首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 595 毫秒
1.
This study was conducted to investigate the production of balanced diets for juvenile yellow perch (Perca flavescens) feeds. Six isocaloric (≈3.21 kcal/g), isonitrogenous (30.1 ± 0.4% db) ingredient blends were formulated with 0, 10, 20, 30, 40, and 50% distillers dried grains with solubles (DDGS), and appropriate amounts of soybean meal, fish meal, vitamins, and minerals. Extrusion cooking was performed using a laboratory‐scale single‐screw extruder at a constant barrel temperature profile of 40–90–100°C, and a constant screw speed of 230 rpm (24.1 rad/sec). The mass flow rate was determined during processing; it generally increased with progressively higher DDGS content. Additionally, moisture content, water activity, unit density, expansion ratio, compressive strength, compressive modulus, pellet durability index, water stability, and color were extensively analyzed to quantify the effects of DDGS content on the physical properties of the resulting extrudates. Significant differences (P < 0.05) between blends were observed for color and water activity for both the raw material and extrudates, respectively, and for the unit density of the extrudates. There were significant changes in brightness (L), redness (a), and yellowness (b) among the final products when increasing the DDGS content of the blends. Expansion ratio and compressive strength of the extrudates were low. On the other hand, all blends showed high pellet durability (PDI ≥ 96.18%). Overall, it was ascertained that DDGS could be successfully included at rates of <50%, and that each of the ingredient blends resulted in viable, high quality extrudates.  相似文献   

2.
A twin‐screw extrusion study was performed in replicated trials to produce vegetable‐based feeds for juvenile yellow perch. Two isocaloric (3.06 kcal/g) experimental diets were balanced to contain 20 and 40% distillers dried grains with solubles (DDGS) and a constant amount (20%) of fermented high‐protein soybean meal (PepSoyGen) as the fishmeal protein replacers; crude protein content was targeted at 40%. A fishmeal‐based diet was used as a control. Extrusion conditions included conditioner steam (0.11–0.16 kg/min), extruder water (0.11–0.19 kg/min), and screw speed (230–300 rpm). Increasing DDGS from 0 to 40% led to a considerable rise in bulk density, lightness L*), yellowness (b*), and unit density but to decreases in water activity (aw) and expansion ratio by 12.6, 14.4, 23, 21, 31, and 13%, respectively. The lowest unit density of 791.6 kg/m3 and highest bulk density of 654.5 kg/m3 were achieved with diets containing 20 and 40% DDGS, respectively; changes in DDGS content did not affect extrudate moisture, absorption index, or thermal properties. Raising DDGS from 0 to 40% resulted in an increase in water solubility and redness (a*) by 13.4 and 35%, respectively. All extrudates had high durability (>98%), and low aw of less than 0.5. Overall, this study yielded viable feeds for yellow perch.  相似文献   

3.
Corn distillers dried grains (DDGS) were compacted into cylindrical pellets (3.5 cm in length, 1.5 cm in diameter) utilizing a closed‐end die under axial stress from a vertical piston applied by an Instron universal testing machine. The effects of independent variables, including the raw material moisture content (25–35% db), processing temperature (100–120°C), pressure (12.5–37.5 MPa), and dwell time (5–15 sec) on pellet density, durability, and stability were determined using response surface methodology. Moisture content, temperature, and pressure significantly affected (P < 0.05) the properties of DDGS pellets, while the influence of dwell time was negligible (P > 0.05). Increasing temperature initially increased and then decreased unit density. High moisture and pressure had favorable effects on unit density and durability rating. The density ratio increased with increasing pressure and moisture content. The results suggested technical feasibility of compacting DDGS. For the range of variables tested, optimum levels were identified as 34.6% moisture content, 107°C press temperature, and 36.8 MPa pressure to obtain maximum durability and density and acceptable dimensional stability.  相似文献   

4.
Recently, the Elusieve process, a combination of elutriation (air classification) and sieving (screening) was developed to separate fiber from distillers dried grains with solubles (DDGS) to increase DDGS utilization in nonruminant (poultry and swine) diets. Elusieve process produces three products: 1) Pan DDGS, with 5% higher protein content than conventional DDGS, which would be used at higher inclusion levels in broiler diets because of low fiber content; 2) Big DDGS, with nearly the same protein content as conventional DDGS, which would be used at same inclusion levels as conventional DDGS; and 3) Fiber product. The objective of this study was to determine and compare pellet‐mill throughput, power consumption, and pellet quality for broiler diets incorporating different levels (0, 10, and 20%) of conventional DDGS and DDGS products from Elusieve process. Poultry oil contents were lower (1.5–1.6%) in diets comprising Pan DDGS and diets without DDGS than in the other diets (2.2–3.1%). The feed throughput was not affected by inclusion levels or type of DDGS. Pellet quality (pellet durability index [PDI]) for diets comprising Pan DDGS (both 10 and 20% inclusion levels) was significantly better than PDI for diets comprising conventional DDGS, Big DDGS, and the diet without DDGS. Better pellet quality of diets comprising Pan DDGS could be due to lower quantity of poultry oil used as well as compositional characteristics such as low fiber and high protein. Diets with Big DDGS had similar pelleting characteristics to those with conventional DDGS. Pellet quality deteriorated at higher inclusion levels of conventional DDGS, Big DDGS, and Enhanced DDGS. Considering that Pan DDGS would be included at higher inclusion levels in broiler diets, superior pellet quality of diets comprising Pan DDGS is beneficial.  相似文献   

5.
Three isocaloric (3.5 kcal/g) ingredient blends containing 20, 30, and 40% (wb) distillers dried grains with solubles (DDGS) along with soy flour, corn flour, fish meal, and mineral and vitamin mix, with net protein adjusted to 28% (wb) for all blends, were extruded in a single‐screw laboratory‐scale extruder at screw speeds of 100, 130, and 160 rpm, and 15, 20, and 25% (wb) moisture content. Increasing DDGS content from 20 to 40% resulted in a 37.1, 3.1, and 8.4% decrease in extrudate durability, specific gravity, and porosity, respectively, but a 7.5% increase in bulk density. Increasing screw speed from 100 to 160 rpm resulted in a 20.3 and 8.8% increase in durability and porosity, respectively, but a 12.9% decrease in bulk density. On the other hand, increasing the moisture content from 15 to 25% (wb) resulted in a 28.2% increase in durability, but an 8.3 and 8.5% decrease in specific gravity and porosity, respectively. Furthermore, increasing the screw speed and moisture content of the blends, respectively, resulted in an increase of 29.9 and 16.6% in extruder throughput. The extrudates containing 40% DDGS had 8.7% lower brightness, as well as 20.9 and 16.9% higher redness and yellowness, compared with the extrudates containing only 20% DDGS. Increasing the DDGS content from 20 to 40% resulted in a 52.9 and 51.4% increase in fiber and fat content, respectively, and a 7.2% decrease in nitrogen free extract. As demonstrated in this study, ingredient moisture content and screw speed are critical considerations when producing extrudates with ingredient blends containing DDGS, as they are with any other ingredients.  相似文献   

6.
Corn distillers' dried grains with solubles (DDGS) was extruded with corn meal in a pilot plant single‐screw extruder at different extruder die temperatures (100, 120, and 150°C), levels of DDGS (0, 10, 20, and 30%) and initial moisture contents (11, 15, and 20% wb). In general, there was a decrease in water absorption index (WAI), water solubility index (WSI), radial expansion, and L* value with an increase in DDGS level, whereas a* value and bulk density increased. Increase in extruder die temperature resulted in an increase in WSI and WAI but a decrease in L* and bulk density. Peak load was highest at 30% DDGS as compared with 0, 10, and 20% DDGS extrudates. Die temperature of 120°C and initial moisture content of 20% resulted in least peak load. The a* value remained unaffected by changes in extruder die temperature. Radial expansion was highest at extruder die temperature of 120°C. Maximum WAI, WSI, radial expansion, and L* value were obtained at 15% initial moisture content. An increase in initial moisture content, in general, decreased L* value and bulk density but increased a* value of extrudates.  相似文献   

7.
This study was conducted to develop a ready‐to‐eat extruded food using a single‐screw laboratory extruder. Blends of Indian barley and rice were used as the ingredients for extrusion. The effect of extrusion variables and barley‐to‐rice ratio on properties like expansion ratio, bulk density, water absorption index, hardness, β‐glucan, L*, a*, b* values, and pasting characteristics of extruded products were studied. A central composite rotatable design was used to evaluate the effects of operating variables: die temperature (150–200°C), initial feed moisture content (20–40%), screw speed (90–110 rpm), and barley flour (10–30%) on properties like expansion ratio, bulk density, water absorption index (WAI), hardness, β‐glucan, L*, a*, b* values, and sensory and pasting characteristics of extruded products. Die temperature >175°C and feed moisture <30% resulted in a steep increase in expansion ratio and a decrease in bulk density. Barley flour content of 10% and feed moisture content of <20% resulted in an increased hardness value. When barley flour content was 30–40% and feed moisture content was <20%, a steep increase in the WAI was noticed. Viscosity values of extruded products were far less than those of corresponding unprocessed counterparts as evaluated. Rapid visco analysis indicated that the extruded blend starches were partially pregelatinized as a result of the extrusion process. Sensory scores indicated that barley flour content at 20%, feed moisture content at 30%, and die temperature at 175°C resulted in an acceptable product. The prepared product was roasted in oil using a particular spice mix and its sensory and nutritional properties were studied.  相似文献   

8.
The goal of this study was to investigate the effect of die nozzle dimensions, barrel temperature profile, and moisture content on DDGS-based extrudate properties and extruder processing parameters. An ingredient blend containing 40% distillers dried grains with solubles (DDGS), along with soy flour, corn flour, fish meal, whey, mineral and vitamin mix, with a net protein content adjusted to 28% was extruded in a single-screw laboratory extruder using seven different die nozzles. Increasing moisture content of the ingredient mix from 15 to 25% resulted in a 2.0, 16.0, 16.3, 22.9, 18.5, 32.5, and 63.7% decrease, respectively, in bulk density, water-solubility index, sinking velocity, L*, b*, mass flow rate, and absolute pressure, as well as 11.6, 16.2, and 7% increases, respectively, in pellet durability, water-absorption index, and a*. Increasing the temperature from 100 to 140°C resulted in 17.0, 5.9, 35.4, 50.6, 28.8, 33.9, and 33.9% decreases, respectively, in unit density, pellet durability, sinking velocity, absolute pressure, specific mechanical energy, torque, and apparent viscosity, but a 49.1 and 16.9% increase, respectively, in dough temperature and water-absorption index. Increasing the L/D ratio of the die nozzle resulted in an increase in bulk density, L*, a*, and torque, but a decrease in unit density, pellet durability, water-absorption index, sinking velocity, b*, mass flow rate, dough temperature, and apparent viscosity. As demonstrated in this study, the selection of an appropriate die geometry, in addition to the selection of suitable temperature and moisture content levels, are critical for producing DDGS-based extrudates with optimum properties.  相似文献   

9.
Distillers dried grains with solubles (DDGS) is a bulk material that has been widely used as a protein source for ruminants and nonruminants for more than two decades. DDGS is the nonfermentable processing residue (i.e., protein, fiber, fat, and ash) from fuel ethanol manufacturing. With the exponential growth of the fuel ethanol industry in the past several years, significant quantities (≈13.0 million tons in 2007) of distillers grains are now being produced. To effectively utilize these coproduct streams in the domestic market, DDGS must be transported greater distances and must be stored until final use. DDGS flow is often problematic as it can become restricted by caking and bridging that occur during shipping and storage. This flowability problem can present itself during dynamic and static flow conditions. This issue most likely results from physical or chemical interactions between particles (including particle size and shape), storage moisture, temperature, and relative humidity variations, as well as storage time. The objective of this study was to examine the effect of five moisture content levels (10, 15, 20, 25, and 30% db) on the resulting physical and chemical properties of DDGS with four soluble levels (10, 15, 20, and 25% db). To produce these materials, condensed distillers solubles (CDS) were combined with DDG, and appropriate quantities of water were added to adjust moisture contents. Carr indices were used to quantify the flowability of the DDGS samples. The results showed that both soluble level and moisture content had noticeable effects on physical and flow properties (e.g., aerated bulk density, packed bulk density, and compressibility). According to dispersibility, flowability index, and floodability index, flowability generally declined significantly (P < 0.05) with an increase in moisture content for most of the soluble levels under consideration. The color values and protein content of the DDGS were significantly affected (P < 0.05) as soluble level increased as well.  相似文献   

10.
Corn masa by‐product streams are high in fiber and are amenable for utilization in livestock feed rations. This approach is a potentially viable alternative to landfilling, the traditional disposal method for these processing residues. Suspended solids were separated from a masa processing waste stream, blended with soybean meal at four levels (0, 10, 20, and 30% wb), and extruded in a laboratory‐scale extruder at speeds of 50 rpm (5.24 rad/sec) and 100 rpm (10.47 rad/sec) with temperature profiles of 80‐90‐100°C and 100‐110‐120°C. Processing conditions, including dough and die temperatures, drive torque, specific mechanical energy consumption, product and feed material throughput rates, dough apparent viscosity, and dough density, were monitored during extrusion. The resulting products were subjected to physical and nutritional characterization to determine the effects of processing conditions for these blends. Extrudate analysis included moisture content, water activity, crude protein, in vitro protein digestibility, crude fat, ash, product diameter, expansion ratios, unit and true density, color, water absorption and solubility, and durability. All blends were suitable for extrusion at the processing conditions used. Blend ratio had little effect on either processing parameters or extrudate properties; extrusion temperature and screw speed, on the other hand, significantly affected both processing and product properties.  相似文献   

11.
Extrusion trials were conducted with varying levels of distillers dried grains with solubles (DDGS) along with soy flour, corn flour, fish meal, vitamin mix, mineral mix, and net protein content adjusted to 28% using a Wenger TX-52 twin-screw extruder. The properties of extrudates were studied in experiments conducted using a full-factorial design with three levels of DDGS content, two levels of moisture content, and two levels of screw speed. Increasing the DDGS content from 20 to 60% resulted in a 36.7% decrease in the radial expansion, leading to a 159 and 61.4% increase in the unit density and bulk density of the extrudates, respectively. Increasing the DDGS content resulted in a significant increase in the water absorption index (WAI) but a significant decrease in the water solubility index (WSI) of the extrudates. Changing the screw speed and moisture content had no significant effect on the radial expansion ratio but resulted in a significant difference in the bulk density of the extrudates, which may be due to the occurrence of longitudinal expansion. Even though changing the moisture content and screw speed had no significant effect on the WSI of the extrudates, significant differences in the WAI of the extrudates were observed. The ingredient components in the blend and moisture content had an influence on the color changes of the extrudates, as did the biochemical changes occurring inside the barrel during processing. Overall, it was determined that DDGS could be included at a rate of up to 60% using twin-screw extrusion, and that viable pelleted floating feeds can be produced.  相似文献   

12.
Distillers dried grains with solubles (DDGS) is the main coproduct of the U.S. fuel ethanol industry and has significantly impacted the livestock feed markets in recent years. Particle agglomeration and subsequent flowability problems during storage and transport are often a hindrance, a nuisance, and expensive. This paper aims at characterizing the glass transition (Tg) and sticky point (Ts) temperatures of DDGS samples prepared with varying condensed distillers solubles (CDS) levels (10, 15, and 20%, wb), drying temperatures (100, 200, and 300°C), and moisture contents (0, 10, and 20%, db), and it discusses implications on DDGS flowability behavior. Distillers wet grains were combined with specified levels of CDS and dried in a convection‐style laboratory oven to produce DDGS. Subsequently, predetermined amounts of water were added to the DDGS to achieve desired moisture content levels. To determine Tg (°C), a differential scanning calorimeter was used, whereas Ts (°C) was determined through a novel technique with a rheometer. Results indicated high correlations between observed Ts and observed Tg (R2 = 0.87) data for DDGS samples. Also, the empirical model for predicted Tg = f (drying temperature, CDS level, and moisture content) based on the Gordon–Taylor model showed favorable R2 (0.74). Stickiness of DDGS increased with an increase in moisture content, indicating flow problems resulting from moisture. It was found that drying temperatures and CDS levels each had significant effects on Tg and Ts as well.  相似文献   

13.
A fractional factorial design with a replicated central composite point was used to investigate the effects of extrusion processing on physical properties of distillers dried grains with solubles (DDGS) based aquafeeds using a twin‐screw extruder. Extrusion cooking trials were performed with a nutritionally balanced ingredient blend for Nile tilapia, with two levels of screw speed (350 and 450 rpm), two levels of extruder water (0.236 and 0.302 kg/min), and two levels of conditioner steam (0.1 and 0.15 kg/min). The central point was 400 rpm screw speed, 0.271 kg/min extruder water, and 0.12 kg/min conditioner steam. Effects of these processing conditions on extrudate characteristics were extensively analyzed and included moisture content, water activity, thermal properties, expansion ratio, unit density, bulk density, color, water stability, sinking velocity, water absorption and solubility indices, and pellet durability index. Increasing the extruder water and conditioner steam resulted in a 5.3% decrease and nearly 8.6% rise in mass flow rate, respectively. As screw speed increased from 350 to 400 rpm, water stability and water activity increased by 13 and 58%, respectively. Increasing extruder water from 0.236 to 0.302 kg/min led to a significant increase in water stability by 12.5% and decreases in water absorption index, water activity, and expansion ratio by 13, 21, and 5.5%, respectively. As conditioner steam increased from 0.1 to 0.15 kg/min, sinking velocity and water absorption index decreased by 25 and 15%, respectively. Increasing conditioner steam from 0.1 to 0.12 kg/min resulted in 20, 5.5, 10, and 3% decreases in moisture content of the extrudates, brightness (L*), water stability, and expansion ratio, respectively. It also increased bulk density by 5.8% and unit density by 4.2%. Overall, all trials produced viable extrudates with properties appropriate for Nile tilapia feeding.  相似文献   

14.
The objective of this study was to establish methods for determining the content and components of residual starch in distiller's dried grains with solubles (DDGS), a coproduct from dry‐grind corn ethanol production. Four DDGS prepared in our laboratory and one DDGS obtained from a commercial ethanol manufacturer were used for the study. Quantitative analysis of total residual sugar (TRS) in DDGS was performed by determining d ‐glucose produced by enzymatic hydrolysis of oligosaccharides and residual starch remaining in hexane‐defatted DDGS after being dispersed in 90% DMSO. The TRS consisted of free glucose, oligosaccharides, and residual starch. The commercial manufacturer's DDGS contained more TRS (15.8%, w/w db) than the laboratory‐processed DDGS (2.4–2.9%, w/w db). The content of residual starch remaining in the commercial DDGS (5.5% w/w db) was also larger than the laboratory‐processed DDGS (1.9–2.5% w/w db). Analyses of molecular weight distribution showed that the residual starch in DDGS consisted of short‐chain amylose and amylopectin, respectively, as the major and minor components. The short‐chain amylose molecules constituted 86.5–94.1% of the residual starch. The major population of the short‐chain amyloses had an average degree of polymerization (DP) of 85, closely resembling the length of enzyme‐resistant fragments of amylose‐lipid complexes.  相似文献   

15.
One of the fastest growing industries in the United States is the fuel ethanol industry. In terms of ethanol production capability, the industry has grown by more than 600% since the year 2000. The major coproducts from corn‐based ethanol include distillers dried grains with solubles (DDGS) and carbon dioxide. DDGS is used as a livestock feed because it contains high quantities of protein, fiber, amino acids, and other nutrients. The goal of this study was to quantify various chemical and physical properties of DDGS, distillers wet grains (DWG), and distillers dried grain (DDG) from several plants in South Dakota. Chemical properties of the DDGS included crude ash (5.0–21.93%), neutral detergent fiber (NDF) (26.32–43.50%), acid detergent fiber (ADF) (10.82–20.05%), crude fiber (CF) (8.14–12.82%), crude protein (27.4–31.7%), crude fat (7.4–11.6%), and total starch (9.19–14.04%). Physical properties of the DDGS included moisture content (3.54–8.21%), Aw (0.42–0.53), bulk density (467.7–509.38 kg/m3), thermal conductivity (0.05–0.07 W/m·°C), thermal diffusivity (0.1–0.17 mm2/sec), color L* (36.56–50.17), a* (5.2–10.79), b* (12.53–23.36), and angle of repose (25.7–47.04°). These properties were also determined for DWG and DDG. We also conducted image analysis and size determination of the DDGS particles. Carbon group characterization in the DDGS and DDG samples were determined using NMR spectroscopy; O‐alkyl comprised >50% of all DDGS samples. Results from this study showed several possibilities for using DDGS in applications other than animal feed. Possibilities include harvesting residual sugars, producing additional ethanol, producing value‐added compounds, using as food‐grade additives, or even using as inert fillers for biocomposites.  相似文献   

16.
《Cereal Chemistry》2017,94(6):934-941
Distillers dried grains with solubles (DDGS) are widely used as feed for cattle, dairy, and swine because of their protein, fiber, amino acids, fat, and other vital nutrients. Corn ethanol plants in the United States recently have started extracting oil from DDGS to gain additional profit, thus producing low‐oil DDGS. So far, there has been no comprehensive study reported with bulk handling and flowability properties of low‐oil DDGS. We measured the air resistance, moisture diffusivity, and air permeability properties for low‐oil DDGS at different temperature and relative humidity conditions, along with some important physical and chemical properties. Physical property comparisons between regular and low‐oil DDGS showed differences in key properties such as particle size, color, density, porosity, and angle of repose. The modified Henderson model predicted the equilibrium moisture content (EMC)–equilibrium relative humidity (ERH) relationship of low‐oil DDGS with a low standard error of regression value (0.008); it showed no pattern in the residuals and was judged the most appropriate model tested for EMC‐ERH predictions. Results of EMC‐ERH nonlinear modeling were used to define conditions for moisture diffusivity. Moisture diffusivities of low‐oil DDGS at varying drying temperatures ranged from 0.74 × 10−11 to 1.77 ×10−11m2/s. The properties are important for understanding and modeling heat and moisture transport through and flow properties of low‐oil DDGS.  相似文献   

17.
With the U.S. fuel ethanol industry projected to grow during the next several years, supplies of distillers dried grains with solubles (DDGS) are anticipated to continue to grow as well. DDGS is used primarily as livestock feed. Much of the DDGS must be shipped, often over large distances, outside the Corn Belt (which is where most of the corn‐based ethanol plants are currently located). Stickiness and caking among particles is a common issue for DDGS, and it often leads to flowability problems. To address this, the objective of this study was to understand the cross‐sectional and surface natures of DDGS particles from five ethanol plants, and how they interact with DDGS properties. This study examined the distribution patterns of chemical components within cross‐sections, within section edges (i.e., surface layers), and on surfaces using standard staining techniques; chemical composition was determined using standard protocols; and physical and flowability properties were also determined. Crude protein in the samples was 28.33–30.65% db, crude fat was 9.40–10.98% db, and neutral detergent fiber (NDF) was 31.84–39.90% db. Moisture contents were 4.61–8.08% db, and geometric mean diameters were 0.37–0.52 mm. Cross‐sectional staining showed protein levels of 19.57–40.39%, and carbohydrate levels of 22.17–43.06%, depending on the particle size examined and the production plant from which the DDGS was sampled. Staining of DDGS particles indicated a higher amount of surface layer protein compared with carbohydrate thickness in DDGS particles that had a lower flow function index (which indicated potential flow issues). Additionally, surface fat staining suggested that higher surface fat also occurred in samples with worse flow problems. This study represents another step toward understanding why DDGS particles stick together during storage and transport, and will hopefully help to improve DDGS material handling strategies.  相似文献   

18.
Extrusion with CO2 injection was developed to simplify the process of producing vacuum‐puffed yukwa (rice snacks). The effects of feed moisture content and CO2 injection on the characteristics of extruded pellets (maximum viscosity and degree of gelatinization) and vacuum‐puffed yukwa (expansion ratio, bulk density, hardness, and color) were investigated. Higher feed moisture increased the size of vacuum‐puffed yukwa and the degree of gelatinization, whereas the maximum viscosity decreased. Maximum viscosity and gelatinization degree of extruded pellets were highly correlated with expansion ratio, bulk density, hardness, and color values of vacuum‐puffed yukwa. Increasing feed moisture content significantly increased expansion ratio but decreased bulk density and hardness. CO2 injection decreased bulk density and hardness of vacuum‐puffed yukwa.  相似文献   

19.
  相似文献   

20.
In various Latin American countries, large volumes of potato are classified as unsuitable for use as food and destined for use as feed. This raw material has a high starch and fiber content that could be used in the production of different kinds of food. The objective of this research was the preparation and characterization of extruded whole potato pellets expanded by microwave heating. A 33 central composite routable experimental design and response surface methodology were used. The barrel temperature (BT, 93–127°C), feed moisture (FM, 19–29%), and corn starch concentration (CS, 3–37%) in the blends were evaluated. CS was the most important variable affecting the functional properties of the expanded pellets. Adding CS to the blends increased the expansion index and viscosity and improved luminosity, decreasing the apparent density and breaking force of the products. Low BT and especially high FM increased the luminosity of the expanded pellets. Increasing FM content increased the viscosity of the expanded pellets. The best functional characteristics for the expanded pellets were obtained using a blend of 63% potato flour and 37% CS, extruded at 110°C BT with 24% FM content. Nonfood-grade whole potato flour showed good potential for use in the production of expanded pellets with acceptable functional properties.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号