共查询到20条相似文献，搜索用时 906 毫秒
1.
2.
胶合竹家具,如落地衣架和落地灯,存在着主杆节点的强度不足和美观度不佳等问题。植筋连接技术被广泛认为可以显著提升竹木构件节点的抗拔性能,而且由于其内置的特性,不会影响外形美观。尽管胶合竹植筋连接技术在建筑领域的方形梁柱节点中得到了广泛应用,但本研究旨在将这一技术应用于产品领域的胶合竹家具圆杆节点。在改变胶合竹植筋节点的形状后,需要通过试验分析来确定各项合理化设计参数,以提升节点的抗拔性能。选取胶合竹植筋圆杆为研究对象,以植筋边距、胶层厚度、植筋长径比等因素为研究变量。采用拉-拉模式进行抗拔性能试验,记录试件破坏模式和节点极限荷载。在试验过程中,出现胶合竹劈裂破坏、植筋拔出破坏和植筋屈服破坏3种破坏模式。研究结果表明：为防止胶合竹劈裂破坏,胶合竹与植筋直径之比应不小于8;节点极限荷载受胶层厚度影响显著,但胶层厚度不宜过大,当植筋直径为4 mm时,胶层厚度可设置为1.0～1.5 mm;节点极限荷载随着植筋长径比增加而提高,对于直径为4和8 mm的植筋杆,屈服破坏的临界植筋长径比均可取为15。基于试验结果,本研究提出了胶合竹植筋节点极限荷载预测方程,计算值与试验值较为接近。 相似文献
3.
胶合性能是胶合木制品的重要性能之一。在正交胶合木（CLT）中木材特征、胶黏剂性能以及木材与胶黏剂之间界面性能共同决定了正交胶合木的胶合性能。木材作为一种天然各向异性材料，其纹理方向不同，造成组坯方式对于胶合性能影响巨大。在胶合性能测试中，取样尺寸、取样形状对于胶合性能的测试结果都有一定的影响。胶合界面性能表征方面的研究正逐渐兴起，但是针对CLT胶合界面性能表征的相关研究报道并不多。有关CLT胶合的研究多集中在胶黏剂和胶合工艺方面，而针对不同锯材单元的特性对胶合性能尤其是耐久性影响的研究尚少有报道。文中基于现有研究对CLT胶合界面性能影响因素进行总结，梳理对比CLT胶合性能测试方法以及胶合界面性能表征技术，并对今后研究方向提出意见和建议。 相似文献
4.
为解决醛系合成树脂胶黏剂甲醛释放、热稳定性差和阻燃效果较差的难题,探讨了一种功能叠加型无机镁质胶黏剂的制备技术,以期替代醛类合成树脂胶黏剂在木材工业上的使用。本研究中镁质胶黏剂的优化配方为n(MgO)/n(MgCl_2)=6,n(H_2O)/n(MgCl_2)=16,胶合板制备工艺为施胶量700 g/m~2(双面),冷压时间28 h,养护时间15 d。试验结果显示,养护天数对镁质胶黏剂制备胶合板胶合强度的影响最显著。当养护天数为3～19 d时,胶合板的干、湿胶合强度均呈现先增大后下降的趋势,13 d时干、湿胶合强度均达到峰值,干、湿胶合强度分别为1.40和1.08 MPa。通过对胶合板剪切破坏界面进行扫描电镜观察发现,镁质胶黏剂渗透到木材孔隙中形成了胶钉,产生了机械咬合结构。利用热重分析仪和锥形量热仪等对镁质胶黏剂的热稳定性和燃烧性能进行了测试,结果表明,镁质胶黏剂在本研究温度范围(30～800℃)内的总质量损失率为48%。在50 k W/m~2的热辐射功率下,镁质胶黏剂制备胶合板的平均热释放速率(HRR)为35.84 k W/m~2,总热释放量(THR)为20.97MJ/m~2。与普通酚醛树脂胶黏剂相比,镁质胶黏剂具有较好的热稳定性和阻燃性能。 相似文献
5.
采用铜氨(胺)季铵盐(ACQ-D)防腐剂处理马尾松木材,以水性高分子异氰酸酯(API)、聚氨酯(PUR)和间苯二酚-苯酚-甲醛树脂(RPF)为胶黏剂制备防腐材胶合试样,研究胶黏剂种类和防腐剂处理浓度对马尾松胶合强度的影响。结果表明:API、PUR、RPF适用于ACQ处理马尾松的胶合,平均剪切强度和木破率均达到GB/T 26899—2011《结构用集成材》要求。胶黏剂种类对防腐材胶合强度有显著影响,表现为PUR和RPF的剪切强度优于API。与未处理材相比,ACQ处理对API胶合有负面影响,对PUR胶合有增强效应,对RPF胶合没有显著影响。在ACQ浓度为0.1%～1.0%范围内,胶合强度没有显著变化。 相似文献
6.
7.
为验证进口俄罗斯落叶松木材胶合性能,选用4种具代表性的结构用室温固化胶黏剂,根据GB/T 26899—2011《结构用集成材》进行胶合性能试验,对俄罗斯落叶松及胶黏剂的胶合性能进行分析研究。结果表明:对于俄罗斯落叶松,单组份聚氨酯、双组份聚氨酯和水性高分子异氰酸酯3种胶黏剂的胶层剪切强度和胶层剥离率均满足标准要求,其中双组份聚氨酯和水性高分子异氰酸酯胶黏剂胶合性能优异,单组份聚氨酯胶黏剂胶合性能良好;间苯二酚-甲醛树脂胶黏剂的胶合性能虽能达到标准要求,但不推荐作为结构用胶黏剂。 相似文献
8.
9.
10.
为实现木质旧家具在居家条件下的翻新改造,采用熨烫固化胶接方法用面料对桦木板表面进行饰面翻新,通过探究胶黏剂种类、熨烫温度和熨烫时间对面料翻新木材的胶合强度及耐水性的影响,得出理想的烫熨胶接工艺并将之用于木质旧家具的饰面翻新。结果表明:使用电熨斗的熨烫固化代替热压机的热压固化可实现居家条件下对木质家具的面料饰面翻新,胶黏剂种类、熨烫温度和熨烫时间对饰面翻新木材的胶合强度及耐水性有着重要影响;适当提高熨烫温度和延长熨烫时间可促进胶黏剂的固化进而确保胶合性能;在3种胶黏剂中最适于居家饰面翻新木质家具的胶黏剂为API胶黏剂。通过手工熨烫方法可实现对旧家具的个性化翻新,在避免家居审美疲劳的同时实现旧家具的再利用。 相似文献
11.
《Scandinavian Journal of Forest Research》2012,27(5):427-435
In Scandinavia, moose (Alces alces L.) sometimes cause severe browsing damage to economically-important pine. Moose-vehicle accidents have spurred construction of fences along roads, and these may interfere with moose migration between summer and winter ranges, or the road alone may be a barrier. If this happens and moose build up along roads, landowners may suffer economically. Therefore, this study investigated whether roads, fences or other factors influence the use of young pine stands by moose. Eighty stands along roads in northern Sweden were evaluated in which individually-browsed branches were counted on 9972 pines. Moose browsing was not significantly related to birch (Betula pendula Roth, B. pubescens Ehrh.) density, nor did it differ between pines (Pinus contorta Douglas or P. sylvestris L.). However, increased pine density, site productivity and proximity to a highway were associated with increased browsing. Further large-scale studies are needed to understand moose habitat selection and the effects of roads. 相似文献
12.
《Scandinavian Journal of Forest Research》2012,27(3):206-217
The root systems of 2-yr-old Picea glauca, Picea mariana and Pinus banksiana seedlings were submitted to various frost temperatures during an artificial frost to induce different levels of root damage. Frost-damaged and control seedlings were placed in a greenhouse under high and low soil moisture regimes. Seedling growth and physiology were evaluated periodically. Seedling survival was reduced when root damage reached levels of 60-80%. Root systems of all three species showed partial to total recovery by the end of the experiment. In general, root freezing damage caused reductions in seedling growth, with these reductions becoming less significant over time. Root damage had little to no effect on black spruce and jack pine seedling physiology, while white spruce CO 2 uptake decreased with increasing root damage. Shoot nitrogen content of all three species decreased slightly with increasing root damage. 相似文献
13.
Contour hedgerows of multipurpose tree species in the sloping tea lands of Sri Lanka are expected to reduce soil erosion and
also add significant amounts of plant nutrients to the soil via periodic prunings. The objective of this experiment was to characterize the biomass decomposition pattern and quantify the
amount of nutrients added through prunings of six tree species (Calliandra calothyrsus, Senna spectabilis, Euphatorium innulifolium, Flemingia congesta, Gliricidia sepium and Tithonia diversifolia) currently being used in hedgerows associated with tea. Withered leaf and stem prunings (50 g) were enclosed in 2-mm litter
bags, placed at 5-cm depth and retrieved after one, three, six, nine and 12 weeks. Loss of initial dry weight, N, P and K
was measured. Single exponential decay function adequately described both dry weight and nutrient loss. Tree species differed
significantly in their rate of breakdown with decomposition constants (k) varying from 0.0299 to 0.2006 week−1 for leaves and from 0.0225 to 0.0633 week−1 for stems. Gliricidia showed the highest k for leaves with the rest in the following descending order: Senna > Tithonia ≥ Euphatorium > Calliandra > Flemingia. A similar pattern was observed for loss of all nutrients with Calliandra and Flemingia always having lower k values than the rest. Although N immobilization was not observed, immobilization of P and K was observed
during the first week of incubation in some species, particularly in stem prunings. Annual biomass of prunings differed significantly
between tree species in the following descending order: Calliandra > Senna > Flemingia > Tithonia > Gliricidia > Euphatorium. Calliandra added the greatest amount of nutrients annually to the soil with Euphatorium adding the least. Calliandra prunings provided the annual total K requirement and 49% of the N requirement of mature tea. However, none of the species
provided more than 5% of the P requirement. It is concluded that among the tree species tested, Calliandra and Flemingia are the most suitable for contour hedgerows in tea plantations of this agroclimatic region because of their higher soil nutrient
enrichment capacity and slower decomposition rates which would minimize leaching losses.
This revised version was published online in June 2006 with corrections to the Cover Date. 相似文献
14.
《Scandinavian Journal of Forest Research》2012,27(1):53-61
This study investigated the stand structure in pine, spruce and deciduous forests in the border district of Finland and Russia. A total of 46 mature forest stands was selected as pairs, the members of each pair being as similar as possible with respect to their forest site type, age, moisture and topography. The stands were then compared between the two countries by means of basal areas and number of stems. The proportions of dominating tree species were 2-12% lower, and correspondingly the proportions of secondary tree species higher, in Russian forests. The density of the forest stock was also higher in each forest type in Russia. The forests in the two countries differed most radically in terms of the abundance of dead trees. The amount was two to four times higher in Russian deciduous and spruce forests, and in pine forests the difference was 10-fold. The stand structures indicated that Russian coniferous stands, in particular, were more heterogeneous than intensively managed pine and spruce stands in Finland. 相似文献
15.
《Scandinavian Journal of Forest Research》2012,27(1):15-27
The root collar diameter and the height:diameter ratio are of particular importance in container-grown seedlings where a high density in the containers may produce spindly seedlings. Temperature regimes and light quality are known to affect plant growth. The aim of this study was to identify responses in Picea abies (L.) Karst. seedlings grown with light providing different red:far-red ratios and under temperature regimes with alternating day (DT) and night temperature (NT) from negative (DT < NT) to positive (DT > NT) difference (DIF) between DT and NT. Experiments were conducted in controlled environment chambers and in a daylight phytotron. Only limited thermoperiodic responses appeared in P . abies seedlings with respect to seedling height and dry weight accumulation. The formation of terminal buds, however, was clearly delayed in seedlings grown at negative DIF. The results indicate a requirement for day extension light that is high in far-red, to prevent terminal bud formation under natural short-day conditions. An extended study should be conducted to clarify the minimum level of light intensity and the optimal light quality needed to prevent terminal bud formation under natural short-day conditions. 相似文献
16.
本文分析了CAD在设计中引起的正面和负面影响,并进行了系统的阐述,从而使设计者在应用中能够保持客观的态度。 相似文献
17.
Astra Zaluma Lauma Bruna Darta Klavina Natalija Burnevica Kristine Kenigsvalde Andis Lazdins Talis Gaitnieks 《Forest Pathology》2019,49(6)
Heterobasidion parviporum and Heterobasidion annosum are widely distributed root‐rot fungi that infect conifers throughout Europe. Infection of conifer stumps by spores of these pathogens can be controlled by treating fresh stumps with a competing non‐pathogenic fungus, Phlebiopsis gigantea. In this study, growth of three Latvian strains of P. gigantea and the biological control agent ‘Rotstop’ strain was evaluated in stem pieces of Norway spruce, Scots pine, lodgepole pine, Douglas‐fir, Weymouth pine, Siberian larch and Sitka spruce. The growth rates of one H. parviporum and one H. annosum isolate were also measured in the same stem pieces. The growth rate of P. gigantea varied greatly in wood of different conifer species. It was higher in the three pine species, lower in Norway spruce and lowest in Sitka spruce and Siberian larch, and in Douglas‐fir, this fungus did not grow. The largest area of wood occupied by P. gigantea was in lodgepole pine. Growth of Latvian isolates of P. gigantea in the wood of Pinus and Picea species was comparable to that of the Rotstop isolate. Consequently, stump treatment with local P. gigantea isolates should be recommended. However, our results suggest that Douglas‐fir stump treatment against Heterobasidion by P. gigantea may be ineffective and other stump treatment methods should be considered. 相似文献
18.
《Scandinavian Journal of Forest Research》2012,27(2):118-130
The effects of seed weight and seed type on seedling growth of Pinus sylvestris (L.) were studied by seeding individually weighed orchard and stand seed in different mixtures under harsh (direct seeding in field) and optimal (seeding in nursery) conditions. In the nursery experiment an increase in the seed weight from 3 to 7 mg increased the seedling height by 10-27% and total weight by 27-113%, and decreased the height/diameter ratio by 5-6% after 2 yrs. With elimination of seed weight effects, orchard seedlings were 2% taller than stand seedlings in year 2. Without elimination of seed weight effects, orchard seedlings were 7-13% taller. In the field experiment an increase in the seed weight from 3 to 7 mg increased seedling height by 18-65%, stem volume by 81-274% and the number of top-buds by 23-34% in year 5. After elimination of seed weight effects, orchard seedlings were 7-13% taller than stand seedlings and without elimination of seed weight effects 20-21% taller after 5 yrs. Even after elimination of both seed weight and genetic effects orchard seedlings were 3-9% larger than stand seedlings in the field experiment. In conclusion, the influence of seed weight and seed type on growth traits and slenderness is highly significant and the influence seems to be greater in harsh conditions. 相似文献
19.
Steven Maranz Amadou Niang Antoine Kalinganire Djeneba Konaté Bocary Kaya 《Agroforestry Systems》2008,72(3):231-239
Baobab leaves form an important part of the local diet in Sahel countries and elsewhere in Africa. Existing leaf nutritional
data and agroforestry performance information are based solely on Adansonia digitata L., the baobab of continental Africa. The introduction potential of Adansonia species from the center of diversity in Madagascar and from Australia remains untapped. To assess this potential, the mineral
contents and B1 and B2 vitamin levels of dried baobab leaves were determined for five-year old trees of A. digitata, A. gibbosa (A. Cunn.) Guymer ex D. Baum, A. rubrostipa Jum. & H. Perrier (syn. A. fony Baill.), A. perrieri Capuron and A. za Baill. grown in an introduction trial in Mali. Nutritional data were evaluated against survival and vigor to identify promising
germplasm. Leaf vitamin and crude protein contents were highest in the Madagascar species, especially A. rubrostipa (B1 88 mg 100 g−1, B2 187 mg 100 g−1, protein 20.7% dry weight). However, the local species far outperformed the introductions in survival, tree height, basal
diameter and resistance to termites. We suggest grafting as a way of harnessing the vigor of well-adapted local baobab varieties
to the superior nutritional profiles of A. rubrostipa and others. Cross-species grafting tests in Adansonia were successful, thus creating new agroforestry possibilities with different scion/rootstock combinations. 相似文献
20.
《Wood material science & engineering》2013,8(2):76-84
Abstract Wood in general and wooden studs in particular are often distorted owing to uneven shrinkage during the drying process in the sawmill. Twist is often the most detrimental of all types of distortion, and it is caused by spiral grain in combination with variations in moisture content. For sawmills, the objective is to produce dried, straight boards, and one method of dealing with boards with excessive spiral grain is to sort them out and then dry them in a pretwisted position to obtain straight boards after drying. A model using the finite element (FE) method for the simulation of drying twist distortions was first calibrated against laboratory experiments in which boards were dried with and without restraints and pretwists. After the calibration, the FE results were compared with industrial test results for boards that were dried without restraints or with restraints with zero pretwist, i.e. straight restraints. The FE model used an elastic–ideally plastic material model to obtain permanent deformations. The calibration was to set the yield stresses so that there was a good match between FE results and results from the laboratory experiments. The comparison between the industrial test results and the FE results showed that the FE model is capable of realistic simulations of drying boards with and without restraints and presumably also pretwists. 相似文献