首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 46 毫秒
1.
Abstract

Untreated Scots pine (Pinus sylvestris) and Norway spruce (Picea abies) samples were exposed above ground in a durability test for 6 years. The samples consisted of three pieces of wood, 22×95×500 mm, screwed together; two pieces lengthwise with a third piece overlapping. Weight was measured, to calculate moisture content (MC), and samples checked regularly for cracks and fungal growth. Parameters investigated were heartwood/sapwood (pine), annual ring orientation (spruce), stand site, annual ring width and density. Stand site, annual ring width and density had no influence on MC or fungal growth for either pine or spruce. Spruce samples with vertical annual rings had fewer cracks than samples with horizontal annual rings. Pine sapwood samples had a high MC and a large amount of rot fungi, while heartwood had a lower MC and no rot. Most spruce samples were similar to pine heartwood, except from a few samples that had high MC and fungal growth. Those were all sawn from the outer part of the log. Therefore, it can be stated that spruce sawn from the inner part has almost the same properties as pine heartwood, while spruce from the outer part of the log has similar properties to pine sapwood.  相似文献   

2.
Abstract

Wood is susceptible to decay by rot fungi if it is exposed to high-moisture contents during long periods of time and it is therefore important to limit the duration of such periods. Critical points in outdoor wood structures are, for example, end grain surfaces in joints where water can get trapped after a rain. It is therefore of interest to study both absorption and redistribution of moisture in wood. This paper presents moisture content profiles during end grain water absorption and redistribution in Norway spruce (Picea abies (L.) Karst.) measured by computed tomography with the specimens in individual climate boxes. Heartwood and sapwood of two provenances (slow-grown and fast-grown wood) were included. No major differences were seen between the water uptake of the slow-grown and the fast-grown wood since the densities were similar despite of the large difference in growth ring width. However, for the sapwood specimens, the moisture content was higher further into the specimens than for the heartwood specimens in agreement with previous studies. For the slow-grown wood, the redistribution was also generally more rapid for the sapwood specimens than for the heartwood specimens.  相似文献   

3.
Abstract

Thermal modification has been developed for an industrial method to increase the biological durability and dimensional stability of wood. In this study the effects of thermal modification on resistance against soft- and brown-rot fungi of sapwood and heartwood of Scots pine and Norway spruce were investigated using laboratory test methods. Natural durability against soft-rot microfungi was determined according to CEN/TS 15083-2 (2005) by measuring the mass loss and modulus of elasticity (MOE) loss after an incubation period of 32 weeks. An agar block test was used to determine the resistance to two brown-rot fungi using two exposure periods. In particular, the effect of the temperature of the thermal modification was studied, and the results were compared with results from untreated pine and spruce samples. The decay resistance of reference untreated wood species (Siberian larch, bangkirai, merbau and western red cedar) was also studied in the soft-rot test. On average, the soft-rot and brown-rot tests gave quite similar results. In general, the untreated heartwood of pine was more resistant to decay than the sapwood of pine and the sapwood and heartwood of spruce. Thermal modification increased the biological durability of all samples. The effect of thermal modification seemed to be most effective within pine heartwood. However, very high thermal modification temperature over 230°C was needed to reach resistance against decay comparable with the durability classes of “durable” or “very durable” in the soft-rot test. The brown-rot test gave slightly better durability classes than the soft-rot test. The most durable untreated wood species was merbau, the durability of which could be evaluated as equal to the durability class “moderately durable”.  相似文献   

4.
In the present study, durability of untreated and thermally modified sapwood and heartwood of Scots pine and Norway spruce was examined using a modified double layer test. Base layer samples were partly on contact with ground where exposure conditions were harder than that in a double layer test above the ground. The base layer on ground contact gave results already after one year of exposure in Finnish climate, but the top layer of a double layer test element simulated more the situation of decking exposure.

Significant differences in durability and moisture content (MC) between the wood materials were detected after six years of exposure in the field. Thermally modified pine heartwood performed very well in all layers of the test element and only minor signs of decay were found in some of the base samples. Both sapwood and heartwood of thermally modified spruce were suffering only slight amounts of decay while thermally modified pine sapwood was slightly or moderately decayed. Untreated sapwood samples of pine and spruce were severely decayed or reached failure rating after six years in the field. Untreated heartwood samples performed clearly better. The highest MCs were measured from untreated and thermally modified pine samples. Thermal modification increased significantly the durability and decreased the MC values of all wood materials.  相似文献   

5.
Scots pine (Pinus sylvestris) sapwood was investigated for variation in treatability using the wood modifying agent, furfuryl alcohol (FA) in water. The variation in treatability within trees, between trees and between different stands of Scots pine was studied. Investigated variables that reduced the residual variance significantly were: site location, latitude of site, height of trees, annual ring width, vertical and horizontal position in the tree and method of drying. Linear mixed model statistics were used and tree number was handled as a random variable. The best model reduced the treatability residual variance by 67%. Location was the single factor affecting treatability most. Differences in latitude between locations may be the reason for that. Latitude correlated negatively with the treatability. Within the trees, the treatability of sapwood increased with distance from ground and with distance from heartwood border. A small, but significantly better treatability was found for kiln dried wood (60°C) compared to air dried wood (20°C).  相似文献   

6.
This study focused on the distribution of wood components along a cross section of a spruce stem. Thin samples of earlywood and latewood were analysed by special micro-scale analytical techniques. Heartwood contained significantly more lignin and less cellulose than sapwood. The total content of hemicelluloses was the same along the radial direction, but the distribution of sugar units differed. The amounts of arabinoglucuronoxylan and pectins were larger in the heartwood. The transition zone between heartwood and sapwood had a specific composition, with less lignin and lipophilic extractives than heartwood and sapwood. For earlywood and latewood, significant differences were found in the distribution of sugar units in hemicelluloses. Latewood contained clearly more galactoglucomannan than earlywood, and conversely less pectins. The lipophilic extractives were also less concentrated in the latewood.Abbreviations EW or E earlywood - LW or L latewood - HW heartwood - SW sapwood - TZ transition zone wood - A.R. annual ring - AcBr Acetyl bromide - Ara arabinose - Xyl xylose - Gal galactose - Glc glucose - Man mannose - Rha rhamnose - GlcA glucuronic acid - MGlcA 4-O-methyl-glucuronic acid - GalA galacturonic acid - o.d. oven dry  相似文献   

7.
Water soluble polysaccharides from Norway spruce, Scots pine, and Siberian larch were compared. For all species the total amount of polysaccharides isolated from the heartwood was higher than that from the sapwood. The heartwood polysaccharides had a high content of galactose and arabinose units, and some glucuronic acid units, suggesting the presence of acidic arabinogalactans. The total amounts of recovered water-soluble arabinogalactans were 1.9 mg/g for spruce heartwood, 5.3 mg/g for pine heartwood, and as much as 106 mg/g for larch heartwood. The other water-soluble polysaccharides were mainly glucomannans. The average ratio of Gal:Ara:GlcA in the water-soluble arabinogalactans of spruce heartwood was about 4.3:1:1, pine heartwood about 4.5:1:0.2, and larch heartwood about 6.7:1:0.1. The corresponding molar ratios then being about 3.6:1:0.8 for spruce, 3.8:1:0.2 for pine, and 5.6:1:0.08 for larch. Thus, the content of glucuronic acid units was especially high in the spruce heartwood arabinogalactans. The content of arabinose was slightly higher in spruce and pine than in larch heartwood arabinogalactans.  相似文献   

8.
Norway spruce [Picea abies (L.) Karst.] heartwood and sapwood have differing wood properties, but are similar in appearance. An investigation was made to see whether near-infrared spectroscopy (NIRS) could be used with multivariate statistics for separation between heartwood and sapwood in dry state on tangential longitudinal surfaces. For classification of wood into sapwood and heartwood, partial least square (PLS) regression was used. Orthogonal signal correction (OSC) filtering was used on the spectra. This study shows that a separation of sapwood and heartwood of spruce is possible with NIR spectra measured in a laboratory environment. The visible-wavelength spectra have significant influence on the predictive power of separation models between sapwood and heartwood of spruce. All 44 specimens in the calibration set were correctly classified into heartwood and sapwood. Validation of the model was done with a prediction set of 16 specimens, of which one was classified incorrectly.  相似文献   

9.
Abstract

Uncoated Norway spruce specimens from different spatial positions within stems from two origins with different growth conditions were exposed to liquid water over a prolonged time, and apparent diffusion coefficients and rates of void filling were calculated from sorption curves. Both apparent diffusion and rate of void filling were significantly affected by origin and by the difference between inner and outer boards. The differences between inner and outer boards were explained by heartwood proportion and density, but some effects of origin remained when these properties were accounted for. The apparent diffusion coefficient was reduced by increasing density, and increased by increasing heartwood proportion. Void filling rate was reduced by both increasing density and increasing heartwood proportion. Since the effect of heartwood proportion was more pronounced in the material from the highly productive area, it may have been confounded with properties of juvenile wood.  相似文献   

10.
Summary This study compared the susceptibility of five UK‐grown conifer species to colonization by sapstain fungi in two trials carried out in consecutive years. The conifers consisted of Sitka spruce (Picea sitchensis), Japanese larch (Larix kaempferi), Norway spruce (Picea abies), Scots pine (Pinus sylvestris) and lodgepole pine (Pinus contorta). Freshly cut 1‐m logs were exposed to the available inoculum of sapstain fungi from April to August in a woodland environment in the south east of England. Logs of each species were removed after 1‐, 2‐ and 4‐month exposure and sampled destructively to assess the amount of sapstain. In the second trial, per cent moisture content and concentrations of nitrogen, carbohydrate and phenolic compounds in the sapwood were also measured at the start and end of the trial. After 2 months, only the sapwood of both pine species had significant levels of sapstain; mean values of 37% and 19% for lodgepole pine (year 1 and year 2 respectively) and 12% and 1% for Scots pine. After 4 months, the levels of sapstain in both pine species exceeded 60% in both years. By contrast, very little sapstain developed in the other conifer species with maximum mean values of 10% for Norway spruce, 3.5% for larch and less than 1% for Sitka spruce. Overall, the moisture content of the logs decreased progressively in all species over the length of the trial. However, pine logs tended to retain higher levels of moisture throughout the trial compared with spruce or larch. The relatively higher moisture content of pine sapwood may be closer to the optimal moisture content that sapstain fungi require for infection and colonization, thereby contributing to the increased susceptibility of pine compared with the other conifer species. The pine logs also suffered from some colonization by bark beetles (Ips sexdentatus), which increased the inoculum potential and the opportunity for colonization by sapstain fungi. In addition, particular phenolic compounds in conifer sapwood may play a role in determining the resistance of some species to sapstain. Notably the most resistant species, Sitka spruce, was the only softwood that still retained detectable levels of phenolics in the sapwood to the end of the trial.  相似文献   

11.

To study and model the variation of wood properties, sample trees were selected from 42 Norway spruce and 20 Scots pine stands covering a wide variation in climatic and site conditions, stand maturation and tree sizes. Plot and tree measurements were followed by sampling wood from different heights in each sample tree and laboratory measurements of wood properties. Mixed linear and non-linear prediction models were developed using diameters, number of annual rings and climatic indices as explanatory variables. The variation in spruce properties explained by these variables was: basic density 50%, latewood content 52%, juvenile wood diameter 85%, heartwood diameter 94% and bark thickness 76%. The corresponding values for pine were 59, 54, 79, 92 and 85%. Random among-tree variance was an important contributor to the remaining variation for density and latewood. In general, only a minor part of the random variation was related to variance between stands. Predictions derived from the models for density and juvenile wood in both species, and heartwood in pine showed good agreement when validated with data sets from two other studies. The resulting models may be used for predicting wood properties in forest planning and in bucking computers in harvesters, provided that the essential information is available.  相似文献   

12.
Wood from Norway spruce (Picea abies L. Karst.) is biologicallydegraded in exposed conditions. It also has anatomical featuresthat make it difficult to impregnate with preservatives by currentlyavailable industrial processes. In the study reported here,we used the new Linotech process to impregnate Norway sprucewood with hydrophobic linseed oil and then quantified its uptakeand dispersal in anatomically distinct wood tissues. We alsoinvestigated the effects of the wood moisture content on theresults of the impregnation. Samples (500 x 25 x 25 mm) weretaken from 15 trees in a coniferous forest in northern Sweden(64° 10' N, 160–320 m a.s.l.). The parameters forthe Linotech process were 2–3 h treatment time at 0.8–1.4MPa and 60–140°C. To determine the level of uptake,the linseed oil was extracted from the impregnated wood usingmethyl-tertiary-butyl-ether. The uptake was quantitatively analysedby comparing X-ray microdensitometry values obtained followingimpregnation both before and after oil removal. In earlywood,initial moisture content had an obvious effect on the impregnationresult. Six times more oil was taken up when the moisture contentwas greater than ~150 per cent than when it was less than 30per cent. Theoretical calculations, based on density levels,suggest that the water-filled porosity of the wood (water volumedivided by porosity volume) was positively correlated with thelinseed oil uptake, and more strongly correlated in earlywoodthan in latewood. There were also significant differences inuptake between different wood tissues; heartwood/mature woodand heartwood/juvenile wood showed 10–20 per cent weightincreases due to linseed oil uptake, compared with 30–50per cent in sapwood/mature wood. Examination by scanning electronmicroscopy confirmed these uptake patterns. The moisture contentafter impregnation was about 5 per cent, irrespective of theLinotech process parameters, tissue type and initial moisturecontent. In conclusion, the impregnation process used here resultsin high levels of well-dispersed linseed oil uptake and shouldfacilitate drying.  相似文献   

13.
Dissolution and dispersion of spruce wood components into hot water   总被引：1，自引：0，他引：1  
Summary The dissolution and dispersion of components from Norway spruce (Picea abies) wood were examined in laboratory experiments to determine the factors influencing variations in dissolved and colloidal substances in mechanical pulp suspensions. Finely ground, fresh spruce wood was suspended in water at 90 °C and was agitated intensively for up to 12 h, after which the concentrations of dissolved and dispersed lipophilic extractives, lignans, carbohydrates and lignins were determined. Sapwood and heartwood were studied separately. Effects of pH and added electrolytes on the dissolution and dispersion of wood components were also investigated.Higher amounts of lipophilic extractives, and especially of triglycerides, were dispersed from sapwood than from heartwood. The release of lipophilic extractives continued for up to 3 h, after which the concentrations in the suspensions leveled off. At this stage the composition of the dissolved and dispersed lipophilic extractives equaled that of the wood. The amount of lipophilic extractives in the suspensions increased with increased pH, in the range of 4.5–6.7, but was lower in the presence of electrolytes. The dissolution of carbohydrates continued even beyond 3 h of agitation. The high water temperature induced hydrolytic reactions, thereby releasing especially arabinose. The release of arabinose through the hydrolytic cleavage from polysaccharides was more extensive at pH 4.5 than at pH 5.5 and 6.7. More polysaccharides containing galacturonic acid units (pectins) were dissolved at a higher pH. Much more polysaccharides containing glucose, most probably starch, were present in the sapwood suspensions. The dissolution of lignins also continued throughout the 12 h experiment. The measured UV-absorption, after extraction of lignans, was roughly the same for sapwood and heartwood suspensions. Slightly less lignins were released in the presence of electrolytes. Lignans were released only from heartwood.  相似文献   

14.
In order to perform service life predictions of rain exposed wood structures, the moisture and temperature conditions in the structure need to be known as well as which degradation that occurs under those exposure conditions. The microclimate (the moisture conditions at the surface) is the boundary condition for moisture transport into the wood and depends on the detail design; joints between two pieces of wood can act as a water trap which give long durations of surface moisture after rain events and hinders drying. This study presents moisture content and microclimate measurements in three types of Norway spruce joints exposed to artificial rain in the laboratory. Both the microclimate (the duration of water on surfaces and in gaps) and the moisture content profiles were monitored. The microclimate was changed by changing the size of the gap between the two boards. The duration of water in the gap depended both on the gap size and on the permeability of the wood (sapwood/heartwood, end grain surface/side grain surface). In many cases, a larger gap width gave shorter durations of high moisture contents since a larger gap gave more favourable drying conditions, but the magnitude of this reduction varied between joint types.  相似文献   

15.
The variation in the basic‐density level of 45 stems of Sitka spruce from two Danish sites has been examined. It is shown that the basic‐density level, i.e. the basic density as a function of ring width, within the juvenile wood decreases with (1) increasing distance from the pith and (2) increasing height in the stem (same ring number from pith provided). Furthermore, the basic‐density level seems to decrease with increasing stand quality, which may affect the pattern of variation in basic‐density level if the stand quality class varies with age. The basic density of the juvenile wood is markedly higher in Sitka spruce than in Norway spruce, whereby the risk of stem cracks probably is reduced.  相似文献   

16.
Radiata pine sapwood and heartwood were dried using high-temperature, conventional-temperature, and air drying schedules with and without pre-steaming. They were then impregnated by vacuum treatment with double-distilled water, toluidine blue, and fluorescein dye. For sapwood, there were only minor differences in uptake between drying methods and when pre-steaming was used. Using microscopy, the primary flow pathways in sapwood were found to be the resin canal network and ray parenchyma cells, which provided conduction without large resistance. In heartwood, uptake was strongly influenced by pre-steaming the green lumber. After pre-steaming heart-wood, there was an increase in uptake from all surfaces but especially from the radial surfaces. Lower extractive contents, disruption of epithelial and ray parenchyma cells, and alteration of the condition of bordered pits were also associated with pre-steaming. It was therefore possible to classify flow paths in radiata pine heartwood five ways, according to uptake values and wood anatomical features.This research was presented in part at the 48th annual meeting of the Japan Wood Research Society, Shizuoka, April 1998.  相似文献   

17.
Liquid flow in dried wood is complicated to study, since wood is a nonhomogeneous, hygroscopic-porous, anisotropic material. However, liquid flow is important to understand, since it has an influence on the durability of wood and on such processes like impregnation, drying, surface treatment, etc. In this study, simulations of liquid water absorption in wood as a fibre network, percolation, were compared with experimental water absorption in the longitudinal direction in spruce timber. With CT scanning, water distribution during liquid flow can be shown visually and measured by image processing. Liquid water absorption in end grain of spruce was measured with CT scanning after 1, 3, 7 and 14?days of liquid water absorption and shown as moisture content (MC) profiles in heartwood and sapwood. It was found that the amount of water absorbed could be expressed as a linear function of the square root of time. The slopes of the lines differed between sapwood and heartwood and also varied depending on the growth condition of the trees. The simulations according to the percolation method show generally good agreement with the measured results for sapwood.  相似文献   

18.
Summary Two new proton magnetic resonance techniques, relaxation spectra and relaxation selective imaging, have been used to investigate the distribution of water in samples of normal white spruce sapwood, heartwood, and juvenile wood as well as two rehydrated heartwood samples containing incipient decay and compression wood respectively. It is demonstrated that the spin-spin (T2) relaxation behavior in wood is best presented as a continuous spectrum of relaxation times. Spectra of T2 for white spruce show separate peaks corresponding to the different water environments. Bound water gives a peak with an T2 time of about 1 ms and lumen water gives a distribution of T2 times in the range of 10 to 100 ms. The lumen water T2 time is a function of the wood cell radius. Consequently, the different cell lumen radii distributions for spruce sapwood, juvenile wood, and compression wood are readily distinguishable by the shape of their T2 spectra. Water environments which are separable on a T2 spectrum may be imaged separately. Imaging has been carried out in one dimension for bound water and lumen water of a spruce sapwood sample at four different moisture contents ranging from 100% to 17%. For the first time, we demonstrate that above the fibre saturation point the moisture density profile of the bound water is largely independent of moisture content. The feasibility and utility of using these techniques for internal scanning of logs and lumber is discussed. These techniques should provide new insights into the wood drying process.We would like to thank Michael Weiss of the Biological Science Electron Microscopy Facility at the University of British Columbia for his assistance with the microscopy and image analysis. This research was supported by grants from the Natural Sciences and Engineering Research Council of Canada and the Canadian Forestry Service  相似文献   

19.
Abstract

This study focused on the amount of sapwood and its variation by means of computed tomographic (CT) imaging. Twenty-four trees were selected from four Norway spruce [Picea abies (L.) Karst.] stands in north-eastern France, varying in age, density and fertility. In each stand, sampled trees represented the dominant, co-dominant and suppressed strata. The heartwood/sapwood boundary was detected from the CT images, and the heartwood and sapwood amount and their variations were then evaluated. At the within-tree level sapwood width was relatively constant along the tree stem above the butt swelling and below the living crown. The between-tree sapwood width variations were partially explained by the total cross-sectional area of living branches. This result opens up the possibility of investigating within-tree allometric relationships. Sapwood width was found to be highly correlated with tree slendemess (tree height/breast height diameter) and with the relative height of the crown. This suggests that sapwood width could be readily predicted from conventional forest inventory measurements. The number of sapwood rings within the stem was largely dependent on cambial age, and could be determined dynamically using the concept of mean lifetime of sapwood rings.  相似文献   

20.
Abstract

Thermal modification at elevated temperatures changes the chemical, biological and physical properties of wood. In this study, the effects of the level of thermal modification and the decay exposure (natural durability against soft-rot microfungi) on the modulus of elasticity (MOE) and modulus of rupture (MOR) of the sapwood and heartwood of Scots pine and Norway spruce were investigated with a static bending test using a central loading method in accordance with EN 408 (1995). The results were compared with four reference wood species: Siberian larch, bangkirai, merbau and western red cedar. In general, both the thermal modification and the decay exposure decreased the strength properties. On average, the higher the thermal modification temperature, the more MOE and MOR decreased with unexposed samples and increased with decayed samples, compared with the unmodified reference samples. The strength of bangkirai was least reduced in the group of the reference wood species. On average, untreated wood material will be stronger than thermally modified wood material until wood is exposed to decaying fungi. Thermal modification at high temperatures over 210°C very effectively prevents wood from decay; however, strength properties are then affected by thermal modification itself.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号