首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 62 毫秒
1.
通过对国内外木质工字梁的研究现状进行归纳和分析,总结了木质工字梁的设计规范及材料、连接方式、截面尺寸、腹板开孔和环境对梁物理力学性能、应用性能及耐久性能(蠕变)的影响。同时阐述了竹质工字梁的设计与制造技术,物理力学性能检测与评估等方面的研究进展。  相似文献   

2.
预组型木质工字梁静态力学性能设计思路的探讨   总被引:2,自引:1,他引:1  
以钢质工字梁的设计理论和木质材料学与工艺为依据,对预组型木质工字梁(IJ)的部件——翼缘、腹板,以及两者之间的连接木质工字梁整体进行受力分析,并结合材料的蠕变等影响木质IJ静态力学性能的因素以及木结构建筑对木质IJ的要求,提出了IJ的基本设计思路。  相似文献   

3.
本文对预组型木质工字梁的结构性能进行分析研究。通过对梁接口承压能力的测试结果表明:IB翼缘/腹板接口的端头承压破坏可分为先期破坏(对应的是无效胶合或胶合不良)和终极破坏(对应的是有效胶合)二种主要形式,先期破坏主要是翼缘/腹板胶合层的剪切破坏或工字梁槽底木材的横纹拉伸破坏,终极破坏的形式是工字梁胶合层剪切、翼缘槽底木材横纹拉伸和压缩的综合性全面破坏。由于终极破坏荷载是工字梁接口的最大垂向抗压破坏荷载,因此要求木结构工字梁接口几何尺寸的设计应努力避免垂向受压时不发生先期破坏。  相似文献   

4.
阐述了木质工字搁栅的特点,介绍了利用胶合板生产设备加工制造工字搁栅用落叶松单板类足尺翼缘和腹板基材的工艺技术.对腹板和翼缘物理力学性能的研究结果表明:落叶松单板类足尺翼缘和腹板的主要性能可以达到美国APA相关标准的要求.  相似文献   

5.
为研究水分对木质工字梁(IB)翼缘/腹板接口力学性能及尺寸稳定性的影响,通过单因素试验,检测不同含水率下IB翼缘/腹板接口的垂向承载能力、胶合性能、以及抗劈裂性能。结果表明,IB的综合性纤维饱和点只有25%左右;含水率从8.9%提高到25%的接口的承压能力下降了47.2%,含水率从25%提高到53%的接口的承压能力仅下降了0.6%;水分对IB翼缘和腹板尺寸变化的影响是水分影响接口承载能力的间接因素;吸湿后接口的承载能力并不能恢复到吸湿前的初始水平;解吸至8.9%含水率的IB接口的承载能力比吸湿前同等含水率的IB接口低了17.8%。  相似文献   

6.
测试木质工字梁翼缘/腹板接口胶合层拉伸性能,并对接口胶合层拉伸破坏形式及影响胶合性能的因素进行分析研究,结果表明:IB接口可以形成胶合层附近木材率先破坏的有效胶合(其木破率一般大于60%),也可发生胶合层率先破坏的无木破率的无效胶合;由于有效胶合接口的承载能力显著高于无效胶合接口,因此要求接口发生的必须是有效胶合。偏大的接口角度β和接口槽深i有利于接口有效胶合的形成和胶合性能的提高。  相似文献   

7.
采用双因素试验法,设3°、6°和9°为接口角变化水平,设9、12 mm和15 mm为接口槽深变化水平,对预组型木质工字梁翼缘/腹板接口的抗劈裂性能进行研究。研究表明:IB翼缘/腹板接口角度的大小和接口槽深的深浅对IB翼缘/腹板接口的胶合性能和承载能力产生利弊性影响。翼缘/腹板接口角度越大则接口翼缘的抗劈裂性能越好,但越深则接口翼缘的抗劈裂性能越差;从IB翼缘/腹板接口抗劈裂性能的角度看,接口角度以9°为宜,槽深以9 mm为宜。  相似文献   

8.
李军伟  云建辉 《林业科技》2019,(2):31-33,42
对木结构工字梁结构进行优化设计,并对木结构工字梁的规格尺寸及主要技术指标进行测试。研究结果表明:经优化设计后,木结构工字梁具有卓越的物理力学性能,能够满足使用相关性能的要求;木结构工字梁作为替代实木梁的木建筑构件,具有其突出的自身优势,木结构工字梁比实木梁具有更高的强度、刚度、尺寸稳定性,具有更大的跨度能力以及更小发生几率的翘曲、扭曲和劈裂,有更低的伸缩率。  相似文献   

9.
基于静态弯曲性能的木质工字梁设计计算方法探讨   总被引:1,自引:0,他引:1  
参照钢质工字梁静态弯曲理论,对木质工字梁(IJ)的“荷载一位移”曲线、IJ正应力理论计算值与实测值、IJ整梁挠度理论计算值与实测值的对比分析,结果认定:1)钢质工字粱的静态弯曲理论计算公式,可用于IJ弹性段应力和挠度的分析计算;2)IJ整梁静态弯曲性能的分析计算时,应注意IJ上翼缘压缩特性和下翼缘拉伸特性的差异。  相似文献   

10.
木质材料在包装、建筑、家具、铁路等领域正发挥着巨大的作用,而木质材料力学性能的检测则是这类材料使用过程中的重要依据。介绍了木质材料力学性能无损检测的主要方法和原理;阐述了几种主要的检测技术(如机械应力法、振动检测法、应力波检测、超声波检测等)的研究现状及存在的问题;并在此基础上,提出木质材料力学性能检测技术的发展趋势。  相似文献   

11.

In Scandinavia, moose (Alces alces L.) sometimes cause severe browsing damage to economically-important pine. Moose-vehicle accidents have spurred construction of fences along roads, and these may interfere with moose migration between summer and winter ranges, or the road alone may be a barrier. If this happens and moose build up along roads, landowners may suffer economically. Therefore, this study investigated whether roads, fences or other factors influence the use of young pine stands by moose. Eighty stands along roads in northern Sweden were evaluated in which individually-browsed branches were counted on 9972 pines. Moose browsing was not significantly related to birch (Betula pendula Roth, B. pubescens Ehrh.) density, nor did it differ between pines (Pinus contorta Douglas or P. sylvestris L.). However, increased pine density, site productivity and proximity to a highway were associated with increased browsing. Further large-scale studies are needed to understand moose habitat selection and the effects of roads.  相似文献   

12.

The root systems of 2-yr-old Picea glauca, Picea mariana and Pinus banksiana seedlings were submitted to various frost temperatures during an artificial frost to induce different levels of root damage. Frost-damaged and control seedlings were placed in a greenhouse under high and low soil moisture regimes. Seedling growth and physiology were evaluated periodically. Seedling survival was reduced when root damage reached levels of 60-80%. Root systems of all three species showed partial to total recovery by the end of the experiment. In general, root freezing damage caused reductions in seedling growth, with these reductions becoming less significant over time. Root damage had little to no effect on black spruce and jack pine seedling physiology, while white spruce CO 2 uptake decreased with increasing root damage. Shoot nitrogen content of all three species decreased slightly with increasing root damage.  相似文献   

13.
Contour hedgerows of multipurpose tree species in the sloping tea lands of Sri Lanka are expected to reduce soil erosion and also add significant amounts of plant nutrients to the soil via periodic prunings. The objective of this experiment was to characterize the biomass decomposition pattern and quantify the amount of nutrients added through prunings of six tree species (Calliandra calothyrsus, Senna spectabilis, Euphatorium innulifolium, Flemingia congesta, Gliricidia sepium and Tithonia diversifolia) currently being used in hedgerows associated with tea. Withered leaf and stem prunings (50 g) were enclosed in 2-mm litter bags, placed at 5-cm depth and retrieved after one, three, six, nine and 12 weeks. Loss of initial dry weight, N, P and K was measured. Single exponential decay function adequately described both dry weight and nutrient loss. Tree species differed significantly in their rate of breakdown with decomposition constants (k) varying from 0.0299 to 0.2006 week−1 for leaves and from 0.0225 to 0.0633 week−1 for stems. Gliricidia showed the highest k for leaves with the rest in the following descending order: Senna > TithoniaEuphatorium > Calliandra > Flemingia. A similar pattern was observed for loss of all nutrients with Calliandra and Flemingia always having lower k values than the rest. Although N immobilization was not observed, immobilization of P and K was observed during the first week of incubation in some species, particularly in stem prunings. Annual biomass of prunings differed significantly between tree species in the following descending order: Calliandra > Senna > Flemingia > Tithonia > Gliricidia > Euphatorium. Calliandra added the greatest amount of nutrients annually to the soil with Euphatorium adding the least. Calliandra prunings provided the annual total K requirement and 49% of the N requirement of mature tea. However, none of the species provided more than 5% of the P requirement. It is concluded that among the tree species tested, Calliandra and Flemingia are the most suitable for contour hedgerows in tea plantations of this agroclimatic region because of their higher soil nutrient enrichment capacity and slower decomposition rates which would minimize leaching losses. This revised version was published online in June 2006 with corrections to the Cover Date.  相似文献   

14.

The effects of seed weight and seed type on seedling growth of Pinus sylvestris (L.) were studied by seeding individually weighed orchard and stand seed in different mixtures under harsh (direct seeding in field) and optimal (seeding in nursery) conditions. In the nursery experiment an increase in the seed weight from 3 to 7 mg increased the seedling height by 10-27% and total weight by 27-113%, and decreased the height/diameter ratio by 5-6% after 2 yrs. With elimination of seed weight effects, orchard seedlings were 2% taller than stand seedlings in year 2. Without elimination of seed weight effects, orchard seedlings were 7-13% taller. In the field experiment an increase in the seed weight from 3 to 7 mg increased seedling height by 18-65%, stem volume by 81-274% and the number of top-buds by 23-34% in year 5. After elimination of seed weight effects, orchard seedlings were 7-13% taller than stand seedlings and without elimination of seed weight effects 20-21% taller after 5 yrs. Even after elimination of both seed weight and genetic effects orchard seedlings were 3-9% larger than stand seedlings in the field experiment. In conclusion, the influence of seed weight and seed type on growth traits and slenderness is highly significant and the influence seems to be greater in harsh conditions.  相似文献   

15.
Baobab leaves form an important part of the local diet in Sahel countries and elsewhere in Africa. Existing leaf nutritional data and agroforestry performance information are based solely on Adansonia digitata L., the baobab of continental Africa. The introduction potential of Adansonia species from the center of diversity in Madagascar and from Australia remains untapped. To assess this potential, the mineral contents and B1 and B2 vitamin levels of dried baobab leaves were determined for five-year old trees of A. digitata, A. gibbosa (A. Cunn.) Guymer ex D. Baum, A. rubrostipa Jum. & H. Perrier (syn. A. fony Baill.), A. perrieri Capuron and A. za Baill. grown in an introduction trial in Mali. Nutritional data were evaluated against survival and vigor to identify promising germplasm. Leaf vitamin and crude protein contents were highest in the Madagascar species, especially A. rubrostipa (B1 88 mg 100 g−1, B2 187 mg 100 g−1, protein 20.7% dry weight). However, the local species far outperformed the introductions in survival, tree height, basal diameter and resistance to termites. We suggest grafting as a way of harnessing the vigor of well-adapted local baobab varieties to the superior nutritional profiles of A. rubrostipa and others. Cross-species grafting tests in Adansonia were successful, thus creating new agroforestry possibilities with different scion/rootstock combinations.  相似文献   

16.
Abstract

Wood in general and wooden studs in particular are often distorted owing to uneven shrinkage during the drying process in the sawmill. Twist is often the most detrimental of all types of distortion, and it is caused by spiral grain in combination with variations in moisture content. For sawmills, the objective is to produce dried, straight boards, and one method of dealing with boards with excessive spiral grain is to sort them out and then dry them in a pretwisted position to obtain straight boards after drying. A model using the finite element (FE) method for the simulation of drying twist distortions was first calibrated against laboratory experiments in which boards were dried with and without restraints and pretwists. After the calibration, the FE results were compared with industrial test results for boards that were dried without restraints or with restraints with zero pretwist, i.e. straight restraints. The FE model used an elastic–ideally plastic material model to obtain permanent deformations. The calibration was to set the yield stresses so that there was a good match between FE results and results from the laboratory experiments. The comparison between the industrial test results and the FE results showed that the FE model is capable of realistic simulations of drying boards with and without restraints and presumably also pretwists.  相似文献   

17.
Heterobasidion parviporum and Heterobasidion annosum are widely distributed root‐rot fungi that infect conifers throughout Europe. Infection of conifer stumps by spores of these pathogens can be controlled by treating fresh stumps with a competing non‐pathogenic fungus, Phlebiopsis gigantea. In this study, growth of three Latvian strains of P. gigantea and the biological control agent ‘Rotstop’ strain was evaluated in stem pieces of Norway spruce, Scots pine, lodgepole pine, Douglas‐fir, Weymouth pine, Siberian larch and Sitka spruce. The growth rates of one H. parviporum and one H. annosum isolate were also measured in the same stem pieces. The growth rate of P. gigantea varied greatly in wood of different conifer species. It was higher in the three pine species, lower in Norway spruce and lowest in Sitka spruce and Siberian larch, and in Douglas‐fir, this fungus did not grow. The largest area of wood occupied by P. gigantea was in lodgepole pine. Growth of Latvian isolates of P. gigantea in the wood of Pinus and Picea species was comparable to that of the Rotstop isolate. Consequently, stump treatment with local P. gigantea isolates should be recommended. However, our results suggest that Douglas‐fir stump treatment against Heterobasidion by P. gigantea may be ineffective and other stump treatment methods should be considered.  相似文献   

18.

This study investigated the stand structure in pine, spruce and deciduous forests in the border district of Finland and Russia. A total of 46 mature forest stands was selected as pairs, the members of each pair being as similar as possible with respect to their forest site type, age, moisture and topography. The stands were then compared between the two countries by means of basal areas and number of stems. The proportions of dominating tree species were 2-12% lower, and correspondingly the proportions of secondary tree species higher, in Russian forests. The density of the forest stock was also higher in each forest type in Russia. The forests in the two countries differed most radically in terms of the abundance of dead trees. The amount was two to four times higher in Russian deciduous and spruce forests, and in pine forests the difference was 10-fold. The stand structures indicated that Russian coniferous stands, in particular, were more heterogeneous than intensively managed pine and spruce stands in Finland.  相似文献   

19.

The root collar diameter and the height:diameter ratio are of particular importance in container-grown seedlings where a high density in the containers may produce spindly seedlings. Temperature regimes and light quality are known to affect plant growth. The aim of this study was to identify responses in Picea abies (L.) Karst. seedlings grown with light providing different red:far-red ratios and under temperature regimes with alternating day (DT) and night temperature (NT) from negative (DT < NT) to positive (DT > NT) difference (DIF) between DT and NT. Experiments were conducted in controlled environment chambers and in a daylight phytotron. Only limited thermoperiodic responses appeared in P . abies seedlings with respect to seedling height and dry weight accumulation. The formation of terminal buds, however, was clearly delayed in seedlings grown at negative DIF. The results indicate a requirement for day extension light that is high in far-red, to prevent terminal bud formation under natural short-day conditions. An extended study should be conducted to clarify the minimum level of light intensity and the optimal light quality needed to prevent terminal bud formation under natural short-day conditions.  相似文献   

20.
本文分析了CAD在设计中引起的正面和负面影响,并进行了系统的阐述,从而使设计者在应用中能够保持客观的态度。  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号