首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 93 毫秒
1.
氯化锌法活性炭生产中,从活化料(活性炭和氯化锌、氧化锌的混合物)中把活化剂——氯化锌浸提出来的过程称为氯化锌的回收.这一过程要求最大银度的回收高浓度的氯化锌.目前国内普遍采用单桶浸泡回收法,此法虽然能较充生的回收氯化锌,回收的氯化锌浓度也能达到要求.但是此法是间歇回收,操作繁琐,劳动强度大,氯化锌回收率低.全国各厂都探求一种连续回收设备代替间歇回收,以提高劳动生产力,降低劳动强度、提高氯化锌的回收率.  相似文献   

2.
氯化锌法活性炭生产,无论是土法平板炉、双层炉还是回转炉等传统的生产方法都不同程度地存在着废气污柒、操作环境恶劣、锌耗、成本高等问题.为改变氯化锌法活性炭生产现状,提高产品质量,降低生产成本以及改善操作环境,减少废气污染,本试验采用了干燥炭化新工艺,针对干燥炭化温度,锌屑含水率对物料的粘结状态以及废气情况等有关因素进行了观察,并对活化产品进行了分析检测.  相似文献   

3.
《技术与市场》2007,(3):F0002-F0002
国家重点高新技术浙江丰利粉碎设备有限公司研发的国家专利产品、省级新产品,列入2005年浙江省重点技术创新项目计划。该设备采用先进的物理法回收工艺;废旧线路板→强力破碎→磁选→中碎→精细粉碎→超微分级→高压静电分离→成品;所研制的强力破碎机、中碎机、精细粉碎机、超微分级机、高压静电分离等设备创新性强,其资源化的处理工艺路线先进合理。该设备能对各类废旧印刷线路板及加工废料、废旧电器等进行机械粉碎回收处理,其金属回收率高,回收金属的纯度高达97%。[第一段]  相似文献   

4.
目前,我国活性炭的生产,大多数采用氯化锌法,水蒸汽和闷烧法.气体活化法虽然没有公害,是发展方向,但缺少理想的炉型,未能得到迅速的发展.用氯化锌法生产活性炭,虽然氯化锌耗量较大,有一定的公害,但由于本法生产简单,产品脱色性能优良,质量比较稳定,得率高,所以氯化锌法活性炭的产量仍占全国总产量的53.13%.如何降低锌耗,消除公害就成为当前国内氯化锌法活性炭生产中迫切需要解决的问题.为此,我们于1977年  相似文献   

5.
用氯化锌法生产活性炭,氯化锌溶液的浓度,决定锌木屑中氯化锌的含量,从而影响活性炭孔径分布和孔隙度.在生产中,氯化锌溶液浓度常用波美计测定,但其波美度受温度影响较大,要在某一温度下配制出达到工艺要求的氯化锌溶液的波美值,以往凭经验配制很不准确.本文根据多次实验数据,应用回归分析法找出温度与波美度的数学关系,以解决上述问题.  相似文献   

6.
氯化锌法木质活性炭生产过程中,有两个主要污染散发源。1,大气污染源;2,废水污染源。在实验室条件下,从废气中损失的氯化锌约为氯化锌损失总量的1/3,废水中为2/3。研究表明,废水主要污染物质由残存的盐酸、氯化锌、氯化亚铁、二氯化铁、氯化镁、氯化钙以及Al~(3 )、K~ 、Mn~(2 )等所组成。而有机污染物质含量甚微。这样的废水,在适当条件下(pH值及石灰添加量等),采用中和絮凝的方法能得到有效的处理;添加适当高分子絮凝剂能改善絮凝体的沉降速率和过滤速率。研究结果也表明,污泥的回收利用以及处理过的废水循环回用至关重要。  相似文献   

7.
前言我国随着葡萄糖、食品、饮料、味精、药品等生产和环境保护、外贸事业的迅速发展,对活性炭的需求量不断增长,但因活性炭生产耗煤量大(生产1吨活性炭,焖烧法耗煤9吨,氯化锌法耗煤6吨),废气废水污染严重(氯化锌法生产1吨活性炭耗盐酸1吨  相似文献   

8.
有机废气回收装置,可广泛用于从印刷、烘烤房、涂布等工艺产生的废气中回收有机溶剂,该装置的技术经济指标如下:1)处理后废气中有机溶剂可达到排放标准;2)废气中有机溶剂的回收率大于90%;3)分子筛使用寿命在3年以上。  相似文献   

9.
微波氯化锌法马占相思木材剩余物制备活性炭   总被引:7,自引:1,他引:7  
以马占相思木材剩余物为原料,研究用微波辐射氯化锌法制备活性炭的可行性.探讨了微波辐射氯化锌法在微波功率900W、氯化锌溶液质量分数50%的条件下锌屑比、氯化锌溶液的pH值及微波辐射时间对产品得率、亚甲基蓝吸附值的影响.得到了微波辐射氯化锌法制备活性炭的最佳工艺:锌屑比2.5∶1、氯化锌溶液pH值为1、微波辐射时间6min,用此工艺制得的活性炭得率为47.5%,产品的亚甲基蓝吸附值达12.9mL/0.1g,是国家一级品标准(GB/T13803.2-1999)的1.43倍,该产品对Cr6 的吸附量为9.974mg(以1g活性炭计,Cr6 溶液pH值4.0,质量浓度50mg/L).  相似文献   

10.
氯化锌法颗粒活性炭试验研究   总被引:3,自引:0,他引:3  
以木屑为原料,采用氯化锌法在FS-Ⅲ型隧道活化炉中生产颗粒活性炭的工艺过程,并就生产中锌屑比、粘结剂、填充剂等的配比和活化温度、时间等对产品的吸附性能、强度及锌耗量的影响进行了试验探讨。  相似文献   

11.

In Scandinavia, moose (Alces alces L.) sometimes cause severe browsing damage to economically-important pine. Moose-vehicle accidents have spurred construction of fences along roads, and these may interfere with moose migration between summer and winter ranges, or the road alone may be a barrier. If this happens and moose build up along roads, landowners may suffer economically. Therefore, this study investigated whether roads, fences or other factors influence the use of young pine stands by moose. Eighty stands along roads in northern Sweden were evaluated in which individually-browsed branches were counted on 9972 pines. Moose browsing was not significantly related to birch (Betula pendula Roth, B. pubescens Ehrh.) density, nor did it differ between pines (Pinus contorta Douglas or P. sylvestris L.). However, increased pine density, site productivity and proximity to a highway were associated with increased browsing. Further large-scale studies are needed to understand moose habitat selection and the effects of roads.  相似文献   

12.

The root systems of 2-yr-old Picea glauca, Picea mariana and Pinus banksiana seedlings were submitted to various frost temperatures during an artificial frost to induce different levels of root damage. Frost-damaged and control seedlings were placed in a greenhouse under high and low soil moisture regimes. Seedling growth and physiology were evaluated periodically. Seedling survival was reduced when root damage reached levels of 60-80%. Root systems of all three species showed partial to total recovery by the end of the experiment. In general, root freezing damage caused reductions in seedling growth, with these reductions becoming less significant over time. Root damage had little to no effect on black spruce and jack pine seedling physiology, while white spruce CO 2 uptake decreased with increasing root damage. Shoot nitrogen content of all three species decreased slightly with increasing root damage.  相似文献   

13.
Contour hedgerows of multipurpose tree species in the sloping tea lands of Sri Lanka are expected to reduce soil erosion and also add significant amounts of plant nutrients to the soil via periodic prunings. The objective of this experiment was to characterize the biomass decomposition pattern and quantify the amount of nutrients added through prunings of six tree species (Calliandra calothyrsus, Senna spectabilis, Euphatorium innulifolium, Flemingia congesta, Gliricidia sepium and Tithonia diversifolia) currently being used in hedgerows associated with tea. Withered leaf and stem prunings (50 g) were enclosed in 2-mm litter bags, placed at 5-cm depth and retrieved after one, three, six, nine and 12 weeks. Loss of initial dry weight, N, P and K was measured. Single exponential decay function adequately described both dry weight and nutrient loss. Tree species differed significantly in their rate of breakdown with decomposition constants (k) varying from 0.0299 to 0.2006 week−1 for leaves and from 0.0225 to 0.0633 week−1 for stems. Gliricidia showed the highest k for leaves with the rest in the following descending order: Senna > TithoniaEuphatorium > Calliandra > Flemingia. A similar pattern was observed for loss of all nutrients with Calliandra and Flemingia always having lower k values than the rest. Although N immobilization was not observed, immobilization of P and K was observed during the first week of incubation in some species, particularly in stem prunings. Annual biomass of prunings differed significantly between tree species in the following descending order: Calliandra > Senna > Flemingia > Tithonia > Gliricidia > Euphatorium. Calliandra added the greatest amount of nutrients annually to the soil with Euphatorium adding the least. Calliandra prunings provided the annual total K requirement and 49% of the N requirement of mature tea. However, none of the species provided more than 5% of the P requirement. It is concluded that among the tree species tested, Calliandra and Flemingia are the most suitable for contour hedgerows in tea plantations of this agroclimatic region because of their higher soil nutrient enrichment capacity and slower decomposition rates which would minimize leaching losses. This revised version was published online in June 2006 with corrections to the Cover Date.  相似文献   

14.

The effects of seed weight and seed type on seedling growth of Pinus sylvestris (L.) were studied by seeding individually weighed orchard and stand seed in different mixtures under harsh (direct seeding in field) and optimal (seeding in nursery) conditions. In the nursery experiment an increase in the seed weight from 3 to 7 mg increased the seedling height by 10-27% and total weight by 27-113%, and decreased the height/diameter ratio by 5-6% after 2 yrs. With elimination of seed weight effects, orchard seedlings were 2% taller than stand seedlings in year 2. Without elimination of seed weight effects, orchard seedlings were 7-13% taller. In the field experiment an increase in the seed weight from 3 to 7 mg increased seedling height by 18-65%, stem volume by 81-274% and the number of top-buds by 23-34% in year 5. After elimination of seed weight effects, orchard seedlings were 7-13% taller than stand seedlings and without elimination of seed weight effects 20-21% taller after 5 yrs. Even after elimination of both seed weight and genetic effects orchard seedlings were 3-9% larger than stand seedlings in the field experiment. In conclusion, the influence of seed weight and seed type on growth traits and slenderness is highly significant and the influence seems to be greater in harsh conditions.  相似文献   

15.
Baobab leaves form an important part of the local diet in Sahel countries and elsewhere in Africa. Existing leaf nutritional data and agroforestry performance information are based solely on Adansonia digitata L., the baobab of continental Africa. The introduction potential of Adansonia species from the center of diversity in Madagascar and from Australia remains untapped. To assess this potential, the mineral contents and B1 and B2 vitamin levels of dried baobab leaves were determined for five-year old trees of A. digitata, A. gibbosa (A. Cunn.) Guymer ex D. Baum, A. rubrostipa Jum. & H. Perrier (syn. A. fony Baill.), A. perrieri Capuron and A. za Baill. grown in an introduction trial in Mali. Nutritional data were evaluated against survival and vigor to identify promising germplasm. Leaf vitamin and crude protein contents were highest in the Madagascar species, especially A. rubrostipa (B1 88 mg 100 g−1, B2 187 mg 100 g−1, protein 20.7% dry weight). However, the local species far outperformed the introductions in survival, tree height, basal diameter and resistance to termites. We suggest grafting as a way of harnessing the vigor of well-adapted local baobab varieties to the superior nutritional profiles of A. rubrostipa and others. Cross-species grafting tests in Adansonia were successful, thus creating new agroforestry possibilities with different scion/rootstock combinations.  相似文献   

16.
Abstract

Wood in general and wooden studs in particular are often distorted owing to uneven shrinkage during the drying process in the sawmill. Twist is often the most detrimental of all types of distortion, and it is caused by spiral grain in combination with variations in moisture content. For sawmills, the objective is to produce dried, straight boards, and one method of dealing with boards with excessive spiral grain is to sort them out and then dry them in a pretwisted position to obtain straight boards after drying. A model using the finite element (FE) method for the simulation of drying twist distortions was first calibrated against laboratory experiments in which boards were dried with and without restraints and pretwists. After the calibration, the FE results were compared with industrial test results for boards that were dried without restraints or with restraints with zero pretwist, i.e. straight restraints. The FE model used an elastic–ideally plastic material model to obtain permanent deformations. The calibration was to set the yield stresses so that there was a good match between FE results and results from the laboratory experiments. The comparison between the industrial test results and the FE results showed that the FE model is capable of realistic simulations of drying boards with and without restraints and presumably also pretwists.  相似文献   

17.

This study investigated the stand structure in pine, spruce and deciduous forests in the border district of Finland and Russia. A total of 46 mature forest stands was selected as pairs, the members of each pair being as similar as possible with respect to their forest site type, age, moisture and topography. The stands were then compared between the two countries by means of basal areas and number of stems. The proportions of dominating tree species were 2-12% lower, and correspondingly the proportions of secondary tree species higher, in Russian forests. The density of the forest stock was also higher in each forest type in Russia. The forests in the two countries differed most radically in terms of the abundance of dead trees. The amount was two to four times higher in Russian deciduous and spruce forests, and in pine forests the difference was 10-fold. The stand structures indicated that Russian coniferous stands, in particular, were more heterogeneous than intensively managed pine and spruce stands in Finland.  相似文献   

18.

The root collar diameter and the height:diameter ratio are of particular importance in container-grown seedlings where a high density in the containers may produce spindly seedlings. Temperature regimes and light quality are known to affect plant growth. The aim of this study was to identify responses in Picea abies (L.) Karst. seedlings grown with light providing different red:far-red ratios and under temperature regimes with alternating day (DT) and night temperature (NT) from negative (DT < NT) to positive (DT > NT) difference (DIF) between DT and NT. Experiments were conducted in controlled environment chambers and in a daylight phytotron. Only limited thermoperiodic responses appeared in P . abies seedlings with respect to seedling height and dry weight accumulation. The formation of terminal buds, however, was clearly delayed in seedlings grown at negative DIF. The results indicate a requirement for day extension light that is high in far-red, to prevent terminal bud formation under natural short-day conditions. An extended study should be conducted to clarify the minimum level of light intensity and the optimal light quality needed to prevent terminal bud formation under natural short-day conditions.  相似文献   

19.
本文分析了CAD在设计中引起的正面和负面影响,并进行了系统的阐述,从而使设计者在应用中能够保持客观的态度。  相似文献   

20.
Heterobasidion parviporum and Heterobasidion annosum are widely distributed root‐rot fungi that infect conifers throughout Europe. Infection of conifer stumps by spores of these pathogens can be controlled by treating fresh stumps with a competing non‐pathogenic fungus, Phlebiopsis gigantea. In this study, growth of three Latvian strains of P. gigantea and the biological control agent ‘Rotstop’ strain was evaluated in stem pieces of Norway spruce, Scots pine, lodgepole pine, Douglas‐fir, Weymouth pine, Siberian larch and Sitka spruce. The growth rates of one H. parviporum and one H. annosum isolate were also measured in the same stem pieces. The growth rate of P. gigantea varied greatly in wood of different conifer species. It was higher in the three pine species, lower in Norway spruce and lowest in Sitka spruce and Siberian larch, and in Douglas‐fir, this fungus did not grow. The largest area of wood occupied by P. gigantea was in lodgepole pine. Growth of Latvian isolates of P. gigantea in the wood of Pinus and Picea species was comparable to that of the Rotstop isolate. Consequently, stump treatment with local P. gigantea isolates should be recommended. However, our results suggest that Douglas‐fir stump treatment against Heterobasidion by P. gigantea may be ineffective and other stump treatment methods should be considered.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号