首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 62 毫秒
1.
杉木积成材薄木贴面工艺初探   总被引:4,自引:0,他引:4  
杜春贵  林秀珍  施友云 《林业科技》2004,29(1):43-44,62
采用正交试验法,探讨了杉木积成材薄木贴面的工艺过程。试验结果表明:利用杉木积成材进行薄木贴面.工艺切实可行,奥古曼薄木贴面的较佳工艺参数为:热压温度100℃,热压压力1.0MPa,热压时间4min,涂胶量120g/m^2。  相似文献   

2.
PF与UF树脂混合比对竹帘板胶合性能的影响   总被引:2,自引:0,他引:2  
以酚醛(PF)胶为基础,通过与不同加量的脲醛(UF)胶相混合,形成一系列混合胶粘剂。在不同的热压条件下,用混合胶粘剂压制竹帘胶合板,经对各组分制品的耐沸水和耐老化性检验,确认当热压温度为140℃时,脲醛胶的最大加量可以达到酚醛胶量的40%,制品的胶合状态不会受到破坏。  相似文献   

3.
采用正交试验法探讨了各热压工艺因子对稻草刨花板薄木贴面的影响.试验结果表明:稻草刨花板表面饰贴薄木是切实可行的,进行0.2 mm厚水曲柳薄木贴面,在选用PVAC胶黏剂且涂胶量为100 g/m2的条件下,其较佳工艺参数分别为:热压压力为0.7 MPa、热压温度为100℃、热压时间为120 s;在选用GB-3胶黏剂且涂胶量为100 g/m2的条件下,其较佳工艺参数分别为:热压压力为0.8 MPa、热压温度为90℃、热压时间为180 s.进行0.6mm厚白橡薄木贴面,在选用PVAC胶黏剂且涂胶量为120g/m2的条件下,其较佳工艺参数分别为:热压压力0.8MPa、热压温度90℃、热压时间240 s;在选用GB-3胶黏剂且涂胶量为120g/m2的条件下,其较佳工艺参数分别为:热压压力0.7 MPa、热压温度90℃、热压时间180 s.  相似文献   

4.
水曲柳薄木厚度与胶粘剂的关系   总被引:2,自引:0,他引:2  
水曲柳薄木厚度与胶粘剂的关系刘光宇,杨国卿(黑龙江东京城林业局人造板厂东京城157421)薄木贴面,是将纹理美观大方的天然木质薄木胶贴在人造板板面上的一种饰面方法。人造板经薄木贴面后,表面变得木纹逼真新颖,色泽自然清晰,具有天然木质感,而且强度明显增...  相似文献   

5.
1胶粘剂选择及热压工艺目前,人造板厂家生产贴面板时,常用的胶合剂有脲醛树脂胶(UF)、三聚氰胺-甲醛胶(MF)、聚醋酸乙烯酯乳胶(PVAC)和氯丁橡胶(CR)。应用最广泛的是脲醛树脂胶,其可以热压贴面,也可以冷压贴面。而聚醋酸乙烯酯乳胶和氯丁橡胶胶粘剂,则主要用于冷压贴面工艺。冷压贴面胶合效果较好,温度低,含水率变化较小,贴面变形也小。缺点是冷压时间长,为了提高劳动生产率,可数十张贴面板叠起来一次加压完成。冷压贴面常用的胶种为聚醋酸乙烯酯乳胶,还有用氯丁胶和硅酮密封胶的。其特点是使用方便,贮存期长,但其价格较高,耐水性差,耐…  相似文献   

6.
封闭异氰酸酯改性脲醛树脂制备胶合板   总被引:2,自引:0,他引:2  
采用亚硫酸氢钠封闭异氰酸酯改性UF树脂制备胶合板,研究了制板用混合胶液的比例、热压时间、热压温度等热压工艺对胶合板性能的影响,结果表明,在UF/PAPI=100/10、热压温度为110℃、热压时间为4min时,所制备胶合板的甲醛释放量达到国家标准,并且具有较高的胶合性能.  相似文献   

7.
以紫檀薄木、刨花板为研究材料,对薄木湿法贴面中装饰效果的主要影响因素,如薄木的含水率、涂胶量、热压的温度和时间等方面进行研究,以期为薄木湿法贴面的工业生产提供改进的理论依据。研究表明:在含水率为30%、热压温度为90℃、热压时间为2min、涂胶量为88.9g/m2时,对紫檀薄木进行湿法贴面能得到较好的表面装饰效果。  相似文献   

8.
热压法制备速生杉木集成材工艺   总被引:1,自引:0,他引:1  
采用脲醛树脂胶粘剂,运用热压胶合工艺,对速生杉木进行指接与侧拼胶合后制成集成材,并进行横向静曲强度和弹性模量测试:分析热压法制备速生杉木集成材的工艺可行性,讨论侧拼压力、胶合时间与热压温度对速生杉木集成材横向静曲强度与弹性模量的影响,为速生杉木集成材的热压法生产提供理论依据。试验结果表明,在本研究试验条件内,采用脲醛树脂作为胶粘剂,运用热压法制备速生杉木集成材是可行的。  相似文献   

9.
为了丰富竹地板的外观效果,扩大竹地板的种类,采用正交试验方法,探讨了竹地板表面进行0.6 mm榉木和2.0 mm枫木薄木贴面工艺。结果表明:利用榉木和枫木薄木贴面竹地板切实可行,其较佳工艺参数分别为:榉木热压压力0.8 MPa,热压温度100℃,热压时间240 s,涂胶量为120 g/m2;枫木热压压力1.2 MPa,热压温度120℃,热压时间360 s,涂胶量140 g/m2。  相似文献   

10.
以板式家具用薄木贴面刨花板为研究对象,研究水曲柳薄木贴面的工艺条件:施胶配比、涂胶量、热压温度对薄木贴面刨花板挥发性有机化合物(VOCs)释放特性的影响。结果表明,薄木贴面能减少刨花板VOCs的释放,热压温度升高、施胶量增大都会使薄木刨花板的总有机挥发物(TVOC)释放量增大,初始释放浓度上升,施胶配比增加,TVOC释放量呈现先减小后增大的趋势;通过对试件VOCs成分进行分析表明,施胶量越高,萜和脂肪族类物质含量越低,饱和烃类和苯系物化合物挥发量越高;热压温度越高,苯系物化合物相对含量越大,而饱和烃类物质和萜类物质的相对含量越小。  相似文献   

11.

In Scandinavia, moose (Alces alces L.) sometimes cause severe browsing damage to economically-important pine. Moose-vehicle accidents have spurred construction of fences along roads, and these may interfere with moose migration between summer and winter ranges, or the road alone may be a barrier. If this happens and moose build up along roads, landowners may suffer economically. Therefore, this study investigated whether roads, fences or other factors influence the use of young pine stands by moose. Eighty stands along roads in northern Sweden were evaluated in which individually-browsed branches were counted on 9972 pines. Moose browsing was not significantly related to birch (Betula pendula Roth, B. pubescens Ehrh.) density, nor did it differ between pines (Pinus contorta Douglas or P. sylvestris L.). However, increased pine density, site productivity and proximity to a highway were associated with increased browsing. Further large-scale studies are needed to understand moose habitat selection and the effects of roads.  相似文献   

12.

The root systems of 2-yr-old Picea glauca, Picea mariana and Pinus banksiana seedlings were submitted to various frost temperatures during an artificial frost to induce different levels of root damage. Frost-damaged and control seedlings were placed in a greenhouse under high and low soil moisture regimes. Seedling growth and physiology were evaluated periodically. Seedling survival was reduced when root damage reached levels of 60-80%. Root systems of all three species showed partial to total recovery by the end of the experiment. In general, root freezing damage caused reductions in seedling growth, with these reductions becoming less significant over time. Root damage had little to no effect on black spruce and jack pine seedling physiology, while white spruce CO 2 uptake decreased with increasing root damage. Shoot nitrogen content of all three species decreased slightly with increasing root damage.  相似文献   

13.
Contour hedgerows of multipurpose tree species in the sloping tea lands of Sri Lanka are expected to reduce soil erosion and also add significant amounts of plant nutrients to the soil via periodic prunings. The objective of this experiment was to characterize the biomass decomposition pattern and quantify the amount of nutrients added through prunings of six tree species (Calliandra calothyrsus, Senna spectabilis, Euphatorium innulifolium, Flemingia congesta, Gliricidia sepium and Tithonia diversifolia) currently being used in hedgerows associated with tea. Withered leaf and stem prunings (50 g) were enclosed in 2-mm litter bags, placed at 5-cm depth and retrieved after one, three, six, nine and 12 weeks. Loss of initial dry weight, N, P and K was measured. Single exponential decay function adequately described both dry weight and nutrient loss. Tree species differed significantly in their rate of breakdown with decomposition constants (k) varying from 0.0299 to 0.2006 week−1 for leaves and from 0.0225 to 0.0633 week−1 for stems. Gliricidia showed the highest k for leaves with the rest in the following descending order: Senna > TithoniaEuphatorium > Calliandra > Flemingia. A similar pattern was observed for loss of all nutrients with Calliandra and Flemingia always having lower k values than the rest. Although N immobilization was not observed, immobilization of P and K was observed during the first week of incubation in some species, particularly in stem prunings. Annual biomass of prunings differed significantly between tree species in the following descending order: Calliandra > Senna > Flemingia > Tithonia > Gliricidia > Euphatorium. Calliandra added the greatest amount of nutrients annually to the soil with Euphatorium adding the least. Calliandra prunings provided the annual total K requirement and 49% of the N requirement of mature tea. However, none of the species provided more than 5% of the P requirement. It is concluded that among the tree species tested, Calliandra and Flemingia are the most suitable for contour hedgerows in tea plantations of this agroclimatic region because of their higher soil nutrient enrichment capacity and slower decomposition rates which would minimize leaching losses. This revised version was published online in June 2006 with corrections to the Cover Date.  相似文献   

14.

This study investigated the stand structure in pine, spruce and deciduous forests in the border district of Finland and Russia. A total of 46 mature forest stands was selected as pairs, the members of each pair being as similar as possible with respect to their forest site type, age, moisture and topography. The stands were then compared between the two countries by means of basal areas and number of stems. The proportions of dominating tree species were 2-12% lower, and correspondingly the proportions of secondary tree species higher, in Russian forests. The density of the forest stock was also higher in each forest type in Russia. The forests in the two countries differed most radically in terms of the abundance of dead trees. The amount was two to four times higher in Russian deciduous and spruce forests, and in pine forests the difference was 10-fold. The stand structures indicated that Russian coniferous stands, in particular, were more heterogeneous than intensively managed pine and spruce stands in Finland.  相似文献   

15.

The root collar diameter and the height:diameter ratio are of particular importance in container-grown seedlings where a high density in the containers may produce spindly seedlings. Temperature regimes and light quality are known to affect plant growth. The aim of this study was to identify responses in Picea abies (L.) Karst. seedlings grown with light providing different red:far-red ratios and under temperature regimes with alternating day (DT) and night temperature (NT) from negative (DT < NT) to positive (DT > NT) difference (DIF) between DT and NT. Experiments were conducted in controlled environment chambers and in a daylight phytotron. Only limited thermoperiodic responses appeared in P . abies seedlings with respect to seedling height and dry weight accumulation. The formation of terminal buds, however, was clearly delayed in seedlings grown at negative DIF. The results indicate a requirement for day extension light that is high in far-red, to prevent terminal bud formation under natural short-day conditions. An extended study should be conducted to clarify the minimum level of light intensity and the optimal light quality needed to prevent terminal bud formation under natural short-day conditions.  相似文献   

16.
Heterobasidion parviporum and Heterobasidion annosum are widely distributed root‐rot fungi that infect conifers throughout Europe. Infection of conifer stumps by spores of these pathogens can be controlled by treating fresh stumps with a competing non‐pathogenic fungus, Phlebiopsis gigantea. In this study, growth of three Latvian strains of P. gigantea and the biological control agent ‘Rotstop’ strain was evaluated in stem pieces of Norway spruce, Scots pine, lodgepole pine, Douglas‐fir, Weymouth pine, Siberian larch and Sitka spruce. The growth rates of one H. parviporum and one H. annosum isolate were also measured in the same stem pieces. The growth rate of P. gigantea varied greatly in wood of different conifer species. It was higher in the three pine species, lower in Norway spruce and lowest in Sitka spruce and Siberian larch, and in Douglas‐fir, this fungus did not grow. The largest area of wood occupied by P. gigantea was in lodgepole pine. Growth of Latvian isolates of P. gigantea in the wood of Pinus and Picea species was comparable to that of the Rotstop isolate. Consequently, stump treatment with local P. gigantea isolates should be recommended. However, our results suggest that Douglas‐fir stump treatment against Heterobasidion by P. gigantea may be ineffective and other stump treatment methods should be considered.  相似文献   

17.

The effects of seed weight and seed type on seedling growth of Pinus sylvestris (L.) were studied by seeding individually weighed orchard and stand seed in different mixtures under harsh (direct seeding in field) and optimal (seeding in nursery) conditions. In the nursery experiment an increase in the seed weight from 3 to 7 mg increased the seedling height by 10-27% and total weight by 27-113%, and decreased the height/diameter ratio by 5-6% after 2 yrs. With elimination of seed weight effects, orchard seedlings were 2% taller than stand seedlings in year 2. Without elimination of seed weight effects, orchard seedlings were 7-13% taller. In the field experiment an increase in the seed weight from 3 to 7 mg increased seedling height by 18-65%, stem volume by 81-274% and the number of top-buds by 23-34% in year 5. After elimination of seed weight effects, orchard seedlings were 7-13% taller than stand seedlings and without elimination of seed weight effects 20-21% taller after 5 yrs. Even after elimination of both seed weight and genetic effects orchard seedlings were 3-9% larger than stand seedlings in the field experiment. In conclusion, the influence of seed weight and seed type on growth traits and slenderness is highly significant and the influence seems to be greater in harsh conditions.  相似文献   

18.
本文分析了CAD在设计中引起的正面和负面影响,并进行了系统的阐述,从而使设计者在应用中能够保持客观的态度。  相似文献   

19.
Baobab leaves form an important part of the local diet in Sahel countries and elsewhere in Africa. Existing leaf nutritional data and agroforestry performance information are based solely on Adansonia digitata L., the baobab of continental Africa. The introduction potential of Adansonia species from the center of diversity in Madagascar and from Australia remains untapped. To assess this potential, the mineral contents and B1 and B2 vitamin levels of dried baobab leaves were determined for five-year old trees of A. digitata, A. gibbosa (A. Cunn.) Guymer ex D. Baum, A. rubrostipa Jum. & H. Perrier (syn. A. fony Baill.), A. perrieri Capuron and A. za Baill. grown in an introduction trial in Mali. Nutritional data were evaluated against survival and vigor to identify promising germplasm. Leaf vitamin and crude protein contents were highest in the Madagascar species, especially A. rubrostipa (B1 88 mg 100 g−1, B2 187 mg 100 g−1, protein 20.7% dry weight). However, the local species far outperformed the introductions in survival, tree height, basal diameter and resistance to termites. We suggest grafting as a way of harnessing the vigor of well-adapted local baobab varieties to the superior nutritional profiles of A. rubrostipa and others. Cross-species grafting tests in Adansonia were successful, thus creating new agroforestry possibilities with different scion/rootstock combinations.  相似文献   

20.
Abstract

Wood in general and wooden studs in particular are often distorted owing to uneven shrinkage during the drying process in the sawmill. Twist is often the most detrimental of all types of distortion, and it is caused by spiral grain in combination with variations in moisture content. For sawmills, the objective is to produce dried, straight boards, and one method of dealing with boards with excessive spiral grain is to sort them out and then dry them in a pretwisted position to obtain straight boards after drying. A model using the finite element (FE) method for the simulation of drying twist distortions was first calibrated against laboratory experiments in which boards were dried with and without restraints and pretwists. After the calibration, the FE results were compared with industrial test results for boards that were dried without restraints or with restraints with zero pretwist, i.e. straight restraints. The FE model used an elastic–ideally plastic material model to obtain permanent deformations. The calibration was to set the yield stresses so that there was a good match between FE results and results from the laboratory experiments. The comparison between the industrial test results and the FE results showed that the FE model is capable of realistic simulations of drying boards with and without restraints and presumably also pretwists.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号