共查询到19条相似文献，搜索用时 687 毫秒
1.
采用响应面法（RSM）,研究了单板厚度和涂胶量对桉木单板层积材（L、几）力学性能的影响。结果表明：单板厚度和涂胶量对桉木LVL的垂直加载和平行加载条件下的静曲强度（MOR┷、MOR／／）和弹性模量（MOE┷、／dOE／／）有显著影响。实验值与预测值的决定系数为0．72,0．79,0．59,0．69。本研究所获最佳工艺条件为：单板厚度2．0啪,涂胶量233g·m＾-2在此工艺条件下压制的桉木单板层积材垂直加载条件下的静曲强度（MORJ和弹性模量（MOE上）分别为85MPa与15118MPa,平行加载条件下的静曲强度（MOR／／）和弹性模量（MOE／／）分别为87MPa与15288MPa,回归模型的预测值与实验值的相对误差最大为9％,最小为3％。实验产品的MOR和MOE分别达到结构用单板层积材国家标准的优等品和140E级别。 相似文献
2.
3.
玻璃纤维增强结构用单板层积材热压工艺研究 总被引：1，自引：0，他引：1
通过玻璃纤维增强速生杨木制备杨木单板层积材(LVL),可提高杨木的强度等级,使其达到结构集成材层板的使用要求。采用正交实验方法,研究温度、时间、压力、偶联剂浓度、涂胶量对杨木单板层积材弹性模量、静曲强度、剪切强度的影响,其中主要研究热压工艺对力学强度的影响,得出的最优工艺参数为:热压温度130℃、时间100s/mm、压力1.2MPa。 相似文献
4.
以杨木单板和竹帘为原料,采用低分子量水溶性酚醛树脂浸渍处理,通过干燥、组坯、热压等工艺制备竹木复合强化单板层积材。探讨了组坯方式、压缩率、热压温度、热压时间4个因素对竹木复合强化单板层积材弹性模量(MOE)和静曲强度(MOR)的影响。结果表明:表层为一层竹帘的竹木复合强化单板层积材的MOE和MOR较大,分别是13．43GPa、148．13MPa,与表层为杨木单板次表层为竹帘组坯方式相比分别增加了33．63％、56．16％。确定了竹木复合强化单板层积材较合理的制造工艺参数。 相似文献
5.
酚醛树脂浸渍处理对杉木单板层积材性能的影响 总被引：2，自引：0，他引：2
采用自制低分子量酚醛树脂浸渍处理杉木单板,探讨了浸渍处理工艺对其增重率和单板层积材性能的影响,研究结果表明在常温常压和加压条件下,增重率均随浸渍时间的延长而增加,随着增重率的增大,板材密度逐渐增大,吸水厚度膨胀率(TS)逐渐降低,静曲强度(MOR)和弹性模量(MOE)先增大后减小.干增重率52.5％时,MOR和MOE达到最大,分别为51.19MPa和10 886MPa,MOR达到了GB/T 20241-2006《单板层积材》120E优级,MOE达到了100E级.鉴于产品质量和生产成本,建议采用浸胶法生产杉木单板层积材时,干增重率控制在50％左右,湿增重率控制在160％左右. 相似文献
6.
选用双组分水性环氧树脂为胶黏剂,速生桉木单板为基材,热压制备结构用桉木单板层积材。采用单因素试验法研究了施胶量、热压温度、热压时间、热压压力对水性环氧树脂单板层积材弹性模量、静曲强度、水平剪切强度、含水率和浸渍剥离率等物理力学性能的影响。结果表明:水性环氧树脂以水为分散剂,在木质单板表面延展性良好。当施胶量为230 g/m^(2),热压温度为120℃,热压时间为1.0 min/mm,热压压力为2 MPa时,单板层积材各项性能较优,符合GB/T20241—2006《单板层积材》要求。提出的以水性环氧树脂为胶黏剂的层积材制备工艺适合工业化生产,产品力学性能优良且无醛/低醛释放,绿色环保,具有积极的推广意义。 相似文献
7.
8.
介绍了单板层积材、密实型单板层积材在国内外的研究和利用概况.探讨了采用低分子量酚醛树脂浸渍处理杨木单板的方法制备杨木单板层积材的生产技术.结果表明:施胶量相当时,浸渍方式与涂胶方式生产的单板层积材相比,密度相当,吸水厚度膨胀(24hTS)降低了24%,胶合强度提高了:16%,弹性模量(MOE)和静曲强度(MOR)分别提高了20.17%和44.76%.采用浸渍树脂方式生产的密实型强化杨木单板层积材随着吸药量的增多,密度增大;24hTS减小;胶合强度随着吸药量的增加先增大而后趋于平稳;MOE和MOR先增大后减小.当吸药量为168%时,MOE、MOR达到最大,分别为15.34GPa和135.31 MPa.密实型强化单板层积材能够满足建筑和木结构等结构材要求,具有良好的发展空间. 相似文献
9.
10.
11.
Cheng Xing S. Y. Zhang James Deng Bernard Riedl Alain Cloutier 《Wood Science and Technology》2006,40(8):637-646
The properties of medium-density fiberboard (MDF) panels as affected by wood fiber characteristics were investigated. Wood chips from three softwood and one hardwood species were refined under the same refining conditions to make four different types of fibers. The resulting fibers were characterized by fiber size distribution, bulk density, pH value, and buffering capacity. Using the same resin system and hot-pressing parameters, MDF panels were produced and evaluated for internal bonding (IB), modulus of rupture (MOR), modulus of elasticity (MOE), thickness swelling, and linear expansion. The pH values and alkaline buffering capacities of raw materials were reduced considerably after refining. IB was strongly related to the pH value of fibers. The mechanical properties increased with alkaline buffering capacity. IB, MOR, and MOE increased with the bulk density of fibers. Increased proportions of coarse fibers had negative effects on the panel mechanical properties. 相似文献
12.
LIN Lanying FU Feng Research Institute of Wood Industry Chinese Academy of Forestry Beijing China 《中国林业科技(英文版)》2007,6(3):17-25
Resonance flexural vibration（Fast Fourier Transform, FFT）, ultrasonic wave（Pundit） and stress wave（Metriguard） techniques were examined as means of evaluating the static modulus of elasticity （MOE） and predicting the modulus of rupture （MOR） of finger-jointed lumber specimens made with four kinds of Eucalyptus （Eucalyptus. citriodora, E. exserta, E. grandis x E. urophylla and E. grandis）. Dynamic MOE was calculated from frequency and time obtained from forced vibrations and sounds induced in the four species of finger-jointed specimens. It was found that correlation coefficients between density and static MOE and dynamic MOE were statistically significant at the 0.01 level. And it was also found that the three nondestructive techniques can provide rapid and accurate means to determine the MOE, and the dynamic MOE was more accurate to predict static MOE than density. But the correlation coefficient between dynamic MOE, static MOE and MOR were lower than results reported by other researchers for solid wood, and were not statistically significant. It can be concluded that the three nondestructive techniques are useful for evaluating the MOE, but not suitable for predicting the MOR of finger-jointed. 相似文献
13.
14.
Song-Yung Wang Cheng-Jung Lin Chih-Ming Chiu Jin-Hau Chen Te-Hsin Yung 《Journal of Wood Science》2005,51(1):1-6
The effects of different thinning and pruning methods on the bending strength and dynamic modulus of elasticity (DMOE) of young Taiwania (Taiwania cryptomerioides Hay) were investigated. The average DMOE, modulus of elasticity (MOE), and modulus of rupture (MOR) in the thinning treatments showed the following trend: no thinning > medium thinning > heavy thinning. This indicates that thinning reduces average bending properties. The average DMOE, MOE, and MOR in the pruning treatments showed the following trend: medium pruning > no pruning > heavy pruning. According to this tendency, better average qualities of lumber and specimens were from wood subjected to no-thinning and medium-pruning treatments according to an ultrasonic wave technique and static bending tests. However, most results showed no statistically significant differences among thinning, pruning, and thinning and pruning treatments. The average values of DMOE, MOE, and MOR of visually graded construction-grade lumber were significantly greater than those of below-grade lumber. Moreover, there were very significant positive relationships between density, ultrasonic velocity, DMOE, MOE, and MOR, although the determination coefficients were small. 相似文献
15.
《湖北林业科技》2012,(6)
对江汉平原水杉、池杉、落羽杉人工林物理力学性能进行了研究,结果表明:落羽杉的密度和硬度最大;落羽杉、水杉、池杉的抗弯强度差异不大;水杉的弹性模量最大,约为落羽杉的2.3倍,落羽杉的弹性模量与池杉的比较接近。南北方向对水杉、池杉、落羽杉的密度、顺纹抗压强度在5%水平上差异均不显著,对池杉、水杉抗弯强度在5%水平上差异不显著,对落羽杉抗弯强度在1%水平上差异显著,对落羽杉、池杉的弹性模量在1%水平上差异显著,对水杉的弹性模量在5%水平上差异不显著。三杉南北面近树皮处木材的密度、抗弯强度、弹性模量、顺纹抗压强度均大于髓心处。对水杉、池杉、落羽杉物理力学性能比较研究,旨在为其培育及合理利用提供依据。 相似文献
16.
不同热压方法对无胶竹碎料板力学性能影响 总被引：1，自引：0，他引：1
分别采用普通热压和喷蒸热压两种热压方法制备了无胶竹碎料板,对它们的物理力学性能进行了对比研究与分析.结果表明,与普通热压法相比,喷蒸热压法制备的无胶竹碎料板的静曲强度、弹性模量与内结合强度明显提高,吸水厚度膨胀率显著减小,这可能是因为两种热压法热压过程中竹碎料发生的化学变化不同所致. 相似文献
17.
Mohammad Derikvand Nathan Kotlarewski Michael Lee Hui Jiao Gregory Nolan 《Wood material science & engineering》2020,15(3):172-181
ABSTRACTThe main goal of this study was to investigate the visual characteristics, recovery rate, and flexural properties of sawn boards from a fibre-managed plantation Eucalyptus globulus resource as a potential raw material for structural building applications. The impacts of the visual characteristics, strength-reducing features, and variation in basic density and moisture content on the bending modulus of elasticity (MOE) and modulus of rupture (MOR) of the boards were investigated. The reliabilities of different non-destructive methods in predicting MOE and MOR of the boards were evaluated, including log acoustic wave velocity measurement and numerical modellings. The MOE and MOR of the boards were significantly affected by the slope of grain, percentage of clear wood, and total number of knots in the loading zone of the boards. The normal variation in basic density significantly influenced the MOE of the boards while its effect on the MOR was insignificant. The numerical models developed using the artificial neural network (ANN) showed better accuracies in predicting the MOE and MOR of the boards than traditional multi-regression modelling and log acoustic wave velocity measurement. The ANN models developed in this study showed more than 78.5% and 79.9% success in predicting the adjusted MOE and MOR of the boards, respectively. 相似文献
18.
Arne Steffenrem Pekka Saranpää Sven-Olof Lundqvist Tore Skrøppa 《Annals of Forest Science》2007,64(8):799-806
Genetic- and environmental variation and correlation patterns were characterized for modulus of elasticity (MOE), modulus of rupture (MOR) and related wood traits: latewood proportion, wood density, spiral grain, microfibril angle and lignin content in five full-sib families of Norway spruce. The families were evaluated on the basis of clearwood specimens from the juvenile -mature wood transition zone of 93 sampled trees at age 30 year from seed. Family-means varied significantly (p < 0.05) for all wood traits studied except lignin content. MOE varied between 7.9–14.1 GPa among trees and 9.4–11.0 GPa among families. MOR varied between 47–87 MPa among trees and 61–71 MPa among families. Families remained significantly different in an analysis of specific MOE (MOE/density) and MOR (MOR/density). Hence, solely relying on wood density as a wood quality trait in tree breeding would not fully yield the potential genetic gain for MOE and MOR. Correlations between wood structural traits and specific MOE and MOR are presented and discussed. 相似文献
19.
Hem-fir plywood were exposed to two brown rot fungi, Gloeophyllum trabeum and Postia placenta, and one white rot fungus, Trametes versicolor, to investigate the effect of fungal decay on mechanical properties of plywood. Results showed that modulus of rupture （MOR） and modulus of elasticity （MOE） of hem-fir plywood declined significantly by inoculating fungi, and weight loss of sample had a modest decrease. The fungi also made a greater effect on MOR than on MOE. Of three fungi, Postia placenta caused a most significant weight loss, and Gloeophyllum trabeum resulted in a largest flexural properties loss. Substantial declines in MOR and MOE of hem-fir plywood were also observed when the plywood samples were stored under wet conditions over 15 weeks, even in the absence of fungal attack. 相似文献