首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 826 毫秒
1.
We report the preparation of polybenzoxazole (PBO) fiber from polyhydroxyamide (PHA) precursor fiber which is free from strong acid such as polyphosphoric acid. We prepared the PHA fibers with different spin-draw ratios (SDRs) using a wet-spinning method and the PBO fibers with an SDR of 3.5 (SDR-3.5 PBO fibers) were prepared by various heat-treatment temperatures, and investigated their morphology, crystalline structure, and mechanical properties. The simultaneous thermogravimetric analysis-mass spectrometry (STA-MS) and field-emission scanning electron microscopy (FE-SEM) results confirmed that the diameter of the SDR-3.5 PBO fiber was much smaller than that of the SDR-3.5 PHA fiber, due to the release of water during the thermal cyclization reaction which forms the PBO structure. The wide-angle Xray diffraction (WAXD) pattern of the SDR-3.5 PBO fiber heat-treated at 350 °C (SDR-3.5 PBO 350 fiber) showed two peaks, at 2θ=14.83 ° and 24.38 °, and the diffraction angles dropped with increasing heat-treatment temperature. In addition, the initial modulus and tensile strength of the SDR-3.5 PBO fiber heat-treated at 550 °C (SDR-3.5 PBO 550 fiber) were found to be 19.1 GPa and 449.2 MPa, which were much higher than those of the SDR-3.5 PHA fiber, 9.3 GPa and 227.0 MPa, respectively.  相似文献   

2.
A new application of conventional electroless nickel plating to improve the interfacial properties of PBO fibers was reported. The relationship between surface morphology and interfacial properties of nickel-plated PBO fiber was explored. The continuous nickel coating consisted of nickel and phosphorus elements determined by Energy dispersive spectrometer (EDS) and transmission electron microscope (TEM), exhibiting high adhesive durability. The influence of bath temperature and plating time on the crystal structure, microstructure and mechanical properties of nickel-plated PBO fibers was systematically investigated. X-ray diffractometer (XRD) results revealed that the crystal structure among nickel-plated PBO fibers did not show differences. Scanning electron microscope (SEM) and Atomic force microscope (AFM) images showed that the process parameters had a great influence on surface morphology and roughness of nickel-plated PBO fibers, which could directly affect the interfacial properties of nickel-plated PBO fibers. Single fiber pull-out testing results indicated that the interfacial shear strength (IFSS) of PBO fibers after electroless nickel plating had a significant improvement, which reached maximum at 85 °C for 20 min. Single fiber tensile strength of nickel-plated PBO fibers was slightly lower than that of untreated one. Thermo gravimetric analysis (TGA) indicated that nickel-plated PBO fiber had excellent thermal stability.  相似文献   

3.
The application of poly (p-phenylene-2, 6-benzobisoxazole) (PBO) fiber as reinforcement in composite material was restricted by its photo-degradation, therefore, some measures should be considered to protect PBO fiber against UV aging. In this study, A series of multilayer coating for (POSS/TiO2)n was prepared on PBO fiber surface via LbL assembly technique for enhancement of UV resistance. TiO2 as UV absorbing material was used to relieve UV-degradation of PBO. Surface elemental composition, surface morphology, mechanical and interfacial properties, and UV resistance of uncoated and coated PBO fibers were investigated. These experimental results show multilayer coating of (POSS/TiO2)n was uniform deposition on fiber surface after treatment, tensile strength decreased to certain extent, interfacial shear strength increased in a small range and UV resistance is obvious enhanced. After the same accelerated aging time under UV irradiation, the retention of tensile strength and intrinsic viscosity of coated PBO fibers were much better than that of untreated PBO fibers.  相似文献   

4.
1-Ally-3-methylimidazolium chloride ([AMIM]Cl) was successfully synthesized and was used as a green spinning solvent for cellulose. The celluloses of various degrees of polymerization (DP) were dissolved in the [AMIM]Cl to obtain 5 % (w/w) cellulose solutions, which were regenerated to cellulose fibers through wet spinning process. Of three different regenerated cellulose fibers with different DPs, a DP of 2,730 was gave the strongest regenerated fiber without drawing having a tensile strength of 177 MPa and an elongation at break of 9.6 % respectively, indicating that celluloses of higher molecular weight can be entangled and oriented more easily. Also maximum draw ratio of the as-spun fibers increased from 1.2 to 1.7 with increasing degree of polymerization leading to a tensile strength and modulus of 207 MPa and 48 GPa, respectively. Particularly the tensile modulus was substantially higher than those of lyocell and high performance viscose fibers of 20 GPa or less. The higher DP of pristine cellulose was critical in increasing the mechanical properties such as tensile strength and elongation at break of the as-spun fibers coupled with higher tensile modulus after drawing.  相似文献   

5.
The surface topography, tensile properties, and thermal properties of ramie fibers were investigated as reinforcement for fully biodegradable and environmental-friendly ‘green’ composites. SEM micrographs of a longitudinal and cross-sectional view of a single ramie fiber showed a fibrillar structure and rough surface with irregular cross-section, which is considered to provide good interfacial adhesion with polymer resin in composites. An average tensile strength, Young’s modulus, and fracture strain of ramie fibers were measured to be 627 MPa, 31.8 GPa, and 2.7 %, respectively. The specific tensile properties of the ramie fiber calculated per unit density were found to be comparable to those of E-glass fibers. Ramie fibers exhibited good thermal stability after aging up to 160°C with no decrease in tensile strength or Young’s modulus. However, at temperatures higher than 160°C the tensile strength decreased significantly and its fracture behavior was also affected. The moisture content of the ramie fiber was 9.9%. These properties make ramie fibers suitable as reinforcement for ‘green’ composites. Also, the green composites can be fabricated at temperatures up to 160°C without reducing the fiber properties.  相似文献   

6.
This article describes a new process for strengthening natural silk fibers. This process is simple yet effective for mass production of high strength silk fibers, enabled by drawing at a lower temperature and immediately heat setting at a higher temperature. The processing conditions were investigated and optimized to improve the strength. Silk fibers drawn to the maximum ratio at room temperature and then heat set at 200 °C show best tensile properties. Some salient features of the resulting fibers are tensile strength at break reaching 533±10.2 MPa and Young’s modulus attaining 12.9±0.57 GPa. These values are significantly higher than those of natural silk fibers (tensile strength increased by 44 % and Young’s modulus by 135 %). Wide-angle X-ray diffraction and FTIR confirm the transformation of silk I to silk II crystalline structure for the fiber obtained from this process. DSC and TGA data also provide support for the structural change of the silk fiber.  相似文献   

7.
Green composites from Pattawia pineapple leaf fiber (PALF) and poly(lactic acid) (PLA) were prepared. The mechanical method was chosen to extract PALF from fresh leaves due to this method gave high yield of fiber, short extraction time, and environmental friendly. Tensile and thermal properties, together with morphology of the fibers were disclosed. The fibers were conducted into a specified length of 1–3 mm and blended with PLA, using a twin screw extruder, with the PALF content of 10–50 wt%. Tensile testing, morphology investigation and thermogravimetric analysis were applied. Preliminary results showed that tensile modulus of the composites depended on PALF content. The tensile modulus and elongation at break of the composite containing 40 % PALF was about 48 %, and 111 % increase, respectively, compared with that of PLA. With addition of maleic anhydride coupling agent, such the composite showed the tensile modulus of 5.1 GPa, which was 34 % higher than that of the non-coupling agent composite, and about 104 % higher than that of PLA. Although the elongation at break of the composite containing 40 % PALF was found to dramatically increase by 111 %, the introduction of maleic anhydride in such the composite caused only 57 % increase in the elongation at break compared with that of PLA. Finally, a pilot product of square boxes was produced successfully from the proposed composite, by conventional injection molding process.  相似文献   

8.
The tensile-recoil compressional behavior of the carbon nanotube reinforced mesophase pitch (MP)-based composite carbon fibers (CNT-re-MP CFs) was investigated by using Instron and SEM. The CNT-re-MP CFs exhibited improved, or at least equivalent, compressive strength as compared with commercial MP-based carbon fibers. Particularly, when CNT of 0.1 wt% was reinforced, the ratios of recoil compressive strengths to tensile strength of CNT-re-MPCFs were much higher (the difference is at least 10% or higher) than those for the commercial counterparts and even than those for PAN-based commercial carbon fibers. FESEM micrographs showed somewhat different fractography from that of a typical shear failure as the CNT content increased.  相似文献   

9.
In order to improve the interfacial adhesion property between Poly(p-phenylene benzobisoxazole) (PBO) fiber and epoxy, the surface modification effects of PBO fiber under dielectric barrier discharge treatments in different time were investigated. The samples were tested for surface morphology, functional groups, surface wettability and interfacial shear strengths (IFSS) in epoxy using scanning electron microscope, Fourier transform infrared spectroscopy, water contact angle measurements and Micro-bond pull out tests, respectively. The results indicated that fiber surface morphology after plasma treatment was rougher than untreated one. Some polar groups were introduced on fiber surface in plasma treatment. Moreover, surface wettability and the IFSS between fiber and epoxy had much improvement after plasma treatment, the contact angle decreased with the treatment time increasing and reached the lowest value when the treated time was 60 s, and the IFSS was improved by 117.3 %. On the other hand, no significant difference in single fiber tensile test was observed between treated and untreated fibers when the processing time was shorter than 75 s, but the tensile strength declined by more than 10 % after 75 s treatment as a result of the excessive plasma etching.  相似文献   

10.
In order to develop composites with better mechanical properties and environmental performance, it becomes necessary to increase the hydrophobicity of the natural fibers and to improve the interface between matrix and natural fibers. Graft copolymerization of natural fibers is one of the best methods to attain these improvements. Only few workers have reported the use of graft copolymers as reinforcing material in the preparation of composites. So in the present paper, we report the preparation of graft copolymers of flax fibers with methyl acrylate (MA) using Fenton’s reagent (FAS-H2O2) as redox system. Synthesized flax-g-poly(MA) was characterized with FTIR, TGA/DTA, scanning electron microscopy (SEM), and X-ray diffraction (XRD) techniques. Composites were prepared using flax-g-poly(MA) as a reinforcement and phenolformaldehyde (PF) as the binding material. Mechanical properties of phenol-formaldehyde composites were compared and it has been found that composites reinforced with flax-g-poly(MA) showed improvement in mechanical properties. Composites reinforced with flax-g-poly(MA) showed better tensile strength (235 N) and compressive strength (814 N) in comparison to composites reinforced with original flax fiber which showed lesser tensile strength (162 N) and compressive strength (372 N). Composites reinforced with flax-g-poly(MA) shows the improved MOR, MOE, and SP.  相似文献   

11.
Fiber-reinforced plastic (FRP) is composed of reinforced fibers and matrix resin, and has high specific strength and low-density materials. Because of the orientation of the fibers within them, FRPs are prone to buckling damage when under compression along the axial direction of the fiber, especially flexible organic ones. The compressive performance of FRP is largely dependent on fiber properties. the buckling load of FRP will increase with the increasing of fiber’s. In this study, we developed a way to improve the compressive and bending strength of ultra-high molecular weight polyethylene (UHMWPE) fibers. Carbon nanotubes (CNTs) and vapor-grown carbon fibers (VGCFs) were coated on the surface of UHMWPE fibers by pyrrole vapor deposition. The transverse compressive strength and bending strength of single UHMWPE fibers were determined by microcompression and single fiber bending measurements, respectively. The experiment result showed that coating UHMWPE fibers with CNTs and VGCFs increased both their transverse compressive strength and bending strength. It is excepted that the improved fiber would applied in FRP for better compressive performance.  相似文献   

12.
A commercially available polyester resin was reinforced with cabuya fibers. The experimental variables were the fiber loading and the length of the fiber. Tensile strength, flexural strength, and the Izod impact resistance were measured for the samples and compared to the polyester resin performance without reinforcement. Mechanical properties of the cabuya fiber reinforced material were also compared with the same resin but reinforced with glass fibers. An increase in fiber load decreases the tensile strength for the cabuya reinforced composite, where a value of 52.6 MPa corresponded to the tensile stress of the resin without reinforcement and a value of 34.5 MPa for the best reinforcement achieved with cabuya. An increase in both fiber load and length increases the Young’s modulus of the cabuya reinforced material, and a maximum value of 2885 MPa was obtained. The Young’s modulus and impact resistance values for the cabuya composite (2885 MPa and 100.87 J/m, respectively) reached higher values than those obtained for non-reinforced polyester material (2639 MPa and 5.82 J/m, respectively), and lower than the glass fiber composite (5526 MPa and 207.46 J/m, respectively); while the tensile and flexural strength obtained for the cabuya composite (34.5 MPa and 32.6 MPa, respectively) were lower than the unreinforced (52.6 MPa and 62.9 MPa, respectively) and glass fiber reinforced polyester (87.3 MPa and 155 MPa, respectively).  相似文献   

13.
Poly(ethylene terephthalate) (PET) copolymers containing fluorenylidene bis(2-phenoxyethanol) (FBPE) were prepared. The glass transition temperature of copolymers increased continuously with the composition of FBPE. The glass transition temperature of PET/FBPE copolymer at loading of 15 mol% FBPE was 107 °C, which was 35 °C higher than that of PET. The melting temperature of PET/FBPE copolymers was decreased with the composition of FBPE, and it disappeared above 6 mol% of FBPE. The heat deflection temperature of copolymers increased from 60.7 °C for PET to 89.9 °C for the copolymer containing 15 mol% of FBPE. The values of optical transmittance of copolymers were 89-90 % at 550 nm, and no significant change was observed with the FBPE composition. The impact strength value of copolymer at loading of 10 mol% FBPE was 26 J/m, which was 20 J/m higher than that of PET.  相似文献   

14.
Cassava bagasse is an inexpensive and broadly available waste byproduct from cassava starch production. It contains roughly 50% cassava starch along with mostly fiber and could be a valuable feedstock for various bioproducts. Cassava bagasse and cassava starch were used in this study to make fiber-reinforced thermoplastic starch (TPSB and TPSI, respectively). In addition, blends of poly (lactic acid) and TPSI (20%) and TPSB (5, 10, 15, 20%) were prepared as a means of producing low cost composite materials with good performance. The TPS and PLA blends were prepared by extrusion and their morphological, mechanical, spectral, and thermal properties were evaluated. The results showed the feasibility of obtaining thermoplastic starches from cassava bagasse. The presence of fiber in the bagasse acted as reinforcement in the TPS matrix and increased the maximum tensile strength (0.60 MPa) and the tensile modulus (41.6 MPa) compared to cassava starch TPS (0.40 and 2.04 MPa, respectively). As expected, blending TPS with PLA reduced the tensile strength (55.4 MPa) and modulus (2.4 GPa) of neat PLA. At higher TPSB content (20%) the maximum strength (19.9 MPa) and tensile modulus (1.7 GPa) were reduced about 64% and 32%, respectively, compared to the PLA matrix. In comparison, the tensile strength (16.7) and modulus (1.2 GPa) of PLA blends made with TPSI were reduced 70% and 51% respectively. The fiber from the cassava bagasse was considered a filler since no increase in tensile strength of PLA/TPS blends was observed. The TPSI (33.1%) had higher elongation to break compared to both TPSB (4.9%) and PLA (2.6%). The elongation to break increased from 2.6% to 14.5% by blending TPSI with PLA. In contrast, elongation to break decreased slightly by blending TPSB with PLA. Thermal analysis indicated there was some low level of interaction between PLA and TPS. In PLA/TPSB blends, the TPSB increased the crystallinity of the PLA component compared to neat PLA. The fiber component of TPSB appeared to have a nucleating effect favoring PLA crystallization.  相似文献   

15.
Present research investigates the mechanical properties of jute-coir fiber reinforced hybrid polypropylene (PP) composite with fiber loading variation and observes the effect of chemical treatment of fiber on property enhancement of the composites. Composites were manufactured using hot press machine at four levels of fiber loading (5, 10, 15 and 20 wt%). Fiber ratio’s were varied (jute:coir=1:1, 3:1 and 1:3) for 20 % fiber loaded composites. Both jute and coir fiber was treated using 5 % and 10 % NaOH solutions. Composites were also prepared using treated fiber with jute-coir fiber ratio of 3:1. Tensile, flexural, impact and hardness tests and Fourier transform infrared spectroscopic analysis were conducted for characterization of the composites. Tensile test of composite showed a decreasing trend of tensile strength and increasing trend of the Young’s modulus with increase in fiber loading. During flexural, impact and hardness tests, the flexural strength, flexural modulus, impact strength and hardness values were found to be increased with increase in fiber loading. All these properties enhanced with the enhancement of jute content except impact strength. 5 % NaOH treatment provided an improving trend of properties whereas, 10 % NaOH treatment showed the reverse one. The FTIR analysis of the composites indicated decrease of hemicelluloses and lignin content with alkali treatment.  相似文献   

16.
In the present study, nanofibrils of cellulose are extracted from waste jute fibers using high energy planetary ball milling process in wet condition. The rate of refinement of untreated fibers having non-cellulosic contents was found slower than treated fibers due to strong holding of fiber bundles by non-cellulosic contents. At the end of three hours of wet milling, untreated fibers were refined to the size of 850 nm and treated fibers were refined to the size of 443 nm. In the subsequent stage, composite films of poly lactic acid (PLA) were prepared by solvent casting with 3 wt% loading of untreated jute nanofibrils, treated jute nanofibrils and microcrystalline cellulose. The influence of non-cellulosic contents on mechanical properties of PLA films are investigated based on results of tensile test, dynamic mechanical analysis and differential scanning calorimetry. The maximum improvement was observed in case of treated jute nanofibril/PLA composite film where initial modulus and tensile strength increased by 207.69 % and 168.67 %, respectively as compared to neat PLA film. These improvements are attributed to the increased interaction of treated jute nanofibrils with PLA matrix due to their higher precentage of cellulosic contents and mechanically activated surface.  相似文献   

17.
Composites were prepared with 13, 23 30 and 40 % fiber and evaluated the mechanical performance in tensile, flexural and impact. The mechanical properties of these composites were also evaluated function of time at 110 °C thermal exposure. Caroa fibers were characterized by techniques such as thermal gravimetric analysis (TGA), X-ray diffraction (XRD) and scanning electron microscopy (SEM). It was found that the best mechanical properties were achieved for composites containing 23 to 30 % fiber. The incorporation of 23 % fiber caroa increased both the modulus of elasticity in the tensile test as the flexural strength and impact, the composite with 30 % fiber caroa showed higher tensile strength. The results show that the tensile and flexural strength of the composite decreased with time of thermal exposure. The thermal aging at 110 °C caused a decrease in tensile properties of the composites.  相似文献   

18.
Intra-layer and inter-layer hybrid composite laminates were made with epoxy resin and compositions were varied in six different proportions. In-plane compressive mechanical properties were studied using finite element analysis and experiments, and the results found were in good agreement. Properties of intra-layer and inter-layer hybrids were compared with plain carbon/epoxy and plain glass/epoxy composites, and a comparison among themselves was also made. It was found that intra-layer hybrids to some extent exhibit better compressive properties compared to inter-layer hybrids. Percentage enhancement in compressive failure strain was noticed. Negative hybrid effects on compressive strength was noticed for both intra-layer and inter-layer hybrid configurations. It was found that proportion of carbon fiber content plays a key role in determining the compressive properties. According to macro-scale observation all composite laminates failed catastrophically under compressive loading. SEM observation depicted that under compressive loading carbon fibers break first followed by glass fiber.  相似文献   

19.
Most materials used in daily life are polymeric materials based on petrochemistry. The used polymeric materials can cause land pollution and air pollution after landfill or incineration. In contrast, natural fiber reinforced (NFR) composites are more suitable for the environment, however the reliability in terms of the durability and weatherability of NFR composites is still lacking. Thus, NFR composites require the reliability involved with durability and weatherability. In this work, poly(butylene terephthalate-co-glutarate) (PBTG), with a chemical structure similar to biodegradable PBAT, was used as the matrix in the composites, and hemp fibers were used as the reinforcement. Hemp/PBTG composites were fabricated by stacking hemp-fiberwebs and PBTG films with various fiber contents and thermal exposure times. Characteristics of the composites, such as the morphological structure, chemical structure, tensile properties, compressive properties, flexural properties, and impact strength, were analyzed to obtain the effects of fiber volume fraction and thermal exposure. As a result, hemp/PBTG composites were hardened in proportion to fiber volume fractions, and the hardening behavior of the composites increased tensile strength and flexural strength. However, the hardened structure of the composites decreased the impact strength and compressive strength of the composites. On the other hand, the mechanical properties of hemp/PBTG composites with thermal exposure times, were governed significantly by the brittleness behavior of the resin and the increased crystallinity of hemp fibers. Thus, the hemp fibers contributed to the improvements on structural stability, tensile strength and flexural strength of the hemp/PBTG composites, and increased the thermal durability of the composites with various thermal exposures.  相似文献   

20.
The physical properties of natural growth fibers such as chemical composition content and fiber diameter are highly affected by environmental issues such as environmental changes and fiber extraction methods. These irregularities of the natural fibers seriously affect its utilization in composite as reinforcements. In this study, taking into account the importance of the fiber tensile strength, the correlation degrees between the kenaf fiber tensile strength and the fiber chemical composition, crystallinity, orientation degree were analyzed by the grey relational analysis method. Both the kenaf single fiber and fiber bundle were used as XRD and tensile strength test sample. The chemical composition content and the FTIR were carried out to obtain a correct result of the chemical composition content. It found that for the different XRD and tensile strength test samples, the single fiber showed lower crystallinity, higher orientation degree and tensile strength compared with the fiber bundle. The cellulose content and the orientation degree got the higher correlation degree with single fiber tensile strength, which was 0.674 and 0.640. The highest factor associated with the fiber bundle tensile strength was the orientation degree, the correlation degree was 0.747. The hemicellulose content and the crystallinity also got high correlation degree with the fiber bundle strength, which was 0.687 and 0.640.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号