共查询到19条相似文献,搜索用时 828 毫秒
1.
本文根据苏州林机厂对 B B113型纵向刨切机几次试生产的实际情况,从木方和刨切机的机械精度二方面对影响刨切薄木精度的诸因素作了浅析。 相似文献
2.
3.
为解决传统热磨法加工微米薄木片及木纤维中高能耗、工序复杂、加工成本高的缺点,现改变加工方法,采用顺纹纵向刨切木材的方式,研发了数控微米刨切试验台。试验台主要由机架、纵向进给机构总成、工件夹具、控制面板、刨切机构总成、升降机构总成和限位机构组成,可对宽度为50 mm,长度为300~600 mm,高度为20~90 mm的木材工件进行纵向进给、切削量进给和刨切作业。笔者对试验台整机以及各机构进行设计,并通过ANSYSY对刀具进行强度校核。通过试验,确定刨切机构切削角δ取45°,刀刃伸出量h取0.05 mm,刀门宽度d取0.2 mm,刨得的木片平均厚度为18.7μm,最薄为15μm。最后通过显微镜观察发现经过刨切后的刀刃部分出现磨损,可通过表面改性提高刀具的耐磨性。 相似文献
4.
南方阔叶材刨切薄木生产工艺 总被引:1,自引:0,他引:1
随着我国家具和人造板工业的发展 ,人造板表面装饰技术发展迅速 ,特别是薄木贴面装饰技术 ,它既能大量节省珍贵木材 ,又能为人们提供高档的装饰效果 ,是一种国内外广泛采用的装饰方法。一般薄木生产设备包括薄木制取设备和薄木干燥设备 ,生产薄木的方法有旋切法、半圆旋切法和刨切法。根据刨切方向和木方长度方向垂直还是平行 ,又可将刨切法分为横向刨切机和纵向刨切机。本文就酸枣、枫香、檫树等南方主要优质阔叶材纵向刨切生产薄木的工艺进行介绍。1 锯制木方家具贴面薄木一般有径切木纹和弦切木纹两种。刨切薄木的木材纹理随木方锯制方… 相似文献
5.
6.
《林业机械与木工设备》1997,(11)
专利简介卫生木筷倒圆角刨床这种刨床是在刨体的上下两侧分别设置有一对短刨头和一对长刨头,短刨头和长刨头均可绕轴转动,在短刨头和长刨头的前后两端分别安装有可调式刨口及切削刀刃,它可生产出不同形状棱角和无毛刺的木筷,不需要经常更换刀具,延长了刨床的使用寿命... 相似文献
7.
采用南方常见树种马尾松、木荷、枫香、酸枣等进行纵向刨切人造薄木的试制,对工艺参数作了探索,并对胶合条件(胶粘剂种类、基材)及其对胶合强度的影响进行了较详细的研究。 相似文献
8.
根据辽西地区的自然条件和人工刺槐林生长情况,通过采用留伐根,刨伐根,刨伐根并犁沟三种萌芽更新方法试验,分析了不同更新方法更新后萌生株数和生长情况,提出了刨伐根和刨伐根并犁沟两种较为理想的更新方法和适用范围,人工刺槐林萌芽更新采用刨伐根和刨伐根并犁沟方法更新后不仅萌生株数多,而且分布均匀,更新效果好。 相似文献
9.
实木压缩弯曲技术是丹麦20世纪90年代推出的最新技术,它是把锯好或刨好的木材放进蒸气罐内进行喷蒸加热,使其软化,然后用液压机顺着木材纤维方向进行纵向压缩,几分钟后就可以轻而易举地对其进行弯曲变形,然后进行干燥处理,使其弯曲后的形状保持不变。该技术与传 相似文献
10.
研究了纵向刨切单板时切削厚度、刀刃倾角对单板背面裂隙度和粗糙度以及声发射振铃计数的影响.结果表明,随着刨切厚度的增加,单板背面裂隙度和粗糙度以及声发射振铃计数都明显增加;随着刀刃倾角的增加(45°~70°),单板背面裂隙度和粗糙度小幅增加,但声发射振铃计数明显增加;声发射振铃计数与单板背面裂隙度和粗糙度均具有良好的线性关系. 相似文献
11.
徒手切片法在进口材木材识别中的应用 总被引:2,自引:1,他引:2
从工具的制作、材料的处理、操作方法等方面介绍了采用徒手切片识别进口材的方法,并阐明其在高度木质化的木材中的应用与常规切片方法相比存在的优点、不足及注意事项,该方法适宜在时效性要求较高及珍贵或高档木制品的木材鉴定中应用. 相似文献
12.
Summary This paper investigates a method for slicing thick pieces of wood across the grain using a sharp steel knife, and it demonstrates the effectiveness of the knife slicing process at an experimental level. In order to highlight the key parameters facilitating or hindering the thick slicing process, several factors affecting the cutting forces and the cut surface quality have been studied; the blade geometry, the effect of friction, the cutting speed, the boundary load constraints and the wood moisture content. The results indicate that a large proportion of the cutting force may be related to the wedging action of the blade in the wood. Therefore, significant reductions in the cutting energy can be achieved by optimising the blade shape. A simple homogeneous strain model has been developed which quantifies the cutting forces in terms of the blade angle and the blade surface friction. The results from this theoretical model are compared with the experimental findings and discussed in relation to methods for improving the cutting technique.This work was funded by the Foundation for Research Science and Technology. This support is gratefully acknowledged 相似文献
13.
14.
15.
白杨刨片横纹压缩流变性能 总被引:4,自引:3,他引:4
用参数分离法对手工刨切的厚为0.8、0.5、0.35、0.25、0.15mm的白杨刨片进行了横纹压缩流变试验。结果表明,用上述几种厚度的刨片所分别叠成的厚约10mm的试件,其柔量大于厚度为10mm木块试件的柔量;刨片越薄,柔量越大。弹性变形及瞬间塑性变形的增长,意味着实木经过刨切,因反复受力而使木材高聚物分子及细胞壁组织都受到影响,并有一定程度的破坏。实木经过刨切成为薄片后再层叠起来所组成的试样,在横纹压缩流变性能方面所体现的变化,一定程度上与木块受压所发生的变化,在趋势上是一致的。然而,由于前者试样系由薄刨片层叠而成,因而在影响其流变性能的诸多因素中,尚有刨片厚度及刨片层叠方向二者明显的影响作用。 相似文献
16.
We measured the longitudinal and tangential shrinking processes in wood specimens from Chamaecyparis obtuse Endl. with different microfibril angles (MFAs). The shape of the shrinking curve was compared with the MFA. Only the longitudinal
shrinking process of specimens with a small MFA clearly showed nonlinearity, and the degree of nonlinearity increased as the
MFA decreased. In contrast, the tangential shrinking process and the longitudinal shrinking process of compression wood with
a large MFA were linear. The nonlinearity is probably caused by the longitudinal shrinkage of the noncrystalline region of
the cellulose microfibril (CMF) in regions of low moisture content during water desorption. When the moisture content is high,
the matrix substance in the cell wall begins to dry; however, the shrinkage in the chain direction is restrained by the rigid
CMF. As the wood dries further, the noncrystalline region of the CMF embedded in the matrix substance begins to shrink. Because
the longitudinal mechanical behavior of wood with a small MFA is greatly affected by a rigid CMF, longitudinal shrinkage increases
suddenly at about 10% moisture content; as a result, the shrinking process shows nonlinearity. 相似文献
17.
18.
随着技术的不断创新,利用普通木材甚至低质速生材生产各种仿天然珍贵木材颜色和纹理的科技木得到越来越广泛的应用。但是,科技木锯材出材率低是目前国内科技木生产厂家所面临的突出问题,严重制约行业发展。采用3种研究方案,即两端头锯截表面刨切后再胶合模压(A)、两端头中间夹多层单板后再胶合模压(B)和两端头直接胶合模压(C),对科技木一次锯材得到的三角形截锯端头进行再利用,以提高科技木锯材出材率。结果表明,依照3种方案制备的试样其MOR、MOE、浸渍剥离性能均高于LYT 1655—2006重组装饰材要求,同时将科技木锯材出材率提高17%左右。综合考虑试样的力学性能、出材率及经济性,A方案和C方案优于B方案。通过表面粗糙度和接触角实验,对上述结果进行了验证。 相似文献