首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 109 毫秒
1.
家具和地板用浸渍改性杉木研究进展   总被引:2,自引:0,他引:2  
杉木是我国南方重要的速生林树种之一,但其木材存在诸多缺陷,极大地限制了其在家具、地板中的进一步开发利用。将杉木进行浸渍改性以提高综合利用率是解决全球木材的供需矛盾和家具、地板用材短缺的重要手段之一。浸渍改性目前主要应用的树脂有UF树脂、PF树脂、聚乙烯醇缩甲醛、MF树脂等,其中以PF应用较常见,其改性效果较为显著。浸渍改性过程中,主要有真空处理、真空加压、抽提后常压浸渍或真空浸渍等浸注方法,辊压浸注作为常温常压条件下高效快速浸注处理木材的方法也可用于杉木的浸渍改性,真空-叠压法既能保证改性药剂完全渗入杉木木材,也能防止杉木试材在压力下被压溃。不同的浸渍工艺参数和树脂固化条件对改性后杉木性能影响不同:浸渍时间对浸渍材的吸水率及吸水厚度膨胀率影响较大,热压温度、热压时间与压缩变形恢复率、静曲强度密切相关,各工艺因素间存在一定的相互关系和影响。最后讨论了浸渍改性杉木在家具、地板业中的发展方向与应用前景,为杉木浸渍改性的进一步研究和应用提供参考。  相似文献   

2.
为探究浸渍纸层压木质地板翘曲变形的原因,从浸渍纸、地板基材以及热压工艺、平衡处理时间等因素选取变量,以不同水平组合制备强化木地板,按GB/T 18102—2007标准方法测试地板的翘曲度。结果表明:地板基材用纤维板的翘曲变形和密度,热压工艺中上、下热压板的温度差,以及浸渍纸的组合等因素,对强化木地板的翘曲变形存在不同程度的影响。  相似文献   

3.
浸渍后处理及干燥处理对木材树脂浸渍改性效果的影响   总被引:2,自引:0,他引:2  
【目的】探讨不同浸渍后处理方式和干燥方式对MUF树脂浸渍材增重率和尺寸稳定性的影响,为树脂浸渍改性技术提供参考和借鉴。【方法】利用5%、10%、15%和25%浓度的MUF树脂真空加压浸渍毛白杨木材,每种浓度树脂浸渍后试样首先分别进行4种方式浸渍后处理(气干处理7天、高湿度环境中平衡处理7天、树脂溶液中平衡处理7天以及不进行气干或平衡处理),然后分别利用2种干燥方式(直接干燥和湿干燥)进行干燥处理,干燥处理后测量不同处理条件下树脂浸渍材的增重率和容胀率,最后将素材和树脂浸渍材置于蒸馏水中常压浸渍14天,测试树脂浸渍材的抗胀率和径弦向差异湿胀程度。【结果】木材增重率与树脂浓度呈正相关关系,4种浓度树脂浸渍后试样增重率分别为9.7%、19.1%、28.4%和50.0%;不同浸渍后处理试样间的增重率差别不大;相同浸渍后处理条件下,直接干燥试样的增重率略低于湿干燥试样的增重率。树脂浸渍后,置于高湿度环境或树脂溶液中处理的试样,细胞壁容胀率较高;相同浸渍后处理条件下(除气干处理外),直接干燥试样的细胞壁容胀率低于湿干燥试样的细胞壁容胀率。树脂浸渍材抗胀率的变化规律与其细胞壁容胀率的变化规律基本一致。随着增重率增加,树脂浸渍材的径弦向湿胀率均降低,而其径弦向差异湿胀程度呈增加趋势,低增重率时试样的径弦向差异湿胀程度低于素材,而增重率超过30%左右时试样的径弦向差异湿胀程度高于素材。【结论】1)相同浓度树脂浸渍条件下,干燥方式对增重率的影响大于浸渍后处理方式,湿干燥处理有利于树脂在木材内部良好固着,从而获得更高的增重率;2)细胞壁容胀率受浸渍后处理方式和干燥方式二者的共同影响,置于高湿度环境或树脂溶液中的浸渍后处理有利于树脂继续扩散到木材细胞壁,湿干燥处理有利于树脂进一步扩散到木材细胞壁中并良好固着,从而对细胞壁产生更好的容胀效应;3)树脂浸渍材的抗胀率与细胞壁容胀率密切相关,树脂对细胞壁的容胀是树脂浸渍材尺寸稳定性提高的前提;4)树脂浸渍材的径弦向差异湿胀程度随增重率增加而有所增加。  相似文献   

4.
为满足卫浴装饰装修用木材的需求,以速生桦木为原料,开发出一种树脂浸渍单板重组材。通过分析浸渍三聚氰胺-甲醛(MF)树脂固体含量、浸渍方法、热压压力等因子对板材尺寸稳定性的影响,结果表明:当MF树脂固体含量45%、热压压力1.0MPa,采用辊压浸渍(压榨率50%~70%)时,板材的极限体积膨胀率为6.2%,低于水曲柳、栎木等实木试件,尺寸稳定性大大改善。  相似文献   

5.
采用真空-加压工艺对速生杨木进行低分子脲醛(UF)树脂浸渍改性,测试与分析浸渍工艺参数与浸渍改性后杨木增重率、力学强度的关系;并得出浸渍工艺最佳参数为:浸渍温度22~25℃、真空度0.07MPa下保持1h、压力0.6MPa下浸渍2h。  相似文献   

6.
速生杉木通过浸渍PF树脂并压缩改性后,力学性能得到大幅度提高,且随着树脂浓度和压缩率的增加而提高。增重率与真空度、浸渍压力、时间有关,并随着其增加而增大;抗胀(缩)率和阻湿率与树脂的浓度有关,当树脂浓度从0上升到10%时,ASE和MEE的值变化较大,当树脂浓度超过10%后趋于平缓;在树脂浓度相同的情况下,较大压缩的恢复率也相应较大,当树脂浓度低于10%时,随着浓度增加,恢复率急剧下降,浓度达到15%以上时,恢复率几乎没有变化。  相似文献   

7.
为改善三聚氰胺甲醛(MF)树脂贮存稳定性短及胶层脆性大等问题,利用蔗糖对浸渍薄木用MF树脂进行改性,研究改性剂蔗糖添加量与反应介质pH值对浸渍用MF树脂性能的影响,并利用傅里叶变换红外光谱仪对改性后蔗糖-三聚氰胺甲醛(SMF)树脂进行结构表征。结果表明:改性剂蔗糖的加入可以增强MF树脂的拉伸韧性及贮存稳定性,可使浸渍后的薄木顺纹拉伸强度提升到38.6 MPa;当蔗糖添加量为20%(与三聚氰胺质量比)、反应介质pH=8.0时,树脂贮存稳定性可达17 d,且浸渍薄木饰面后的三层杨木地板表面各项理化性能,均满足GB/T 18102—2007《浸渍纸层压木质地板》标准要求。  相似文献   

8.
天然有机物对速生杉木的改性研究   总被引:2,自引:0,他引:2  
采用天然有机物对速生杉木进行改性处理,经过改性处理的杉木的力学性能有很大提高。随着增重率的增大,处理材的各项力学性能均有较大提高。当增重率超过50%,处理材的表面硬度、顺纹抗压强度、抗弯强度和抗弯弹性模量提高将近1倍,表面耐磨耗性提高了3倍。这使杉木在力学性能上满足了木地板和家具面板制造的要求。  相似文献   

9.
湿法耐磨层技术在强化木地板生产中的应用   总被引:2,自引:1,他引:2  
李晓秀  周萍  淦洪 《林业科技》2001,26(3):43-44
浸渍纸层压木质地板(商品名称为强化木地板)源于欧洲,现流行于欧亚大陆,有蔓延全球之势,由于其所用原料和工艺的不同,其产品档次和性能差异较大,强化木地板是一层或多层专用浸渍纸铺装在刨花板、中密度纤维板、高密度纤维板等人造板基材表面,再在面层加上耐磨层、背面加平衡层浸渍纸,经热压而成的地板。  相似文献   

10.
采用自制的改性酚醛树脂浸渍处理松木单板,研究浸渍方式对其增重率和LVL性能的影响。结果表明:在30%PF树脂浓度,常温常压或加压条件下,增重率随时间的延长而增加;不同的浓度条件下,采用同一浸渍工艺,湿增重率先增后减,干增重率随浓度的增加而增加;增重率对LVL物理性能有明显影响,随着增重率的增大,单板层积材的密度逐渐增加,吸水厚度膨胀率(TS)与24 h吸水率逐渐下降。  相似文献   

11.

In Scandinavia, moose (Alces alces L.) sometimes cause severe browsing damage to economically-important pine. Moose-vehicle accidents have spurred construction of fences along roads, and these may interfere with moose migration between summer and winter ranges, or the road alone may be a barrier. If this happens and moose build up along roads, landowners may suffer economically. Therefore, this study investigated whether roads, fences or other factors influence the use of young pine stands by moose. Eighty stands along roads in northern Sweden were evaluated in which individually-browsed branches were counted on 9972 pines. Moose browsing was not significantly related to birch (Betula pendula Roth, B. pubescens Ehrh.) density, nor did it differ between pines (Pinus contorta Douglas or P. sylvestris L.). However, increased pine density, site productivity and proximity to a highway were associated with increased browsing. Further large-scale studies are needed to understand moose habitat selection and the effects of roads.  相似文献   

12.

The root systems of 2-yr-old Picea glauca, Picea mariana and Pinus banksiana seedlings were submitted to various frost temperatures during an artificial frost to induce different levels of root damage. Frost-damaged and control seedlings were placed in a greenhouse under high and low soil moisture regimes. Seedling growth and physiology were evaluated periodically. Seedling survival was reduced when root damage reached levels of 60-80%. Root systems of all three species showed partial to total recovery by the end of the experiment. In general, root freezing damage caused reductions in seedling growth, with these reductions becoming less significant over time. Root damage had little to no effect on black spruce and jack pine seedling physiology, while white spruce CO 2 uptake decreased with increasing root damage. Shoot nitrogen content of all three species decreased slightly with increasing root damage.  相似文献   

13.

This study investigated the stand structure in pine, spruce and deciduous forests in the border district of Finland and Russia. A total of 46 mature forest stands was selected as pairs, the members of each pair being as similar as possible with respect to their forest site type, age, moisture and topography. The stands were then compared between the two countries by means of basal areas and number of stems. The proportions of dominating tree species were 2-12% lower, and correspondingly the proportions of secondary tree species higher, in Russian forests. The density of the forest stock was also higher in each forest type in Russia. The forests in the two countries differed most radically in terms of the abundance of dead trees. The amount was two to four times higher in Russian deciduous and spruce forests, and in pine forests the difference was 10-fold. The stand structures indicated that Russian coniferous stands, in particular, were more heterogeneous than intensively managed pine and spruce stands in Finland.  相似文献   

14.

The root collar diameter and the height:diameter ratio are of particular importance in container-grown seedlings where a high density in the containers may produce spindly seedlings. Temperature regimes and light quality are known to affect plant growth. The aim of this study was to identify responses in Picea abies (L.) Karst. seedlings grown with light providing different red:far-red ratios and under temperature regimes with alternating day (DT) and night temperature (NT) from negative (DT < NT) to positive (DT > NT) difference (DIF) between DT and NT. Experiments were conducted in controlled environment chambers and in a daylight phytotron. Only limited thermoperiodic responses appeared in P . abies seedlings with respect to seedling height and dry weight accumulation. The formation of terminal buds, however, was clearly delayed in seedlings grown at negative DIF. The results indicate a requirement for day extension light that is high in far-red, to prevent terminal bud formation under natural short-day conditions. An extended study should be conducted to clarify the minimum level of light intensity and the optimal light quality needed to prevent terminal bud formation under natural short-day conditions.  相似文献   

15.
本文分析了CAD在设计中引起的正面和负面影响,并进行了系统的阐述,从而使设计者在应用中能够保持客观的态度。  相似文献   

16.

The effects of soil scarification (mounding), slash removal and clear-cut age on the natural regeneration in clear-cuts was evaluated using data from four sites in southern Sweden. The treatments were carried out during a good seed and establishment year for birch ( Betula pubescens Ehrh. and B. pendula Roth). Scarification had the strongest positive effect on the density of naturally regenerated seedlings, especially in birch, but also in pine ( Pinus sylvestris L.) and spruce [ Picea abies (L.) Karst]. Slash removal had a positive effect on birch density. No statistically significant effect of clear-cut age was found. In addition, no statistically significant interactions between clear-cut age and scarification or slash removal were found. The ingrowth of field vegetation was the fastest in areas that were not scarified, less rapid in areas scarified on old clear-cuts, and the slowest after scarification in fresh clear-cuts. In conclusion, it may be possible to control the density of birch during a good establishment year for birch. If birch is desired, the best combination of treatments is to remove the slash and scarify; otherwise, these treatments should be avoided.  相似文献   

17.
18.

Based on an enquiry, risk perception among non-industrial private forest owners is described in relation to climate change and forestry hazards. Of the respondents, 11% took action to remedy the effects of climate change. Out of a given set, hazards were ranked according to each respondent's experience of recent substantial financial loss to the estate and in relation to his or her willingness to make investments aimed at risk reduction. For each hazard, the respondent assessed the risk in four classes ranging from very high to negligible risk. Six hazards were considered most problematic in all three aspects: browsing damage, falling timber prices, damage by wind, spruce bark beetle, root rot and pine weevil. A majority of the respondents claimed to take action to reduce the risk associated with at least one hazard, while 35% did not know whether they did. Excluding climate change, the need for decision support was the largest in relation to damage by wind owing to a combination of perceived high risk and a high level of ignorance in relation to whether risk-reducing measures were taken.  相似文献   

19.
In situ produced plant residues contain a mixture of different plant components of varying quality. To assess synergistic or antagonistic interactions occurring during the decomposition and mineralization of such mixtures, individual plant parts (stems, leaves, leaf litter and roots) or the mixture of stems, leaves and leaf litter of the agroforestry species pigeonpea (Cajanus cajan) or of crop residues of peanut (Arachis hypogaea) or of the weed hairy indigo (Indigofera hirsuta) were incubated in pots for 19 weeks. Periodically, remaining plant residues were sieved out (>2 mm), weighed and N content as well as soil mineral N determined. Above- and below-ground residues of peanut decomposed fastest and showed the largest N release in agreement with their high N concentration and low-acid detergent fibre (ADF) : N ratio. Hairy indigo was hypothesized to be of lower quality than pigeonpea because of its high-polyphenol content. However, it decomposed faster than pigeonpea, largely because of the higher N and lower lignin concentration of its components. Ranking of individual plant components for N mineralization resulted in the following pattern, leaves > leaf litter > roots > stems. In mixtures of the different plant components a similar species order in decomposition was obtained, e.g. peanut > hairy indigo > pigeonpea. The amount of N released from the mixture was dominated by stem material that comprised 46–61% of the mixture. The interactions in mixtures were relatively small for peanut (generally high-quality components) as well as for pigeonpea (low proportion of high-quality components, i.e. N rich leaf material). However, a positive interaction occurred during later stages of N mineralization in the mixture of hairy indigo as it had a significant proportion of N rich components and absence of highly reactive polyphenols. Thus, for plants with low to intermediate chemical quality attributes, manipulating plant composition (e.g. by varying harvest age, affecting stem and leaf proportions) will be important to obtain significant interactions during decomposition when its components are mixed.  相似文献   

20.
The use of organic waste materials such as milk sewage as an organic fertilizer could have the dual advantages of organic-waste disposal and reduced dependence on inorganic fertilizers. The effects of fertilization with (1) conventional mineral fertilization, (2) milk sewage sludge at 40 kg N ha−1 target rate and (3) no fertilization on pasture production and tree growth were examined in an experiment consisting of two pasture mixtures under a one-year-old Pinus radiata plantation with a density of 2500 trees ha−1. The two pasture mixtures were: (1) Dactylis glomerata L. var. saborto (25 kg ha−1) + Trifolium repens L. group Ladino (4 kg ha−1) + Trifolium pratense L. var. Marino (1 kg ha−1); (2) Lolium perenne L. var. Tove (25 kg ha−1) + Trifolium repens L. group Ladino (4 kg ha−1) + Trifolium pratense L. var. Marino (1 kg ha−1). The experiment began in the spring of 1995 using a randomized block design with three replicates in Castro Riberas de Lea (Lugo, Galicia, north-western Spain). Plot size was 12 × 8 m2, with a 1 m buffer strip between plots. Two-year data showed that fertilization with either material had a positive effect on pasture production, with no significant difference between the two fertilization treatments. Tree growth in the milk sewage sludge plot was significantly higher than in the control plots. Inorganic fertilization increased pasture production, but affected tree growth negatively. The results show that milk sewage sludge could be used as a fertilizer in silvo-pastoral systems. This revised version was published online in June 2006 with corrections to the Cover Date.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号