首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 15 毫秒
1.
In this paper, viscose rayon-based knitted fabrics were utilized as the precursor to produce activated carbon fiber absorbents (ACFA). The effects of carbonization and activation conditions on characteristics (ACFA) were examined. Experimental results revealed that increasing the flow rate of environmental gas N2 and steam activator used in conjunction and decreasing the production rate of ACFA can obtain better pore properties. However, higher flow rate of steam activator and lower production rate of ACFA reduced the weight yield. According to our findings, to maintain good absorption property of ACFA, the optimum manufacturing conditions are flow rate of gas N2 at 80 cc/min, flow rate of steam activator at 60 ml/min, and production rate of ACFA at 30 cm/min, with flame retardant reagent concentration maintained at 30%. Under these conditions, the weight yield can be up to 40.85% and the BET surface area can exceed 1500 g/m2.  相似文献   

2.
In this study, two kinds of polyacrylonitrile (PAN) (carbon fiber grade PAN and oxidized fiber grade PAN) are used as the raw materials for a PAN-based nanofiber nonwoven that is prepared using electrospinning. A high-temperature erect furnace is then used, which uses oxidization processes to prepare oxidized nanofiber nonwovens in a continuous manufacturing process. The parameters used for the oxidation process are oxidation temperatures of 150, 200, 250, 275, 300 and 300 °C, which correspond to a production rate of 3, 5 and 10 cm/min at 5-cN tension. The variation in the yield rate, the breaking strength and the shrinkage of the oxidized PAN based electrospun nonwovens are examined in this study. The results demonstrate that the limit oxygen index (LOI) and aromatization index (AI) increase as the production rate decreases. Under the optimum oxidation conditions, higher quality oxidized electrospun nonwovens are produced using carbon fiber grade PAN with AI of 61 % and LOI of 42 %.  相似文献   

3.
This study uses rayon woven fabrics as the raw material for activated carbon fabrics (ACFs), which were manufactured by oxidation, carbonization and activation engineering in a continuous semi-open high-temperature furnace. First, the activated carbon fabrics are prepared under two specific manufacturing conditions with different production rates and flow rates of steam activation at 1000 °C. Then the electrochemical prosperities of the ACFs are evaluated by a three-electrode device. The experimental results show that the BET specific surface area and electrical capacitance are higher with a lower production rate. Moreover, the steam activator higher flow rate under the proposed approach. ACFs with a 2332.1 m2/g specific surface area and 78.7 % mesopore ratio result in a higher electronic conductivity of 430.4 F/g at the low rate charge (5 mV/s) and with 60 % capacitance retention during the high-speed charging-discharging process (100 mV/s).  相似文献   

4.
Continuously twisted polyacrylonitrile/viscose nanofiber core-spun yarns were fabricated through novel self-designed multi-nozzle air jet electrospinning set-up. The effect of voltage, solution flow rate, air flow rate and funnel rotating speed on coating rate of core-spun yarn, nanofiber diameter, twist level and mechanical property were discussed. The results showed that polyacrylonitrile/viscose nanofiber core-spun yarns with perfect nanofiber orientation and uniform twist distribution could be obtained at voltage of 32 KV, solution flow rate of 32 ml/min and air flow rate of 1000 ml/min, and the spinning speed could reach to 235.5 cm/min. The diameters of outer coated nanofiber distributed from 100 nm to 300 nm, and nanofiber coating rate could reach to 70.4 %. In addition, the strength and elongation at break increased from 30.82 MPa to 69.65 MPa and from 28.34 % to 43.29 % at the twist angle of 46.6 °, respectively.  相似文献   

5.
Electrospinning is a simple and cost-effective method to prepare fiber with nanometer scale. More importantly, 3D flexible nanofiber yarns that fabricated by electrospinning have shown excellent application prospects in smart textiles, wearable sensors, energy storage devices, tissue engineering, and so on. However, current methods for preparing electrospinning nanofiber yarns had some limitations, including low yarn yield and poor yarn structure. In this paper, a stepped airflow-assisted electrospinning method was designed to prepare continuously twisted nanofiber yarn through introducing stepped airflow into traditional electrospinning system. The stepped airflow could not only help to improve nanofiber yield, but also good for controlling the formed nanofibers to be deposited in a small area. In addition, the experimental methods of single factor variables were used to study the effects of stepped airflow pressure, applied voltage, spinning distance, solution flow rate, air pumping volume and friction roller speed on nanofiber yarn yield, nanofiber diameter, yarn twist and mechanical property. The results showed that prepared nanofiber yarns exhibited perfect morphologies and the yield of nanofiber yarn could reach to a maximum of 4.207 g/h. The breaking strength and elongation at break of the prepared yarn could reach to 23.52 MPa and 30.61 %, respectively.  相似文献   

6.
In order to realize flexible organic light emitting diode (OLED), it is critically important to protect moisture and oxygen penetration into the flexible device through the polymer substrates because of intrinsically poor stability of organic materials of OLED to moisture. Since complete protection of the moisture penetration is almost impossible, moisture absorbents are used inside OLED. In this study, metal oxide/polymer hybrid nanofiber with mechanical flexibility and efficient moisture absorption capability was fabricated by electrospinning. Hydrophilic poly(vinyl pyrrolidone) (PVP) or hydrophobic poly(vinylidenefluoride) (PVDF) and calcium oxide (CaO) were used as the fiber forming polymers and as the moisture absorbing particle, respectively. Polymers were first dissolved in appropriate solvents and CaO was then dispersed in the prepared polymer solutions. The hybrid solution was then electrospun, producing the hybrid nanofiber web looking like paper with thickness of about 100 µm. It was observed that all CaO particles were uniformly held by the nanofiber. It was also observed that only a small portion of the surface of CaO particles was covered by fiber since the fiber diameter was much smaller than the CaO particle size. This implied effective moisture absorption through the free surface of CaO. The hybrid nanofiber absorbed moisture very efficiently upto about 70 % of the nanofiber mass. Once moisture was absorbed by the nanofiber, it was never released even at 150 °C in vacuum for 2 hours. It is, therefore, expected that the nanofiber may be applied as the flexible thin moisture absorbent to improve stability of the flexible OLED.  相似文献   

7.
Silk fibroin (SF)/Cellulose Acetate (CA) blend nanofibrous membranes were prepared by electrospinning and their heavy metal absorbabilities were examined in an aqueous solution after ethanol treatment. The electrospun nanofibrous membranes were comprised of randomly oriented ultrafine fibers of 100–600 nm diameters. As a result of field emission electron microscope (FEEM), the anti-felting properties of the blend nanofibrous membranes were markedly improved after treatment with 100 % ethanol when SF was blended with CA. Metal ion adsorption test was performed with Cu2+ as a model heavy metal ion in a stock solution. The SF/CA blend nanofiber membranes showed higher affinity for Cu2+ in an aqueous solution than pure SF and pure CA nanofiber membranes. Especially, the blend nanofibrous membranes with 20 % content of CA had an exceptional performance for the adsorption of Cu2+, and the maximum milligrams per gram of Cu2+ adsorbed reached 22.8 mg/g. This indicated that SF and CA had synergetic effect. Furthermore, the parameters affecting the metal ions adsorption, such as running time and initial concentration of Cu2+, had been investigated. The results showed that the adsorption of the Cu2+ sharply increased during the first 60 min, the amount of metal ions adsorbed increased rapidly as the initial concentration increased and then slope of the increase decreased as the concentration further increased. This study provides the relatively comprehensive data for the SF/CA blend nanofibrous membranes application to the removal of heavy metal ion in wastewater.  相似文献   

8.
Textile sound absorbents are getting more and more popular on the market as noise reduction is a major requirement for human comfort today. In this paper we focus on a new textile material for sound absorption, by investigating the acoustic characteristics of nanofibers. Through impedance tube method we measured the sound absorption coefficients of multiple layers of nanofiber webs and compared those with microfiber materials per fabric weight. We also examined the effect of layers of nanofiber webs on regularfiber knitted fabric on sound absorption. The test results showed that the sound absorption coefficients of nanofiber layers were superior that of microfiber fabrics in the frequency range 1000–4000 Hz. In this range, the sound absorption of nanofiber webs improved with numbers of layers. Also, adding nanofiber web plies to regularfiber fleece increased the sound absorption coefficient with 85 % at 4000 Hz. From our results we could observe differences in the sound absorption coefficients between two test methods, which are higher absorbance coefficients through the reverberation room method than impedance tube method.  相似文献   

9.
In the present study, nano-sized Pt/WO3-carbon nanofiber, Pt-Pd/WO3-carbon nanofiber and Pt-Ru/WO3-carbon nanofiber electrocatalysts were synthesized and the performance of prepared catalysts were compared with catalysts coated carbon black for the oxygen reduction reaction (ORR). The morphology and structure of prepared catalysts were characterized using scanning electron microscopy (SEM) and X-ray diffraction (XRD) analysis. The SEM images showed that the catalyst nanoparticles were well dispersed on the both carbon nanofiber and carbon black supports. Electrochemical measurements including linear sweep voltammetry (LSV), electrochemical impedance spectroscopy (EIS) and chronoamperometry (CA) tests were applied to investigate the potential of the fabricated electrodes on the ORR. The results demonstrated that the catalysts based on carbon nanofibers showed a significant increase of activity toward the ORR. Also, the Pt/Pd coated carbon nanofibrous electrode showed the highest electrochemical activity.  相似文献   

10.
The nanofiber membrane prepared by electrospinning has been widely applied in lithium-ion batteries. A powerful strategy for designing, fabricating and evaluating Poly-m-phenylene isophthalamide (PMIA) nanofiber membrane with SiO2 nanoparticles was developed by electrospinning in this paper. The morphology, crystallinity, thermal shrinkage, porosity and electrolyte uptake, and electrochemical performance of the SiO2/PMIA nanofiber membranes were investigated. It was demonstrated that the nanofiber membrane with 6 wt% SiO2 possessed notable properties, such as better thermal stability, higher porosity and electrolyte uptake, resulting in higher ionic conductivity (3.23×10-3 S·cm-1) when compared with pure PMIA nanofiber membrane. Significantly, the SiO2/PMIA nanofiber membrane based Li/LiCoO2 cell exhibited more excellent cycling stability with capacity retention of 95 % after 50 cycles. The results indicated that the SiO2-doped PMIA nanofiber membranes had a potential application as separator in high temperature resistance lithium-ion batteries.  相似文献   

11.
In this study, polyacrylonitrile was used as the nanofiber membrane material. Through A two-stage continuous process, namely, oxidation process and carbonization and activation process, an activated nanofiber membrane material was fabricated. Subsequently, the membrane underwent high-temperature heat treatment (1100-1500 °C) to explore the effect of temperature on its properties. Charge/discharge rate was employed to determine the capacitance retention ratio to evaluate the applicability of the fabricated membrane in high-power super capacitor electrodes. The results revealed that in the treated membrane, the lattice size increased from 1.24 nm to between 3.20 and 4.72 nm. In addition, the volume resistivity was reduced from 6 Ω-cm to between 9.70E-2 and 3.85E-2 Ω-cm, substantially improving the electric conductivity. The activated carbon nanofiber membrane treated with high temperature at 1100 °C exhibited the highest capacitance of 704 F/g at a scan rate of 5 mV/s.  相似文献   

12.
In this study, electrospun wool keratose (WK)/silk fibroin (SF) blend nanofiber was prepared and evaluated as a heavy metal ion adsorbent which can be used in water purification field. The WK, which was a soluble fraction of oxidized wool keratin fiber, was blended with SF in formic acid. The electrospinnability was greatly improved with an increase of SF content. The structure and properties of WK/SF blend nanofibers were investigated by SEM, FTIR, DMTA and tensile test. Among various WK/SF blend ratios, 50/50 blend nanofiber showed an excellent mechanical property. It might be due to some physical interaction between SF and WK molecules although FTIR result did not show any evidence of molecular miscibility. As a result of metal ion adsorption test, WK/SF blend nanofiber mats exhibited high Cu2+ adsorption capacity compared with ordinary wool sliver at pH 8.5. It might be due to large specific surface area of nanofiber mat as well as numerous functional groups of WK. Consequently, the WK/SF blend nanofiber mats can be a promising candidate as metal ion adsorption filter.  相似文献   

13.
花生壳残渣制备活性炭及吸附性能测定   总被引：1，自引：0，他引：1  
杨莉  谢宇  邱贤华  邓磊 《花生学报》2010,39(2):16-20
用提取黄酮后废弃的花生壳做原料,选择不同的活化剂在一定温度下制备活性炭,并且测定其吸附性能。结果表明：磷酸作为活化剂时活性炭产率最高,达39.5%;当炭化温度为500℃、活化剂为氢氧化钾或磷酸、活化剂浓度为10%时,碘吸附值最高,为966.7mg/g;当炭化温度为500℃、活化剂浓度为10%时,几种活化剂制备出来的活性炭亚甲基蓝脱色力均达到40mL/g左右;与几种市售活性炭比较,花生壳活性炭碘吸附值能够满足市场需要,但是亚甲基蓝脱色力偏低;相同条件下,盐作为活化剂所制备出的活性炭对镍离子的吸附能力比较稳定。  相似文献   

14.
Porous nanocomposites are prepared by electrospinning blended polyacrylonitrile, copper acetate and mutiwalled carbon nanotube in N, N-dimethylformamide. The electrospun nanofiber webs are oxidatively stabilized and then carbonized resulting in composite carbon nanofibers. The study reveals that composite nanofibers with relatively smooth surface morphology are successfully prepared. X-ray diffraction is used to confirm the presence of Cu in carbon nanofibers. The carbon nanofibers with CNTs have better thermal stability and higher electrical conductivity. The Brunauer-Emmett-Teller analysis reveals that C/Cu/CNTs nanocomposites with mesopores possess larger specific surface area and narrower pore size distribution than that of C/Cu nanofibers. The electrochemical properties are investigated by cyclic voltammetry and galvanostatic charge-discharge tests. The nanocomposite with 0.5 wt.% CNT loading exhibits an energy density of 2 Whkg?1, power density of 1916 Wkg?1, a specific capacitance of about 225 Fg?1 at a current density of 2 Ag?1 and its capacitance decreased to 78 % of its initial value after 3,000 cycles.  相似文献   

15.
A pitch precursor for a general purpose carbon fiber was prepared by condensation of pyrolized fuel oil (petroleum residual oil) with bromine under nitrogen blowing. Such a condensation raised the softening point of the pitch from 40°C to 265°C with a yield of 43%. The pitch precursor showed an enhanced aromaticity and enlarged molecular size, which led to a reduction in molecular mobility and optical isotropy. The precursor was spun into fibers of 20 μm diameter at a take-up speed of 700 m/min. The fiber was stepwise stabilized in air and carbonized in Ar gas to obtain an isotropic carbon fiber. The carbon fiber exhibited tensile strengths of 500–800 MPa though the fiber was formed via a crude method. The electric conductivity of the carbon fiber was relatively high, 2.2×102 S/cm, sufficient to be used as electrode materials.  相似文献   

16.
Wet electrospinning is a simple and efficient method to manufacture continuous nanofiber filaments. However, polyacrylonitrile nanofiber filaments collected using a static water bath are limited for application in certain areas due to their low degree of alignment and breaking stress values. To improve these properties, a novel countercurrent flowing liquid bath collector was combined with a multi-needle electrospinning device. The morphologies, crystalline structures, thermal behaviors and mechanical properties of filaments fabricated under different countercurrent bath liquid motion conditions were investigated. In addition, the forces acting on the nanofibers in the bundling triangular zone under countercurrent liquid bath motion were analyzed. The results showed that the average nanofiber diameter of the filaments decreased with an increase in bath solution motion forces. The maximum alignment degree and breaking stress of the nanofibers were 85 % and 0.63 cN/dtex, respectively, achieved using a liquid flow rate of 80 ml/min and water inlet diameter of 6 mm. The alignment degree of the assembled nanofibers in the bundling triangular zone could be increased by 57 % when using a countercurrent flowing liquid compared with a static liquid bath.  相似文献   

17.
Nanofibers definitely hold great advantage and promise in filtration as they have very high specific surface area, which ensures greater probability of capturing the particles and hence, the filtration efficiency of the nanofiber filter media is high. Electrospun nanofibers are prohibitively expensive due to extremely low production rate. With recent advances in melt blowing technology, nanofibers could be produced at production rate few orders of magnitude higher than that of conventional single syringe electrospinning and hence, quite cost effective. Influence of air pressure and die to collector distance (DCD) were studied on the number average fiber diameter for the nanofibers as well as the performance properties of the nonwoven webs, each factor at three discrete levels. The nanofibers were as fine as 260 nm. A very encouraging observation of the study is very high values of quality factor observed for nanofiber nonwoven filter media. In order to compare the filtration efficiency of different nanofiber nonwoven media samples with different basis weight, a novel term of specific filtration efficiency is proposed and was found that the specific filtration efficiency with the increase in DCD or air pressure.  相似文献   

18.
Cellulase production is one of the most critical steps in the economics of second generation ethanol. Although solid-state fermentation (SSF) is an attractive process for the production of enzymes, SSF is highly limited by the difficulty in controlling the operating variables which affect microbial growth and metabolites production. In this context, this work evaluates the effects of operational conditions on endoglucanase production by a selected strain of Aspergillus niger cultivated under SSF using an instrumented lab-scale bioreactor equipped with an on-line automated monitoring and control system. The effects of air flow rate, inlet air relative humidity and substrate initial moisture on endoglucanase production were evaluated using a statistical design methodology. A correlation coefficient of 0.9106 and a calculated value of F, 5.46 folds higher than the listed value (P-value < 0.05) allowed the modeling of endoglucanase production under different process conditions. Higher endoglucanase production (56.1 U/g) was achieved for a selected condition of substrate initial moisture of 72%, air inlet humidity of 70%, and flow rate of 20 mL/min. A significant increase in endoglucanase production was also found to be achieved under forced aeration conditions (50.2 IU/g) compared to static conditions (29.8 IU/g) after 72 h of cultivation. Besides, respirometric analysis revealed that the total amount of CO2 produced was linearly correlated with enzyme production (R2 of 0.988). The bioreactor system used, as well as the methodology employed herein, was very effective in evaluating the influence of operational variables on enzymes production under SSF.  相似文献   

19.
In the present study, conducting nanofillers are incorporated in thermoplastic polyurethane (TPU) to produce nanocomposite fibers through melt compounding route using micro twin screw extruder attached to a fiber drawing device. Nanocomposite fibers using bulk graphite, nanographite and carbon nanofiber were produced using varying amounts of these nanofillers. Metal coated nanographite, new hybrid nanoparticle produced in house, were also used to impart conductivity to the TPU fiber. The process parameters such as processing temperature, mixing time and rpm of the screw have been optimized considering minimum change in TPU bulk properties. It has been found that the nanofillers can be melt mixed safely up to 4 min with the TPU at 180 °C and 100 screw rpm. These mixing conditions give reasonable amount of dispersion. The studies on such fibers in differential scanning calorimetry (DSC) and thermomechanical analyzer (TMA) reveals that the metal coated nanographite particles make the nanocomposite fibers more thermally stable. Both the D. C. conductivity and A. C. impedance of the nanocomposite fibers have reduced significantly even at very low loading of nanofillers, although the conductivity of the produced fibers are in antistatic range (D.C. conductivity ～10?4 S/m).  相似文献   

20.
Crypthecodinium cohnii is a marine heterotrophic dinoflagellate that can accumulate high amounts of omega-3 polyunsaturated fatty acids (PUFAs), and thus has the potential to replace conventional PUFAs production with eco-friendlier technology. So far, C. cohnii cultivation has been mainly carried out with the use of yeast extract (YE) as a nitrogen source. In the present study, alternative carbon and nitrogen sources were studied: the extraction ethanol (EE), remaining after lipid extraction, as a carbon source, and dinoflagellate extract (DE) from recycled algae biomass C. cohnii as a source of carbon, nitrogen, and vitamins. In mediums with glucose and DE, the highest specific biomass growth rate reached a maximum of 1.012 h−1, while the biomass yield from substrate reached 0.601 g·g−1. EE as the carbon source, in comparison to pure ethanol, showed good results in terms of stimulating the biomass growth rate (an 18.5% increase in specific biomass growth rate was observed). DE supplement to the EE-based mediums promoted both the biomass growth (the specific growth rate reached 0.701 h−1) and yield from the substrate (0.234 g·g−1). The FTIR spectroscopy data showed that mediums supplemented with EE or DE promoted the accumulation of PUFAs/docosahexaenoic acid (DHA), when compared to mediums containing glucose and commercial YE.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号