首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 32 毫秒
1.
Sugar palm fiber is one of the most abundant natural fibers used in biocomposites. However, prediction of the mechanical properties of such natural fiber reinforced composites is still challenging. Most of the theoretical modelings are based the micromechanical method. There have been little studies involving statistical approach for prediction of mechanical properties of natural fiber reinforced composites. In this study, the tensile properties of short sugar palm fiber-reinforced high impact polystyrene (SPF-HIPS) composites obtained by means of statistical approach were investigated and compared with the experimental observations and with micromechanical models available in the literature. Statistical approach was used to predict the performance of the composite part with different fiber loadings. A two-parameter Weibull distribution function was used to model the fiber length distribution in the composite. For the experimental validation, the composites were prepared by hot compression technique for different fiber loadings (10 %, 20 %, 30 %, 40 % and 50 % by weight). Tensile testing of the composites was carried out according to ASTM D638 to obtain the composites tensile strength and modulus of elasticity. Experimental results showed that the tensile strength of the composite reduced due to the addition of sugar palm fibers, whereas the elastic modulus increased by a factor of up to 1.34. The current statistical model predicted the tensile properties of SPF-HIPS composite close to the experimental values. It was found that statistical approach with standard micromechanical models can be used to predict the mechanical properties of sugar palm fiber reinforced HIPS composites. Hence, this study could assist in decisions regarding the design of natural fiber reinforced composite products.  相似文献   

2.
Denim, a twilled cotton fabric, was used to enhance the mechanical and thermal properties of poly(lactic acid) (PLA). The denim fabric reinforced composites with different numbers of denim layers were fabricated by using a hand layup method. The impact, tensile, and dynamic mechanical properties of the composites were observed with increasing denim layers to examine the reinforcing effect of denim fabrics. Numerical analysis was carried out to model the elastic modulus of the composite by using a commercial software. Three-dimensional geometry of the denim fabric reinforced PLA composite was generated through a CAD program, and the elastic modulus was calculated by applying uniform deformation on one surface. The impact strength, tensile strength, and thermal properties of the composites were improved by piling denim fabrics. The denim fabric reinforced composites exhibited outstanding impact strength due to the retarded crack propagation as well as large energy dissipation. The 3 layer denim reinforced composite showed best results among all specimens, and its impact strength, tensile strength, and tensile modulus were measured to be 82 J/m, 75.76 MPa, and 4.65 GPa, respectively. The PLA/denim composites have good mechanical properties and can substitute traditional composites such as glass fiber or carbon fiber reinforced composites.  相似文献   

3.
The current study examines the tribological performance of poly(vinylidene fluoride) (PVDF) and carbon fiber reinforced PVDF (CF/PVDF) under dry sliding condition. Different contents of carbon fibers were employed as reinforcement. All filled and unfilled polyimide composites were tested against CGr15 ball and representative testing was performed. The effects of carbon fiber content on tribological properties of the composites were investigated. The worn surface morphologies of neat PVDF and its composites were examined by scanning electron microscopy (SEM) and the wear mechanisms were discussed. Moreover, all filled PVDFs have superior tribological characteristics to unfilled PVDFs. The optimum wear reduction was obtained when the content of carbon fiber is 20 vol %.  相似文献   

4.
A series of the long glass fiber reinforced thermoplastic polyurethane elastomers and poly (styrene-acrylonitrile) (LGF/TPU/SAN) composites with different contents of long glass fiber were prepared by using self-designed impregnation device. Dynamic mechanical properties of TPU/SAN matrix reinforced with 10, 20 and 30 % by weight long glass fibers have been investigated by using dynamic mechanical thermal analysis (DMA). The results indicated that the content of long glass fiber and scanning frequency had some influence on dynamic mechanical properties and glass transition of LGF/TPU/SAN composites. In addition, the Arrhenius relationship has been used to calculate the activation energy of a-transition of the LGF/TPU/SAN composites. SEM demonstrates the relatively good dispersion of the long glass fiber in the TPU/SAN matrix. In addition, Effects of the content of long glass fiber on mechanical properties of the LGF/TPU/SAN composites are investigated.  相似文献   

5.
Fragrant screwpine fiber reinforced unsaturated polyester composites (FSFRUPC) were subjected to water immersion tests in order to examine the effect of water absorption on the mechanical properties. FSFRUP composite specimen containing 30 % fiber volume fraction with fiber length of 3 mm and 9 mm was considered in this study. Water absorption test was performed by immersing specimen in sea, distilled and well water at room temperature under different time durations (24, 48, 72, 96, 120, 144, 168, 192, 216, 240 hours). The tensile, flexural and impact properties of the water absorption specimen were appraised and compared with those of the dry composite specimen as per the ASTM standard. The tensile, flexural and impact properties of FSFRUPC specimen were found to decrease with the increase in the percentage of moisture uptake. The percentage of moisture uptake of composite was reduced after alkali treatment with 3 % NaoH for 3 hours. In moisture absorption test, the lowest diffusion coefficient, D (6.62513×10-13 m2/s) and swelling rate parameter, K sr (6.341×10-3 h-1) were obtained through the specimen immersed in sea water. The chemical composition, elemental composition of fiber and surface morphology of the FSFRUPC were analysed by using Fourier transform infrared spectroscopy (FTIR), Energy dispersive spectroscopy (EDS) and scanning electron microscopy (SEM) respectively.  相似文献   

6.
Natural fibers are largely divided into two categories depending on their origin: plant based and animal based. Plant based natural jute fiber reinforced polypropylene (PP) matrix composites (20 wt% fiber) were fabricated by compression molding. Bending strength (BS), bending modulus (BM), tensile strength (TS), Young’s modulus (YM), and impact strength (IS) of the composites were found 44.2 MPa, 2200 MPa, 41.3 MPa, 750 MPa and 12 kJ/m2, respectively. Animal based natural B. mori silk fiber reinforced polypropylene (PP) matrix composites (20 wt% fiber) were fabricated in the same way and the mechanical properties were compared over the silk based composites. TS, YM, BS, BM, IS of silk fiber reinforced polypropylene composites were found 55.6 MPa, 760 MPa, 57.1 MPa, 3320 MPa and 17 kJ/m2 respectively. Degradation of composites in soil was measured upto twelve weeks. It was found that plant based jute fiber/PP composite losses its strength more than animal based silk fiber/PP composite for the same period of time. The comparative study makes it clear that mechanical properties of silk/PP composites are greater than those values of jute/PP composites. But jute/PP composites are more degradable than silk/PP composites i.e., silk/PP composites retain their strength for a longer period than jute/PP composites.  相似文献   

7.
The concept of reinforcing soil with natural fibers was originated in ancient times. However, short natural and synthetic fiber soil composites have recently attracted increasing attention in geotechnical engineering for the second time. Consequently in this work, shear behavior of fiber reinforced soil composite was modeled by using force-equilibrium method. The proposed model indicated that fiber percentage, fiber diameter, fiber aspect ratio, Elastic Modulus of fiber, coefficient of friction between fiber and matrix, the thickness of shearing zone and vertical compressive stress determine the shear resistance of a fiber reinforced soil composite. In the next step, a set of laboratory direct shear tests was performed on different samples including both neat soil and fiber reinforced treatments. In order to compare model outputs and experimental results, it was necessary to measure the coefficient of friction between fiber and soil. Therefore, a novel apparatus based on fiber pull-out test was designed to determine the interfacial shear stress between fiber and soil. Since, soil considers as a soft material and its mechanical properties depend on vertical stress, therefore, the Instron Tensile Tester was modified to provide fiber pull-out test through the soil matrix. Consequently, the proposed model adequately predicted shear behavior of fiber reinforced soil composite based on fiber pull-out test results.  相似文献   

8.
Natural fiber composite replaces the conventional and synthetic materials in many fields especially in light weight applications. The randomly oriented short snake grass fiber reinforced isophthallic polyester composites are prepared by hand lay-up technique and finally compression molded. The various length and weight fraction of fiber are used in composite fabrication. The mechanical properties and water absorption under various climatic conditions are examined according to the prescribed standard. SEM image revealing the fiber pullout and breakage of the tensile and impact fractured composite specimens has been analysed and compared with control through scanning electron microscope. The result shows that the mechanical properties increase with increase in fiber length and weight fraction of the composites. The rate of water absorption increases with increase in temperature and time. Obtained experimental tensile strength of the composite is compared with various theoretical models such as Series, Hirsch’s, Halpin-Tsai, Modified Halpin-Tsai and Modified Bowyer & Brader’s and the obtained inferences are discussed.  相似文献   

9.
Chemical treatment is an often-followed route to improve the physical and mechanical properties of natural fiber reinforced polymer matrix composites. In this study, the effect of chemical treatment on physical and mechanical properties of jute fiber reinforced polypropylene (PP) biocomposites with different fiber loading (5, 10, 15, and 20 wt%) were investigated. Before being manufactured jute fiber/PP composite, raw jute fiber was chemically treated with succinic anhydride for the chemical reaction with cellulose hydroxyl group of fiber and to increase adhesion and compatibility to the polymer matrix. Jute fiber/PP composites were fabricated using high voltage hot compression technique. Fourier Transform Infrared spectroscopy (FTIR) and Scanning Electron Microscopy (SEM) tests were employed to evaluate the morphological properties of composite. Succinic anhydride underwent a chemical reaction with raw jute fiber which was confirmed through FTIR results. SEM micrographs of the fractured surface area were taken to study the fiber/matrix interface adhesion and compatibility. Reduced fiber agglomeration and improved interfacial bonding was observed under SEM in the case of treated jute fiber/PP composites. The mechanical properties of jute/PP composite in terms of Tensile strength and Young’s modulus was found to be increased with fiber loading up to 15 wt% and decreased at 20 wt%. Conversely, flexural strength and flexural modulus increased with fiber loading up to 10 wt% and start decreasing at 15 wt%. The treated jute/PP composite samples had higher hardness (Rockwell) and lower water absorption value compared to that of the untreated ones.  相似文献   

10.
The tribological performance of PA6 and carbon fiber reinforced polyamide 6 (CF/PA6) under dry sliding condition was examined. Different contents of carbon fibers were employed as reinforcement. All filled and unfilled polyamide 6 composites were tested against CGr15 ball and representative testing was performed. The effects of carbon fiber content on tribological properties of the composites were investigated. The worn surface morphologies of neat PA6 and its composites were examined by scanning electron microscopy (SEM) and the wear mechanisms were discussed. Moreover, all filled polyamide 6 have superior tribological characteristics to unfilled polyamides 6. The optimum wear reduction was obtained when the content of carbon fiber is 20 vol%.  相似文献   

11.
Woven Kenaf/Kevlar Hybrid Yarn is the combination of natural and synthetic fibers in the form of thread or yarn. The yarn is weaved to form a fabric type of fiber reinforced material. Then, the fabric is fabricated with epoxy as the resin to form a hybrid composite. For composite fabrication, woven fabric Kenaf/Kevlar hybrid yarn composite was prepared with vacuum bagging hand lay-up method. Woven fabric Kenaf/Kevlar hybrid yarn composite was fabricated with total fiber content of 40 % and 60 % of Epoxy as the matrix. The fiber ratios of Kenaf/Kevlar hybrid yarn were varied in weight fraction of 30/70, 50/50 and 70/30 respectively. The composites of woven fabric Kenaf/Epoxy and woven fabric Kevlar/Epoxy were also fabricated for comparison. The mechanical properties of five (5) samples composites were tested accordingly. Result has shown that of value of strength and modulus woven fabric Kenaf/Kevlar Hybrid Yarn composite was increased when the Kevlar fiber content increased. Therefore, among the hybrid composite samples result showed the woven fabric Kenaf/Kevlar Hybrid Yarn composites with the composition of 30/70 ratio has exhibited the highest energy absorption with 148.8 J which 28 % lower than Kevlar 100 % sample. The finding indicated there is a potential combination of natural fiber with synthetic fiber that can be fabricated as the composite material for the application of high performance product.  相似文献   

12.
Lee  Wonoh  Kim  Ji Hoon  Shin  Heon-Jung  Chung  Kwansoo  Kang  Tae Jin  Youn  Jae Ryoun 《Fibers and Polymers》2003,4(2):77-83
The cell modeling homogenization method to derive the constitutive equation considering the microstructures of the fiber reinforced composites has been previously developed for composites with simple microstructures such as 2D plane composites and 3D rectangular shaped composites. Here, the method has been further extended for 3D circular braided composites, utilizing B-spline curves to properly describe the more complex geometry of 3D braided composites. For verification purposes, the method has been applied for orthotropic elastic properties of the 3D circular braided glass fiber reinforced composite, in particular for the tensile property. Prepregs of the specimen have been fabricated using the 3D braiding machine through RTM (resin transfer molding) with epoxy as a matrix. Experimentally measured uniaxial tensile properties agreed well with predicted values obtained for two volume fractions.  相似文献   

13.
Impact behaviors of the large deformable composites of Kevlar fiber reinforced composites of different preform structures have been investigated. An analytic tool was developed to characterize the impact behavior of the Kevlar composites. The image analysis technique, and deply technique were employed to develop energy balance equation under impact loading. An energy method was employed to establish the impact energy absorption mechanism of Kevlar multiaxial warp knitted composites. The total impact energy was classified into four categories including delamination energy, membrane energy, bending energy and rebounding energy under low velocity impact. Membrane and bending energy were calculated from the image analysis of the deformed shape of impacted specimen and delamination energy was calculated using the deplying technique. Also, the impact behavior of Kevlar composites under high velocity impact of full penetration of the composite specimen was studied. The energy absorption mechanisms under high velocity impact were modelled and the absorbed energy was classified into global deformation energy, shear-out energy, deformation energy and fiber breakage energy. The total energy obtained from the model corresponded reasonably well with the experimental results.  相似文献   

14.
The fiber-reinforced syntactic foam is a type of lightweight materials. In this paper, hollow glass microspheres/epoxy syntactic foams reinforced by carbon fibers are prepared. Carbon fibers of five mass fractions are used to obtain five types of reinforced syntactic foams. The effect of the fiber content and soaking corrosion on the flexural properties of syntactic foams are investigated. The results of soaking test show that the moisture rate in distilled water is greater than that in seawater. The flexural test results show that the flexural strength of syntactic foams increases obviously by adding fibers. The maximum value increases 25.5 % than that of composites without adding fibers when fiber-mass fraction is 5 %. Soaking corrosion reduces the flexural properties of the syntactic foams. The flexural strengths of syntactic foams immersed in water and seawater with 5 % fiber-mass fraction decrease 34.4 % and 37.5 % respectively. The main reasons of the flexural strength reduction of syntactic foams with soaking corrosion are discussed.  相似文献   

15.
Mechanical properties of chopped carbon fiber (CF) reinforced PC/ABS composites were investigated. Tensile strength and elastic modulus of the composites were enhanced with increasing CF contents. On the contrary, impact strength of the composite was decreased with increasing CF fraction. Film insert molding was introduced in order to improve impact strength. Film insert molded composite specimens have higher impact strength than conventional injection molded composite specimens because inserted film acted as a cushion to absorb the impact energy. Large warpage which was observed after molding and known as a disadvantage of the film insert molded part can be prevented by controlling the amount of filled CFs. Therefore, fiber reinforcement and film insert molding can be applied simultaneously to reduce warpage of the film insert molded part and enhance impact strength of the CF reinforced composite.  相似文献   

16.
This study was performed to investigate the influence of heat treatment on the chemical transformation and associated improved durability of short bamboo-fibers (BF) and its reinforced composites. Results showed that cleavage of acetyl groups of the hemicelluloses developed with increasing temperature and holding time, and completed beyond 190 °C for more than 3 h, resulting in a noticeable increase of cellulose content and a substantial reduction of concentration of accessible hydroxyl groups. Heat treatment improved thermal stability and anti-UV aging properties of treated BF, and also contributed to a decrease of equilibrium moisture content (EMC) of treated BF and consequent improvements of hygroscopicity and the dimensional stability of its reinforced composite. However, immoderate heat treatment for BF wasn’t in favor of improvements of hygroscopicity and the dimensional stability of BF based composites.  相似文献   

17.
In the present paper, ramie fiber reinforced polymer (RFRP) plates prepared by hot compression process were subjected to water immersion at 20 oC and 40 oC for four weeks, and the variation of water uptake and mechanical properties with immersion time were investigated. It was found that the saturated water content and the coefficient of diffusion in RFRP were much higher than those in synthetic fiber based composites, due to the strong hydrophilic characteristic of the ramie fiber. After fully drying of the immersed samples, mass loss from 1.6 % to 3.6 % was found, indicating occurrence of a serious hydrolysis of the resin and the ramie fibers. After a short term of immersion (i.e., 1 day), RFRP showed a remarkable deterioration in the flexural and short beam shear properties. Further increase of the immersion time, the degradation rate of the mechanical properties was much reduced. After fully drying, the mechanical properties of the samples can be recovered to some extent, but still much less than the original values. The variation of mechanical property as a function of the water uptake content exhibits three stages (i.e., dramatic reduction, leveling off and quick decrease again). This may be due to the sequent occurrence of the degradation of natural fibers, fiber debonding and hydrolysis of the fiber and resin during immersion.  相似文献   

18.
The chemical and morphological properties of ramie fibers treated by chemical surface modification were examined with Fourier transform infrared (FT-IR) spectroscopy. The mechanical and thermal decomposition properties were evaluated with respect to tensile strength, tensile modulus and thermogravimetric analysis (TGA). Surface morphological changes were investigated with scanning electron microscopy (SEM). Finally, the capabilities of composites reinforced with various chemically treated fibers were analyzed by investigating tensile and impact strengths. Additionally, the thermal mechanical properties of the composites were investigated with thermal mechanical analysis (TMA). Based on the results of these analyses, we concluded that pectin, lignin and hemicellulose were removed and thermal stability was increased with chemical treatments. The composites reinforced with ramie fiber showed better properties compared with pure PLA matrix with respect to tensile and impact strengths. The peroxide-treated fiber composite had the smallest thermal expansion.  相似文献   

19.
Bio-materials have ignited a quest among research fraternity to be used in every possible field of applications like automobile, sports, medical, civil and textile industry. Application spectrum of natural fiber reinforced polymer composites is spreading globally in every field of engineering having structural and tribological applications. The present work investigates the tribological performance of regionally available inexpensive plant based natural fiber reinforced polymer composites. In this work, three different types of natural fibers (jute, hemp, and flax) were reinforced with epoxy matrix to fabricate natural fiber reinforced polymer composites (NFRP) and their hybrid composites (jute/hemp/Epoxy, hemp/flax/epoxy and jute/ hemp/flax/epoxy) using hand-layup technique. Tribological performance of the developed bio-composites were evaluated in terms of frictional characteristics and sliding wear under dry contact condition at different process parameters, such as applied load (10-50 N), sliding speed (1-5 m/s) and sliding distance (1000-2000 m). Experimental results of wear analysis confirmed that incorporation of natural fibers into epoxy polymer matrix significantly improved the wear behavior of the developed NFRP composites in comparison to neat epoxy polymer. Among all the developed composites, jute/epoxy composite achieved the highest coefficient of friction, frictional force and specific wear rate. Dynamic mechanical analysis (DMA) was also analyzed to evaluate the viscoelastic behavior of the developed composites. The surface morphology of samples after wear test was examined by scanning electron microscopy to investigate and propose the possible wear mechanism of the developed composites.  相似文献   

20.
In this study, physical, mechanical, and flammability properties of coconut fiber reinforced polypropylene (PP) composite panels were evaluated. Four levels of the coir fiber content (40, 50, 60, and 70 % based on the composition by weight) were mixed with the PP powder and a coupling agent, 3 wt % maleic anhydride grafted PP (MAPP) powder. The water resistance and the internal bond strength of the composites were negatively influenced by increasing coir fiber content. However, the flexural strength, the tensile strength, and the hardness of the composites improved with increasing the coir fiber content up to 60 wt %. The flame retardancy of the composites improved with increasing coir fiber content. The results suggest that an optimal composite panel formulation for automotive interior applications is a mixture of 60 wt % coir fiber, 37 wt % PP powder, and 3 wt % MAPP.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号