共查询到20条相似文献，搜索用时 713 毫秒
1.
北美规格材目测分等概述 总被引：1，自引：1，他引：0
目测分等方法是北美一种很重要的锯材分等体系, 即依据目测分等规则通过肉眼观测方式测定木材的缺陷状况进而确定规格材的材质等级。因此, 对木材缺陷与材质等级之间关系的正确把握以及对分等规则的正确应用, 是对规格材进行科学、正确分等的基本要求。合理地依据目测分等规则划分规格材等级, 不仅可以使规格材生产厂家的经济效益最大化, 而且有利于规格材产品使用性能的充分、合理发挥。经过目测分等的规格材具有客观的力学性质以及外观质量等级, 可以为其作为结构用材使用时提供科学的依据。直到今天, 目测分等方法依然是北美进行规格材分等的主要分等方法和基础。文中介绍了北美目测分等方法的发展、原理、意义以及世界上其他一些国家和地区的目测分等标准, 并对中国目测分等标准与北美目测分等规则进行了比较, 希望对完善我国的目测分等规则有所启示。 相似文献
2.
3.
4.
5.
原木等级及径级对规格材质量及出材率的影响 总被引：1，自引：1，他引：0
选用不同径级和质量等级的兴安落叶松原木,采用毛板下锯法和四面下锯法加工规格材,并检测分析了不同等级规格材的出材率。结果表明,原木径级在26～28cm时,规格材出材率较高;原木的等级与径级,及下锯法与原木径级交互因素,对规格材的出材率有显著的影响。要提高规格材出材率,应根据规格材尺寸优化匹配各因素。 相似文献
6.
研究指接、锯材等级对兴安落叶松结构用指接材弹性模量的影响,分析不同检测方法评估落叶松指接规格材弹性模量的可靠性。以落叶松锯材为原料,根据纵向基频振动(FFT)测试结果将其分为M_E12、M_E14、M_E16、M_E18四组,制备截面为40 mm×90 mm的规格材和指接规格材;分别利用纵向基频振动(FFT)、横向振动(TV)、机械应力分等级(MSR)测试评估指接材的静态弹性模量。结果表明:落叶松规格材和指接规格材是一种高弹性模量的锯材,其平均弹性模量大于SPF目测二级规格材的弹性模量;分级后,不同等级指接材弹性模量差异显著;指接加工降低中低等级锯材的弹性模量,但不影响高等级锯材的弹性模量;利用MSR测试结果评估指接材的弹性模量效果最佳,但其设备复杂,结合FFT设备的优点,推荐工厂使用FFT在线检测落叶松指接规格材的弹性模量。 相似文献
7.
采用GB 50005—2003（木结构设计规范》、日本JAS 1152（集成材日本农林标准》和美国ASTMD 245-2006《确立目测分等木材的结构等级及有关允许性能的标准规程》三个目测分等规则,对黑龙江产536根规格为4000mm×110mm×30mm的人工林落叶松锯材进行目测分等。结果表明,中国标准的目测分等结果与美国标准近似,而日本标准对木材材质要求最为严格。 相似文献
8.
9.
《林产工业》2014,(1)
以兴安落叶松刨光锯材制作胶合木指接层板,探讨指榫参数、指接压力和不同规格尺寸对锯材指接层板抗弯性能的影响。结果表明:指榫工艺参数对指接层板抗弯弹性模量影响较小,而对抗弯强度影响较大。当选用12.7、19mm和25mm指榫长度及其相应的指接工艺参数时,层板抗弯强度平均值和5%分位值均能达到国家标准GB/T 26899-2011《结构用集成材》目测分等Ⅰ_d等级和机械分等M_E14等级规定值,对于中小截面胶合木层板,尽可能考虑选用12.7~19mm范围内较小的指榫长度进行指接加工以利节材。在指接过程中应选用合适的指接压力,指接压力过大或过小都会对指接层板抗弯性能尤其强度造成不利影响,指接层板抗弯强度的尺寸效应与非指接锯材相似。 相似文献
10.
根据中国、日本和美国的外观分等标准对落叶松试材进行了以强度为基础的外观分等,并对试材进行了振动检测,分析比较了三国不同外观分等结果与振动检测的相关关系。 相似文献
11.
《Scandinavian Journal of Forest Research》2012,27(5):427-435
In Scandinavia, moose (Alces alces L.) sometimes cause severe browsing damage to economically-important pine. Moose-vehicle accidents have spurred construction of fences along roads, and these may interfere with moose migration between summer and winter ranges, or the road alone may be a barrier. If this happens and moose build up along roads, landowners may suffer economically. Therefore, this study investigated whether roads, fences or other factors influence the use of young pine stands by moose. Eighty stands along roads in northern Sweden were evaluated in which individually-browsed branches were counted on 9972 pines. Moose browsing was not significantly related to birch (Betula pendula Roth, B. pubescens Ehrh.) density, nor did it differ between pines (Pinus contorta Douglas or P. sylvestris L.). However, increased pine density, site productivity and proximity to a highway were associated with increased browsing. Further large-scale studies are needed to understand moose habitat selection and the effects of roads. 相似文献
12.
《Scandinavian Journal of Forest Research》2012,27(3):206-217
The root systems of 2-yr-old Picea glauca, Picea mariana and Pinus banksiana seedlings were submitted to various frost temperatures during an artificial frost to induce different levels of root damage. Frost-damaged and control seedlings were placed in a greenhouse under high and low soil moisture regimes. Seedling growth and physiology were evaluated periodically. Seedling survival was reduced when root damage reached levels of 60-80%. Root systems of all three species showed partial to total recovery by the end of the experiment. In general, root freezing damage caused reductions in seedling growth, with these reductions becoming less significant over time. Root damage had little to no effect on black spruce and jack pine seedling physiology, while white spruce CO 2 uptake decreased with increasing root damage. Shoot nitrogen content of all three species decreased slightly with increasing root damage. 相似文献
13.
Contour hedgerows of multipurpose tree species in the sloping tea lands of Sri Lanka are expected to reduce soil erosion and
also add significant amounts of plant nutrients to the soil via periodic prunings. The objective of this experiment was to characterize the biomass decomposition pattern and quantify the
amount of nutrients added through prunings of six tree species (Calliandra calothyrsus, Senna spectabilis, Euphatorium innulifolium, Flemingia congesta, Gliricidia sepium and Tithonia diversifolia) currently being used in hedgerows associated with tea. Withered leaf and stem prunings (50 g) were enclosed in 2-mm litter
bags, placed at 5-cm depth and retrieved after one, three, six, nine and 12 weeks. Loss of initial dry weight, N, P and K
was measured. Single exponential decay function adequately described both dry weight and nutrient loss. Tree species differed
significantly in their rate of breakdown with decomposition constants (k) varying from 0.0299 to 0.2006 week−1 for leaves and from 0.0225 to 0.0633 week−1 for stems. Gliricidia showed the highest k for leaves with the rest in the following descending order: Senna > Tithonia ≥ Euphatorium > Calliandra > Flemingia. A similar pattern was observed for loss of all nutrients with Calliandra and Flemingia always having lower k values than the rest. Although N immobilization was not observed, immobilization of P and K was observed
during the first week of incubation in some species, particularly in stem prunings. Annual biomass of prunings differed significantly
between tree species in the following descending order: Calliandra > Senna > Flemingia > Tithonia > Gliricidia > Euphatorium. Calliandra added the greatest amount of nutrients annually to the soil with Euphatorium adding the least. Calliandra prunings provided the annual total K requirement and 49% of the N requirement of mature tea. However, none of the species
provided more than 5% of the P requirement. It is concluded that among the tree species tested, Calliandra and Flemingia are the most suitable for contour hedgerows in tea plantations of this agroclimatic region because of their higher soil nutrient
enrichment capacity and slower decomposition rates which would minimize leaching losses.
This revised version was published online in June 2006 with corrections to the Cover Date. 相似文献
14.
《Scandinavian Journal of Forest Research》2012,27(2):118-130
The effects of seed weight and seed type on seedling growth of Pinus sylvestris (L.) were studied by seeding individually weighed orchard and stand seed in different mixtures under harsh (direct seeding in field) and optimal (seeding in nursery) conditions. In the nursery experiment an increase in the seed weight from 3 to 7 mg increased the seedling height by 10-27% and total weight by 27-113%, and decreased the height/diameter ratio by 5-6% after 2 yrs. With elimination of seed weight effects, orchard seedlings were 2% taller than stand seedlings in year 2. Without elimination of seed weight effects, orchard seedlings were 7-13% taller. In the field experiment an increase in the seed weight from 3 to 7 mg increased seedling height by 18-65%, stem volume by 81-274% and the number of top-buds by 23-34% in year 5. After elimination of seed weight effects, orchard seedlings were 7-13% taller than stand seedlings and without elimination of seed weight effects 20-21% taller after 5 yrs. Even after elimination of both seed weight and genetic effects orchard seedlings were 3-9% larger than stand seedlings in the field experiment. In conclusion, the influence of seed weight and seed type on growth traits and slenderness is highly significant and the influence seems to be greater in harsh conditions. 相似文献
15.
Steven Maranz Amadou Niang Antoine Kalinganire Djeneba Konaté Bocary Kaya 《Agroforestry Systems》2008,72(3):231-239
Baobab leaves form an important part of the local diet in Sahel countries and elsewhere in Africa. Existing leaf nutritional
data and agroforestry performance information are based solely on Adansonia digitata L., the baobab of continental Africa. The introduction potential of Adansonia species from the center of diversity in Madagascar and from Australia remains untapped. To assess this potential, the mineral
contents and B1 and B2 vitamin levels of dried baobab leaves were determined for five-year old trees of A. digitata, A. gibbosa (A. Cunn.) Guymer ex D. Baum, A. rubrostipa Jum. & H. Perrier (syn. A. fony Baill.), A. perrieri Capuron and A. za Baill. grown in an introduction trial in Mali. Nutritional data were evaluated against survival and vigor to identify promising
germplasm. Leaf vitamin and crude protein contents were highest in the Madagascar species, especially A. rubrostipa (B1 88 mg 100 g−1, B2 187 mg 100 g−1, protein 20.7% dry weight). However, the local species far outperformed the introductions in survival, tree height, basal
diameter and resistance to termites. We suggest grafting as a way of harnessing the vigor of well-adapted local baobab varieties
to the superior nutritional profiles of A. rubrostipa and others. Cross-species grafting tests in Adansonia were successful, thus creating new agroforestry possibilities with different scion/rootstock combinations. 相似文献
16.
《Wood material science & engineering》2013,8(2):76-84
Abstract Wood in general and wooden studs in particular are often distorted owing to uneven shrinkage during the drying process in the sawmill. Twist is often the most detrimental of all types of distortion, and it is caused by spiral grain in combination with variations in moisture content. For sawmills, the objective is to produce dried, straight boards, and one method of dealing with boards with excessive spiral grain is to sort them out and then dry them in a pretwisted position to obtain straight boards after drying. A model using the finite element (FE) method for the simulation of drying twist distortions was first calibrated against laboratory experiments in which boards were dried with and without restraints and pretwists. After the calibration, the FE results were compared with industrial test results for boards that were dried without restraints or with restraints with zero pretwist, i.e. straight restraints. The FE model used an elastic–ideally plastic material model to obtain permanent deformations. The calibration was to set the yield stresses so that there was a good match between FE results and results from the laboratory experiments. The comparison between the industrial test results and the FE results showed that the FE model is capable of realistic simulations of drying boards with and without restraints and presumably also pretwists. 相似文献
17.
Astra Zaluma Lauma Bruna Darta Klavina Natalija Burnevica Kristine Kenigsvalde Andis Lazdins Talis Gaitnieks 《Forest Pathology》2019,49(6)
Heterobasidion parviporum and Heterobasidion annosum are widely distributed root‐rot fungi that infect conifers throughout Europe. Infection of conifer stumps by spores of these pathogens can be controlled by treating fresh stumps with a competing non‐pathogenic fungus, Phlebiopsis gigantea. In this study, growth of three Latvian strains of P. gigantea and the biological control agent ‘Rotstop’ strain was evaluated in stem pieces of Norway spruce, Scots pine, lodgepole pine, Douglas‐fir, Weymouth pine, Siberian larch and Sitka spruce. The growth rates of one H. parviporum and one H. annosum isolate were also measured in the same stem pieces. The growth rate of P. gigantea varied greatly in wood of different conifer species. It was higher in the three pine species, lower in Norway spruce and lowest in Sitka spruce and Siberian larch, and in Douglas‐fir, this fungus did not grow. The largest area of wood occupied by P. gigantea was in lodgepole pine. Growth of Latvian isolates of P. gigantea in the wood of Pinus and Picea species was comparable to that of the Rotstop isolate. Consequently, stump treatment with local P. gigantea isolates should be recommended. However, our results suggest that Douglas‐fir stump treatment against Heterobasidion by P. gigantea may be ineffective and other stump treatment methods should be considered. 相似文献
18.
《Scandinavian Journal of Forest Research》2012,27(1):53-61
This study investigated the stand structure in pine, spruce and deciduous forests in the border district of Finland and Russia. A total of 46 mature forest stands was selected as pairs, the members of each pair being as similar as possible with respect to their forest site type, age, moisture and topography. The stands were then compared between the two countries by means of basal areas and number of stems. The proportions of dominating tree species were 2-12% lower, and correspondingly the proportions of secondary tree species higher, in Russian forests. The density of the forest stock was also higher in each forest type in Russia. The forests in the two countries differed most radically in terms of the abundance of dead trees. The amount was two to four times higher in Russian deciduous and spruce forests, and in pine forests the difference was 10-fold. The stand structures indicated that Russian coniferous stands, in particular, were more heterogeneous than intensively managed pine and spruce stands in Finland. 相似文献
19.
《Scandinavian Journal of Forest Research》2012,27(1):15-27
The root collar diameter and the height:diameter ratio are of particular importance in container-grown seedlings where a high density in the containers may produce spindly seedlings. Temperature regimes and light quality are known to affect plant growth. The aim of this study was to identify responses in Picea abies (L.) Karst. seedlings grown with light providing different red:far-red ratios and under temperature regimes with alternating day (DT) and night temperature (NT) from negative (DT < NT) to positive (DT > NT) difference (DIF) between DT and NT. Experiments were conducted in controlled environment chambers and in a daylight phytotron. Only limited thermoperiodic responses appeared in P . abies seedlings with respect to seedling height and dry weight accumulation. The formation of terminal buds, however, was clearly delayed in seedlings grown at negative DIF. The results indicate a requirement for day extension light that is high in far-red, to prevent terminal bud formation under natural short-day conditions. An extended study should be conducted to clarify the minimum level of light intensity and the optimal light quality needed to prevent terminal bud formation under natural short-day conditions. 相似文献
20.
本文分析了CAD在设计中引起的正面和负面影响,并进行了系统的阐述,从而使设计者在应用中能够保持客观的态度。 相似文献