首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 203 毫秒
1.
选取丙烯酸酯、聚氨酯、丙烯酸-聚氨酯共聚物3种水性漆为滴液,用接触角测试仪对3种水性漆在杨木表面的接触角进行测试,对比分析其对杨木表面润湿性的影响。结果表明:未进行超纯水稀释的水性漆中,丙烯酸酯、共聚物水性漆在杨木径切面的润湿性优于弦切面,聚氨酯水性漆则反之;共聚物水性漆相比于其他两种漆润湿性更好,聚氨酯次之,丙烯酸酯水性漆的润湿性则相对较差。相比未进行超纯水稀释的水性漆,经稀释处理的3种水性漆在杨木表面的接触角均有不同程度的下降。接触角下降率分析表明:丙烯酸酯水性漆相比其他两种漆在杨木表面的润湿性更好,此外共聚物水性漆在杨木弦切面润湿性优于径切面,而其他两种水性漆则相反。  相似文献   

2.
水性树脂底漆对木材表面润湿性能的影响是决定木器涂装质量的关键因素。为了给木器水性漆涂装提供基本依据,选择松木、杉木、橡木、奥古曼和非洲紫檀5种木材,研究水性丙烯酸树脂底漆、水性丙烯酸改性聚氨酯底漆、双组分水性丙烯酸树脂对其表面润湿性能的影响。采用正交试验设计方案,以漆种、底漆质量分数、树种和干磨砂纸粒度为影响润湿性的因素,分别研究水性树脂底漆在木材弦、径切面的接触角大小和5种木材弦、径切面的孔槽比,分析影响木材表面润湿性的因素及原因。结果表明:4个因素水平中,底漆质量分数和漆种对木材表面润湿性的影响非常显著,树种对其影响显著,干磨砂纸粒度对其无显著影响;5种木材径切面的孔槽比高于弦切面,针叶材弦、径切面的孔槽比高于阔叶材,径切面的润湿性优于弦切面,针叶材表面润湿性优于阔叶材;此外,单组分水性树脂底漆在5种木材弦、径切面的润湿性优于双组分水性树脂底漆。因此,在木器水性漆高质量涂装中,对于不同木材种类应该选择合适的水性涂料及最优质量分数,才能保证涂装中底漆良好的质量。  相似文献   

3.
Abstract

Wood moisture content of coated panels of Scots pine sapwood was recorded during 24 months natural weathering in Vienna by logging electric resistance and temperature near the surface. Eight coating systems with various film thicknesses were used, including three solvent borne alkyd stains, three water borne acrylic stains and two water borne acrylic paints. At five sites in Europe wood moisture content of panels coated with three solvent borne alkyd stains, a brown acrylic stain and a white opaque acrylic paint was recorded weekly by changes in panel mass. Fluctuations in wood moisture content were influenced by the film thickness, water permeability and colour of the coating systems used. Degradation phenomena led to decreasing moisture protection of less durable coating systems over time of exposure. The exposure site clearly affected wood moisture content in the panels.  相似文献   

4.
观光木是广西大力发展的珍稀树种之一,具有优良的材性和机械加工性能.本文以观光木木材用的涂饰聚氨酯清漆和水性木器漆为研究对象,研究漆膜理化性能、光泽度和色度学特征的变化规律,为观光木木材高附加值实木制品的开发利用提供理论依据和信息.研究表明:①聚氨酯清漆的最佳涂饰工艺为:砂纸选用400#(表面粗糙度Ra为2.3),底漆涂布量为50 g/m2,面漆涂布量为70 g/m2,涂饰次数为3底3面;②水性木器漆涂料的最佳涂饰工艺为:砂纸选用320#(表面粗糙度Ra为2.9),底漆涂布量为100g/m2,面漆涂布量为120g/m2,涂饰次数为3底3面;③从漆膜理化性能、改善观光木表面光泽度和色度学特征以及节约原料看,聚氨酯清漆比水性木器漆有较明显的优势.  相似文献   

5.
Abstract

Development in surface mould growth on painted/unpainted wooden claddings and acting climatic factors were investigated over a period of 3 years. Eight wood substrates, including modified, preservative-treated and untreated wood, were tested in combination with three types of paint: (1) water-borne alkyd modified acrylic paint without fungicide; (2) solvent-borne alkyd paint without fungicide; and (3) ICP (internal comparison product). One set of samples was exposed unpainted. The samples were tested according to a modified version of EN 927-3. A logistic regression model was fitted to the data. The degree of mould growth varied with exposure time, coating typology, wood substrate, temperature and relative humidity. Exposure time and coating typology contributed most to the model. After 3 years of outdoor exposure unpainted panels and panels coated with solvent-borne paint without fungicide had more mould growth than panels coated with ICP and water-borne paint without fungicide. Unpainted oil/copper–organic preservative-treated claddings had higher resistance to mould growth than other unpainted wood substrates. Coated untreated pine and coated acetylated pine were more susceptible to mould growth than other coated wooden substrates.  相似文献   

6.
Sanding is the most common machining process used to prepare wood surfaces prior to coating. Hence, to improve surface quality and coating performance during this process, an optimal set of machining parameters should be established according to wood species and its final use. The effects of grit size and feed speed on surface properties and coating performance of red oak wood were studied. Surface quality was assessed by surface roughness, scanning electron micrographs, and wetting analyses. Coating performance was evaluated using pull-off adhesion tests on coated surfaces before and after an accelerated weathering. The results showed that smoother surfaces are obtained as the grit size number of the abrasive increased. On the other hand, minor differences were observed on cell damages and surface roughness as feed speed changed. Also, there was little difference among treatments concerning wetting behavior and surface energy. Pull-off strength was more affected by changes in grit size than feed speed. A P100-grit size program with a feed speed of 7 m/min resulted in a suitable roughness which provided good adhesion and high pull-off strength after aging test.  相似文献   

7.
Wettability of medium density fiberboard (MDF) surface affects paint or adhesive application and is, thus, of importance in the course of furniture manufacturing. This study investigated the effects of wood species, digester conditions and defibrator disc distance on the wettability properties. It was found that the wettability of the MDF significantly decreased with increasing the defibrator disc distance and increased with the increment in the severity of the digestion conditions. The highest wettability was found for samples made of beech wood having an average contact angle value of 74.5°, followed by poplar wood (76.5°), birch wood (79.7°), the mixture (1:1) of scots pine and beech wood (82.9°), and scots pine wood (86.4°), respectively.  相似文献   

8.
丙烯海松酸型聚氨酯涂料的研制   总被引:20,自引:3,他引:17  
以丙烯酸生松香和丙烯海松酸为原料,制备了NCO/OH双组分型,催化固化型及封闭型聚氨酯涂料,讨论了各种聚氨酯涂料的性能及影响涂料漆膜的各种因素。以丙烯酸改性松香为原料,制备的三种类型聚氨酯清漆与国产NCO/OH双组分型,催化固化型及封闭型聚氨酯清漆进行对比。结果表明,所得三种类型的聚氨酯清漆可分别替代同类型的国产品种。因其质优价廉具有广阔的应用前景。  相似文献   

9.
The improvement of wood surface wettability can clearly improve bonding properties, as well as enhance physical and mechanical properties of wood composites. In our investigation, the microwave plasma (MWP) technique was adopted to treat the surface of common teak. The treatment effect was evaluated by measuring the contact angles of liquids and calculating the free surface energy. The results show that the modification effect improved when the sample was located 120 mm from the resonance cavity, rather than at 80 mm. A MWP treatment over a short span of time is useful to lower the contact angles and improve the surface wettability considerably. The range of decreasing contact angles, tested by water, could reach 74% at a distance of 120 mm. __________ Translated from Journal of Northeast Forestry University, 2007, 35(12): 31–33 [译自: 东北林业大学学报]  相似文献   

10.
Implicit economic values of physical attributes of teak logs (girth, length, straightness and soundness) were estimated using hedonic regression. The influence of spatial and temporal variations on teak wood prices was also estimated. The auction prices of teak wood at various Timber Sales Depots of the Forest Department of Kerala State in India during the period 2006–2010 were used for the study. Traders ascribed over 80 % of variation in teak wood prices to girth, straightness and soundness of logs. A reduction in age at felling of teak plantations in forest areas is proposed. The study also underlines the need to continue tree improvement programs and silvicultural operations for the production of high quality teak wood and thereby increase the profitability of teak plantations.  相似文献   

11.
In this research, acoustic emission technology was used to estimate the moisture excluding effectiveness of coatings on wood. Moisture interaction with wood causes damage, and coatings such as paints and varnishes can effectively limit this interaction. Over time, the moisture excluding effectiveness of wood is reduced by the actions of weathering and the resulting wood-water interaction leads to problems due to the dimensional instability of the wood. Five coating types, at two spreading levels, were applied to samples of southern yellow pine. The samples were exposed to three weathering conditions to simulate the effects of exposure then immersed in water while the moisture interaction was monitored using acoustic emission monitoring equipment. Cumulative counts as well as changes in size and moisture content were measured or calculated. The results show that acoustic emission technology is an effective and sensitive estimator of the moisture excluding effectiveness of coatings on wood. The acoustic emission method is sensitive to local changes and coating fractures whereas the more traditional methods are sensitive to gross changes in sample characteristics. Of five coatings tested, the most effective one was found to be an oil-based paint, and the worst performance was by a water-based, clear poly-urethane. Received: 10 September 1998  相似文献   

12.
李新功  郑霞  魏立 《林业科技》2009,34(5):48-50
仿古实木复合地板属于实木复合地板的一种,其表面立体感强,表面纹理清晰逼真,辅以仿古色彩映衬,给人感觉悠远古朴。涂装工序是仿古实木复合地板加工的重要工序,该工序的加工工艺对地板的质量,特别是仿古效果非常重要。研究表明,采用辊涂生产工艺,既满足了各项涂层指标要求,同时还节省油漆,更环保。  相似文献   

13.
研究了两种涂料配方的不同配比对木质复合地板尺寸稳定性的影响,结果表明:以醇酸清漆为主的涂料对地板产品进行后期处理,在产品尺寸稳定性和成本方面均优于其它涂料,合理选取涂料组分和配比,不仅能提高产品的尺寸稳定性,而且提高产品外观的美观度。  相似文献   

14.
The effects of high temperature, moisture, and mechanical action during the thermo-hydro-mechanical (THM) processing, on the changes in surface properties of poplar, namely, surface color, roughness, wettability, and microstructure, were investigated in this study. The correlation between observed changes in surface properties and chemical characteristics was also analyzed. Poplar woods with high moisture content were compressed using different pressures at temperature of 160 °C for four different periods. The wood surfaces became darker and smoother, and their surface free energy decreased significantly after the THM process. THM process markedly reduced surface hygroscopicity compared to the control wood. The cell lumens of THM wood became narrow with increasing compression ratio due to the enhancing high pressure. Collapse and fractures of cell walls developed during THM treatment. Furthermore, results indicated that a series of chemical reactions in different components of wood took place during THM process, such as degradation of hemicelluloses, condensation of lignin, and decomposition of extractives. In turn, these chemical modifications contributed to the darkening of color as well as the reduction of wettability and surface free energy of THM wood.  相似文献   

15.
Effect of artificial weathering on the wettability of three heat-treated North American wood species (jack pine, aspen, and birch) is studied from the point of view of the structural and chemical changes taking place on the wood surface. Weathering increases wettability of all three heat-treated woods by water. Changes in wettability during artificial weathering differ according to heat treatment procedure and wood species and are likely due to combination of structural and chemical changes of the surfaces. Scanning electron microscopic analysis indicates that cracks form due to degradation taking place during weathering. As a result, water has easier entry into the cell wall, which consequently increases wettability. IR spectra suggest that the OH/CH2 ratio for heat-treated specimens is inversely proportional to the contact angle regardless of the type of wood species. The presence of cellulose-rich layer on wood surface and increasing amount of amorphous cellulose transformed from crystallized cellulose due to weathering result in increase in hydroxyl; consequently, it increases heat-treated wood wettability.  相似文献   

16.
We used silane coupling agents to improve the bonding ability between wheat straw particles and UF resin, and investigated surface properties (wettability and surface roughness) and hardness of parti-cleboard made from UF-bonded wheat straw (Triticum aestivum L.) combined with poplar wood as affected by silane coupling agent content and straw/poplar wood particle ratios. We manufactured one-layered particleboard panels at four different ratios of straw to poplar wood par-ticles (0%, 15%, 30% and 45% wheat straw) and silane coupling agent content at three levels of 0, 5% and 10%. Roughness measurements, average roughness (Ra), mean peak-to-valley height (Rz), and root mean square roughness (Rq) were measured on unsanded samples by using a fine stylus tracing technique. We obtained contact angle measurements by using a goniometer connected to a digital camera and computer sys-tem. Boards containing greater amounts of poplar particles had superior hardness compared to control samples and had lower wettability. Panels made with higher amounts of silane had lower Rq values.  相似文献   

17.
以试件轮廓算数平均值作为表面粗糙度的判别标准,采用格丽斯仿古涂饰工艺对改性杨木进行表面涂饰,分析涂饰工艺对改性杨木表面粗糙度的影响。结果表明:砂纸目数对改性杨木表面漆膜粗糙度影响最大,底漆喷涂道数影响最小。漆膜粗糙度优化工艺条件为底漆喷涂道数2道、砂纸目数240目、素材修色喷涂道数1道、表面修色道数1道。  相似文献   

18.
Growth, wood quality parameters and productivity estimations of 12-year-old teak (Tectona grandis L.f.) grown under three agroforestry systems, namely unmanaged block (Bum), unmanaged line on the farm boundary (Lum) and intensively managed block (Bim) plantations are studied. Mean annual increment (MAI) of 0.020, 0.006 and 0.016 m3 tree?1 year?1 was recorded in Lum, Bum and Bim, respectively. Overall growth performance of teak raised in Lum, plantation appears to be better than two block plantations (Bum and Bim). For evaluating various wood quality parameters, tree logs from each plantation were tested for different physical and mechanical properties according to the standard procedures. The wood quality of Bum was found to be comparatively superior to Bim and much better than those of Lum. The 12-year-old farm teak trees from three systems exhibited lower average values of different wood quality parameters compared to mature forest teak. Since physical and strength properties of Bum were inferior compared to Lum and Bim, its exploitation is not advisable at this stage. Line plantation, however, releases land for cultivation of arable crops and does not demand any special silvicultural management as required by Bim. Although, total extractable volume of teak wood available after 12-years of age from Bum was much smaller compared to Bim or Lum, its commercial exploitation at an early age may be preferred over other two practices due to better wood quality and lower management cost. For optimum economic utilization and mechanical maturity of wood, harvesting of block plantation may be delayed for about 10-15 years because growth volume and strength properties are expected to improve with age of tree.  相似文献   

19.
木材切削表面粗糙度的影响因素很多且组成复杂,较难进行准确的测定评价。从木材切削表面粗糙度的影响因素、不同测试方法及现行测定评价标准三个方面,对木材切削表面粗糙度相关研究进行综述,基于现状提出了完善木材切削表面粗糙度测定评价方法的建议。  相似文献   

20.
Summary Radiata pine veneers and blocks were exposed to natural weathering under Australian summer conditions over a period of 30 days. Infrared spectroscopy revealed that there was perceptible surface delignification after 4 hours exposure, substantial surface delignification after 3 days exposure and almost complete surface delignification after 6 days. Rapid lignin degradation was also suggested by measurements of the acid insoluble lignin content of weathered veneers. Viscometry determinations on holocellulose samples from weathered veneers and unweathered controls indicated significant depolymerisation of cellulose after 4 days exposure. A tape test was used to assess the adhesion of acrylic latex primers to weathered blocks. The adhesion of exterior acrylic primers decreased on weathered wood surfaces and was significantly lower on specimens that were weathered for 5 to 10 days. An oil-modified acrylic primer showed greater adhesion to weathered wood surfaces. Primer adhesion was lower on weathered radial surfaces than on similarly exposed tangential surfaces. The practical implications of these findings for the coating of exterior wood with acrylic latex primers are discussed briefly.The authors wish to thank Dr. A. J. Michell for FTIR spectral determinations and the Australian Research Council small grants scheme for financially supporting part of the work  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号