首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 15 毫秒
1.
The objective of this study is to develop an advanced stab proof material composed of shear thickening fluid (STF) and Kevlar fabric. In this study, silica/ethylene glycol suspension was prepared for the use as the STF, and it was analyzed by a rheometer, TEM and dynamic light scattering spectrophotometer. From the results, it was observed that the STF significantly showed the reversible liquid-solid transition at a certain shear rate. Also, we treated Kevlar plain fabric with the STF by 1 dip-1nip finishing method and investigated the mechanical and stab resistant properties. Through the investigation of the fumed silica/Kevlar composite fabric, we found that the STF impregnation significantly improved the stab resistance of Kevlar fabric against spike threats and so enhance the protection performance of Kevlar fabric as a stab proof material.  相似文献   

2.
The quasi-static (QS) puncture resistance of p-aramid Twaron fabric impregnated with shear thickening fluid (STF) based on the molecular weight variation of the base liquid has been investigated. To synthesis the STF, the 12 nm silica particles have been dispersed in polyethylene glycol (PEG) with two different molecular weights, 200 and 400 g/mol by means of mechanical mixing. The weight percentages of silica particles in the continuous phase were selected as 15, 25 and 35 wt%. The results of rheological tests indicate that with the increase of the polymer’s molecular weight, the viscosity and instability of the suspension increase, while its critical shear rate diminishes. The STF impregnated Twaron fabrics were subjected to QS puncture resistance tests according to the ASTM standard D6264. The quasi-static puncture resistance increased about 4.5 fold for Twaron fabric impregnated with 35 wt% concentration STF relative to the neat Twaron. Also, with the increase of the PEG’s molecular weight in Twaron fabrics impregnated with 15 and 25 wt% concentration STFs, the QS puncture resistance of Twaron fabrics improved considerably, but it didn’t change too much in the Twaron fabric impregnated with 35 wt% concentration STF.  相似文献   

3.
The energy of impact must decay and be transmitted after a bullet is shot through a ballistic-resistant cloth with a laminate structure. A rigid net structure transmits the impact stress to reduce the breakage of the material in the direction perpendicular to the fabric after the impacting of a projectile. This work combines the rigid net structure of stainless steel mesh with two layers a needle-punched polyamide nonwoven fabric to create a sandwich-like laminate structure. A compound fabric that is composed of a stainless steel mesh and polyamide nonwoven fabrics is placed in multi-layer Kevlar fabrics, and the buffer effect is measured by performing a dropping weight impact test and a bullet-shooting test. The specifications of the stainless steel mesh and the order of placement of the compound fabrics are varied to show the effect of these parameters on the energy of fracture propagation and the buffer effect of the multi-layered Kevlar compound fabric that includes a layer of compound fabric that is made of stainless steel mesh and polyamide nonwoven fabrics. In this study, the compound fabric replaces several layers of Kevlar unidirectional fabric, to be used to reduce the cost of bulletproof vests without reducing ballistic resistance.  相似文献   

4.
In the first stage, polyethylene terephthalate (PET) fibers and Kevlar fibers are combined at a blending ratio of 80/ 20 wt% in order to form PET/Kevlar nonwoven fabrics. Two pieces of PET/Kevlar nonwoven fabrics that enclose a carbonfiber (CF) interlayer are then needle punched in order to form PET/Kevlar/CF (PKC) composites. In the second stage, the sandwiches compose PKC composites as the top and the bottom layers, as well as an interlayer that is composed of a spacer fabric and polyurethane (PU) foam. PU foams have different densities of 200, 210, 220, 230, and 240 kg/m3. These resulting nonwoven fabric/spacer fabric/PU foam sandwiches are then tested using a drop-weight impact test, a compression test, a bursting strength test, a sound absorption test, and a horizontal burning test. The test results indicate that the optimal properties of sandwiches occur with their corresponding PU foam density as follows: an optimal residual stress (240 kg/m3), an optimal compressive strength (240 kg/m3), and an optimal bursting strength (220 kg/m3). In addition, the sandwiches reach the HF1 level according to the horizontal burning test results. They also have an average electromagnetic interference shielding effectiveness of -48 dB, as well as a sound absorption coefficient of 0.5 in a frequency between 1500-2500 Hz, which indicates a satisfactory sound absorption effect. The nonwoven fabric/spacer fabric/PU foam sandwiches proposed in this study are mechanically strong, sound absorbent, and fire retardant, and can be used in construction material and electromagnetic shielding composites.  相似文献   

5.
The purpose of the research is to investigate the fabric structure (with gripping yarns) in influencing ballistic performance aiming to improve the ballistic performance of the currently used body armour materials. Thirteen different fabrics having gripping yarn were designed along fabric warp and/or weft directions. Their ballistic performance in terms of energy absorption has been studied and comparisons made among the single layered fabrics and between the two double layered fabrics, as well as to the conventional used a plain woven fabric for both cases. It was found that fabrics with gripping yarns have improved fabric ballistic performance. The inter-jointed two-layer fabric performed better than the un-jointed two-layer fabric, and it showed a 16.6 % increase in the energy absorption. The implication of the research is that body armour can be made lighter without reducing ballistic impact performance by using gripping yarns.  相似文献   

6.
This study proposes a combination for reciprocal reinforcement between warp knitting spacer fabrics and PU foams. PET/Kevlar nonwoven fabrics are made with an 80:20 ratio and an incorporation of various needle-punching speed of 100, 150, 200, 250, and 300 needles/min. Ascribing to having an optimal bursting strength, sound absorption coefficient, and limited oxygen index (LOI), the PET/Kevlar nonwoven fabric that is made by 200 needles/min are selected to be combined with a glass-fiber fabric by applying needle punch in order to form a surface layer. Next, warp knitting spacer fabrics and the nonwoven fabrics are laminated, followed by being combined with polyurethane (PU) foam that are featured with different densities of 200, 210, 220, 230, and 240 kg/m3 in order to form spacer fabric/PU foam composites with multiple functions. The composites are then tested with a drop-weight test, a compression test, a bursting strength test, a sound absorption test, and a horizontal burning test. The test results indicate that all spacer fabric/PU foam composites reach a horizontal burning level of HF1, and their sound absorption coefficients at 2500-4000 Hz also suggest a satisfactory sound absorption. In particular, the optimal residual stress and compressive strength are present when the composites contain 210 kg/m3 PU foam. Similarly, the optimal bursting strength of the composites occurs when they are composed of 230 kg/m3 PU foam. The spacer fabric/PU foam composites are proven to have high strengths, sound absorption, and fire retardant, and thus have promising potentials for use as construction materials and light weight composite planks.  相似文献   

7.
Woven Kenaf/Kevlar Hybrid Yarn is the combination of natural and synthetic fibers in the form of thread or yarn. The yarn is weaved to form a fabric type of fiber reinforced material. Then, the fabric is fabricated with epoxy as the resin to form a hybrid composite. For composite fabrication, woven fabric Kenaf/Kevlar hybrid yarn composite was prepared with vacuum bagging hand lay-up method. Woven fabric Kenaf/Kevlar hybrid yarn composite was fabricated with total fiber content of 40 % and 60 % of Epoxy as the matrix. The fiber ratios of Kenaf/Kevlar hybrid yarn were varied in weight fraction of 30/70, 50/50 and 70/30 respectively. The composites of woven fabric Kenaf/Epoxy and woven fabric Kevlar/Epoxy were also fabricated for comparison. The mechanical properties of five (5) samples composites were tested accordingly. Result has shown that of value of strength and modulus woven fabric Kenaf/Kevlar Hybrid Yarn composite was increased when the Kevlar fiber content increased. Therefore, among the hybrid composite samples result showed the woven fabric Kenaf/Kevlar Hybrid Yarn composites with the composition of 30/70 ratio has exhibited the highest energy absorption with 148.8 J which 28 % lower than Kevlar 100 % sample. The finding indicated there is a potential combination of natural fiber with synthetic fiber that can be fabricated as the composite material for the application of high performance product.  相似文献   

8.
The aim of this study was to understand the effects of softening treatment on pull-out properties of plain, ribs and satin fabrics. Polyester woven fabrics were used to conduct the pull-out tests. Data generated from these tests included pullout force, crimp extension and fabric displacement. A developed yarn pull-out fixture was used to perform single and multiple pull-out tests on treated and untreated polyester fabrics. Yarn pull-out forces depend on fabric treatments, fabric density, fabric weave, and the number of pulled ends in the fabric. The results of regression model showed that multiple and single yarn pull-out forces of treated fabrics were lower than those of untreated fabrics. The multiple yarn pull-out force was higher than that of the single yarn pull-out force, and that dense fabric had a high pull-out force. Treated and untreated plain fabrics had high single and multiple pull-out forces compared to those of treated and untreated ribs and satin fabrics. Yarn crimp extension depends on directional crimp ratios in the fabric and the number of pulled yarn ends. High directional crimp ratio fabric showed high directional yarn crimp extension. Fabric displacement depends on the number of pulled yarn ends and also fabric treatments. Fabric displacement in multiple pull-out tests showed high fabric displacement compared to that of single pull-out tests. On the other hand, the regression model could be used in this study as a viable and reliable tool.  相似文献   

9.
This study investigated the effects of impregnation modification via vacuum resin impregnation on physical and mechanical properties of sugar palm (Arenga pinnata) fibres. The fibre was evacuated at a constant impregnation pressure of 1000 mmHg impregnation times (0, 5, 10, 15, 20 and 25 min) with two different impregnation agents: phenol formaldehyde (PF) and unsaturated polyester (UP). A notable improvement in the physical properties of sugar palm fibres was observed after they were impregnated with PF and UP for 5 min, shown by the reduction of their moisture content (91 % and 89 %, respectively) and water absorption (43 % and 41 %, respectively) compared to the control sample. However, no significant improvement (p≤0.05) in the physical properties of fibre was observed when the impregnation time was extended (from 10 to 25 min) using both impregnation agents. As for the mechanical properties of the fibre, significant improvement was observed after they were impregnated for 5 min. The fibres impregnated with UP resulted in better fibre toughness and improved mechanical properties as shown in their higher tensile strength and elongation at break compared to the fibres impregnated with PF. Both the physical and mechanical properties showed no significant improvement (p≤0.05) after time for impregnation was extended (from 10 to 25 min) using both impregnation agents. Therefore, it can be concluded that the physical and mechanical properties of sugar palm fibre could be enhanced by impregnating the fibre with thermosetting polymer (PF and UP) for 5 min. It was shown that impregnation with unsaturated polyester (UP) showed better improvement than phenol formaldehyde (PF). In addition, this study also concluded that the unsatisfactory enhancement of the properties of sugar palm fibre even after the impregnation time was extended from 10 to 25 min was due to the use of low impregnation pressure of 1000 mmHg.  相似文献   

10.
The paper discusses a method to functionalize cotton fabrics using biologically active natural compounds to achieve the antibacterial characteristics required for medical application. The biologically active natural compounds include propolis, beeswax, and chitosan. Three 100 % cotton knitted fabrics with different degrees of compactness were impregnated in the emulsions containing the active ingredients and fabric variant G3 with the highest degree of impregnation was considered for the evaluation of the antibacterial properties and comfort characteristics. The results show that the treated cotton fabric had high antibacterial activity against both gram positive bacteria Staphylococcus aureus and Streptococcus β haemolytic, and gram negative bacteria Escherichia coli and Pseudomonas aeruginosa. The presence of the biologically active natural compounds on the cotton substrates modified the surface of the textile fibers as seen in the SEM images. The treatment also improved fabric comfort properties, the cotton substrates became less air permissive and more hygroscopic after the treatment. The experimental results indicated that propolis, beeswax and chitosan can be applied as an emulsion to functionalize cotton textile materials. The antibacterial performance of the functionalized fabrics suggested that the cotton fabrics treated with those biologically active natural compounds have the potentials to be used in medical fields.  相似文献   

11.
In this study, the ballistic impact performance of woven kenaf-Kevlar hybrid and non-hybrid composites against fragment simulating projectiles (FSPs) was investigated. All the composites were prepared using the hand lay-up technique, method, followed by static load compression. The hybrid composites consist of Kevlar fabric and woven kenaf layers. The results obtained indicate that the energy absorption, ballistic limit velocity (V 50) and failure behaviour of the composites during the impact event were affected by the woven kenaf hybridisation. The additional kenaf layers in hybrid composites resulted in the increase in composites thickness and areal density, thus increased the energy absorption (14.46 % to 41.30 %) and V 50 (5.5 % to 8.44 %). It was observed that the hybrid composites failed through a combination of fibre shear, delamination and fibre fracture in the impacted surface, woven kenaf-Kevlar interface and rear surface respectively. Although the specific energy absorption was lower for the hybrid composites, further investigations need to be carried out to utilise the great potential natural fibres.  相似文献   

12.
In this study, durable antibacterial cotton fabrics were prepared by a simple two-step impregnation method. Firstly, thioglycolic acid (TGA) was grafted onto cotton fabric via esterification with the hydroxyl groups of cellulose, then silver nanoparticles (Ag NPs) were immobilized on the cotton fabric surface via coordination bonds with the TGA thiol groups. As a result, the mean size of Ag NPs coating on the cotton fabric is around 74 nm, and these functionalized cotton fabrics show superior antibacterial properties and excellent laundering durability. After withstand 50 laundering cycles, the obtained cotton fabrics still showed outstanding bacterial reduction rates (BR) against both S. aureus and E. coli, and the rates are all higher than 97 %. Therefore, this method to prepare antibacterial cotton fabric shows great potential applications in socks, cosmetic, and medical textiles.  相似文献   

13.
Nano-SiOx suspension was prepared for its unique optical performance to improve the anti-ultraviolet property of cotton fabric in this paper. The experimental results showed that UV-resistance property of thus treated fabrics had been enhanced significantly. The spectrum of absorption, reflection, and transmittance of the treated fabric was analyzed during the optimized processing. The mechanical property of the treated fabric displayed a little increase compared with the original untreated fabric. The morphology of the treated fabric was studied by SEM. The UPF (Ultraviolet Protection Factor) of the fabric treated with nano-SiOx suspension reached 62, much higher than that of the original untreated fabric. Moreover, after 50 home launderings, the UV-blocking property of treated fabric changed little due to the strong affinity between the nano-SiOx particles and cotton fiber.  相似文献   

14.
A porous complex structured woven fabric was manufactured to maximize the moisture transition ability of the prepared fabric by increasing the absorptive property of the fabric through surface modification using plasma, which is a dry modification method. Porous single and complex structured woven fabrics were produced by applying pattern, porosity, and plasma technology, including fabric patterning based on the sheath/core complex structure, the formation of porosity by removing the weft thread or warp thread, and hydrophilic surface treatment using plasma and the improvement in water absorption of different fabrics by the porous and plasma treatment was investigated. Therefore, two different types of fabrics were prepared. One is the porous single structured FAB-SINGLE fabric which was taken out in the direction of the Polyester (PET) warp thread of a general single structure to form a porous. Another is FAB-COMPLEX fabrics that the water-soluble polylactic acid (PLA) yarns with a 1.7 to 2.0 times longer absorption distance than that of PET yarns were inserted into the weft threads, and the PLA yarns were dissolved in a solvent to form the porous complex fabric. And then the physical properties and water absorption of the two types of fabric were compared after the plasma treatment. The results showed that when the FAB-SINGLE fabric, which has porosity induced by the removal of the warp threads in a certain gap, was plasma treated for 5 min, the contact angle was decreased to the extent that a measurement of the contact angle was impossible, whereas the fabric that had not undergone a plasma treatment had a contact angle of 123.6 o. The contact angle of the FABCOMPLEX with porosity caused by the dissolution of the PLA yarns was reduced from 76.8 o to 0 o after 3 minutes of a lowtemperature plasma treatment, indicating that the hydrophilic property was increased. In addition, the water absorption measurements showed that the absorption height was increased from 2.3 cm of the fabric sample that had not been treated with plasma to the highest absorption height of 8.3 cm, suggesting that the water absorption also increased with the improvements in moisture transition ability by the plasma treatment. The physical tensile strength of the fabrics was not changed by the plasma treatment, despite the changes on the fabric surface, suggesting that the combination of double complex structures and the plasma treatment helped improve the water absorption.  相似文献   

15.
In this research work, behavior of flexural stiffness of core spun cotton spandex single jersey, 1x1 rib and interlock fabrics was studied under relaxation and machine washing treatments. Results are compared with similar fabrics made from 100 % cotton. Fabric weight density increased with the progression of treatments and it is proportionate to the fabric tightness factor (stitch length?1). Even though both types of fabrics had same machine set stitch lengths, cotton/spandex fabrics have shown the higher fabric weight densities than that of 100 % cotton fabrics. Although 1x1 rib and single jersey fabrics knitted with the same machine set stitch lengths, rib fabrics have given higher fabric weight densities than single jersey fabrics. Among the three knitted structures, interlock fabrics with higher machine set stitch lengths gave the higher fabric weights. Fabric stiffness and flexural rigidity have given higher values under the progression of treatments and it was found that higher values of stiffness have given by cotton/spandex knitted fabrics compared to their cotton fabrics. Fabric stiffness and flexural rigidity in wale direction were higher than that in course direction, but it is only observed in single jersey fabrics. However, 1x1 rib and interlock fabrics have shown an opposite behavior. It was also observed a positive correlation between TF (i.e.: stitch length?1) and bending length/flexural rigidity in both fabric types. Lower flexural rigidities reported with single jersey structures and highest values gave with interlock structures of cotton/spandex and cotton fabrics.  相似文献   

16.
Impact behaviors of the large deformable composites of Kevlar fiber reinforced composites of different preform structures have been investigated. An analytic tool was developed to characterize the impact behavior of the Kevlar composites. The image analysis technique, and deply technique were employed to develop energy balance equation under impact loading. An energy method was employed to establish the impact energy absorption mechanism of Kevlar multiaxial warp knitted composites. The total impact energy was classified into four categories including delamination energy, membrane energy, bending energy and rebounding energy under low velocity impact. Membrane and bending energy were calculated from the image analysis of the deformed shape of impacted specimen and delamination energy was calculated using the deplying technique. Also, the impact behavior of Kevlar composites under high velocity impact of full penetration of the composite specimen was studied. The energy absorption mechanisms under high velocity impact were modelled and the absorbed energy was classified into global deformation energy, shear-out energy, deformation energy and fiber breakage energy. The total energy obtained from the model corresponded reasonably well with the experimental results.  相似文献   

17.
The aim of the presented research was to study the influence of surface layer material on improvement of impact, dielectric, EMI shielding and sound absorption properties of sandwich composites. The sandwich composite structure consisted of Kevlar or Carbon woven fabric at the surface layer, recycled high loft nonwoven in the center and a mixture of carbon particles/epoxy matrix as a binder to hold the surface layer and core together. The carbon particles were incorporated in epoxy in order to improve failure mechanism and enhance dielectric properties or electromagnetic shielding of sandwich composites. The biggest improvements on impact properties of sandwich composites were obtained when Kevlar fabric was used as surface layer. However, surface layer of carbon fabric was found to provide better dielectric properties and improve EMI shielding of sandwich composites against Kevlar fabric surface layer.  相似文献   

18.
The effects of chemical treatment on the mechanical, morphological, and chemical resistance properties of uniaxial natural fabrics, Grewia tilifolia/epoxy composites, were studied. In order to enhance the interfacial bonding between the epoxy matrix and the Grewia tilifolia fabrics, two different types of treatment: alkali treatment (5 % NaOH) and (3-aminopropyl)-triethoxysilane coupling agent (CA), were used. The epoxy composites containing 0–15 wt% of Grewia tilifolia fabric were prepared by hand lay-up technique, at room temperature. The tensile and flexural properties of the untreated, alkali-treated and coupling agent treated Grewia tilifolia reinforced epoxy composites were determined as a function of fabric loading. The 9 % wt Grewia tilifolia fabric reinforced epoxy composites showed improved tensile and flexural modulii when compared to the neat epoxy matrix. Significant improvement in the mechanical properties was obtained when both alkali and coupling agent treated fabrics were used as reinforcement. Morphological studies demonstrated that better adhesion between the fabrics and the matrix was achieved especially when the alkali-treated and coupling agent treated Grewia tilifolia fabrics were used in the composites. For the water absorption and chemical resistance studies, various solvents, acids and alkalis were used on the epoxy composites. This study has shown that Grewia tilifolia fabric/epoxy composites are promising candidates for structural applications, where high strength and stiffness are required.  相似文献   

19.
Treatment of polyacrylonitrile (PAN) onto m-aramid fabric was carried out by pad-dry-cure method using dimethylformamide (DMF) dissolved acrylic fiber solution. The obtained PAN treated m-aramid fabric was dyed using exhaustion method with basic dyes. The effect of PAN treatment on fabric stiffness property was acceptable with acrylic fiber solutions ranging from 1 wt% to 4 wt%. Whilst, more than 4 wt% PAN treated fabrics exhibited undesirable stiffness. The dyeing results showed that PAN treated m-aramid fabrics exhibited a significant increase in color strength when compared to untreated fabric, arising from an increase in anionic dye sites (styrene SO3 ? group). Wash fastness was comparable to that of untreated fabric, indicating the strong interaction between dye molecules and the PAN. Rubbing fastness of treated fabrics was not affected by treatments with PAN concentrations lower than 4 wt%. Further increase in PAN concentration led to poorer rubbing fastness property due to the problem of surface dyeing. For light fastness, the PAN treatment failed to improve the light fastness property which is the main disadvantage of basic dyeing of aramid fabric. Finally, in case of PAN treatments with the range of 1 wt% to 4 wt%, the flame retardancy property of PAN treated m-aramid fabrics was found not affected by the percent add-on. However, above 4 wt% PAN treatment, the flame retardancy performance became deteriorated.  相似文献   

20.
In this work, we developed a new method that can achieve immobilization and protection of the Cu NPs coating on the cotton fabrics by a simple two-step impregnation method. Firstly, L-cysteine (Cys) was grafted onto cotton fabric via esterification with the hydroxyl groups of cellulose, then Cu NPs were introduced on the fabric surface in the presence of a protective reagent, citric acid. Due to the doubled stabilization acts of Cys and citric acid, the Cu NPs immobilized on the fabric surface showed an excellent antibacterial effect and outstanding laundering durability. As a result, the mean size of the Cu NPs coating on the cotton fabric is about 62.4 nm, and the modified cotton fabrics showed satisfactory antibacterial ability against both S. aureus and E. coli, which the bacterial reduction rates are all higher than 98 % even withstand 50 washing cycles. Therefore, this method to prepare antibacterial cotton fabrics showed great potential applications in socks, cosmetic, and medical textiles.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号