首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 875 毫秒
1.
This paper presents an experimental study on rolling shear (RS) strength properties of non-edge-glued cross-laminated timber (CLT) made out of New Zealand Radiata pine (Pinus radiata) structural timber. CLT specimens with 35 and 20 mm thick laminations were studied to evaluate the influence of lamination thickness on the RS strength of CLT. Short-span three-point bending tests were used to introduce high RS stresses in cross layers of CLT specimens and facilitate the RS failure mechanism. Modified planar shear tests from the conventional two-plate planar shear tests were also used to evaluate the RS strength properties. It was found that two test methods yielded comparable RS strength properties and the lamination thickness significantly affected RS strength of the CLT specimens. The test results also indicated that the recommended characteristic RS strength values of CLT products in Europe and Canada might be over conservative. Also, it might be more efficient to specify different RS strength values for CLT with different lamination thickness given the minimum width-to-depth ratio of laminations is satisfied.  相似文献   

2.
A model to predict bending stiffness of oriented strandboard (OSB) was tested with pilot plant experimental data. The experimental procedure developed in this study is unique in that it allows the model to be tested for extensive vertical configurations of strand angle distribution. After validation, the model was used to simulate a typical three-layer cross-oriented OSB panel with a vertical density profile and strand angle distribution measured on industrial panels. Analysis of the simulated vertical distribution of modulus of elasticity (MOE) indicated that the layers near the panel surfaces contributed much more to the effective parallel panel MOE than those close to the panel thickness center, with 80% of parallel MOE coming from the top 41% of weight and 32% of thickness. The effectiveness of methods to increase parallel bending stiffness through improving mat structure was evaluated. Increasing face/core weight ratio from 54/46 to 66/34 resulted in a 3.7% increase in simulated parallel MOE. Alignment of strands in face layers was identified having a greater potential to increase parallel MOE. Simulations with three improved strand angle distributions showed gains of 5.7, 12.0 and 19.8% in parallel MOE compared with a typical strand angle distribution of industrial OSB panels.  相似文献   

3.
The object of this study was to investigate the strength properties of edge-glued laminae and to propose a suitable grading method based on the lamina modulus of elasticity (MOE). Edge-glued laminae composed of lumber with similar MOEs (uniform laminae) and edge-glued laminae produced by randomly gluing lumber independent of MOE (random laminae) were made from karamatsu (Larix kaempferi) lumber having the same thickness and length, but various widths. For both the uniform and random laminae, there was a strong correlation between MOE values measured using the longitudinal vibration technique, the static bending test, and a grading machine. The average values of bending, tensile, and compressive strengths of the uniform laminae were similar to those of the random laminae. On the other hand, the average strength of laminae without end joints was significantly higher than that of finger-jointed laminae for both uniform and random laminae. Finger-joints and knots played a significant role in the failure of specimens, but the edge-gluing and the difference in MOE within an edge-glued lamina did not appear to affect the strength properties. The bending, tensile, and compressive strengths of edge-glued laminae were strongly correlated to the lamina MOE.  相似文献   

4.
Nail-head pull-through, lateral nail resistance, and single shear nailed joint tests were conducted on medium density fiberboard (MDF) with different density profiles, and the relations between the results of these tests and the density profiles of MDF were investigated. The maximum load of nail-head pull-through and the maximum load of nailed joints were little affected by the density profile. However, the ultimate strength of lateral nail resistance, the stiffness, and the yield strength of nailed joints were affected by the density profile of MDF and showed high values when the surface layer of the MDF had high density. It is known that bending performance is also influenced by density profile. Therefore, the stiffness and the yield strength of nailed joints were compared with the bending performance of MDF. The stiffness of nailed joints was positively correlated with the modulus of elasticity (MOE); in the case of CN65 nails, the initial stiffness of joints changed little in response to changes in MOE. The yield strength of nailed joints had a high positive correlation with the modulus of rupture (MOR). The stiffness and the yield strength of nailed joints showed linear relationships with MOE and MOR, respectively.  相似文献   

5.
Structural finger-jointed (FJ) lumber was used mainly in structural applications including glue-laminated beams and wooden I-joists and more recently in parallel chord wood trusses. The paper evaluated strength properties of structural FJ lumber by three nondestructive methods (edge-wise bending, longitudinal and transversal vibration) in order to find an alternative to traditional evaluation methods. Lumber was sawn from the logs following a pattern typically used in China to maximize the volume of recover...  相似文献   

6.
The effects of different thinning and pruning methods on the bending strength and dynamic modulus of elasticity (DMOE) of young Taiwania (Taiwania cryptomerioides Hay) were investigated. The average DMOE, modulus of elasticity (MOE), and modulus of rupture (MOR) in the thinning treatments showed the following trend: no thinning > medium thinning > heavy thinning. This indicates that thinning reduces average bending properties. The average DMOE, MOE, and MOR in the pruning treatments showed the following trend: medium pruning > no pruning > heavy pruning. According to this tendency, better average qualities of lumber and specimens were from wood subjected to no-thinning and medium-pruning treatments according to an ultrasonic wave technique and static bending tests. However, most results showed no statistically significant differences among thinning, pruning, and thinning and pruning treatments. The average values of DMOE, MOE, and MOR of visually graded construction-grade lumber were significantly greater than those of below-grade lumber. Moreover, there were very significant positive relationships between density, ultrasonic velocity, DMOE, MOE, and MOR, although the determination coefficients were small.  相似文献   

7.
This study established a prediction model for bending properties of glued-laminated timber (glulam) using optimized knot and modulus of elasticity (MOE) distributions of lumber laminate as the main input variables. For this purpose, knot and MOE data were investigated for all pieces of lumber that were prepared for glulam manufacturing, and statistical distributions of knot size, knot number in one lumber, and MOE of each laminate were optimized as distribution functions. These knot and MOE data were used as input variables in the prediction model for bending properties, and were also used in generating virtual glulam using the inverse transform method. Prediction of bending properties for glulam was carried out using the transformed section method, which is partially provided in ASTM D 3737 (Annex A4). Predicted values were compared with those from full-scale four-point bending tests for 60 six-layered glulams with 10 different laminar combinations. Finally, the allowable bending properties of glulam for each specific laminate combination were determined by calculating the fifth percentile of the modulus of rupture and the average modulus of elasticity from virtual test results of more than 1000 virtual glulams. From the results of this study, predicted bending properties for glulam and their distributions could be used for structural design in both allowable stress design and limit state design.  相似文献   

8.
AbstractThis study examined the performance of mechanically graded timber in bending when exposed to fire at various load ratios. The test specimens were 150 pieces, each with the dimensions of 60 × 120 × 3500mm. The modulus of elasticity (MOE) of 150 specimens was measured, and 60 among them were selected to formulate the prediction equation for MOE and modulus of rupture (MOR), which was used to predict the remaining 90 specimens. These were tested under fire exposure in bending using three-point loading at 11.1%, 16.7%, 33.3%, 66.7%, and 83.3% of the ultimate load. Using mechanically graded timber, which means acknowledging the actual strength of the bending member, permits fairly precise application to the targeted design load. This research confirmed that mechanically graded timber under fire exposure has the following tendencies: under the same load ratio, time to failure is independent of strength class, and, at any load ratio, the critical strength is dependent on the timber strength class. The obtained design bending strength under fire exposure using the reduced cross section method and the reduced strength method conformed to those calculated based on Eurocode 5. Following those findings, mechanically graded timber can be applied to obtain the design bending strength when taking into account the fire attack.  相似文献   

9.
This study investigated near-infrared spectroscopy (NIRS) to rapidly estimate physical and mechanical properties of No. 2 2 × 4 southern pine lumber. A total of 718 lumber samples were acquired from six mills across the Southeast and destructively tested in bending. From each piece of lumber, a 25-mm-length block was cut and diffuse reflectance NIR spectra were collected from the transverse face using a FOSS 5000 scanning spectrometer. Calibrations were created using partial least squares (PLS) regression and their performance checked with a prediction set. Overall moderate predictive ability was found between NIRS and the properties for the calibration and prediction sets: block specific gravity (SG) (R 2 = 0.66 and R p 2  = 0.63), lumber SG (0.54 and 0.53), modulus of elasticity (MOE) (0.54 and 0.58), and modulus of rupture (MOR) (0.5 and 0.4). Model performance for MOE (R p 2  = 0.70) and MOR (R p 2  = 0.50) improved when performing PLS regression on a matrix containing lumber SG and NIR spectra. Overall NIRS predicted MOE better than linear models using lumber SG (R 2 = 0.46), whereas lumber SG (R 2 = 0.51) predicted MOR better than NIRS. Overall NIRS has reasonably good predictive ability considering the small volume of wood that is scanned with the instrument.  相似文献   

10.
There have been many attempts to predict the performance of glulam beams. Several approaches have been taken, from early empirical techniques to more sophisticated stochastic methods. In recent years, more emphasis has been placed on the modeling of material properties. Generally, the modulus of elasticity (MOE) has been used as a criterion of laminar strength for the prediction of glulam performance in the traditional models. Most of the current models are based on MOE that was measured using the long span test; that is, they account only for variability between pieces of lumber. Therefore, these models do not account for the variation of material properties within a given piece of lumber. Five methods were considered to choose the appropriate one that could effectively predict the performance of glulam in this study. Prediction of glulam performance was done by the transformed section method. MOEs measured with the five methods were applied to a strength prediction program to compare the actual test results and the predicted results. MOEs used as input variables are as follows: long span MOE of the static bending test, localized MOE of the static bending test, long span MOE of the stress wave test, localized MOE of the stress wave test, and MOE of the machine stress rating (MSR) test. Results of the localized test showed excellent signification compared to those of the long span test. The MSR method, when used as input variable, obtained the most approximate result, so it is considered adequate for predicting the strength of glulam.An outline of this paper was presented at the 48th annual meeting of the Japan Wood Research Society, Shizuoka, April 1998  相似文献   

11.
To investigate the durability of structural laminated veneer lumber (LVL), outdoor exposure tests have been conducted since 1990 at a field-testing site at the Forestry and Forest Products Research Institute. This article is the second interim report on the results after 9 years of exposure. Seven kinds of structural LVL with no preservative treatment were subjected to the tests. Almost all the exposed specimens were decayed by a kind of brown rot fungi (Pseudomerulius aureus (Fr.) Julich). The degree of decay varied with wood species; grand fir and western hemlock LVL in particular showed weak resistance against the decay. All the specimens were stored for more than 1 year in a testing room conditioned at 20°C and 65% relative humidity. We then measured the ultrasonic velocity of the specimens by the Pundit method, penetration depth by the Pilodyn method, and bending strength by a conventional bending test. Correlation between nondestructive measurement factors and the density was strong even on LVL with many adhesive layers. The nondestructive testing method was found to be applicable to LVL as well as solid lumber. After the nondestructive measurements, each LVL was cut into three types of specimen (top: T, middle: M, and bottom: B) for the bending tests. The bending strength varied with the type of specimens. Correlation between modulus of elasticity and modulus of rupture was strong even in the decayed specimens.  相似文献   

12.
ABSTRACT

Cross laminated timber (CLT) is a wood panelling building system that is used in construction, e.g. for floors, walls and beams. Because of the increased use of CLT, it is important to have accurate simulation models. CLT systems are simulated with one-dimensional and two-dimensional (2D) methods because they are fast and deliver practical results. However, because non-edge-glued panels cannot be modelled under 2D, these results may differ from more accurate calculations in three dimensions (3D). In this investigation, CLT panels with different width-to-thickness ratios for the boards have been simulated using the finite element method. The size of the CLT-panels was 3.0 m × 3.9 m and they had three and five laminate layers oriented 0°–90°–0° and 0°–90°–0°–90°–0°. The thicknesses of the boards were 33.33, 40.0, and 46.5?mm. The CLT panel deformation was compared by using a distributed out-of-plane load. Results showed that panels with narrow boards were less stiff than wide boards for the four-sided support setup. The results also showed that 2D models underestimate the displacement when compared to 3D models. By adjusting the stiffness factor k88, the 2D model displacement became more comparable to the 3D model.  相似文献   

13.
In this study, the duration-of-load effect on the rolling shear strength of cross laminated timber (CLT), with different cross-sectional layups (five-layer and three-layer), was evaluated. A stress-based damage accumulation model is chosen to evaluate the duration-of-load strength adjustment factor of the rolling shear strength of CLT. This model incorporates the established short-term rolling shear strength of material and predicts the time to failure under arbitrary loading history. The model has been calibrated and verified based on the test data from low cycle trapezoidal fatigue tests (damage accumulation tests) in the previous study. The long-term rolling shear behaviour of CLT can then be evaluated from this verified model. As the developed damage accumulation model is a probabilistic model, it can be incorporated into a time based reliability assessment of the CLT products, considering short-term, snow, and dead load only loading cases. The reliability analysis results and factors reflecting the duration-of-load effect on the rolling shear strength of CLT are compared and discussed. The characteristic of this modeling theory lies in that the verified model is also able to predict the duration-of-load behaviour of CLT products under arbitrary loading history, such as long-term dead load case; then, these predictions of time to failure from the damage accumulation model can elucidate duration of load by the stress ratio evaluation approach. The results suggest that the duration-of-load rolling shear strength adjustment factor for CLT is more severe than the general duration-of-load adjustment factor for lumber; this difference should be considered in the introduction of CLT into the building codes for engineered wood design.  相似文献   

14.
Summary This study investigated the effect of Atropellis canker,Atropellis piniphila (Weir) Lohman and Cash, and stalactiform blister rust,Cronartium coleosporioides Arth., on the bending strength and stiffness of lumber from lodgepole pine,Pinus contorta Dougl. var.latifolia Engelm. The modulus of rupture, was unaffected by either disease. However, the modulus of elasticity (MOE) of lumber from infected trees, as determined by the Cook Bolinders and static bending tests, was significantly reduced from those of healthy trees. This impact should affect the use of lumber from infected trees when serviceability criteria govern the design of a structure. Should MOE-based, machine stress-rating of lumber become standard in the future, there may be an adverse, stress-related impact of these diseases on lumber value.We thank Mr. D. Hutcheson, B.C. Forest Service, Kamloops Region for advice and assistance, Messers, T. Jeanes, B. Geiselmann and D. Crabtree, Balco Forest Products Ltd., for advice, assistance, and particularly for harvesting and manufacture of the test material; Mr. L. Olsen, Forintek Canada Ltd. for assistance, and Dr. A. Harestad, Simon Fraser University for critical review. The research was supported in part by the Natural Sciences and Engineering Research Council, Canada, Operating Grant No. A3881  相似文献   

15.
Laminated strand lumber (LSL) and laminated veneer lumber (LVL) were thermally modified as a post-treatment at 140°C, 150°C, 160°C, 170°C, and 180°C. The tension modulus of elasticity (MOE) of LSL was not significantly impacted by the treatments, with the 180°C treatment group exhibiting the highest tension MOE (11.8?GPa). The LVL also experienced minimal impacts, with the 150°C treatment group having the highest tension MOE (19.4?GPa) and the 160°C treatment group exhibiting the lowest (17.1?GPa). The maximum tensile strength (MTS) of the LSL and LVL significantly decreased with increasing temperatures, with the control and 180°C treatment groups experiencing the highest and lowest MTS, respectively. The lowest MTS for LSL was 10.8?MPa (180°C treatment), which was 70% lower than the controls. The lowest MTS of the LVL was 24.4?MPa (also at the 180°C treatment), which was a 49% decrease compared to the controls. These results suggest that thermal-modification post-treatments minimally impact tension MOE, but can significantly reduce MTS at higher treatment temperatures. Combined with previous work improving the moisture properties and equilibrium moisture content of thermally modified LSL and LVL, it may be possible to optimize the treatment technique(s) to yield products with desirable properties.  相似文献   

16.
This work investigated some mechanical, physical and free formaldehyde emission properties of heat-treated MDF. For this purpose, MDF panels were subjected to varying heat treatment temperatures (155°C, 165°C and 175°C), durations (2.5?h., 3.5?h. and 4.5?h.) and waiting times after hot pressing (30?min., 120?min. and 600?min). Thickness swelling (TS), water absorption (WA), free formaldehyde emission (FFE), bending strength (BS), modulus of elasticity (MOE), tensile strength perpendicular to fibers (TSPF) for treated and untreated samples were tested and evaluated statistically. Consequently, after the heat treatment values of tensile strength, bending strength and modulus of elasticity were almost negatively affected relatively, but the thickness swelling and water absorption and quantities of free formaldehyde were improved positively of MDF samples.  相似文献   

17.
三种典型竹质工程材料纵向弹性模量评价   总被引：1，自引：1，他引：0  
以重组竹、竹束单板层积材（BLVL）、竹集成材为代表的竹质工程材料受到越来越多的关注和应用。文中采用超声波法、自由横向振动法和力学法分别对上述3种典型竹质工程材料的纵向动态弹性模量（MOE）进行评价比较,结果表明,横向自由振动法能较为快速、准确和无损地评价出竹质工程材料的MOE,MOE的变异系数与其自身铺装结构有关;重组竹、BLVL和竹集成材的一阶共振频率分别为455.73、380.41和487.62 Hz;超声波在竹集成材的纵向上传播速度最快,重组竹其次,BLVL最慢;三点弯曲力学测试发现3种竹质工程材料的断裂模式不同,全顺向的重组竹为竹纤维拉断和界面剪切破坏,纵横组坯的BLVL为横向竹束拉断以及竹/木复合界面分层,而更多体现实竹性能的竹集成材为底层竹材维管束拉断和拔出破坏,其断裂载荷为重组竹> BLVL >竹集成材,而断裂位移为竹集成材> BLVL >重组竹。  相似文献   

18.
Veneer drying is one of the most important stages in the manufacturing of veneer-based composites such as plywood and laminated veneer lumber. Due to the high drying costs, increased temperatures are being used commonly in plywood industry to reduce the overall drying time and increase capacity. However, high drying temperatures can alter some physical, mechanical and chemical characteristics of wood and cause some drying-related defects. In this study, it was attempted to predict the optimum drying temperature for beech and spruce veneers via artificial neural network modeling for optimum bonding. Therefore, bonding shear strength values of plywood panels manufactured from beech and spruce veneers dried at temperatures of 20, 110, 150 and 180 °C were obtained experimentally. Then, the intermediate bond strength values based on veneer drying temperatures were predicted by artificial neural network modeling, and the values not measured experimentally were evaluated. The optimum drying temperature values that yielded the highest bonding strength were obtained as 169 °C for urea formaldehyde and 125 °C for phenol formaldehyde adhesive in beech plywood panels, while 162 °C for urea formaldehyde and 151 °C for phenol formaldehyde in spruce plywood panels.  相似文献   

19.
The aim of this study was to develop a stochastic model for predicting the bending strength distribution of glued-laminated timber (GLT). The developed model required the localized modulus of elasticity (MOE) and tensile strengths of laminae as input properties. The tensile strength was estimated using a regression model based on the localized MOEs and knot area ratios (KAR) which were experimentally measured for lamina grades samples. The localized MOE was obtained using a machine stress-rated grader, and the localized KAR was determined using an image-processing system. The bending strength distributions in four types of GLTs were simulated using the developed GLT beam model; these four types included: (1) GLT beams without finger joints; (2) GLT beams with finger joints; (3) GLT beams with different lamina sizes; and (4) GLT beams with different combinations of lamina grades. The simulated bending strength distributions were compared with actual test data of 2.4 and 4.8 m-long GLTs. The Kolmogorov–Smirnov goodness-of-fit tests showed that all of the simulated bending strength distributions agreed well with the test data. Especially, good agreement was shown in the fifth percentile point estimate of bending strength with the difference of approximately 1%.  相似文献   

20.
The purpose of this study was to develop a cost-effective method to manufacture high-performance laminated veneer lumber (LVL) from mountain pine beetle (MPB)-affected veneers through partial resin impregnation and optimum board layup. Dry MPB-affected veneer sheets were segregated into two stress grades based on dynamic modulus of elasticity (MOE). A new phenol formaldehyde resin with a 30% solids content was formulated for resin impregnation. To reduce resin consumption, only veneer sheets used as outer layers were dipped in the resin for 5?min and then dried to manufacture 13-ply LVL. The bending properties, shear strength and dimensional stability of these LVL billets were examined and compared to those from the controls made from entirely untreated veneers. The results demonstrated that high-grade (E1) MPB-affected veneers had lower resin solids uptake than low-grade (E2) counterparts based on a 5?min dipping. Compared with the controls, the LVL billets made from resin-impregnated veneers for outer layers yielded increased surface hardness, significantly improved dimensional stability, shear strength and modulus of rupture on both edgewise and flatwise as well as better appearance with no cosmetic concerns. However, the improvement in LVL bending MOE was dependent on initial veneer stress grade. For high-grade (or density) E1 veneers, the use of impregnated veneers resulted in insignificant improvement in bending MOE. The optimum product layup was to place one ply of impregnated E1 grade veneer each for product face and back. By contrast, for low-grade (or density) E2 veneers, the use of impregnated veneers yielded a significantly higher flatwise bending MOE compared to the controls. The recommended product layup was the placement of two plies of impregnated E2 grade veneer sheets each for product face and back.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号