1～6h闭口陈化时间内,杨木、桉木胶合板的胶合强度均略有降低,但均可制备出满足国家二类板强度要求的胶合板材。实际应用过程中,我们可以根据实际情况调整上述制备工艺,以达到最佳效果。同时,利用生物基无醛大豆胶制备的板材具有较好的耐久性。 相似文献
6.
7.
Summary The purpose of this paper was to clarify the gluability and adhesion mechanism of polypropylene as a hot melt wood adhesive for plywood bonding. The gluability of plywood glued with nonpolar and modified polypropylene satisfied approximately the specification of the Japan Agricultural Standard, Designation Types 1 and 2. The moisture content (8 to 25 %) of the core veneer had no recognizable effect on gluability. The durability of polypropylene and that of modified polypropylene were the same as that of melamine-formaldehyde resin. Molten polypropylene made good contact with veneer surface, and penetrated into the lumina of wood cells and other spaces. In the separated glue lines, casts of glue which had penetrated into the vessels had many mushroom-like projections which had filled the bordered pit cavities. It was indicated that the anchoring effect of polypropylene which had penetrated into various wood elements and spaces in the veneer contributed dominantly to the gluability.Part of the paper was presented at the IUFRO-Working Party of Wood Gluing, October 2–9, 1977, Merida, Venezuela. 相似文献
8.
竹片覆面胶合板的初步研究 总被引：2，自引：0，他引：2
本文研究了以竹片为外层材料、多层杨木单板为芯层材料的复合胶合板的结构和力学性能，分析了板坯结构形式、纵向纵片厚度、单板层数及板坯压缩率与产品机械强度之间的关系。初步研究结果表明，板坯结构形式对产品的静载荷抗弯曲性能影响显著；在试验范围内，纵向竹片厚度为３．５－５．０ｍｍ、板坯压缩率在２３％左右时，竹片覆盖面杨木胶合板的综合力学性能比较理想。 相似文献
9.
玉米淀粉改性UF树脂胶合高含水率单板 总被引：2，自引：0，他引：2
采用半酯化的玉米淀粉与脲醛树脂(UF)共聚改性,探讨加入量、脲醛树脂的量比、混合比、热压条件等对胶液的黏度、稳定性、固化时间及胶合质量的影响.结果表明:当单板含水率提高到16%～18%时,用改性UF树脂生产的多层胶合板,其物理力学性能指标达到GB/T 9846.1～12-88中Ⅱ类胶合板的要求,并大幅度地降低了胶合板的制造成本. 相似文献
10.
The balance of strength between the flange and web parts of veneer strand flanged I-beam was investigated by the following
methods: (1) use of different web material types, such as plywood, oriented strand board (OSB), particleboard (PB), and medium
density fiberboard (MDF), that have different strength properties; and (2) fabrication of I-beams with low-density flanges
using low-density strands with PB web material. Replacing PB or MDF with plywood showed slight significant improvement in
the modulus of rupture but not in the modulus of elasticity of the entire I-beam. However, PB and MDF showed competent performance
in comparison with OSB, thus strengthening the promising future of the use of PB or MDF as web material to fabricate I-beams.
Hot-pressing conditions used for I-beam production exerted slightly adverse effects on the bending properties of PB, but not
on MDF, OSB, and plywood web materials. The flange density of 0.60 g/cm3 was considered to be the lower limit that provides I-beams with balanced mechanical properties and dimensional stability. 相似文献
11.
采用响应面法（RSM）,研究了单板厚度和涂胶量对桉木单板层积材（L、几）力学性能的影响。结果表明：单板厚度和涂胶量对桉木LVL的垂直加载和平行加载条件下的静曲强度（MOR┷、MOR／／）和弹性模量（MOE┷、／dOE／／）有显著影响。实验值与预测值的决定系数为0．72,0．79,0．59,0．69。本研究所获最佳工艺条件为：单板厚度2．0啪,涂胶量233g·m＾-2在此工艺条件下压制的桉木单板层积材垂直加载条件下的静曲强度（MORJ和弹性模量（MOE上）分别为85MPa与15118MPa,平行加载条件下的静曲强度（MOR／／）和弹性模量（MOE／／）分别为87MPa与15288MPa,回归模型的预测值与实验值的相对误差最大为9％,最小为3％。实验产品的MOR和MOE分别达到结构用单板层积材国家标准的优等品和140E级别。 相似文献
12.
Zephyr strand board (ZSB) and zephyr strand lumber (ZSL) were produced using zephyr made from poplar veneer to investigate the greater utilization of low-density poplar as a structural material. These materials were then compared to ordinary plywood, laminated veneer lumber (LVL) from poplar veneer, lauan plywood, and particleboard. The bending properties (moduli of rupture and elasticity) of ZSB proved superior to those of poplar plywood: and ZSL produced from poplar veneer zephyr had bending properties greater than ordinary LVL from poplar veneer. Apparently, the conversion of the poplar veneer into zephyr material had a positive effect on bending properties. Additionally, poplar ZSB had bending properties superior to those of lauan particleboard and equal to those of lauan plywood. The internal bond strength of poplar veneer ZSB was nearly two times greater than that of lauan particleboard.Parts of this report were presented at the international symposium on the utilization of fast-growing trees, Nanjing, China, October 1994. Report IV appeared inMokuzai Kogyo 49:599, 1994 相似文献
13.
The effect of compression and incision on wood veneer and plywood physical and mechanical properties
Maija Kymäläinen Akio Yamamoto Kasperi Sokka Lauri Rautkari 《Wood material science & engineering》2020,15(2):97-103
ABSTRACTDrying takes the largest share of energy in plywood production, and varying moisture content of veneers necessitates re-drying that often leads to over-dry veneers with deactivated surfaces, which may promote imperfect bonding. In order to decrease the drying time, reduce the need for re-drying of veneers, and improve the quality of plywood, birch and spruce veneers were subjected to pre-treatment by cold compression, incision, or a combination of the two. The effects of pre-treatment on the veneer and plywood quality were assessed by standard tests. Compression had a beneficial effect on water removal of the wettest veneers (spruce sapwood (SW) and birch), but some thickness reduction was observed in the veneers as well as the finished birch plywood. Compression led to thickness reduction of spruce veneers, but had no effect on SW plywood thickness likely due to higher viscoelasticity. Both compression and the combination of incising and compression levelled the moisture variation within the compressed stacks. Incision improved the modulus of elasticity of birch plywood, shear strength of SW plywood, and both bending and shear strengths of heartwood plywood. Higher surface pressure decreased the drying time of spruce SW in both plain compression and combined incision and compression pre-treatment. 相似文献
14.
为了推进建筑楼板的轻型化,提出在两张竹胶板之间粘结两根薄壁C型钢,并用竹板条封边形成一种新型钢竹组合楼板,并进行3种组合楼板的试验研究及理论分析。①钢竹界面仅用粘合剂粘结的单纯胶结型;②钢竹界面用粘合剂粘结并钉入紧固件的复合胶结型;③钢竹界面采取粘合剂与紧固件并用,且在型钢两侧粘贴竹板条的型钢强化型。试验结果表明：螺钉紧固件有效地抑制界面连续的大面积脱胶,钢竹组合效应有所改善;型钢强化型组合板整体工作性能优良,能够提供较高的刚度和很高的承载力;新型组合楼板的力学性能可以满足作为建筑楼板的需要。根据组合楼板在正常使用阶段是理想的整体弹性变形试验结果,提出组合楼板抗弯刚度的计算方法;根据破坏阶段型钢的应力状态提出组合楼板极限抗弯承载力极限计算方法,据此计算的组合楼板跨中挠度及受弯承载力的计算值与试验值吻合较好。 相似文献
15.
为评价3个杨树新品种鲁林1号、2号和3号制作胶合板的适宜性,选取生产中正应用的I-107、L35和中菏1号为对照,通过大田形质指标调查、鲜单板旋切性能评价、干单板质量评价和胶合板质量检验等方法,评价了其单板制作胶合板的适宜性及胶合板质量。试验结果表明,鲁林1、2、3号杨与3个对照相比具有较高的圆满度;鲁林1号分枝较细、分枝多且均匀,鲁林2号、3号分枝相对较少、较长、较粗;3个品种的鲜单板旋切性能均较好,干板质地良好,制作的胶合板成品符合国家标准,适宜做胶合板材。 相似文献
16.
向仕龙 《中南林业科技大学学报(自然科学版)》1999,(4)
检测了南方 １０ 种木材旋切单板的外观特征,并对以这些单板压制的胶合板的物理力学性能进行了对比和分析研究．结果表明：不同树种木材的质量密度、硬度、粗细结构及内含物对胶合板的质量密度、压缩率、胶合强度、抗弯强度和吸水厚度膨胀率分别有不同程度的影响．除刨花楠由于内含物的影响其胶合板的胶合强度达不到国家标准外,其余树种木材的各种物理力学性能指标均达到或超过 ＧＢ９８４６．４—８８ 规定的标准,但它们之间存在着一定的差别． 相似文献
17.
18.
Binderless particleboards were manufactured from sugi (Cryptomeria japonica D. Don) heartwood and sapwood by hot-pressing (pressure: 5 MPa; temperatures: 180°, 200°, and 220°C; times: 10, 20, and 30
min), and the board properties [internal bonding (IB), thickness swelling (TS), water absorption (WA)] were investigated to
evaluate the self-bonding ability. The IB, TS, and WA of the boards from sugi heartwood were better than those of the boards
from sugi sapwood at any hot-pressing condition. Therefore, it was suggested that the self-bonding ability of sugi heartwood
was superior to that of sugi sapwood. Then, sugi heartwood and sapwood powder with grain size 10 βm were used as a binder
for plywoods. Four kinds of plywood were manufactured from the combination of powder and veneer, both of which were prepared
from sugi heartwood and sapwood under the same hot-pressing conditions as the binderless particleboard, and the adhesive shear
strength and wood failure of the plywood were investigated. As a result, the plywood composed of sugi heartwood veneer met
the second grade of JAS for plywood, when either powder was used as a binder, when they were pressed at 200°C for 20–30 min
and 220°C for 10 min. 相似文献
19.
S.-Z. Chow 《Wood Science and Technology》1971,5(1):27-39
Summary Spectra resulting from chemical changes in white spruce [Picea glauca (Moench) Voss] microsections heated in air or nitrogen at high temperatures (100 to 240°C) were continuously recorded on an infrared spectrophotometer.A significant change occurred in the intensity of the 1730 cm-1 band which indicates a carbonyl absorption of carboxyl and ester groups of wood. This intensity initially decreased and the increased at a greater rate. The time periods to reach the minimum inflection point, termed the times to initiate a significant oxidative carboxylation or oxidation, showed a good curvilinear relationship with heating temperatures.Quantification of this time-temperature relationship required to reach a significant level of oxidation was achieved, using wood microsections that had extractives removed to varying degrees. It was concluded that the extractives served only as catalysts for oxidation. When drying wood at temperatures over 180°C, in addition to oxidation, pyrolytic degradation occurred.Chemical evidence was further confirmed by tests of plywood panels bonded with phenolformaldehyde glue. Three separate types of veneers were investigated—non-extracted, acetone extracted, and veneer with the surface chemically stabilized by treatment with sodium borohydride. The results suggest that the time period to reach a significant level of oxidative carboxylation is also the time period to initiate a wood surface inactivated to polymer adhesion.The author wishes to thank Miss D. Bouchard and Mr. H. N. Mukai for their assistance in the experiments. Appreciation also is due to Mr. H. MacLean for a critical review of this paper. 相似文献
20.
浸渍塑化杨木单板顺纹弯曲性能研究 总被引：1，自引：0，他引：1
本研究以酚醛树脂为浸渍液,杨木单板为木材试样,对经浸渍塑化处理的杨木单板进行三点弯曲试验,探索了木/竹复合层合板的组分材料--塑化杨木单板受不同压力时的顺纹弯曲弹性性能,并分析了其与塑化压力间的关系.结果表明,塑化杨木单板的静曲模量和静曲强度与塑化压力呈非线性关系.通过对杨木单板试验研究,为木材/竹材复合材料制造过程中的结构设计和生产工艺提供一定的理论依据和基本思路,并对产品的设计、组织现场生产和产品质量评估提供一定的参考. 相似文献