首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 703 毫秒
1.
The natural resistance of Erythrophleum fordii Oliver wood to degradation by Phanerochaete sordida and Phanerochaete chrysosporium white-rot fungi was investigated. In this study, Fagus crenata Blume (Japanese beech) was selected as reference species. The results showed that both fungi caused less than 2% mass loss in E. fordii wood, while the degradation of beech wood produced by P. chrysosporium and P. sordida was approximately 12 and 14%, respectively. Microscopic observations revealed high structural rigidity of E. fordii timber. Hyphae were only observed in the lumen of vessels and parenchymal cells, while the fibers were not affected. The E. fordii wood fiber consisted of highly lignified thick-walled fibers with the fiber lumina almost completely closed. Two-dimensional heteronuclear single-quantum coherence nuclear magnetic resonance evaluation revealed the E. fordii wood to have a highly condensed-lignin structure that reflected by the durability classes. These unique parameters are likely to be critical for the high natural resistance of E. fordii.  相似文献   

2.
Elm (Ulmus, Ulmaceae) is one of the most popular and important trees in urban and landscape areas in Iran. A severe decline of elm trees has recently been observed in some areas of Kerman and Shiraz cities. However, the identity of the causal agents has not yet been investigated. The purpose of this study, carried out in the years 2012–2014, was to isolate and identify fungal trunk pathogens associated with decline symptoms observed in elm trees. Samples were collected from trunks and branches of trees showing various disease symptoms and internal wood lesions. Fungal isolations were made from discolored or decayed wood tissue. In Kerman some elm trees were attacked by the beetle Aeolesthes sarta; therefore, samples were also collected from larvae and adults of beetles associated with trees showing wood damage. Fungal isolates were identified by morphological, cultural and molecular characteristics. Thirteen fungal species, Phaeoacremonium (P.) minimum, P. parasiticum, P. sicilianum, P. alvesii, P. fraxinopennsylvanicum, Spencermartinsia viticola, Dothiorella (Do.) sarmentorum, Neoscytalidium hyalinum, Diatrype (Di.) whitmanensis, Cosmospora viridescens, Phoma (Pho.) herbarum, Phellinus (Phe.) tuberculosus and Inonotus levis were identified. Phaeoacremonium parasiticum was the only species isolated from both larvae and adult beetles. Pathogenicity trials were performed on detached shoots of elm under greenhouse conditions. Dothiorella sarmentorum was the most virulent species based on the length of wood necrosis. This study is the first report of P. sicilianum, C. viridescens and Phe. tuberculosus in Iran. In addition, most of the isolated species are reported for the first time on elm trees in the world.  相似文献   

3.
Niche differentiation, in terms of time and space, has been reported within a community of ambrosia beetles (Coleoptera: Scolytidae and Platypodidae) in a tree trunk. Two platypodid ambrosia beetles, Platypus quercivorus (Murray) and Platypus calamus Blandford, utilize a similar height range with respect to the Quercus serrata Murray (Fagaceae) trunk. The sapwood and heartwood (i.e., wood types) are known to differ in their physical and chemical characteristics. The objective of this study was to determine the differences among ambrosia beetles, in terms of wood type preferences, in a Q. serrata tree trunk. We analyzed the horizontal distribution patterns of ambrosia beetles within two mature Q. serrata tree trunks. Platypus calamus and the other ambrosia beetles [P. quercivorus, Ambrosiodmus lewisi (Blandford), Ambrosiophilus atratus Eichhoff, and Xyleborus sp.] showed different horizontal distribution patterns within the wood. The former tended to utilize the heartwood, whereas the latter utilized the sapwood. These results suggest that the wood type can be regarded as one of the niche dimensions of ambrosia beetles in a Q. serrata trunk.  相似文献   

4.
Non-woody biomass species have high-energy potentials, which could be used for bioenergy production. Invasive species are species spreading into areas, where they are not native, consequently causing environmental and economic problems. Therefore, the present study evaluated the proximate, ultimate, chemical, and fuel characteristics of wood and charcoal of three invasive non-forest tree species in Saudi Arabia: Calotropis procera, Rhazya stricta, and Phragmites australis, which were compared with the wood of Acacia tortilis, a preferable local fuelwood. All these data were discussed to investigate the possibility of using the invasive plants for energy production. The thermal behavior of wood was analyzed using thermo-gravimetric and derivative thermo-gravimetric methods. Overall, compared with the wood of A. tortilis, the woods of R. stricta and P. australis are suitable for energy production. The charcoal produced from P. australis emitted less nitrogen (N) oxide than that of R. stricta.  相似文献   

5.

Context and aim

This study aimed to examine the effect of the tension wood G‐layer on the viscoelastic properties of wood.

Methods

Tension wood and opposite wood samples were obtained from six French Guianese tropical rainforest species (Sextonia rubra, Ocotea guyanensis, Inga alba, Tachigali melinoni, Iyranthera sagotiana and Virola michelii); the tension wood of the former three of these species had a G‐layer, whilst the tension wood from the latter three had no G‐layer. Tensile dynamic mechanical analysis (DMA) was performed on green never dried wood samples in the longitudinal direction with samples submerged in a water bath at a temperature (30°C) and frequency (1 Hz) representative of the conditions experienced by wood within a living tree. Then, DMA was repeated with samples conditioned to an air-dried state. Finally, samples were oven-dried to measure longitudinal shrinkage.

Results

Tension wood did not always have a higher longitudinal storage (elastic) modulus than opposite wood from the same tree regardless of the presence or absence of a G‐layer. For the species containing a G‐layer, tension wood had a higher damping coefficient and experienced a greater longitudinal shrinkage upon drying than opposite wood from the same species. No difference was found in damping coefficients between tension wood and opposite wood for the species that had no G‐layer.

Conclusion

It is proposed that the different molecular composition of the G-layer matrix has an influence on the viscoelasticity of wood, even if a biomechanical gain is not yet clear. This study shows that rheological properties and longitudinal shrinkage can be used to detect the presence of a G‐layer in tension wood.
  相似文献   

6.
Within-stem variations in the mechanical properties of 17–19-year-old Melia azedarach planted in two sites in northern Vietnam were examined by destructive and nondestructive methods. Wood samples were collected from 10, 50, and 90% of the radial length from pith on both sides (North and South) at 0.3, 1.3, 3.3, 5.3, and 7.3 m heights above the ground. The mean values in whole trees of wood density (WD), modulus of rupture (MOR), modulus of elasticity (MOE), and dynamic modulus of elasticity (Ed) at 12% moisture content were 0.51 g/cm3, 78.58 MPa, 9.26 GPa, and 10.93 GPa, respectively. Within the stem, the radial position was a highly (p?<?0.001) significant source of variation in mechanical properties. MOR, MOE, and Ed increased from pith to bark. WD had a strong positive linear relationship with both MOR (r?=?0.85, p?<?0.001) and MOE (r?=?0.73, p?<?0.001). This suggests that it is potentially possible to improve mechanical properties through controlling WD. MOR had also a strong linear relationship with Ed (r?=?0.84, p?<?0.001). This indicates that Ed is a good indicator to predicting the strength of wood if the density of measured element is known. Besides, the stress wave method used in this study provides relatively accurate information for determining the stiffness of Melia azedarach planted in northern Vietnam.  相似文献   

7.
The influence of moisture content (MC) on the orthotropic viscoelasticity of Chinese fir wood (Cunninghamia lanceolata [Lamb.] Hook.) has been examined in low temperature environment. Storage modulus E′ and loss modulus E″ of wood with six different levels of MC ranging from 0.6 to 22.0% were determined from ??120 to 40 °C and at multi-frequency range of 0.5, 1, 2, 5, and 10 Hz using a TA instruments® Dynamic Mechanical Analyzer (DMA 2980). The results showed that a distinct moisture dependency is exhibited by the orthotropic viscoelastic behaviour of Chinese fir wood. With the exception of some apparent activation energy (ΔE) for β-relaxation process, the E′ decreased and the E″ peak temperatures moved towards lower temperature and the ΔE for α-relaxation process became lower with MC increasing in all orthotropic directions, whereby individual decline of E′ and the E″ peak temperatures were affected by MC to different degrees. Besides, a little E″ peak at around 0 °C was only seen in L direction, which could be attributed to the melting of frozen water. Furthermore, the dynamic viscoelastic behavior of wood is also dependent on the measurement frequency. The findings suggest that the orthotropic structure and moisture content have an important influence on the viscoelastic performance in low temperature environment.  相似文献   

8.
We evaluated the antifungal and antitermite activities of wood vinegars produced from oil palm trunk. The wood vinegars were produced at three different pyrolysis temperatures, 350, 400, and 450 °C. Antifungal activities of vinegars were evaluated using a Petri dish bioassay with 0.5, 1.0, and 1.5% (v/v) against a white-rot fungus, Trametes versicolor, and a brown-rot fungus, Fomitopsis palustris. Antitermite activities were tested using a no-choice bioassay method for Coptotermes formosanus with 2.5, 5.0, 7.5, and 10.0% (v/v). All the wood vinegars exhibited antifungal activities against T. versicolor. In particular, the wood vinegar produced at 350 °C resulted in complete inhibition of T. versicolor growth at 1.0 and 1.5%. However, higher concentrations were required to obtain growth inhibition of F. palustris. All the wood vinegars exhibited antitermite activity to C. formosanus workers in the no-choice experiment at relatively high concentrations. For instance, 10% concentration was required to achieve 100% mortality against C. formosanus at all production temperatures. The lowest mass loss of the treated filter paper of 11.75% was obtained with a 350 °C—10.0% combination.  相似文献   

9.
In this article, the conservation of archaeological waterlogged wood (WW) of Afzelia sp. (medium degraded: Umax = 385%) was impregnated in vacuum with an aqueous solution of acrylic acid (AA), sodium acrylate monomer (AANa), crosslinking agent (MBA) and catalyst (V-501). The simultaneous in situ polymerization and crosslinking resulted in slightly crosslinked sodium polyacrylate (PAANa) in the wood structure. The results showed that untreated WW had only a very limited ability to re-swell to recover its original dimensions from a collapsed condition, while WW protected by crosslinked PAANa could almost fully recover its original shape and size even after several drying–rewetting cycles. From microscopic observations, treated wood was found to maintain its original cell structure, form and shape even after repeated drying–rewetting cycles. PAANa was observed to be densely localized near the middle lamella, the cell corners, and the cell lumina by transmission electron microscopy observation. These observations suggest that our PAANa treatment provides reasonable strength as well as favorable hydrophilicity to avoid hornification of the cell wall upon drying, thus providing unique shape recovery properties.  相似文献   

10.
Many reports have been published about designing the strength of glulam using simulation methods. In simulation methods, one of the most important problems is how to deal with correlations among strength factors, i.e., modulus of elasticity (MOE), modulus of rupture (MOR), tensile strength (σT), and compression strength (σC). For example, in the case that the MOR criteria of glulam is σ ni /f ni + σ bi /f bi ≥ 1 (where σ ni and σ bi are the axial stress and the bending stress of the i-th lamina respectively, and f ni and f bi are the axial strength and the bending strength of the i-th lamina respectively), a correlation between f ni and f bi exists. How can we account for this correlation when calculating the strength of glulam, bearing in mind that it is very difficult to measure the correlation coefficients among MOR, σT, and σC? We developed a method by which these problems could be solved, and, using random variables generated by this method, the strengths of glulam were simulated. The simulated values were almost the same as the experimental values. The results indicated the usefulness of the method.  相似文献   

11.
This study quantified variations within tree stems in tangential shrinkage (αT), radial shrinkage (αR), and tangential/radial shrinkage ratio (αT/αR) of Melia azedarach grown in two different sites in northern Vietnam. The overall values of αT, αR, and αT/αR were 7.05%, 4.38%, and 1.64, respectively. The variation pattern in αT and αR was found to increase gradually from pith to bark and this trend was similar on both sites. In radial direction, the αT/αR decreased significantly from 10 to 50% of the radial length from pith before approaching a constant value toward the outside. The transverse shrinkage variation with height was very small and without statistical significance. There were strong positive relationships between transverse shrinkage and basic density (BD). This implies that the selection for high wood density may lead to increase wood transverse shrinkage. In addition, the αT and αR had significant positive linear relationships with both acoustic wave velocity (VL) and dynamic modulus of elasticity of log (DMOElog). This result suggests that it might be possible to sort lumber with large transverse shrinkage by stress wave method for M. azedarach planted in northern Vietnam.  相似文献   

12.
In this study, to summarize the changes of thermal-softening behaviors of wood and acetylated wood due to differences in the kinds of swelling liquids, the following measurements were conducted. Untreated and acetylated wood samples were swollen by various liquids and the temperature dependences of the dynamic viscoelastic properties were measured after the heating and cooling histories were unified among the samples. The results obtained are as follows. Untreated samples swollen by high-polarity liquid had lower peak temperature of tanδ, however acetylated samples had higher peak temperature of tanδ than those of untreated wood. On the other hand, untreated wood samples swollen by low-polarity liquid had higher peak temperature of tanδ, however acetylated samples had lower peak temperature of tanδ than those of untreated wood. The amount of swelling is determined by interaction between wood and liquid due to proton-accepting power and molar volumes of liquid and so on, therefore the peak temperature of tanδ and degree of reduction in dynamic elastic modulus (E´) with increasing temperature were corresponded to the amount of swelling.  相似文献   

13.
Four strains of the termite mushroom Termitomyces eurrhizus collected in Japan were surveyed for their wood decaying properties in three softwood and two hardwood species, in comparison with the white-rot fungus Trametes versicolor and the brown-rot fungus Fomitopsis palustris. All strains of T. eurrhizus degraded only the surfaces of the wood samples, and differences in mass-loss rates between heartwood and sapwood were generally not significant. Higher mass-loss rates were generally obtained in softwood than in hardwood. The results of chemical analyses of decayed wood samples indicated that T. eurrhizus does not have high lignin-degradation ability, even though it is categorized as a white-rot fungus. These results clearly suggest the unique physiological characteristics of T. eurrhizus.  相似文献   

14.
The selection of wood species and the styles of sculpture play key roles in the characterization of Buddhist statues. After Jianzhen, a Chinese Buddhist monk, visited Japan in the mid-eighth century, wood of the genus Torreya had been frequently used to produce single-bole statues. Establishing measures for the accurate identification of wood in the genus Torreya is effective for investigating the drastic change in the production of statues during this period. Analyzing the plastid deoxyribonucleic acid (DNA) fragments extracted from wood is considered helpful in the identification of species in the same genus. This study analyzed the sequences and residual amounts of plastid DNA fragments in the wood of Torreya nucifera. Nucleotide substitutions in the plastid DNA were clearly identified between T. nucifera and the species distributed in China, indicating that the wood of Torreya sp. can be discriminated based on the plastid DNA sequences. DNA polymorphism analyses revealed sequence diversity for the intergenic spacers on the T. nucifera plastid DNA. A series of polymerase chain reaction (PCR) analyses demonstrated that the plastid DNA fragments with a length of approximately 100 bp could be amplified from the residual DNA extracted from the T. nucifera sapwood with longer elapsed years after cutting. Therefore, an identification of wood species in the genus Torreya based on their plastid DNA is considered to be one of the most effective measures taken in the study regarding the historical changes of Buddhist statues.  相似文献   

15.

Key message

The radial wood growth curves of Cinnamomum kanehirae Hayata (an endangered species of subtropical Taiwan) exhibit an S shape. The dominant trees displayed a larger radial growth than the codominant trees, and their growth was more sensitive to air temperature.

Context

Knowledge of wood radial growth is important for evaluating the factors that limit tree growth performance. The relevant experiments have mostly been conducted in cold and temperate ecosystems, but rarely in subtropical ecosystems.

Aims

In this study, we aimed to construct a unified radial growth model for Cinnamomum kanehirae Hayata and to identify its sensitivity to temperature.

Methods

The wood radial increments were quantified for 3 years by either pinning or microcoring. The radial wood growth curves were modelled integratively by semiparametric regression and individually by curve fitting. The effects of tree social class, interannual and environmental factors on radial growth were analysed quantitatively.

Results

A unified S-shaped growth model for C. kanehirae was successfully constructed. By including the social class effect, the model was significantly improved. The maximum radial increment (A) was significantly correlated with the maximum growth rate (μ); both A and μ were significantly higher in dominant than in codominant trees. The time-varying radial growth rate was more sensitive to air temperature in dominant than in codominant trees.

Conclusion

Semiparametric models revealed an S-shaped growth curve of C. kanehirae and confirmed the higher temperature sensitivity of dominant trees compared to codominant trees in humid subtropical areas.
  相似文献   

16.
Transmittance and reflectance of visible light by sugi wood (Cryptomeria japonica) were investigated in the longitudinal (L) and tangential (T) directions. Transmittance was the highest in the L direction and reflectance was the highest in the T direction, suggesting that structural anisotropy influences transmittance and reflectance. Intra-ring variations observed with a microspectrometer indicated that T transmittance was higher for latewood than for earlywood, but there was no such trend in for L transmittance in which the highest levels occurred near the annual ring boundaries, on either the earlywood or latewood side, and the lowest at the transition from earlywood to latewood. Dependence of L transmittance on wavelength also showed variations according to the intra-ring position. The increasing of transmittance of earlywood at wavelengths?<?500 nm with increasing wavelength was observed, but this was not confirmed for latewood because of absorption by lignin. These observations supported a previously published finding, which was based on measurements in the radial direction, that the number of internal cell wall reflections, rather than density, determines wood lightness. Indeed, in the L direction, most of the incident light passes through lumens in earlywood and through cell walls in latewood, while it is subjected to numerous internal reflections at the interface between lumens and cell walls. This was further confirmed by the transmittance of earlywood being greatly decreased by radial compression.  相似文献   

17.
Heterotrophic components of biofilms on wood artefacts were studied at the Conservation Laboratory for Wood Artefacts of the University Suor Orsola Benincasa of Naples, Italy. The aim of the study was to add new information on the micro-habitats represented by biofilms formed by wood-dwelling organisms. Light and electron microscopy of histological features of woods used to make the artefacts showed that the woods belonged to species of lime (Tilia sp.), poplar (Populus sp.) and pear (Pyrus sp.). A Denaturing Gradient Gel Electrophoresis analysis performed on heterotrophic microorganisms colonizing the artefacts led to identify four species of bacteria, namely Bacillus cereus, B. mycoides, B. subtilis and Microbacterium oleivorans, and seven species of fungi, namely Alternaria alternata, Aspergillus fumigans, A. versicolor, Cladosporium cladosporioides, C. oxysporum, Fusarium oxysporum and Penicillium chrysogenum. Based on its morphological features, an insect found on some artefacts was identified as the xylophagous beetle Nicobium castaneum (Anobiidae). The influence of wood type and environmental conditions on the diversity of microorganisms was discussed.  相似文献   

18.
  • ? It is essential to understand how characteristics are related to each other in breeding programmes to select wood properties, in order to avoid that, in selecting for one trait, we are negatively affecting another. Moreover, measuring wood properties is time consuming and expensive.
  • ? This study assesses genetic and phenotypic correlations between wood density components and spiral grain of 46 half-sib families of Pinus pinaster in seventeen-year-old trees.
  • ? Results showed that genetic correlations for all wood density components were higher than corresponding phenotypic correlations. Furthermore, all wood density components were highly genetically correlated with ring density, and also closely associated among themselves. Results showed a higher genetic correlation of ring density with earlywood density (r g = 0.96) than with latewood density r g = 0.79). A moderate to high positive genetic correlation was found between spiral grain and wood density characteristics (0.29–0.61).
  • ? We conclude that ring density (overall wood density) can be improved by increasing either earlywood density, latewood percent, or both of these traits, and spiral grain can be modify in future plantations.
  相似文献   

19.
As a consequence of the recent introduction of the pine wood nematode Bursaphelenchus xylophilus in Portugal, nematodes of the genus Bursaphelenchus were looked for in various French pine forests, in trees attacked by Monochamus galloprovincialis, the vector insect of B. xylophilus, and in the insects themselves. Trap trees were felled in 12 localities distributed all over the country. Nematodes were extracted from transversal stem discs; insects emerging from the trap trees were studied. B. hellenicus, B. leoni, B. mucronatus and B. sexdentati were isolated, but not B. xylophilus. The presence of B. mucronatus and the absence of B. xylophilus were confirmed by molecular markers. B. mucronatus was isolated from several regions with an average prevalence of 19%. The infestation of M. galloprovincialis by B. mucronatus reached 26.7%. The wide distribution of B. mucronatus in France could have an effect on the extension of B. xylophilus in a case of an introduction.  相似文献   

20.

? Key message

Intensive measurements of basic specific gravity and relative water content of lumens show that within-stem variations strongly depend on species and cannot be summarised through the typical patterns reported in the literature; breast height measurements are not always representative of the whole stem.

? Context

Knowledge of the distribution of wood properties within the tree is essential for understanding tree physiology as well as for biomass estimations and for assessing the quality of wood products.

? Aims

The radial and vertical variations of basic specific gravity (BSG) and relative water content of lumens (RWC L ) were studied for five species: Quercus petraea/robur, Fagus sylvatica, Acer pseudoplatanus, Abies alba and Pseudotsuga menziesii. The observations were compared with typical patterns of variations reported in the literature.

? Methods

Wood discs were sampled regularly along tree stems and X-rayed in their fresh and oven-dry states.

? Results

At breast height, BSG was found to clearly increase radially (pith to bark) for two species and to decrease for one species. For F. sylvatica and A. alba, the radial variations of BSG were rather U-shaped, with in particular inner wood areas showing respectively lower and higher BSG than the corresponding mature wood. RWC L increased generally from inner to outer area but wet sapwood was clearly distinguishable only for the coniferous species. Vertical variations of BSG and RWC L were strongly dependant on the species with usually non-linear patterns.

? Conclusion

The observed variations of BSG were only partially in agreement with the reported typical radial patterns. Despite the vertical variations, the mean BSG of a cross-section at breast height appeared to be a good estimator of the mean BSG of the whole stem (although the difference was statistically significant for coniferous species), whereas breast height measurement of RWC L was not representative of the whole stem.
  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号