共查询到19条相似文献,搜索用时 406 毫秒
1.
聚丙烯比例对木塑复合材料性能的影响 总被引:3,自引:0,他引:3
通过正交试验,以木材纤维和废旧聚丙烯塑料为原料,异氰酸酯或马来酸酐作偶联剂,压制木材纤维/聚丙烯复合材料,研究聚丙烯(简称PP)用量对木塑复合材料性能的影响。结果表明,聚丙烯比例对复合材料的内结合强度、吸水厚度膨胀率、静曲强度和弹性模量有不同的影响。在热压时间、热压温度、复合材料密度相同的条件下,用异氰酸酯(简称MDI)作偶联剂,聚丙烯用量40%时复合材料的性能最佳;而用马来酸酐(简称MA)作偶联剂,聚丙烯用量50%时复合材料的性能最佳。 相似文献
2.
3.
聚丙烯与木纤维的复合研究 总被引:3,自引:1,他引:3
通过检测以木纤维和聚丙烯为原料制造的木塑复合材料的抗拉强度,研究了木纤维和聚丙烯的复合性能,并分析了木纤维与聚丙烯的质量比、马来酸酐改性聚丙烯及偶联剂对复合材料抗拉强度的影响.试验结果表明,当聚丙烯与木纤维的混合比为10∶3、偶联剂加入量约为聚丙烯质量的3%~5%时,木塑复合材料的抗拉性能最佳. 相似文献
4.
该文探讨了亚麻纤维对木材-聚丙烯(PP)复合材料力学性能的增强,尝试调节亚麻的添加量,对比亚麻纤维含量对复合材料的增强效果。并介绍了亚麻纤维增强木材-聚丙烯复合材料的挤出成型工艺流程。发现随着亚麻含量的增加,木材-聚丙烯复合材料的力学性能有先升后降的趋势,即亚麻纤维对木粉-聚丙烯复合材料有一定的增强效果;由本实验数据分析得出亚麻含量为50%时,复合材料的冲击强度、拉伸强度最大,亚麻含量为30%时,复合材料的弯曲强度最大。 相似文献
5.
6.
7.
8.
《林业工程学报》2017,(2)
采用模压和热压两种成型方法制备高木材纤维含量的聚丙烯(PP)基木塑复合材料,研究不同工艺方法和木材纤维质量分数(50%~90%)对木塑复合材料吸水性、接触角、表面自由能以及力学性能的影响,并通过扫描电子显微镜对复合材料的层间断面形貌进行观察。结果表明,木材纤维质量分数的提高使复合材料表面润湿性增强,力学性能有所下降,储能模量降低,玻璃化转变温度提高。当木材纤维质量分数达到80%时,复合材料仍可保持较好的弹性模量和冲击韧性;24 h吸水厚度膨胀率小于15%,可在潮湿环境下使用;表面自由能极性分量与中密度纤维板相当。扫描电镜结果表明,木材纤维质量分数增加可使复合材料的界面结合减弱。采用模压工艺制备的复合板材密度较大,抗弯性能较好;热压工艺所制复合板材的润湿性和冲击强度均优于模压工艺,在贴面装饰方面具有潜在优势。 相似文献
9.
10.
将竹纤维(BF)和聚己内酯(PCL)熔融共混模压制备竹纤维增强聚己内酯(BF/PCL)复合材料,采用硅烷偶联剂(KH560)做界面调控。结合力学、红外、扫描电镜及凝胶色谱等分析检测,确定最佳偶联剂用量和最佳模压温度。结果表明:偶联剂用量为1%(占纤维绝干重量)时,复合材料力学性能较佳,冲击、拉伸强度和断裂伸长率分别为13.72 kJ/m~2,12.71 MPa和6.28%;模压温度为90℃时,复合材料的冲击、拉伸强度及断裂伸长率分别达到15.02 kJ/m~2、14.21 MPa和7.21%,力学性能优良。 相似文献
11.
12.
YANG Wen-bin LI Jian LIU Yi-xing 《林业研究》2005,16(3):245-246
Three kinds of composites (fiber/Polypropylene, fiber/Polyethelene, and fiber/Polystyrene) were made by using hot pressing process for substrate of floorboard and the properties of each kind of composites were tested. MORs of PP/wood fiber, PS/fiber, and PE/fiber composites with coupling agent added were raised by 18.4%, 37.1%, and 42%. respectively, compared to those without coupling agent. Among the three kinds of fiber/plastic composites, fiber/PP composite has best mechanical properties, and it can meet quality standard of eligible grade product and come up to the excellent grade products of China when the coupling agent is added. The performance of composite made of PE/fiber or PS/fiber can exceed qualified product grade only with coupling agent added. 相似文献
13.
添加丙纶纤维及其改性处理对木塑复合材料性能的影响 总被引:3,自引:0,他引:3
就木塑纤维复合材料组分中添加丙纶纤维和对丙纶纤维进行改性预处理,改性剂的种类及改性剂的添加方式等引起材料物理力学性能和成网性能、模压性能的变化进行了研究。试验表明:添加丙纶纤维有助于改善材料的成网性能,使之成为具有良好模压性能的材料;对丙纶纤维进行改性的预处理可提高复合材料的物理力学性能;改性剂添加到木纤维中的工艺过程比对丙纶纤维进行预处理的工艺过程简单,并可以达到对丙纶纤维进行预处理的相同效果。 相似文献
14.
15.
热塑性聚合物之间的熔融共混改性和木材纤维与热塑性聚合物之间的复合,加入偶联剂均可提高复合材料的润湿性,对材料的相容有利;在偶联剂加入量相同的情况下,增加木材纤维的用量可以加速材料的润湿速度,有利于提高材料的润湿性;在热塑性聚合物用量一定的前提下,改变加入的增强材料的形状,对材料润湿性有影响,木材纤维可以提高复合材料的润湿性. 相似文献
16.
Rashmi Kumari Hirokazu Ito Masahiro Takatani Miho Uchiyama Tadashi Okamoto 《Journal of Wood Science》2007,53(6):470-480
Although wood/cellulose-plastic composites (WPC) of low wood/cellulose content have been more accepted worldwide and are promoted
as low-maintenance, high-durability building products, composites containing high wood/cellulose content are not yet developed
on an industrial scale. In this study, flow properties, mechanical properties, and water absorption properties of the compounds
of cellulose microfiber/polypropylene (PP) and maleic anhydride-grafted polypropylene (MAPP) were investigated to understand
effects of the high cellulose content and the dimensions of the cellulose microfiber. The molding processes studied included
compression, injection, and extrusion. It was found that fluidity is not only dependent on resin content but also on the dimension
of the filler; fluidity of the compound declined with increased fiber length with the same resin content. Dispersion of the
composite was monitored by charge-coupled device (CCD) microscope. Increasing the plastic content in the cellulose-plastic
formulation improved the strength of mold in addition to the bond development between resin and filler, and the tangle of
fibers. The processing mode affected the physicomechanical properties of the cellulosic plastic. Compression-molded samples
exhibited the lowest modulus of rupture (MOR) and modulus of elasticity (MOE) and the highest water absorption, while samples
that were injection-molded exhibited the highest MOR (70 MPa) and MOE (7 GPa) and low water absorption (2%). 相似文献
17.
Kouichi SETOYAMA 《中国林业科技(英文版)》2002,(4)
The effect of wood species (Chinese fir and Poplar), wood fiber content (10%, 25%, 40%) and wood fiber sizes (16 to 32 mesh, 32-65 mesh, above 65 mesh) on the properties of the wood fiber-Polypropylene composites were studied in this paper. The results indicate that the effect of wood fiber content and size in composite were more important than that of chosen wood species. Compared with polypropylene without wood fiber, the flexural strength of the composites increased when adding wood fiber into polypropylene, but the tensile and unnotched charpy impact strength decreased. And the above strength decreased with the wood fiber content increasing. When the wood fiber size becoming smaller (in higher mesh), the strength increased. In the comparison of wood species, the properties of composite using Chinese fir wood were better than that of Poplar, but not significant. The dynamic mechanical properties of the composites and PP were also tested and analyzed in this paper. 相似文献
18.
SEBS-g-MAH和原位接枝MAH对木粉/废旧塑料混合物复合材料力学性能的影响研究 总被引:1,自引:0,他引:1
由聚丙烯(PP)、高密度聚乙烯(HDPE)和聚苯乙烯(PS)组成的混合废旧塑料与木粉经高速混合机混合后,采用双螺杆/单螺杆串联挤出机组制备了木粉/混合废旧塑料复合材料。探讨了马来酸酐接枝苯乙烯-乙烯/丁烯-苯乙烯嵌段共聚物(SEBS-g-MAH)和原位接枝马来酸酐(MAH)对木粉/混合废旧塑料复合材料力学性能的影响。结果表明,与使用MAH和DCP的原位反应共混相比,SEBS-g-MAH显著提高了复合材料的抗冲击性能,但对拉伸和弯曲性能的改善不如原位反应共混显著。总的来说,混合废旧塑料制备的复合材料的力学性能要低于纯塑料混合物制备的复合材料,尤其是拉伸断裂伸长率。微观形态研究表明,添加SEBS-g-MAH和原位接枝MAH均可提高木粉与塑料混合物之间的界面相容性,但与添加SEBS-g-MAH相比,原位接枝MAH能更好的改善PP、HDPE、PS与木粉之间的界面结合。原位接枝MAH可被看作是一种改善木粉与塑料混合物间界面相容性的有效途径。此外,采用动态力学分析(DMA)进一步表征了复合材料的储能模量和阻尼因子。 相似文献
19.
QIN Te-fu HUANG Luo-hua LI Gai-yun 《林业研究》2005,16(3):241-244
对以铝酸酯为偶联剂对木粉进行表面改性处理后制备的木粉/聚丙烯复合材料的力学性能和形态学特征进行了研究。结果表明:铝酸酯偶联剂可以增加木塑复合材料的抗冲击强度,但会对复合材料的抗拉强度和抗弯强度造成负面的影响。对木塑复合材料的动态力学性能和微分扫描热量分析研究表明,以铝酸酯作为偶联剂,对木塑复合材料的储存模量和损失模量有少许增加,同时可降低材料的熔点和熔解热。利用扫描电镜观察木塑复合材料的木材与塑料界面发现,经铝酸酯处理过的木材与聚丙烯复合界面之间具有更好的相容性。这些研究结果表明,在木塑复合材料制造过程中利用廉价的铝酸酯作为木材化学改性剂,对改善复合材料的性质同样起作良好的作用。图6 表2 参16。 相似文献