共查询到20条相似文献，搜索用时 15 毫秒
1.
固体核磁共振法对低甲醛释放脲醛树脂化学结构的研究 总被引：1，自引：0，他引：1
在采用液体核磁对3种低甲醛释放脲醛树脂化学构造进行分析的基础上,利用13CCP/MASNMR对脲醛树脂固化产物的化学结构进行了研究.结果表明,不同固化体系下,3种低甲醛释放脲醛树脂胶黏剂的固化历程不同,固化后树脂的结构有所差别.不添加固化剂时,脲醛树脂的固化交联反应程度低,固化产物中羟甲基含量高,甲醛释放量也随之增加.加入固化剂后,促进了羟甲基的固化交联反应,脲醛树脂固化产物中羟甲基含量普遍降低.3种固化体系下,UF-3羟甲基含量最高;在氯化铵为固化剂的条件下,UF-2羟甲基含量最低,为0.0582;不添加固化剂和复合固化体系条件下,UF-1羟甲基含量最低,分别为0.0784和0.0713.不同固化体系对不同种类脲醛树脂的固化效果不同,固化后树脂的结构不同,其力学性能和甲醛释放能力也不同. 相似文献
2.
Influence of the melamine content in melamine-urea-formaldehyde resins on formaldehyde emission and cured resin structure 总被引：6，自引：0，他引：6
The effect of melamine content in melamine-urea-formaldehyde (MUF) resins on the formaldehyde emission and resin structure was investigated using six MUF resins synthesized with different F/(M + U) and M/U molar ratios. The formaldehyde emission from the plywood decreased as the F/(M + U) molar ratio decreased and the M/ U molar ratio increased. In addition, the bond performance was enhanced as the M/U molar ratio increased in the MUF resins with a fixed F/(M + U) molar ratio. Quantitative solution13C-NMR spectra of MUF resins revealed that the MUF resins with a high melamine content consisted of more highly branched crosslinkage structure and free melamine compared to the resins with low melamine contents. Furthermore, solid-state13C CP-MAS NMR spectra of cured MUF resins proved that more methylol groups, dimethylene ether, and branched methylene structures were present in the MUF resins with a higher F/(M + U) molar ratio, leading to increased bond strength and formaldehyde emission. There is no significant difference in the linkage structure of the cured resins with the same F/(M + U) and different M/U molar ratios except the ratios of carbonyl carbon of urea and triazine carbon of melamine. Therefore, the lower formaldehyde emission from cured MUF resins with a higher M/U molar ratio might be ascribed to the stronger linkages between triazine carbons of melamine than those of urea carbons. Consequently, the melamine contributed to strong crosslinking linkages in the cured resin structures, leading to lower formaldehyde emission and better bond performance.Part of this work was presented at the 48th Annual Meeting of the Japan Wood Research Society, Shizuoka, April 1998 相似文献
3.
4.
为了降低木材胶黏剂中的甲醛含量,减小胶合板甲醛释放对人体健康和环境造成的危害,采用乙二醛与单羟甲基脲(MMU)反应,合成了MMU与乙二醛物质的量之比分别为0.7∶1.0,0.9∶1.0,1.1∶1.0和1.3∶1.0的乙二醛?尿素?甲醛(GUF)共缩聚树脂;采用傅里叶变换红外光谱(FT?IR)和X射线衍射(XRD)对树脂的结构进行了表征,对树脂的基本性能、固化性能、润湿性能及胶合性能进行测定,并进行对比分析。结果表明,合成制备的GUF树脂稳定性较好,均超过了10 d;外观均为酒红色均一液体。MMU与乙二醛的物质的量之比对树脂固体含量和黏度有较大影响,固体含量随着物质的量之比增大而增大,当MMU与乙二醛物质的量之比为1.3∶1.0时,树脂的固体含量为63.12%;当MMU与乙二醛物质的量之比为0.9∶1.0时,树脂黏度的最小值为23.91 mPa·s。树脂的主要官能团(N—H、O—H、C??O、C—O—C和C—N)的红外吸收峰基本不受物质的量之比的影响。树脂对杨木单板的润湿性能良好,接触角为50.8°~57.3°;MMU与乙二醛的物质的量之比为1.3∶1.0时合成的GUF树脂性能较优,胶合板干状胶合强度和湿强度分别为1.81和1.47 MPa;低物质的量之比的GUF树脂固化后会出现晶体结构。 相似文献
5.
本文通过~(13)C NMR研究了脲醛树脂合成新工艺中不同反应阶段时的脲醛树脂的化学结构。研究结果表明脲醛树脂的化学结构主要受甲醛/尿素的摩尔比,pH值、反应温度和反应时间的影响。对脲醛树脂中主要的官能团:游离甲醛、亚甲基、亚甲基醚、Uron等相互关系也进行了研究。指出了生产低甲醛释放量,高力学性能刨花板用脲醛树脂中主要官能团的最佳含量。 相似文献
6.
低甲醛释放蔗渣中密度纤维板用脲醛树脂 总被引：6，自引：0，他引：6
以脲醛树脂结构形成特征为基础,研制了一种甲醛释放量低、内结合强度高的适用于蔗渣中密度纤维板生产的脲醛树脂胶粘剂。使用结果表明,所压制的蔗渣中密度纤维板物理力学性能达到国家标准要求,甲醛释放量可控制在２０ｍｇ／１００ｇ左右。 相似文献
7.
引入高分子量、高支化度以及端基为尿素的高支化聚脲(HBPU)用于低摩尔比脲醛树脂(UF)改性,利用HBPU与游离甲醛的反应以及与UF组分的共缩聚反应实现树脂耐水性能的提升和人造板甲醛释放量的降低,有效平衡胶合性能和甲醛释放量之间的矛盾。在无溶剂、无催化剂条件下,通过尿素(U)与三(2-氨基乙基)胺(TAEA)的脱氨缩合反应,一步合成了具有尿素端基的HBPU,并对HBPU的分子量分布和结构进行了表征。使用HBPU水溶液,采用UF合成反应后期加入和共混2种方法对UF进行改性,通过胶合板性能测试以及甲醛释放量测定,考察了HBPU添加量和添加方式的影响。凝胶渗透色谱和碳-13核磁共振分析表明,通过本研究的合成方法可以获得具有高分子量、高支化度、尿素为端基且水溶性良好的HBPU,并且随着U与TAEA摩尔比的提高,更多尿素封端产物形成。电喷雾电离质谱对改性树脂的分析结果表明,HBPU不仅与UF中的一部分游离甲醛发生羟甲基化反应,同时与UF组分反应生成了部分共缩聚产物。胶合板性能测试结果表明,共混以及反应后期加入HBPU两种方式得到的改性树脂耐水性能均显著提升。同时,使用添加5%HBPU改性树脂制备的胶合板甲醛释放量较未改性树脂制备胶合板降低41%。HBPU改性同步实现胶合性能的提升和甲醛释放量降低的主要原因在于HBPU在提高树脂支化程度的同时,还起到捕捉游离甲醛的作用。解决UF胶合性能和人造板甲醛释放量之间矛盾的关键在于提升树脂的支化程度,同时降低树脂中游离甲醛的含量,而引入高分子量、高支化度、具有类似尿素反应活性的聚合物是同步实现胶合性能提升和甲醛释放量降低的有效途径。 相似文献
8.
采用傅里叶变换红外光谱技术对由废弃刨花板制备的再生刨花中已固化脲醛树脂的分布及其活性进行了研究。结果表明，已固化的脲醛树脂主要分布在细刨花中，中粗刨花中极少存在，已固化的脲醛树脂仍有活性基因存在，并有助于再生刨花的再胶合及降低再生刨花板中的游离甲醛释放量。 相似文献
9.
用不脱水低摩尔脲醛树脂制造低游离甲醛刨花板与中密度纤维板 总被引：2，自引：0，他引：2
试验结果表明差示扫描量热仪 (DSC)能够测得NLFS - 1型捕捉剂与甲醛反应 ,并且这种捕捉剂能够捕捉脲醛树脂胶中的大部分游离甲醛 ,其捕捉量与树脂的摩尔比或游离甲醛量有关。对于低摩尔比 ,不脱水脲醛树脂刨花板和中密度纤维板 ,仅用 5 %捕捉剂就能获得较高的捕捉能力。这些板的游离甲醛释放量均能达到欧洲E1级或国标GB -T11718- 1999A级标准。刨花板后期热处理 ,对板的内结合强度提高明显 ,但板的甲醛释放量略有增加 相似文献
10.
Stefan Pinkl Hendrikus W. G. van Herwijnen Stefan Veigel Wolfgang Gindl-Altmutter Martin Riegler 《Journal of Wood Science》2018,64(4):390-397
Urea formaldehyde (UF) resins are important for wood industry due to their attractive properties at reasonable price. Particulate fillers added to UF are of interest with regard to improving the functionality of UF and also in terms of reduced UF consumption. To study their potential as filler, solid UF microspheres were synthesized and characterised respecting its morphology, chemical curing and thermal stability. Marigold flower structured spheres with diameters between 5 and 20 µm are presented and application trials demonstrated that high amounts of UF may be replaced by solid microspheres without impairing adhesive bond strength of solid wood bond lines. Fluorescence microscopy showed that microspheres greatly reduce adhesive penetration into the wood substrate, retaining the modified adhesive in the bondline. UF microspheres may thus be considered as viable filler for UF adhesives, particularly with regard to the possibility of endowing them with added functionality like self-healing properties. 相似文献
11.
低毒脲醛树脂固化物的甲醛释放 总被引：4，自引：1，他引：4
对不同固化体系下三种低毒脲醛树脂固化物随环境变化的甲醛释放量进行了具体研究。试验结果表明:固化体系不同,脲醛树脂的甲醛释放量有很大差别。随着温度的升高,甲醛释放量明显增加;随着时间的变化,脲醛树脂固化物的甲醛释放量逐渐减少,第5天以后逐渐趋于稳定。用三聚氰胺进行改性的脲醛树脂的甲醛释放量明显低于未加任何改性剂的脲醛树脂。 相似文献
12.
13.
In order to understand the impact of formaldehyde/urea (F/U) mole ratio on penetration characteristics of urea–formaldehyde (UF) resin into softwood tissues, a quantitative measurement of UF resin penetration into radiata pine (Pinus radiata) tissues from the bond-line was undertaken. Four different F/U mole ratios (1.6, 1.4, 1.2, and 1.0) of UF resins with different viscosities and two levels of hardener (NH4Cl) for two extreme F/U mole ratios (1.6 and 1.0) were studied. Firstly, field emission scanning electron microscope and confocal laser scanning microscopy were used to localize UF resins in the bond-line for the qualitative evaluation of resin penetration. Then light microscopy was employed to quantitatively measure the resin penetration and bond-line thickness. A decrease in the F/U mole ratio of UF resin that proportionately decreased the resin viscosity resulted in an increase in the average resin penetration and a decrease in the bond-line thickness. Higher hardener level provided a greater resin penetration with all F/U mole ratio UF resins. These results demonstrated that F/U mole ratio had an impact on the penetration and bond-line thickness of UF resins, owing to differences in the reactivity of resins, with higher F/U mole ratio resins being more reactive. 相似文献
14.
中国黑荆单宁与羟甲基反应动力学的研究 总被引：1，自引：0，他引：1
用动态ＤＳＣ研究中国黑荆单宁与活性酚醛树脂中羟甲基的反应动力学过程，分别测定了不同升温速率和不同摩尔比的活性酚醛树脂的反应动力学常数，发现上述两种因素对反应动力学常数均有一定的影响。 相似文献
15.
The thermo-oxidative degradation of various polyol-added isocyanate resins for wood adhesives was studied using differential scanning calorimetry and thermogravimetry. The degradation of the resin cured with water began at 150°C. When a certain polyol was added to the resin at an NCO/OH ratio of 25 in addition to water, the cured resin began to degrade at 200°C. To clarify the cause of the good thermal stability in polyol-added resins, the effect of various polyols on the reactivity of isocyanate was investigated. It was found that the reactivity of isocyanate was enhanced by the addition of a dipropylene glycol and glycerin-type polyols. In addition, the effect of the NCO/ polyol-OH ratio was investigated using dipropylene glycoltype polyol. The reactivity of isocyanate increased with increasing polyol content. The thermal stability of the resin was improved to a certain degree by addition of a small amount of the polyol but deteriorated when a large amount of the polyol was added.Part of this paper was presented at the 48th annual meeting of the Japan Wood Research Society, Shizuoka, April 1998 相似文献
16.
Durability of isocyanate resin adhesives for wood I: Thermal properties of isocyanate resin cured with water 总被引：1，自引：0，他引：1
The thermal properties of isocyanate (IC) resin cured with water were studied using dynamic mechanical analysis (DMA) and Fourier transform infrared spectroscopy. The thermal properties of cured phenol formaldehyde (PF) resin were also studied for comparison purposes. The DMA specimens were prepared using a unique technique. The relation between the mechanical and chemical changes of the resin during DMA was clarified. The cured PF resin had better thermal stability than the IC resin cured with water. The improvement of thermal stability in cured IC resin by heat treatment was considered to be less effective. The effect of the heating rate on the mechanical properties was also investigated. The apparent activation energy in the thermal degradation of cured IC resin was calculated based on the results obtained.Part of this paper was presented at the 47th Annual Meeting of the Japan Wood Research Society, Kochi, April 1997 相似文献
17.
三聚氰胺改性低毒脲醛树脂耐水性研究 总被引：1，自引：0，他引：1
不同摩尔比的两类低毒脲醛树脂(JQ21未改性,JQ22与5%三聚氰胺共聚),分别与不同质量比的三聚氰胺树脂混合,并在不同的固化体系中固化,用于胶合板的压制.对胶合板的胶合性能及甲醛释放量进行了研究.实验结果表明:固化体系不同,胶接强度也不相同;随着摩尔比的增加,胶接强度提高,甲醛释放量亦相应提高;同时采用共聚和共混两种方法进行改性的脲醛树脂,其胶接强度和甲醛释放量均优于单一的采用共混改性的脲醛树脂;并且混合胶液中三聚氰胺的比例越低,胶接性能越筹,甲醛释放量变化逐渐趋于平稳. 相似文献
18.
For manufacturing low-formaldehyde emission particleboard from wheat straw and urea-formaldehyde (UF) resins using urea treatment for indoor environments, we investigated the influence of urea treatment on the formaldehyde emission, physical and mechanical properties of the manufactured particleboard. Wheat straws were treated at three levels of urea concentration (5%, 10%, 15%) and 95℃as holding temperature. Wheat straw particleboards were manufactured using hotpress at 180℃and 3 MPa with two types of UF adhesive (UF-45,UF-91). Then the formaldehyde emission values, physical properties and mechanical properties were considered. The results show that the formaldehyde emission value was decreased by increasing urea concentration. Furthermore, the results indicate that the specimens under urea treatment have better mechanical and physical properties compared with control specimens. Also specimens under urea treatment at 10% concentration and UF-91 type adhesive have the most optimum physical and mechanical strength. 相似文献
19.
稻草中密度纤维板用改性脲醛树脂的研究 总被引：2，自引：2，他引：2
对比三聚氰胺、二甲基硅油、硅树脂和偶联剂KH-550四种改性剂改性的脲醛(UF)树脂性能的差别及其对稻草中密度纤维板性能的影响,并进行经济评价,最终确定适用于稻草纤维板的改性UF树脂的工艺条件,同时借助于红外光谱(FT-IR)和差热扫描分析(DSC)研究最佳改性UF树脂的结构和固化特性.结果表明,三聚氰胺改性脲醛(MUF)树脂不论是对树脂性能、板性能改善还是从成本分析方面均为稻草纤维板最佳的胶黏剂,FT-IR显示出与未加三聚氰胺相比,加入三聚氰胺后树脂的羟甲基含量降低了10 %,DSC分析则表明其峰值温度有较大幅度的提高,但放出的热量较少.加入三聚氰胺改性的UF树脂其表面张力变小. 相似文献
20.
在实验室制备得到树脂型甲醛捕捉剂,考察了甲醛捕捉剂与不同F/U摩尔比脲醛树脂混合使用后制备得到的刨花板力学性能及甲醛释放量。研究结果表明,甲醛捕捉剂的添加能有效降低刨花板的甲醛释放量,但对混合树脂的最终力学强度性能不利。混合树脂的摩尔比F/U是决定相关刨花板力学性能及甲醛释放量的主要因素。当与摩尔比F/U=1的脲醛树脂混合使用时,添加占总施胶量5%甲醛捕捉剂的刨花板甲醛释放量可达到E1级,同时,内结合强度值满足室内级国家标准要求。与摩尔比F/U=1.2的脲醛树脂混合使用,当甲醛捕捉剂的添加量为20%时,刨花板性能达标。 相似文献