共查询到20条相似文献，搜索用时 15 毫秒
1.
Surface functional properties of native, acid-treated, and reduced soy glycinin. 1. Foaming properties 总被引：4，自引：0，他引：4
Foaming properties of native and chemically modified glycinin were evaluated. Effects of ionic strength and glycinin composition and concentration on foam formation and stabilization were studied. Glycinin was modified by means of combined treatments: cold or hot acidic treatments, with or without later disulfide bridges reduction. Modified proteins obtained from glycinin present different degrees of dissociation, deamidation, and as consequence, varied surface hydrophobicity and molecular size. Parameters of forming and stabilizing of foam were correlated with both deamidation and dissociation degrees of modified and native glycinin samples. A positive relationship was observed between surface behavior and foaming properties of different protein species. Results show that dissociation, deamidation, and reduction have produced structural changes on glycinin (increased surface hydrophobicity, increased net charge, decreased molecular size) which enhance the adsorption and anchorage of proteins at the air-water interface and, consequently, improve the foam forming and stabilizing capacities. 相似文献
2.
Cabra V Arreguin R Vazquez-Duhalt R Farres A 《Journal of agricultural and food chemistry》2007,55(2):439-445
Different deamidation conditions for the Z19 alpha-zein were studied in order to find the best conditions for the development of the emulsifying properties. Alkaline deamidation was chosen, and the effects on the peptide bond cleavage, secondary structure, emulsifying properties, and surface hydrophobicity were studied. The Z19 alpha-zein was deamidated by using 0.5 N NaOH containing 70% ethanol at 70 degrees C for 12 h. A deamidation degree (DD) of 60.6 +/- 0.5%, and a degree of hydrolysis (DH) of 5 +/- 0.5% were achieved. Analysis by far-UV circular dichroism showed that the denaturation was mainly promoted by the high temperature used during the incubation. The adequate balance between the DD and the DH results in an effective emulsifying property improvement for the Z19 alpha-zein. Thus, after the deamidation treatment, the surface hydrophobicity decreased from 9.5 x 104 +/- 6.8 x 103 to 46 x 104 +/- 2.1 x 103, and the emulsion stability increased from 18 +/- 0.7% to 80 +/- 4.7% since the oil globules stabilized by the modified protein were smaller (57.7 +/- 5.73 nm) and more resistant to coalescence than those present in the native protein emulsions (1488 +/- 3.92 nm). 相似文献
3.
Garcia RN Adachi M Tecson-Mendoza EM Bernardo AE Utsumi S 《Journal of agricultural and food chemistry》2006,54(16):6005-6010
We have previously cloned and characterized the cDNAs of three isoforms of the 8S globulin of mungbean, expressed the major 8Salpha isoform in Escherichia coli, and purified and successfully crystallized it (Bernardo, A. E. N.; Garcia, R. N.; Adachi, M.; Angeles, J. G. C.; Kaga, A; Ishimoto, M.; Utsumi, S.; Tecson-Mendoza, E. M. J. Agric. Food Chem. 2004, 52, 2552-2560). Herein, we report the physicochemical and emulsifying properties of the native 8S and recombinant 8Salpha globulin or vicilin. The circular dichroism spectra analysis of the native 8S and recombinant 8Salpha globulins revealed that the recombinant 8Salpha formed a secondary structure close to that of the native 8S. Further, gel filtration analysis showed that 8Salpha was able to assemble into trimers. The native 8S and recombinant 8Salpha globulins were soluble at pH 3.4 and at pH 7.4-9.0 at low ionic strength, mu = 0.08. Interestingly, the native 8S was more soluble at pH 7.0 and pH 7.4 than the recombinant 8Salpha at mu = 0.08. Both forms were very soluble at pH 3.4-9.0 at high ionic strength, mu = 0.50. The native form exhibited a higher T(m) (69.2, 79.5, and 83.8 degrees C) than the recombinant form (65.6, 71.6, 77.5 degrees C) at mu = 0.1, 0.2, and 0.5, respectively. The recombinant form was found to have greater surface hydrophobicity than the native form. There was little difference in the emulsifying ability between the native 8S and 8Salpha at pH 3.4 and pH 7.6. The results indicate that the presence of N-linked glycans is not essential in the assembly and stable conformation of the mungbean vicilin. However, the N-linked glycans might have contributed to the higher solubility at low ionic strength, greater thermal stability, and decreased surface hydrophobicity of the native vicilin as compared to the recombinant 8Salpha. On the other hand, the N-linked glycans showed little effect on the emulsifying ability of the protein. 相似文献
4.
Mohamed Salleh MR Maruyama N Adachi M Hontani N Saka S Kato N Ohkawa Y Utsumi S 《Journal of agricultural and food chemistry》2002,50(25):7380-7385
Rapeseeds contain cruciferin (11S globulin), napin (2S albumin), and oleosin (oil body protein) as major seed proteins. The effects of oil expression and drying conditions on the extraction of these proteins from rapeseed meal were examined. The conditions strongly affected the extraction of oleosin and only weakly affected the extraction of cruciferin and napin. The protein chemical and physicochemical properties of cruciferin, the major protein present, were compared with those of glycinin (soybean 11S globulin) under various conditions. In general, cruciferin exhibited higher surface hydrophobicity, lower thermal stability, and lower and higher solubility at mu= 0.5 and mu = 0.08, respectively, than did glycinin. At the pHs (6.0, 7.6, and 9.0) and ionic strengths (mu= 0.08 and 0.5) examined, the emulsifying ability of cruciferin was worse than that of glycinin, except at mu= 0.08 and pH 7.6. The emulsifying abilities of cruciferin and glycinin did not correlate with thermal stability and surface hydrophobicity. Higher protein concentration, higher heating temperature, higher pH, and lower ionic strength were observed to produce harder gels from cruciferin. Gel hardness partly correlated with the structural stability of cruciferin. 相似文献
5.
The seed of cowpea (Vigna unguiculata L.) is rich in protein and the amino acid profiles of the meal are suitable for human dietary products, but little is known about the structure and chemical properties of the protein extracted from this legume. This study determined the functional properties of two selected cowpea cultivars and their solubility, emulsifying capacity, surface hydrophobicity, and thermal stability. Seeds of red and black cowpea were surface sterilized and the 7s globulin was isolated and purified using column chromatography with Sephacryl S‐300 (Hi‐Prep 26/60) gel column. Also, SDS‐PAGE and protein structure were analyzed using biochemical procedures. At high ionic strength (μ = 0.5), cowpea 7s globulin fraction exhibited better solubility for a wide range of pH levels, higher emulsifying capacities, and greater thermal stability than those obtained at low ionic strength (μ = 0.08). The lowest solubility was observed at pH 5.3–6.4 at the low ionic strength. Emulsifying capacities at high protein concentration were greater when compared with low protein concentration. Tm values of black cowpea globulin fraction were higher than those of red cowpea globulin fraction, whereas the surface hydrophobicity of the globulin fraction in red cowpea was larger than that in black cowpea. 相似文献
6.
Kimura A Fukuda T Zhang M Motoyama S Maruyama N Utsumi S 《Journal of agricultural and food chemistry》2008,56(21):10273-10279
Legume seeds contain 7S and/or 11S globulins as major storage proteins. The amino acid sequences of them from many legumes are similar to each other in the species but different from each other, meaning that some of these proteins from some crops exhibit excellent functional properties. To demonstrate this, we compared protein chemical and functional properties (thermal stability, surface hydrophobicity, solubility as a function of pH, and emulsifying properties) of these proteins from pea, fava bean, cowpea, and French bean with those of soybean as a control at the same conditions. The comparison clearly indicated that the 7S globulin of French bean exhibited excellent solubility (100%) at pH 4.2-7.0 even at a low ionic strength condition (mu = 0.08) and excellent emulsion stability (a little phase separation after 3 days) at pH 7.6 and mu = 0.08, although the emulsions from most of the other proteins separated in 1 h. These results indicate that our assumption is correct. 相似文献
7.
Ilankovan Paraman N. S. Hettiarachchy Christian Schaefer Markus I. Beck 《Cereal Chemistry》2007,84(4):343-349
Rice endosperm protein was modified to enhance solubility and emulsifying properties by controlled enzymatic hydrolysis. The optimum degree of hydrolysis (DH) was determined for acid, neutral, and alkaline type proteases. Solubility and emulsifying properties of the hydrolysates were compared and correlated with DH and surface hydrophobicity. DH was positively associated with solubility of resulting protein hydrolysate regardless of the hydrolyzing enzyme, but enzyme specificity and DH interactively determined the emulsifying properties of the protein hydrolysate. The optimum DH was 6–10% for good emulsifying properties of rice protein, depending on enzyme specificity. High hydrophobic and sulfhydryl disulfide (SH-SS) interactions contributed to protein insolubility even at high DH. The exposure of buried hydrophobic regions of protein that accompanied high-temperature enzyme inactivation promoted aggregation and cross-linking of partially hydrolyzed proteins, thus decreasing the solubility and emulsifying properties of the resulting hydrolysate. Due to the highly insoluble nature of rice protein, surface hydrophobicity was not a reliable indicator for predicting protein solubility and emulsifying properties. Solubility and molecular flexibility are the essential factors in achieving good emulsifying properties of rice endosperm protein isolates. 相似文献
8.
The functional properties of cod myosin and washed cod mince (myofibrillar protein fraction) treated at high (11) and low (2.5) pH were investigated after pH readjustment to 7.5. The solubility of refolded myosin was essentially the same as the native myosin. The pH-treated myofibrillar proteins had increased solubility over the whole ionic strength range studied. Acid and alkali treatment gave myosin and myofibrillar proteins improved emulsification properties, which were correlated with an increase in surface hydrophobicity and surface/interfacial activity. Enhanced gel strength was observed with acid- and alkali-treated myosin compared to native myosin, while the same treatment did not significantly improve the gel strength of acid- and alkali-treated myofibrillar proteins. The acid- and alkali-treated protein samples unfolded and gelled at a lower temperature than did the native proteins, suggesting a less conformationally stable structure of the refolded proteins. Functional studies show that acid and alkali treatment, which leads to partial unfolding of myosin may improve functional properties of cod myosin and myofibrillar proteins, with the greatest improvement being from the alkali treatment. The results also show that improvements in functionality were directly linked to the extent of partial unfolding of myosin on acid and alkali unfolding and refolding. 相似文献
9.
为提升大豆分离蛋白（soy protein isolate,SPI）的功能性质,该文引入大豆可溶性多糖（soybean soluble polysaccharides,SSPS）,构建大豆分离蛋白-大豆可溶性多糖体系（SPI-SSPS）,研究动态高压微射流（dynamic high-pressure microfluidization,DHPM）处理对SPI-SSPS功能特性的影响。分别采用0,60,100,140和180 MPa的 DHPM压力处理SPI-SSPS,探究不同压力对SPI-SSPS起泡特性、乳化特性、溶解性、粒度分布和表面疏水性的影响。结果表明,DHPM处理能提高SPI的溶解性和起泡特性,且SSPS的存在能显著提高DHPM对SPI功能性质的改善效果（P<0.05）。100和60 MPa的DHPM处理能使SPI-SSPS呈现较高的起泡能力和起泡稳定性,分别为未处理样品的1.2和2.4倍。140 MPa的DHPM处理使SPI-SSPS溶解性较强,为未处理样品的1.8倍。然而,DHPM处理会显著降低SPI-SSPS的乳化特性、粒径和表面疏水性（P<0.05）。随着处理压力的增加,SPI-SSPS的粒度和表面疏水性逐渐降低,在180MPa的DHPM处理下SPI-SSPS具有较小的粒径和较低的荧光强度。综上所述,DHPM结合SSPS改性技术可用于改善SPI的功能性质（如溶解性、起泡性）,促进SPI在食品工业的应用。该文的研究结果可为SPI的功能性质改性提供参考。 相似文献
10.
Suppavorasatit I De Mejia EG Cadwallader KR 《Journal of agricultural and food chemistry》2011,59(21):11621-11628
The effects of enzymatic deamidation by protein-glutaminase (PG) on the functional properties of soy protein isolate (SPI) were studied. Conditions for the deamidation were evaluated by means of response surface methodology (RSM). Optimal conditions based on achieving a high degree of deamidation (DD) with a concurrently low degree of hydrolysis (DH) were 44 °C, enzyme:substrate ratio (E/S) of 40 U/g protein and pH 7.0. Under optimal conditions, both DD and DH increased over time. SDS-PAGE results indicated that lower molecular mass subunits were produced with increasing DD. Far-UV circular dichroism spectra revealed that the α-helix structure decreased with higher DD, while the β-sheet structure increased until 15 min of deamidation (32.9% DD), but then decreased at higher DD. The solubility of deamidated SPI was enhanced under both acidic and neutral conditions. SPI with higher DD showed better emulsifying properties and greater foaming capacity than SPI, while foaming stability was decreased. It is possible to modify and potentially improve the functional properties of SPI by enzymatic deamidation using PG. 相似文献
11.
Surface hydrophobicity (SH) of milk proteins treated physicochemically (by heating and Maillard reaction) or modified enzymatically (by transglutaminase, lactoperoxidase, laccase, and glucose oxidase) was assessed in relation to their techno-functional properties. Heat-treatment increased SH of whey protein isolate and decreased SH of sodium caseinate and bovine serum albumin. Maillard reaction of milk proteins caused time-depended decreases of SH. Only for total milk protein reacting with glucose and lactose elevated SH-values were detected. Protein modification with transglutaminase, laccase, and lactoperoxidase strongly increased the SH of whey protein isolate and total milk protein. Incubation with glucose oxidase elevated SH values of sodium caseinate, whey protein isolate, and total milk protein. When correlating SH with techno-functional properties, a positive correlation was observed between SH and foam formation, and a negative correlation was observed between SH and foam stability as well as emulsion stability. No clear correlation was detected between SH and emulsifying activity, surface tension, viscosity, and heat stability of enzymatically and physicochemically treated milk proteins. 相似文献
12.
Soy protein isolate (SPI) was modified by ultrasound pretreatment (200 W, 400 W, 600 W) and controlled papain hydrolysis, and the emulsifying properties of SPIH (SPI hydrolysates) and USPIH (ultrasound pretreated SPIH) were investigated. Analysis of mean droplet sizes and creaming indices of emulsions formed by SPIH and USPIH showed that some USPIH had markedly improved emulsifying capability and emulsion stabilization against creaming during quiescent storage. Compared with control SPI and SPIH-0.58% degree of hydrolysis (DH), USPIH-400W-1.25% (USPIH pretreated under 400W sonication and hydrolyzed to 1.25% DH) was capable of forming a stable fine emulsion (d43=1.79 μm) at a lower concentration (3.0% w/v). A variety of physicochemical and interfacial properties of USPIH-400W products have been investigated in relation to DH and emulsifying properties. SDS-PAGE showed that ultrasound pretreatment could significantly improve the accessibility of some subunits (α-7S and A-11S) in soy proteins to papain hydrolysis, resulting in changes in DH, protein solubility (PS), surface hydrophobicity (H0), and secondary structure for USPIH-400W. Compared with control SPI and SPIH-0.58%, USPIH-400W-1.25% had a higher protein adsorption fraction (Fads) and a lower saturation surface load (Γsat), which is mainly due to its higher PS and random coil content, and may explain its markedly improved emulsifying capability. This study demonstrated that combined ultrasound pretreatment and controlled enzymatic hydrolysis could be an effective method for the functionality modification of globular proteins. 相似文献
13.
Corredig M Verespej E Dalgleish DG 《Journal of agricultural and food chemistry》2004,52(14):4465-4471
The physical aggregation of commercial whey protein isolate (WPI) and purified beta-lactoglobulin was studied by ultrasound spectroscopy. Protein samples were dialyzed to achieve constant ionic strength backgrounds of 0.01 and 0.1 NaCl, and gelation was induced in situ at constant temperatures (from 50 to 75 degrees C) or with a temperature ramp from 20 to 85 degrees C. Changes in the ultrasonic properties were shown in the early stages of heating, at temperatures below those reported for protein denaturation. During heating, the relative ultrasound velocity (defined as the difference between sample velocity and reference velocity) decreased continuously with temperature, indicating a rearrangement of the hydration layer of the protein and an increase in compressibility of the protein shell. At temperatures <50 degrees C the ultrasonic attenuation decreased, and <65 degrees C both velocity and attenuation differentials showed increasing values. A sharp decrease in the relative velocity and an increase in the attenuation at 70 degrees C were indications of "classical" protein denaturation and the formation of a gel network. Values of attenuation were significantly different between samples prepared with 0.01 and 0.1 M NaCl, although no difference was shown in the overall ultrasonic behavior. WPI and beta-lactoglobulin showed similar ultrasonic properties during heating, but some differences were noted in the values of attenuation of WPI solutions, which may relate to a less homogeneous distribution of aggregates caused by the presence of alpha-lactalbumin and other minor proteins in WPI. 相似文献
14.
Emulsifying properties of acidic subunits of soy 11S globulin 总被引：3，自引：0，他引：3
The emulsifying properties of the acidic subunits (AS11S) isolated from soy glycinin (11S) have been studied. The isolated AS11S existed in solution mainly as a dimer species. Circular dichroic analysis indicated only a slight increase in aperiodic structure and no significant difference in beta-sheet structure when compared with those of soy 11S. At similar experimental conditions, the emulsifying properties of AS11S were superior to those of soy 11S and heat-denatured 11S. Emulsions prepared with 1% AS11S remained very stable without any visible oil separation for more than a month under gentle agitating conditions, whereas those prepared with 1% 11S collapsed and separated into phases within 2-3 days. The AS11S-stabilized emulsions were very stable below 0.15 M ionic strength. Studies on the rate of adsorption and surface tension reduction at the air-water interface showed that AS11S was significantly more surface active than soy 11S. It is proposed that, because the mass fraction of acidic subunits in soy 11S is approximately 60% and it is relatively easy to separate the acidic subunits from soy 11S, it may be industrially feasible to develop an economical process to isolate functional acidic subunits for use in emulsion-based food products. 相似文献
15.
Ruíz-Henestrosa VP Sánchez CC Rodríguez Patino JM 《Journal of agricultural and food chemistry》2008,56(7):2512-2521
In this contribution, we have analyzed the effect of sucrose on dynamic interfacial (dynamic surface pressure and surface dilatational properties) and foaming (foam capacity and foam stability) characteristics of soy globulins (7S and 11S). The protein (at 1 x 10(-3), 1 x 10(-2), 0.1, and 1 wt %) and sucrose (at 0, 0.25, 0.5, and 1.0 M) concentrations in aqueous solution and the pH (at 5 and 7), and ionic strength (at 0.05 and 0.5 M) were analyzed as variables. The temperature was maintained constant at 20 degrees C. We have observed the following. (i) The dynamics of adsorption (presence of a lag period, diffusion, and penetration at the air-water interface) of soy globulins depend on the peculiar molecular features of proteins (7S or 11S soy globulin) and the level of association/dissociation of these proteins by varying the pH and ionic strength, as well as the effect of sucrose in the aqueous phase on the unfolding of the protein. The rate of adsorption increases with the protein concentration in solution, at pH 7 compared to pH 5, at high ionic strength, and in the absence of sucrose. (ii) The surface dilatational properties reflect the fact that soy globulin adsorbed films exhibit viscoelastic behavior. The surface dilatational modulus increases at pH 7 compared to pH 5, but decreases with the addition of sucrose into the aqueous phase. (iii) The rate of adsorption and surface dilatational properties (surface dilatational modulus and phase angle) during adsorption at the air-water interface play an important role in the formation of foams generated from aqueous solutions of soy globulins. (iv) The increased interfacial adsorption (at high surface pressures) and the combined effects of interfacial adsorption and interfacial interactions between adsorbed soy globulin molecules (at high surface dilatational modulus) can explain the higher stability of the foam, with few exceptions. 相似文献
16.
17.
提高大豆蛋白冻融后乳化性改性工艺优化 总被引：4，自引：1，他引：3
为了制备出经冷冻-融化后仍能保持较高乳化性的大豆蛋白,试验以葡聚糖为糖基化供体,采用湿法糖基化技术改性大豆蛋白。根据单因素试验的结果,建立了Box-Behnken模型对加工工艺进行优化,所得的模型拟合度高,切实可行,可用于实际分析和预测。利用响应面分析法探讨了蛋白浓度、蛋白与糖质量比、反应时间3因素对改性产物冻融前后乳化活性和乳化稳定性的影响,优化的工艺条件为:大豆分离蛋白(soybean protein isolate,SPI)质量浓度40 mg/mL,SPI与葡聚糖的质量比为1∶3,反应时间4 h。在此条件下得到的改性产物冻融稳定性显著(P0.05)高于未改性蛋白,冻融前后的乳化活性(emulsifying activity index,EAI)分别是空白对照样的1.687和1.780倍,乳化稳定性(emulsion stability index,ESI)分别是空白对照样的1.367和1.274倍。傅里叶红外光谱证明葡聚糖通过共价键接到大豆蛋白分子中,研究结果为制备冷冻食品加工专用大豆蛋白的产业化生产提供参考。 相似文献
18.
Brewers' spent grain (BSG) is the insoluble residue of barley malt resulting from the manufacture of wort. Although it is the main byproduct of the brewing industry, it has received little attention as a marketable commodity and is mainly used as animal feed. Our work focuses on one of the main constituents of BSG, i.e., the proteins. The lack of solubility of BSG proteins is one of the limitations for their more extensive use in food processing. We therefore aimed to generate BSG protein hydrolysates with improved technofunctional properties. BSG protein concentrate (BPC) was prepared by alkaline extraction of BSG and subsequent acid precipitation. BPC was enzymatically hydrolyzed in a pH-stat setup by several commercially available proteases (Alcalase, Flavourzyme, and Pepsin) for different times and/or with different enzyme concentrations in order to obtain hydrolysates with different degrees of hydrolysis (DH). Physicochemical properties, such as molecular weight (MW) distribution and hydrophobicity, as well as technofunctional properties, such as solubility, color, and emulsifying and foaming properties, were determined. Enzymatic hydrolysis of BPC improved emulsion and/or foam-forming properties. However, for the hydrolysates prepared with Alcalase and Pepsin, an increasing DH generally decreased emulsifying and foam-forming capacities. Moreover, the type of enzyme impacted the resulting technofunctional properties. Hydrolysates prepared with Flavourzyme showed good technofunctional properties, independent of the DH. Physicochemical characterization of the hydrolysates indicated the importance of protein fragments with relatively high MW (exceeding 14.5 k) and high surface hydrophobicity for favorable technofunctional properties. 相似文献
19.
Ruíz-Henestrosa VP Sanchez CC Rodríguez Patino JM 《Journal of agricultural and food chemistry》2007,55(15):6339-6348
In this contribution, we have analyzed the effect of different strategies, such as change of pH (5 or 7) or ionic strength (at 0.05 and 0.5 M), and addition of sucrose (at 1 M) and Tween 20 (at 1 x 10(-4) M) on interfacial characteristics (adsorption, structure, dynamics of adsorption, and surface dilatational properties) and foam properties (foam capacity and stability) of soy globulins (7S and 11S at 0.1 wt %). We have observed that (1) the adsorption (presence of a lag period, diffusion, and penetration at the air-water interface) of soy globulins depends on the modification in the 11S/7S ratio and on the level of association/dissociation of these proteins by varying the pH and ionic strength (I), the effect of sucrose on the unfolding of the protein, and the competitive adsorption between protein and Tween 20 in the aqueous phase. The rate of adsorption increases at pH 7, at high ionic strength, and in the presence of sucrose. (2) The surface dilatational properties reflect the fact that soy globulin adsorbed films exhibit viscoelastic behavior but do not have the capacity to form a gel-like elastic film. The surface dilatational modulus increases at pH 7 and at high ionic strength but decreases with the addition of sucrose or Tween 20 into the aqueous phase. (3) The rate of adsorption and surface dilatational properties (surface dilatational modulus and phase angle) during adsorption at the air-water interface plays an important role in the formation of foams generated from aqueous solutions of soy globulins. However, the dynamic surface pressure and dilatational modulus are not enough to explain the stability of the foam. 相似文献
20.
Surface hydrophobicity of whey protein concentrate (WPC) under heated (85 degrees C for 5, 10, 20, 30, 40, and 60 min) and unheated conditions was measured using cis-parinaric acid (CPA), 1-anilino-8-naphthalenesulfonate (ANS), and a fluorescence quenching method using acrylamide as a quencher. This last method evaluates the degree of exposure of tryptophanyl residues in proteins to the solvent. The initial slope of Stern-Volmer plots, K(app), was used as an index of protein hydrophobicity. Surface hydrophobicity of WPC exhibited good relation with surface functional properties such as emulsifying and foaming. Analysis of the data obtained in this work showed that the fluorescence quenching method gave results similar to those obtained using CPA and ANS. Therefore, this simple technique is satisfactory in effectively obtaining information about the hydrophobicity of whey proteins. 相似文献