首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 31 毫秒
1.
In this study, the process of electrospinning was used on nanofiber yarn formation. The parameters in the study were flow rate and twist multiplier, which were discussed their effect on yarn formation. Further, a normal yarn was used as the core yarn, which was wrapped with nanofibers to form a new type of composite yarn. In this part of the experiment, the parameters were flow rate and collector width, which were discussed in terms of their effect on the yarn quality of nanofibrous composite yarn. The experiment result showed the diameter of the nanofiber was between 220 nm to 260 nm. When the collector width was 5 mm, there was a high quality wrapping resulting in good yarn, with the nanofiber composite yarn having a strength of 3.25 (cN/dtex).  相似文献   

2.
In this study, various concentrations of polyethylene terephthalate (PET) polymeric solution were investigated to produce hollow nanofiber yarn. First, the electrospining apparatus was designed in a way that to put PVA multifilament in the core and to twist PET nanofibers onto multifilament yarn as a sheath simultaneously, followed by dissolving PVA yarn in hot water, PET hollow nanofiber yarn was produced. In this survey, it has been observed that the average thickness of sheath increased by increasing concentrations of PET polymeric solution. Results showed that maximum efficiency of extracting the PVA multifilament from the hollow yarn under certain conditions (concentration of 18 % (w/v) of PET, applied voltage of 10 kV, and flow rate of 0.0526 ml/h) was more than 85 %. The mechanical and physical properties of PET hollow yarns were investigated and indicated that the hollow nanofiber yarns at concentration of 30 % and 18 % polymeric solution had the lowest strength and the highest regain moisture, respectively.  相似文献   

3.
Electrospinning is a simple and cost-effective method to prepare fiber with nanometer scale. More importantly, 3D flexible nanofiber yarns that fabricated by electrospinning have shown excellent application prospects in smart textiles, wearable sensors, energy storage devices, tissue engineering, and so on. However, current methods for preparing electrospinning nanofiber yarns had some limitations, including low yarn yield and poor yarn structure. In this paper, a stepped airflow-assisted electrospinning method was designed to prepare continuously twisted nanofiber yarn through introducing stepped airflow into traditional electrospinning system. The stepped airflow could not only help to improve nanofiber yield, but also good for controlling the formed nanofibers to be deposited in a small area. In addition, the experimental methods of single factor variables were used to study the effects of stepped airflow pressure, applied voltage, spinning distance, solution flow rate, air pumping volume and friction roller speed on nanofiber yarn yield, nanofiber diameter, yarn twist and mechanical property. The results showed that prepared nanofiber yarns exhibited perfect morphologies and the yield of nanofiber yarn could reach to a maximum of 4.207 g/h. The breaking strength and elongation at break of the prepared yarn could reach to 23.52 MPa and 30.61 %, respectively.  相似文献   

4.
Continuously twisted polyacrylonitrile/viscose nanofiber core-spun yarns were fabricated through novel self-designed multi-nozzle air jet electrospinning set-up. The effect of voltage, solution flow rate, air flow rate and funnel rotating speed on coating rate of core-spun yarn, nanofiber diameter, twist level and mechanical property were discussed. The results showed that polyacrylonitrile/viscose nanofiber core-spun yarns with perfect nanofiber orientation and uniform twist distribution could be obtained at voltage of 32 KV, solution flow rate of 32 ml/min and air flow rate of 1000 ml/min, and the spinning speed could reach to 235.5 cm/min. The diameters of outer coated nanofiber distributed from 100 nm to 300 nm, and nanofiber coating rate could reach to 70.4 %. In addition, the strength and elongation at break increased from 30.82 MPa to 69.65 MPa and from 28.34 % to 43.29 % at the twist angle of 46.6 °, respectively.  相似文献   

5.
In order to fabricate continuously twisted nanofiber yarns, double conjugate electrospinning had been developed using two pairs of oppositely charged electrospinning nozzles. The principle and process of this novel yarn spinning method were analyzed, and the effect of applied voltage, nozzle distance between positive and negative, solution flow rate and funnel rotating speed on the diameters, twist level and mechanical properties of resultant PAN nanofiber yarns were investigated in this paper. The results indicated that electrospun nanofibers aggregated stably and bundled continuously at the applied voltage of 18 kV, the nozzle distance of 17.5 cm between positive and negative, the overall flow rate of 3.2 ml/h and the flow ratio of 5/3 for positive and negative nozzles. The resultant nanofiber yarns had favorable orientation and uniform twist distribution, and the twist level of nanofiber yarns increased with the increase of the ratio of funnel rotating speed and winding speed. The diameters and mechanical properties of nanofiber yarns depended on their twist level. The diameters of prepared PAN nanofiber yarns ranged from 50 µm to 200 µm, and the strength and elongation of PAN nanofiber yarns at break were 55.70 MPa and 41.31%, respectively, at the twist angle of 41.8 °. This method can be also used to produce multifunctional composite yarns with two or more components.  相似文献   

6.
In view of the interest in wicking properties of these flexible structures, analysis of the wicking phenomena in nylon 6.6 nanofiber yarns is carried out by considering the twist rate effects. A novel method is used based on adding a pH-sensitive dye to yarn interstructure and the analysis of color alteration of nanofiber yarn structure, resulting from a shift in pH, during the capillary rise of distilled water. The results show that the addition of pH- sensitive dye has no influence on the average nanofiber diameter and the wicking behavior of yarns. This study shows that in short durations, the kinetic of the capillary rise follows the Lucas-Washburn equation. The Lambertw, a mathematical function, has been incorporated, which helps measure an equivalent structural factor of nanofiber yarns and vertical wicking height at any given time considering the gravitational effects. The statistical results show that the average of equilibrium wicking height and capillary rise rate coefficient tend to decrease with increasing the nanofiber yarn twist, due to the reduction of continuity and size of capillaries.  相似文献   

7.
Wet electrospinning is a simple and efficient method to manufacture continuous nanofiber filaments. However, polyacrylonitrile nanofiber filaments collected using a static water bath are limited for application in certain areas due to their low degree of alignment and breaking stress values. To improve these properties, a novel countercurrent flowing liquid bath collector was combined with a multi-needle electrospinning device. The morphologies, crystalline structures, thermal behaviors and mechanical properties of filaments fabricated under different countercurrent bath liquid motion conditions were investigated. In addition, the forces acting on the nanofibers in the bundling triangular zone under countercurrent liquid bath motion were analyzed. The results showed that the average nanofiber diameter of the filaments decreased with an increase in bath solution motion forces. The maximum alignment degree and breaking stress of the nanofibers were 85 % and 0.63 cN/dtex, respectively, achieved using a liquid flow rate of 80 ml/min and water inlet diameter of 6 mm. The alignment degree of the assembled nanofibers in the bundling triangular zone could be increased by 57 % when using a countercurrent flowing liquid compared with a static liquid bath.  相似文献   

8.
This study aims to develop a new approach for fabricating hollow nanofibrous yarns by engineering a triple-layer structure (polyvinyl alcohol (PVA) multifilament core surrounded by a layer of PVA nanofibers and a polylactic acid (PLA) nanofiber outer layer). After fabrication of this 3-layer structure, the core portion was extracted, leaving the outer layer intact after dissolving the PVA nanofibers in water. To determine the optimum thickness of the outer layer, hollow nanofiber yarns with five different thicknesses were produced. A hollow nanofiber yarn was also produced using a common method to enable comparison of the methods. In the common method, a core sheath yarn consisting of a PVA multifilament core and a PLA nanofiber outer layer was fabricated, and a hollow yarn was produced by placing the core yarn in hot water. The results revealed facilitation of core extraction from the yarn body of the new 3-layer structure, which occurred due to rapid dissolution of the middle layer. The wicking behavior in the hollow yarn fabricated using the novel method followed the Locus Washburn equation and that of the hollow yarn produced from the core sheath yarn deviated from it. The results demonstrated that tensile properties of hollow nanofiber yarns were improved by increasing the thickness. Furthermore, hemolysis and cytotoxicity assays indicated that the fabricated hollow nanofibrous structure is non-toxic and blood compatible, indicating its potential for use in biomedical applications such as vascular scaffolds.  相似文献   

9.
Electric field plays a key role in electrospinning process for nanofiber and nanofiber yarn producing. The electric field distribution of the yarn manufacturing system is simulated by using finite element method analysis. The effects of electric field distribution and intensity were studied to analyze the influence of the electric field on the electrospun nanofiber yarn surface morphology, mechanical, thermal and water absorption properties. The results show that the morphology and diameters of nanofiber and yarn were obviously affected by the electric field with changing the needle distance and applied voltage, which further influence the mechanical performance of the yarn. The needle distance does not much affect the thermal property of the PSA electrospun yarn, whereas the yarn obtains better thermal resistance properties at voltage of 25 kV. The nanoyarn electrospun and assembled under higher applied voltage is proved to have a better wicking property in our research.  相似文献   

10.
Polyacrylonitrile (PAN) nanofiber filaments were manufactured continuously for several hours by a homemade multi-needle electrospinning device. The yarns were continuously obtained by plying and twisting nanofiber filaments using a self-made twisting device. The structures and mechanical properties of yarns were investigated. The influences of twist setting temperatures and periods of time on morphology and mechanical properties were discussed. The results showed that the alignment degree of nanofibers along the filament axis could reach 70.9 %. The twist angle increased with increasing twists and the number of filaments. With increasing twists, the breaking stress and strain increased initially and then decreased; the maximum breaking stress and strain were 34.7 MPa and 26.1 %, respectively; the initial modulus decreased with increasing twists and plies, the maximum modulus was 391.3 MPa. Both the breaking stress and strain increased with the increase of twist setting temperatures and times. The optimal setting temperature and time were 90 °C and 30 min, respectively, the maximum breaking stress and strain were 32.8 MPa and 20.8 %, meanwhile, the crystallinity improved from 34.5 % to 39.9 %. This study demonstrates the possibility of continuously and stably manufacturing PAN nanofiber yarns.  相似文献   

11.
The aim of this paper is to investigate vertical wicking in polyacrylonitrile (PAN) electrospinning nanofiber yarn using image analysis. Colored liquid rising phenomenon into the yarn and the distance of liquid rise were determined as a function of time. The kinetics of capillary rise follows the Lucas-Washburn equation. The results show that capillary rise rate coefficient is being reduced with increasing yarn twist, due to the reduction of continuity and size of capillaries. Increasing heat treatment stretch from 0 % (draw ratio=1) to 50 % (draw ratio=1.5) increases the capillary rise rate coefficient, due to the more homogeneity of capillary spaces in the yarn structure and increasing heat treatment stretch from 50 to 100 % (draw ratio=2) reduces capillary rise rate coefficient, because of the low capillary length. The present study indicates that an appropriate choice in production parameters of nanofiber yarn is all important in obtaining the desired properties of capillary rise.  相似文献   

12.
In the present study, an attempt has been made to obtain the relationships for prediction of yarn diameter from different fibers and spinning technologies. The Peirce formula is found to give high deviation from the observed values of yarn diameter because it does not take the effect of twist, type of fibre and spinning technology into consideration. A new empirical model has been proposed that takes into account the parameters affecting the yarn diameter to a great extent, namely yarn twist, spinning technology and type of fibre in calculating the yarn diameter. The spinning technology, type of fibre and the proportion of fibre in the yarn have significant effect on yarn diameter. The proposed model is able to predict the yarn diameter more accurately.  相似文献   

13.
The effects of some yarn properties (i.e. type, count, twist level, ply number, unevenness and crimp) and fabric constructional properties (i.e. cover, thickness and balance) on surface roughness values of cotton woven fabrics were investigated. A general overview of the results showed that surface roughness values of fabrics were affected from yarn and fabric properties and the effects were related to fabric balance, fabric cover (not cover factor), fabric thickness and crimp values of yarns in fabric structures. Surface roughness values of fabrics decreased as yarn fineness and yarn twist levels increased but as yarn ply number decreased. Also, surface roughness values gradually decreased from open-end yarn constituting fabrics to combed yarn constituting fabrics. Results showed that different properties of yarns caused changes in yarn crimps in fabric structure and also governed the changes in fabric balance, as well as changes in roughness of fabric surfaces. The changing properties of yarns and impact of these properties on fabric construction affected the formation of cotton fabric surfaces from smooth to coarse.  相似文献   

14.
Well-aligned PMIA nanofiber mats were fabricated by electrospinning and then hot-stretching along the fiber axis was used to improve the mechanical properties of nanofibers in this paper. Scanning electron microscopy (SEM), X-ray diffraction (XRD) and Differential scanning calorimetry (DSC) were used to characterize the morphology and properties of nanofibers. The results showed that the nanofibers became thinner and better alignment than the as-spun nanofibers after hotstretching, and the average diameter of the nanofibers decreased with the increasing of the tensile force. In the same time, hotstretching improved the crystallinity and T g of the as-spun PMIA nanofibers. The tensile strength and modulus of the hotstretched nanofiber mats peaked at ca.50 % and ca.196 % respectively at the tensile force of 12 N compared with the as-spun nanofiber mats.  相似文献   

15.
Silk fibroin (SF) nanofibers were prepared by electrospinning and their application as an enzyme immobilization support was attempted. By varying the concentration of SF dope solution the diameter of SF nanofiber was controlled. The SF nanofiber web had high capacity of enzyme loading, which reached to 5.6 wt%. The activity of immobilizedα-chymotrypsin (CT) on SF nanofiber was 8 times higher than that on silk fiber and it increased as the fiber diameter decreased. Sample SF8 (ca. 205 nm fiber diameter) has excellent stability at 25°C by retaining more than 90 % of initial activity after 24 hours, while sample SF11 (ca. 320 nm fiber diameter) shows higher stability in ethanol, retaining more than 45% of initial activity. The formation of multipoint attachment between enzyme and support might increase the stability of enzyme. From these results, it is expected that the electrospun SF nanofibers can be used as an excellent support for enzyme immobilization.  相似文献   

16.
The development of a modified method to produce heat treated twisted nanofibrous yarns using two oppositely metallic spinnerets system is presented. This method allows the production of more uniform, stronger twisted poly acrylonitrile (PAN) yarns. The novelty of this system permits for in-situ heat treating of the nanofiber yarns. The average diameter of twisted nanofiber yarns is 340.65 μm with 5.8 CV%. The values of the initial modulus and stress of heat treated yarns increase from 1.90 GPa and 61.30 MPa in untreated one to 4.51 GPa and 116.56 MPa, respectively. In order to quantify the alignment of the nanofibers Fourier power spectrum (FPS) and image analysis were used. So the treated yarn shows more degree of nanofiber alignments than the untreated one.  相似文献   

17.
The current research discusses the efforts to achieve a Poly(lactide-co-glycolide)(PLGA) nanofiber yarn using two differently charged nozzles with potential application as surgery suture. First, electrospinning parameters such as solution concentration, applied voltage, feed rate were optimized to produce yarn with smooth nanofibers. In order to improve the properties of produced suture, heat setting setup was developed. Two heat setting techniques, including hot water and dry heat were applied, and the influence of the heat setting process on the mechanical properties of yarn was studied. The results showed that heat setting with boiling water was the best method. At first strength, E-modulus and extension of prepared suture were 36.6 MPa, 0.9 GPa and 68.8 % respectively. After improvement with heat setting, strength and E-modulus increased to 63.7 MPa, 2.7 GPa respectively and extension decreased to 29.7 %. Finally, in order to analyze knot performance, two types of surgical knot (square and surgeon) were used, and mechanical properties were investigated. The presence of knot lessens mechanical properties for each two type. Square knot showed better mechanical properties than surgeon’s knot. With square knot strength, E-modulus and extension were 62.1 MPa, 2.1 GPa, 28.6 %, respectively. In vitro study of nanofiber yarn degradation behavior showed that the mechanical properties were decreased. This could be due to greater surface area of nanofibers exposed to surrounding environment.  相似文献   

18.
The impact of fiber friction, yarn twist, and splicing air pressure on mechanical and structural properties of spliced portion have been reported in the present paper. The mechanical properties include the tensile and bending related properties and, in the structural properties, the diameter and packing density of the splices are studied. A three variable three level factorial design approach proposed by Box and Behnken has been used to design the experiment. The results indicate that there is a strong correlation between retained spliced strength (RSS) and retained splice elongation (RSE) with all the experimental variables. It has been observed that RSS increases with the increase in splice air pressure and after certain level it drops, whereas it consistently increases with the increase in yarn twist. The RSE increases with the increase in both fiber friction and yarn twist. It has also been observed that the yarn twist and splicing air pressure have significant influence on splice diameter, percent increase in diameter and retained packing coefficient, but the fiber friction has negligible influence on these parameters. Yarn twist and splicing air pressure has a strong correlation with splice flexural rigidity, where as poor correlation with retained flexural rigidity.  相似文献   

19.
A series of blend nanofiber mats comprising poly(vinyl alcohol) (PVA) and polyurethane (PU) were prepared by dual-jet electrospinning in various parameters. Orthogonal experimental design was used to investigate how those parameters affected on fiber diameters and fiber diameter distribution. Altogether three parameters having three levels each were chosen for this study. The chosen parameters were tip-to-collector distance (TCD), voltage and tip-to-tip distance (TTD). Fiber diameters, thermal properties, mechanical properties and hydrophilicity of the blend nanofiber mats were examined by scanning electron microscopy (SEM), thermogravimetric analysis (TGA), tensile test, contact angle and water absorption test, respectively. The results showed that the optimum conditions for PVA/PU blend nanofiber mats fabricated by dual-jet electrospinning were TCD of 20 cm, voltage of 18 kV and TTD of 4 cm. Besides, the thermal stability of PVA/PU blend nanofiber mats had been improved compared with pure nanofibers. Furthermore, the elongation and tensile strength of the blend nanofiber mats were significantly increased compared with pure PVA and pure PU, respectively. And the blend nanofiber mats exhibited well hydrophilicity.  相似文献   

20.
In the paper, one kind of super draft ring spinning frame with four drafting rollers and corresponding three drafting zones were introduced. The yarn qualities spun by the super draft ring spinning frame were analyzed by studying the shape of spinning triangles. Using the high speed camera system OLYMPUS i-speed3 and one kind of transparent front top roller, the spinning triangles were captured, and the geometry size of spinning triangle were measured. Then, according to the theoretical model of fiber tension in the spinning triangle, fiber tension distributions in the spinning triangles were presented by using Matlab software. Using the combed roving of 350 tex as raw material, three kinds of cotton yarns, 27.8 tex (21S), 18.2 tex (32S) and 14.6 tex (40S), were spun in the common ring spinning frame with three different suitable spindle speeds, travelers and twist factors. Using the combed roving of 350 tex and 500 tex as raw material, 14.6 tex cotton yarns were spun in the super draft ring spinning frame with three different drafting ratios at back zone. It is shown that with the increasing of spindle speed, a more asymmetric shape of spinning triangle would be produced, and lead to worsen yarn evenness. With the decreasing of traveler weight, the height and horizontal deviation of the spinning triangle is decreased, and may lead to better yarn evenness and less long hairiness. By taking suitable large yarn twist factors, the comprehensive qualities can be improved. Comparing with the common ring spinning, the spinning triangle is larger in the super draft ring spinning. That is, in the super draft ring spinning, the fibers in the strand in the front roller nip are more dispersed, and not benefit for yarn qualities. Therefore, the compact device was introduced into the super draft ring spinning, and the cotton pure yarns and blend yarns were spun, and the yarn qualities were measured and analyzed.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号