首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 15 毫秒
1.
Whey protein concentrate solutions (12% w/v, pH 6.65 +/- 0.05) were pressure treated at 800 MPa for 20-120 min and then examined using size exclusion chromatography (SEC), small deformation rheology, transmission electron microscopy, and various types of one-dimensional (1D) and two-dimensional (2D) polyacrylamide gel electrophoresis (PAGE). The pressure-treated samples showed a time-dependent loss of native whey proteins by SEC and 1D PAGE and a corresponding increase in non-native proteins and protein aggregates of different sizes. These aggregates altered the viscosity and opacity of the samples and were shown to be cross-linked by intermolecular disulfide bonds and by noncovalent interactions using 1D PAGE [alkaline (or native), sodium dodecyl sulfate (SDS), and SDS of reduced samples (SDS(R))] and 2D PAGE (native:SDS and SDS:SDS(R)). The sensitivity of the major whey proteins to pressure was in the order beta-lactoglobulin B (beta-LG B) > beta-LG A > bovine serum albumin (BSA) > alpha-lactalbumin (alpha-LA), and the large internal hydrophobic cavity of beta-LG may have been partially responsible for its sensitivity to high-pressure treatments. It seemed likely that, at 800 MPa, the formation of a beta-LG disulfide-bonded network preceded the formation of disulfide bonds between alpha-LA or BSA and beta-LG to form multiprotein aggregates, possibly because the disulfide bonds of alpha-LA and BSA are less exposed than those of beta-LG either during or after pressure treatment. It may be possible that intermolecular disulfide bond formation occurred at high pressure and that hydrophobic association became important after the high-pressure treatment.  相似文献   

2.
Surface tension, foamability, and foam stability kinetics have been measured for the pure proteins bovine serum albumin (BSA) and beta-lactoglobulin, before and after aqueous solutions of the proteins had been subjected to different drying conditions, and also for whey protein concentrate (WPC). Pure proteins were air-dried, at 78 or 88 degrees C, in the presence and absence of sucrose or trehalose, at a mass ratio of 5:1 sugar/protein. WPC was spray-dried in the presence of various sugars: trehalose, sucrose, lactose, and lactitol. Spray-drying WPC without sugars resulted in a dramatic decrease in the foam stability, whereas drying in the presence of sugars gave better retention of the original foaming properties. Trehalose in particular resulted in almost complete retention of the foam stability observed for the nondried WPC. Pure beta-lactoglobulin showed similar behavior, but trehalose did not seem to afford the same protection to BSA.  相似文献   

3.
The unfolding of beta-lactoglobulin during high-pressure treatment and its refolding after decompression were studied by 1H NMR and 2H/1H exchange at pH 6.8 and 2.5 and at 37 and 25 degrees C. The extent of unfolding increased with the pressure level. The structure of beta-lactoglobulin required higher pressures to unfold at pH 2.5 than at pH 6.8. More flexibility was achieved at 37 degrees C than at 25 degrees C. Results indicated that the structural region formed by strands F, G, and H was more resistant to unfold under acidic and neutral conditions. The exposure of Trp19 at an earlier time, as compared to other protein regions, supports the formation of a swollen structural state at pH 2.5. Refolding was achieved faster when beta-lactoglobulin was subjected to 200 MPa than to 400 MPa, to 37 degrees C than to 25 degrees C, and to acidic than to neutral pH. After treatment at 400 MPa for 20 min at neutral pH, the protein native structure was not recovered. All samples at acidic pH showed that the protein quickly regained its structure. Hydrolysis of beta-lactoglobulin by pepsin and chymotrypsin could be related to pressure-induced changes in the structure of the protein. Compared to the behavior of the protein at atmospheric pressure, no increased proteolysis was found in samples with no increased flexibility (100 MPa, 37 degrees C, pH 2.5). Slightly flexible structures were associated with significantly increased proteolysis (100 MPa, 37 degrees C, pH 6.8; 200 MPa, 37 degrees C, pH 2.5). Highly flexible structures were associated with very fast proteolysis (>or=200 MPa, 37 degrees C, pH 6.8; >or=300 MPa, 37 degrees C, pH 2.5). Proteolysis of prepressurized samples improved only when the protein was significantly changed after the pressure treatment (400 MPa, 25 degrees C, 20 min, pH 6.8).  相似文献   

4.
Modification of the functionality of whey proteins using microbial transglutaminase (TGase) has been the subject of recent studies. However, changes in rheological properties of whey proteins as affected by extensive cross-linking with TGase are not well studied. The factors affecting cross-linking of whey protein isolate (WPI) using both soluble and immobilized TGase were examined, and the rheological properties of the modified proteins were characterized. The enzyme was immobilized on aminopropyl glass beads (CPG-3000) by selective adsorption of the biotinylated enzyme on avidin that had been previously immobilized. WPI (4 and 8% w/w) in deionized water, pH 7.5, containing 10 mM dithiothreitol was cross-linked using enzyme/substrate ratios of 0.12-10 units of activity/g WPI. The reaction was carried out in a jacketed bioreactor for 8 h at 40 degrees C with continuous circulation. The gel point temperature of WPI solutions treated with 0.12 unit of immobilized TGase/g was slightly decreased, but the gel strength was unaffected. However, increasing the enzyme/substrate ratio resulted in extensive cross-linking of WPI that was manifested by increases in apparent viscosity and changes in the gelation properties. For example, using 10 units of soluble TGase/g resulted in extensive cross-linking of alpha-lactalbumin and beta-lactoglobulin in WPI, as evidenced by SDS-PAGE and Western blotting results. Interestingly, the gelling point of WPI solutions increased from 68 to 94 degrees C after a 4-h reaction, and the gel strength was drastically decreased (lower storage modulus, G'). Thus, extensive intra- and interchain cross-linking probably caused formation of polymers that were too large for effective network development. These results suggest that a process could be developed to produce heat-stable whey proteins for various food applications.  相似文献   

5.
The effect of heat treatment on the IgE binding ability of beta-lactoglobulin, as pure protein or in whole milk, was studied by inhibition of IgE antibody binding using FEIA-CAP inhibition. A slight but significant decreased IgE binding was seen between unheated and heat-treated beta-lactoglobulin solution at 74 degrees C (IC(50) = 2.03 and 3.59 microg/mL, respectively, p = 0.032). A more pronounced decrease was found at 90 degrees C with an IC(50) of 8.45 microg/mL (p = 0.014). The inhibition of IgE binding of milk after heat treatment at 90 degrees C was also significantly decreased (p = 0.007). However, at all heat treatments, a similar total amount of IgE antibodies could be inhibited at a sufficiently high concentration of beta-lactoglobulin. The inhibiting ability of beta-lactoglobulin was significantly impaired in some fermented acidified milk products such as yogurt as compared to that in nonfermented milk (p < 0.001). There was only a small difference of IgE binding between the native forms of genetic variants A and B.  相似文献   

6.
Lactoperoxidase-induced protein oxidation in milk   总被引：4，自引：0，他引：4  
The reaction between lactoperoxidase (LPO) and H(2)O(2) in the presence of bovine serum albumin (BSA), beta-lactoglobulin, or casein was investigated for the formation of protein radicals by freeze-quench electron spin resonance (ESR) and by the formation of the protein oxidation product, dityrosine. The presence of BSA resulted in a dramatic change after 1 min of reaction in the obtained ESR spectrum compared with the spectrum obtained for LPO and H(2)O(2) alone. Furthermore, experiments employing BSA or beta-lactoglobulin resulted in the formation of long-lived protein radicals detectable 10 min after initiation of the reaction. The presence of casein resulted in a minor change in the fine structure of the ESR spectrum after 1 min of reaction compared with LPO and H(2)O(2) alone, but no difference between the two reaction mixtures could be observed after 10 min of reaction. The formation of dityrosine could be detected in reaction mixtures containing LPO and H(2)O(2) after 1 and 10 min of incubation at 25 degrees C both in the absence and in the presence of BSA, beta-lactoglobulin, or casein. The presence of casein resulted in an increased dityrosine concentration compared with the reaction with LPO and H(2)O(2) alone. Endogenous LPO in unpasteurized milk was activated at 25 degrees C by adding 1 mM H(2)O(2). Radical species could be detected directly in the milk by freeze-quench ESR during the initial phase of the reaction, and dityrosine could be measured after 4 h of incubation. The role of LPO activity in the formation of ESR detectable radical species and dityrosine in milk was further verified in ultrahigh temperature (UHT) milk with no endogenous enzyme activity, as the formation of ESR detectable radical species and dityrosine took place in UHT milk only upon the addition of both H(2)O(2) and exogenous LPO.  相似文献   

7.
Traditionally, milk has been heat treated to control microorganisms and to alter its functionality, for example, to increase its heat stability. Pressure treatment has been considered as a possible alternative for microorganism control, but some of the functionality-related milk protein interactions have not been explored. The present study used two novel two-dimensional polyacrylamide gel electrophoresis (2D PAGE) methods to explore the differences in the irreversible disulfide bond changes among the milk proteins after four common heat treatments and after 30-min pressure treatments of milk at 200, 400, 600, and 800 MPa at ambient temperature (22 degrees C). The pasteurizing heat treatment (72 degrees C for 15 s) denatured and aggregated only a few minor whey proteins, but the high heat treatments (100 degrees C for 120 s, 120 degrees C for 120 s, and 140 degrees C for 5 s) formed disulfide-bonded aggregates that included a high proportion of all of the whey proteins and kappa-casein (kappa-CN) and a proportion of the alpha(s2)-CN. Pressure treatment of milk at 200 MPa caused beta-lactoglobulin (beta-LG) to form disulfide-bonded dimers and incorporated beta-LG into aggregates, probably disulfide-bonded to kappa-CN. The other whey proteins appeared to be less affected at 200 MPa for 30 min. In contrast, pressure treatment at 800 MPa incorporated beta-LG and most of the minor whey proteins, as well as kappa-CN and much of the alpha(s2)-CN, into aggregates. The accessibility of alpha(s2)-CN and formation of complexes involving alpha(s2)-CN, kappa-CN, and whey proteins in the pressure treated milk is an important novel finding. However, only some of the alpha-lactalbumin was denatured or incorporated into the large aggregates. These and other results show that the differences between the stabilities of the proteins and the accessibilities of the disulfide bonds of the proteins at high temperature or pressure affect the formation pathways that give the differences among the resultant aggregates, the sizes of the aggregates, and the product functionalities.  相似文献   

8.
The mechanism that leads to a decreased aggregation of beta-lactoglobulin in the presence of dextran sulfate and lambda-carrageenan was investigated by assessing changes in the denaturation thermodynamics and protein structure. Differential scanning calorimetry results showed that the denaturation temperature (Tp) was about 4.6 degrees C higher in the presence of dextran sulfate, as compared with beta-lactoglobulin alone, whereas in the presence of lambda-carrageenan the difference in Tp was about 1.2 degrees C. Changes in protein structure studies using near-UV circular dichroism (CD) provided support for the calorimetric results. The transition midpoint (Tm) for denaturation of beta-lactoglobulin was about 5 degrees C higher in the presence of dextran sulfate than that found with beta-lactoglobulin alone and about 2 degrees C in the presence of lambda-carrageenan. Thermal modifications of the tertiary structure of beta-lactoglobulin were irreversible at temperatures above 67 degrees C; the addition of dextran sulfate reduced the extent of such modifications. Far-UV CD studies indicated that the addition of dextran sulfate or lambda-carrageenan did not affect secondary structure changes of beta-lactoglobulin upon heating. These studies indicate that dextran sulfate and lambda-carrageenan can enhance the stability of beta-lactoglobulin and thereby inhibit heat denaturation and aggregation.  相似文献   

9.
Molecular complexes based on proteins and ionic polysaccharides have considerable potential for encapsulation of functional food components, but their widespread utilization is limited because their structure is highly sensitive to pH and ionic strength. We have investigated the possibility of creating stable hydrogel particles by thermal treatment of protein (beta-lactoglobulin) and cationic polysaccharide (chitosan) mixtures. Mixed solutions of beta-lactoglobulin (0.5 wt %) and chitosan (0.1 wt %) were prepared at various pH's (3-8) and were heated (80 degrees C for 20 min). Prior to heating, the biopolymer mixtures formed molecular complexes at pH values where there was an electrostatic attraction between the protein and the polysaccharide: soluble complexes at pH 4.5; complex coacervates at pH 5.0 and 5.5; precipitates at pH>5.5. After heating, relatively small (d approximately 140 nm) and cationic (zeta>+20 mV) hydrogel particles were formed at pH 4.5, but much larger aggregates were formed at pH 5.0 and higher (d>1000 nm). The thermally treated hydrogel particles formed at pH 4.5 maintained their initial particle size when the pH was subsequently adjusted within the range pH 3-5, but they aggregated when the pH was adjusted to >pH 5 because of a reduction in the magnitude of their electrical charge. This study suggests that hydrogel particles can be formed by heating mixed protein-polysaccharide systems under controlled conditions. These hydrogel particles may be useful for encapsulation of functional food components.  相似文献   

10.
The physical aggregation of commercial whey protein isolate (WPI) and purified beta-lactoglobulin was studied by ultrasound spectroscopy. Protein samples were dialyzed to achieve constant ionic strength backgrounds of 0.01 and 0.1 NaCl, and gelation was induced in situ at constant temperatures (from 50 to 75 degrees C) or with a temperature ramp from 20 to 85 degrees C. Changes in the ultrasonic properties were shown in the early stages of heating, at temperatures below those reported for protein denaturation. During heating, the relative ultrasound velocity (defined as the difference between sample velocity and reference velocity) decreased continuously with temperature, indicating a rearrangement of the hydration layer of the protein and an increase in compressibility of the protein shell. At temperatures <50 degrees C the ultrasonic attenuation decreased, and <65 degrees C both velocity and attenuation differentials showed increasing values. A sharp decrease in the relative velocity and an increase in the attenuation at 70 degrees C were indications of "classical" protein denaturation and the formation of a gel network. Values of attenuation were significantly different between samples prepared with 0.01 and 0.1 M NaCl, although no difference was shown in the overall ultrasonic behavior. WPI and beta-lactoglobulin showed similar ultrasonic properties during heating, but some differences were noted in the values of attenuation of WPI solutions, which may relate to a less homogeneous distribution of aggregates caused by the presence of alpha-lactalbumin and other minor proteins in WPI.  相似文献   

11.
Fish oil was incorporated into milk under different homogenization temperatures (50 and 72 degrees C) and pressures (5, 15, and 22.5 MPa). Subsequently, the oxidative stability of the milk and changes in the protein composition of the milk fat globule membrane (MFGM) were examined. Results showed that high pressure and high temperature (72 degrees C and 22.5 MPa) resulted in less lipid oxidation, whereas low pressure and low temperature (50 degrees C and 5 MPa) resulted in faster lipid oxidation. Analysis of protein oxidation indicated that especially casein was prone to oxidation. The level of free thiol groups was increased by high temperature (72 degrees C) and with increasing pressure. Furthermore, SDS-PAGE and confocal laser scanning microscopy (CLSM) indicated that high temperature resulted in an increase in beta-lactoglobulin adsorbed at the oil-water interface. This was even more pronounced with higher pressure. Less casein seemed to be present at the oil-water interface with increasing pressure. Overall, the results indicated that a combination of more beta-lactoglobulin and less casein at the oil-water interface gave the most stable emulsions with respect to lipid oxidation.  相似文献   

12.
The objective of this study was to investigate the influence of globular protein interfacial cross-linking on the in vitro digestibility of emulsified lipids by pancreatic lipase. 3% (wt/wt) corn oil-in-water emulsions stabilized by either lecithin or beta-lactoglobulin were prepared (pH 7). A portion of the beta-lactoglobulin stabilized emulsions was subjected to a heat treatment known to cross-link the adsorbed globular proteins (85 degrees C, 20 min). Pancreatic lipase and bile extract were then added to each emulsion at 37 degrees C (pH 7) and the evolution of the particle charge, particle size, appearance and free fatty acids released were measured over a period of 2 h. The rate and extent of lipid digestion did not differ greatly between lecithin and beta-lactoglobulin stabilized emulsions, nor did it differ greatly for unheated (BLG-U) or heated (BLG-H) beta-lactoglobulin stabilized emulsions. For example, the initial rate of lipid digestion was found to be 3.1, 3.4, and 2.3 mM fatty acids s(-1) m(-2) of lipid surface for droplets stabilized by BLG-U, BLG-H, and lecithin, respectively. Pancreatic lipase was able to adsorb to the droplet surfaces and access the emulsified lipids, regardless of the initial interfacial composition and the fact that some of the original emulsifier appeared to remain at the oil-water interface during digestion. These results help to explain why the human body is so efficient at digesting dietary triacylglycerols.  相似文献   

13.
Bovine serum albumin (BSA) was incubated for 24 h in the presence of 10 mM ribose (RI), methyl linoleate hydroperoxides, or the secondary products of methyl linoleate oxidation (SP), at five temperatures (25, 37, 50, 80, and 120 degrees C) and different pHs (4, 7, and 10), to study the influence of these variables in the browning, fluorescence, amino acid losses, and pyrrolization of the modified proteins. All treated proteins exhibited similar colors and fluorescence spectra, and the spectra of their Ehrlich adducts were also analogous. However, at 25-50 degrees C the proteins treated with oxidized lipids exhibited higher color changes, amino acid losses, and pyrrolization than the BSA treated with RI, and these effects were much higher in proteins treated with RI at 80-120 degrees C. The effect of pH was similar in proteins treated with RI or SP. These results suggested a similarity for browned proteins obtained from both carbohydrates and oxidized lipids. In addition, both reactions seem to be complementary, because melanoidin formation derived from oxidized lipids can be produced under conditions different from those carbohydrate/protein reactions.  相似文献   

14.
Hydrolysis of beta-lactoglobulin (in an equimolar mixture of the A and B variant) by trypsin in neutral aqueous solution [pH 7.7 at 25 degrees C, ionic strength 0.08 (NaCl)] was followed by capillary electrophoresis and thermodynamic parameters derived from a Michaelis-Menten analysis of rate data obtained at 10, 20, 30, and 40 degrees C for disappearance of beta-lactoglobulin. Enthalpy of substrate binding to the enzyme and the energy of activation for the catalytic process were found to have the values, DeltaH(bind) = -28 +/- 4 kJ mol(-)(1) and E(a) = 51 +/- 18 kJ mol(-)(1), respectively. Thus, beta-lactoglobulin shows an enthalpy of activation for free substrate reacting with free enzyme of about 21 kJ mol(-)(1), corresponding to a transition state stabilization of 60 kJ mol(-)(1) when compared to acid-catalyzed hydrolysis. The catalytic efficiency of trypsin in hydrolysis of beta-lactoglobulin is increased significantly by temperature; however, this effect is partly counteracted by a weaker substrate binding resulting in an increase by only 25%/10 degrees C in overall catalytic efficiency.  相似文献   

15.
Solutions obtained by heating carrot roots in water (stocks) are widely used in the food industry, but little information is available regarding the metabolites (intermediates and products of metabolism) found in the stock. The effect of treatment temperature and duration on the sugar composition of stocks was investigated directly by quantitative (1)H NMR spectroscopy, to understand the extraction mechanism when processing at 100 degrees C. Stocks prepared at three different temperatures (50, 75, and 100 degrees C) were investigated for up to 36 h. Three sugars (sucrose, glucose, and fructose) were detected and quantified. The concentrations of these three sugars reached a maximum after 9 h when the temperature of treatment was 50 or 75 degrees C. At 100 degrees C, the sucrose concentration reached a maximum after 3 h, whereas the concentration of glucose and fructose was still increasing at that time. Comparison of the kinetic composition of these carrot stocks with that of model sugar solutions leads to the proposal that the changes in stock composition result from sugar diffusion, sucrose hydrolysis, and hydroxymethylfurfural (HMF) formation.  相似文献   

16.
In an attempt to elevate temperature to facilitate glycation, a nonenzymatic reaction by incubation of bovine serum albumin (BSA) and fructose at 50 °C for 24 h has been developed. As conducted and compared to a routine procedure by incubation of BSA and fructose at 37 °C for 168 h, the reactant fluorescence intensities and SDS-PAGE-detected glycated BSA quantities produced by both test temperatures increased with time of incubation. As the Amadori products and α-dicarbonyl compounds during incubation were quantified, both quantities produced at each temperature also increased with an increase of time of incubation, and their trends of changes at both temperatures were similar. In practical application for the detection and screening of the antiglycative phytochemicals, each of 20 peanut root extracts was introduced to a series of BSA-fructose solutions and incubated at 37 and 50 °C for 168 and 24 h, correspondingly. All extracts exhibited notable activities and varied depending on peanut origins. Pair comparison of the resultant antiglycative activities determined at 37 and 50 °C showed that both determined activities for each peanut root extract deviated limitedly. As further analyzed, SDS-PAGE-detected glycated BSA quantities formed at 50 °C were closely proportional to the antiglycative activities determined on the basis of their fluorescence intensities. It is of merit to demonstrate that fluorescence-based determination of BSA-fructose reactant after incubation at 50 °C for 24 h is practical and time-saving in the detection and screening of antiglycative phytochemicals.  相似文献   

17.
Raman spectroscopy was used to elucidate structural changes of beta-lactoglobulin (BLG), whey protein isolate (WPI), and bovine serum albumin (BSA), at 15% concentration, as a function of pH (5.0, 7.0, and 9.0), heating (80 degrees C, 30 min), and presence of 0.24% kappa-carrageenan. Three data-processing techniques were used to assist in identifying significant changes in Raman spectral data. Analysis of variance showed that of 12 characteristics examined in the Raman spectra, only a few were significantly affected by pH, heating, kappa-carrageenan, and their interactions. These included amide I (1658 cm(-1)) for WPI and BLG, alpha-helix for BLG and BSA, beta-sheet for BSA, CH stretching (2880 cm(-1)) for BLG and BSA, and CH stretching (2930 cm(-1)) for BSA. Principal component analysis reduced dimensionality of the characteristics. Heating and its interaction with kappa-carrageenan were identified as the most influential in overall structure of the whey proteins, using principal component similarity analysis.  相似文献   

18.
Botrytis cinerea is an important fungal pathogen particularly dreaded in the cool climate vineyard. It is responsible for important damage, especially the decrease in foamability of sparkling wines, such as Champagne. Different studies have shown that proteins are largely involved in the stabilization of Champagne foam despite their low concentration. Other works demonstrated changes in the electrophoretic characteristics of must proteins originating from botrytized grapes, although the cause of such alterations was never explained. In the first part of this study, results showed the release by B. cinerea of 3.5 mg/L total proteins in a synthetic liquid medium. Among these proteins, the presence of a protease activity on bovine serum albumin (BSA) and must proteins was demonstrated by using a colorimetric method and sodium dodecyl sulfate-polyacrylamide gel electrophoresis. In the model wine, the Bradford method showed a BSA loss of 66% after 24 h and a loss of 96% after 120 h. In the same model wine, the soluble must protein concentration decreased by 35% after 1 week and by 53% after 2 weeks while the control showed no protein loss. B. cinerea proteases were then able to degrade BSA and must proteins and were above all active at must and wine pH and in the presence of ethanol and SO(2). The second part of this work was dedicated to the relationship between the presence of B. cinerea proteases and its effects on the synthetic wine foaming properties. The addition of a B. cinerea culture medium (1/33 v/v) to the synthetic wine containing 21 mg/L soluble grape proteins induced a decrease in foamability by 60% after 1 week. For BSA in the model wine, the foamability decreased by 32% after 24 h and by 95% after 120 h, as shown by the colorimetric method. These experiments demonstrate for the first time the relationship between B. cinerea protease activity and the decrease in wine foaming properties.  相似文献   

19.
Thermal, rheological, and microstructural properties of myosin (1 and 2% protein) were compared to mixtures of 1% myosin and 1% heat-denatured beta-lactoglobulin aggregates (myosin/HDLG) and 1% myosin and 1% native beta-lactoglobulin (myosin/beta-LG) in 0.6 M NaCl and 0.05 M sodium phosphate buffer, pH 6.0, 6.5, and 7.0 during heating to 71 degrees C. Thermal denaturation patterns of myosin and myosin/HDLG were similar except for the appearance of an endothermic peak at 54-56 degrees C in the mixed system. At pH 7.0, 2% myosin began to gel at 48 degrees C and had a storage modulus (G') of 500 Pa upon cooling. Myosin/HDLG (2% total protein) had a gel point of 48 degrees C and a G' of 650 Pa, whereas myosin/beta-LG had a gel point of 49 degrees C but the G' was lower (180 Pa). As the pH was decreased, the gel points of myosin and myosin/HDLG decreased and the G' after cooling increased. The HDLG was incorporated within the myosin gel network, whereas beta-LG remained soluble.  相似文献   

20.
The denaturation, aggregation, and rheological properties of chicken breast muscle myosin, beta-lactoglobulin (beta-LG), and mixed myosin/beta-LG solutions were studied in 0.6 M NaCl, 0.05 mM sodium phosphate buffer, pH 7.0, during heating. The endotherm of a mixture of myosin and beta-LG was identical to that expected if the endotherm of each protein was overlaid on the same axis. The maximum aggregation rate (AR(max)) increased, and the temperature at the AR(max) (T(max)) and initial aggregation temperature (T(o)) decreased as the concentration of both proteins was increased. The aggregation profile of <0.5% myosin was altered by the presence of 0.25% beta-LG. Addition of 0.5-3.0% beta-LG decreased storage moduli of 1% myosin between 55 and 75 degrees C, but increased storage moduli (G') when heated to 90 degrees C and after cooling. beta-LG had no effect on the gel point of > or =1.0% myosin, but enhanced gel strength when heated to 90 degrees C and after cooling. After cooling, the G' of 1% myosin/2%beta-LG gels was about 1.7 times greater than that of gels prepared from 2% myosin/1% beta-LG.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号