首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 31 毫秒
1.
Castor oil was converted to maleated castor oil (MACO) without any catalyst. MACO was characterized with FTIR, NMR, molecular weight and viscosity measurement. Tung oil (20 wt%) was added to MACO as reactive diluent. Non-woven jute felts were used as reinforcing material. The MACO was polymerized and crosslinked in situ during composite fabrication. The curing behavior of MACO with free radical catalyst was investigated by differential scanning calorimetry (DSC). The MACO/jute composites were tested for their flexural properties, impact strength and dynamic mechanical properties and compared with similar unsaturated polyester resin/jute composites. The flexural moduli of both the composites were nearly similar. The impact strength of MACO/jute composites was 42% higher than that of UPE/jute composites. The damping property of the MACO/jute composites was higher than that of UPE/jute composites over a wide range of temperature.  相似文献   

2.
The aim of this study was to evaluate the potential of the fibrous material obtained from ethanol-water fractionation of bagasse as reinforcement of thermoplastic starches in order to improve their mechanical properties. The composites were elaborated using matrices of corn and cassava starches plasticized with 30 wt% glycerin. The mixtures (0, 5, 10 and 15 wt% bagasse fiber) were elaborated in a rheometer at 150 °C. The mixtures obtained were pressed on a hot plate press at 155 °C. The test specimens were obtained according to ASTM D638. Tensile tests, moisture absorption tests for 24 days (20-23 °C and 53% RH, ASTM E104), and dynamic-mechanical analyses (DMA) in tensile mode were carried out. Images by scanning electron microscopy (SEM) and X-ray diffraction were obtained. Fibers (10 wt% bagasse fiber) increased tensile strength by 44% and 47% compared to corn and cassava starches, respectively. The reinforcement (15 wt% bagasse fiber) increased more than fourfold the elastic modulus on starch matrices. The storage modulus at 30 °C (E30 °C′) increased as the bagasse fiber content increased, following the trend of tensile elastic modulus. The results indicate that these fibers have potential applications in the development of biodegradable composite materials.  相似文献   

3.
Composites consisting of polyurethane (PU)/carbon nanotubes (CNTs) have been successfully prepared by solution mixing method. CNTs were modified through mechano-chemical reaction to increase the compatibility with PU via hydrogen bondings. SEM microphotographs proved that modified CNTs (M-CNTs) became shorter and FTIR spectra showed that hydroxyl groups had been introduced to the surface of M-CNTs. SEM images of PU/M-CNTs composites also proved that M-CNTs were effectively dispersed in PU matrix. Mechanical property tests showed that addition of M-CNTs could significantly improve the tensile properties of PU/M-CNTs composite (breaking strength enhancement ratio for composite with 5.0 wt% M-CNTs was 103.81 %). The thermal stability of composites with M-CNTs was also improved. The initial degradation temperature enhancement was 19.9 oC for the composite with 0.5 wt% M-CNTs. Electrical property tests showed that the electrical properties were improved by adding M-CNTs. The volume conductivities increased 3 and 5 orders of magnitude for the composites with 5.0 wt% and 10 wt% M-CNTs, respectively. The addition of M-CNTs had little effect on the elastic properties of the composites.  相似文献   

4.
The effects of chemical treatment on the mechanical, morphological, and chemical resistance properties of uniaxial natural fabrics, Grewia tilifolia/epoxy composites, were studied. In order to enhance the interfacial bonding between the epoxy matrix and the Grewia tilifolia fabrics, two different types of treatment: alkali treatment (5 % NaOH) and (3-aminopropyl)-triethoxysilane coupling agent (CA), were used. The epoxy composites containing 0–15 wt% of Grewia tilifolia fabric were prepared by hand lay-up technique, at room temperature. The tensile and flexural properties of the untreated, alkali-treated and coupling agent treated Grewia tilifolia reinforced epoxy composites were determined as a function of fabric loading. The 9 % wt Grewia tilifolia fabric reinforced epoxy composites showed improved tensile and flexural modulii when compared to the neat epoxy matrix. Significant improvement in the mechanical properties was obtained when both alkali and coupling agent treated fabrics were used as reinforcement. Morphological studies demonstrated that better adhesion between the fabrics and the matrix was achieved especially when the alkali-treated and coupling agent treated Grewia tilifolia fabrics were used in the composites. For the water absorption and chemical resistance studies, various solvents, acids and alkalis were used on the epoxy composites. This study has shown that Grewia tilifolia fabric/epoxy composites are promising candidates for structural applications, where high strength and stiffness are required.  相似文献   

5.
An ionic liquid (IL)-water mixture employed to treat lignocellulosic biomass is promising. The addition of water decreases viscosity and process cost so as to improve the IL practical application. In this work, effects of temperature (50-170 °C), water content (0-80 wt%), treating duration (0.5-4 h) and pressure (0.1-3.2 MPa) on treating legume straw process using a 1-butyl-3-methylimidazolium chloride ([C4mim]Cl)-water mixture were experimentally investigated. Legume straw was found to be partially dissolved, and the dissolved substances can be flocculated by adding the coagulating agent—water (equal to volume of the solution). For this process at 0.1 MPa, the maximum 29.1 wt% legume straw is dissolved in the [C4mim]Cl-water mixture with water content of 20 wt% at 150 °C during 2 h, which is much higher than 9.8 wt% using pure [C4mim]Cl. A hemicellulose-free lignin-rich material (64.0 wt% lignin and 35.3 wt% cellulose) is obtained by adding the water. Even for 0.5 h, 22.3 wt% of legume straw is dissolved in the case of water content of 20 wt%, 150 °C and 0.1 MPa. High pressure favors the dissolution of legume straw but lignin content in the residue has no obvious change. The addition of proper amount of water facilitates the dissolution of legume straw and a relative rapid dissolving rate can be achieved in a [C4mim]Cl-water mixture. There are great differences in chemical and physical properties between legume straw and the obtained samples (residue and floc) due to the dissolution and reconstitution.  相似文献   

6.
The current study was initiated to characterize various parts of nipa palm (Nypa fruticans) to establish whole utilization of this biomass as potential raw material for fuels and chemicals. Nipa consisting of frond, shell, husk and leaf was chemically characterized for cellulose, hemicellulose, lignin, starch, protein, extractives and inorganic constituents for its each part. The total chemical composition showed that the cellulose and hemicellulose contents were in the range of 28.9-45.6 wt% and 21.8-26.4 wt%, respectively. The hemicellulose was rich with glucuronoxylan. The lignin content was 19.4-33.8 wt% with the highest lignin content found in leaf. The alkaline nitrobenzene oxidation products showed that nipa palm lignin mainly consists of guaiacyl and syringyl propane units with a small amount of p-hydroxyphenylpropane unit. Besides the main chemical components, starch, protein and extractives were also present in significant amounts from 2 to 8 wt%. Additionally, the ash content was high from 5.1 to 11.7 wt%, consisting of the major inorganic elements being Na, K and Cl with minor inorganic elements of Mg, Ca, Si, P, S and Al. Overall, each part of the nipa palm has its individual superior characteristics and could be exploited as lignocellulosic resources for fuels and chemicals.  相似文献   

7.
Chemical treatment is an often-followed route to improve the physical and mechanical properties of natural fiber reinforced polymer matrix composites. In this study, the effect of chemical treatment on physical and mechanical properties of jute fiber reinforced polypropylene (PP) biocomposites with different fiber loading (5, 10, 15, and 20 wt%) were investigated. Before being manufactured jute fiber/PP composite, raw jute fiber was chemically treated with succinic anhydride for the chemical reaction with cellulose hydroxyl group of fiber and to increase adhesion and compatibility to the polymer matrix. Jute fiber/PP composites were fabricated using high voltage hot compression technique. Fourier Transform Infrared spectroscopy (FTIR) and Scanning Electron Microscopy (SEM) tests were employed to evaluate the morphological properties of composite. Succinic anhydride underwent a chemical reaction with raw jute fiber which was confirmed through FTIR results. SEM micrographs of the fractured surface area were taken to study the fiber/matrix interface adhesion and compatibility. Reduced fiber agglomeration and improved interfacial bonding was observed under SEM in the case of treated jute fiber/PP composites. The mechanical properties of jute/PP composite in terms of Tensile strength and Young’s modulus was found to be increased with fiber loading up to 15 wt% and decreased at 20 wt%. Conversely, flexural strength and flexural modulus increased with fiber loading up to 10 wt% and start decreasing at 15 wt%. The treated jute/PP composite samples had higher hardness (Rockwell) and lower water absorption value compared to that of the untreated ones.  相似文献   

8.
Jute fabrics reinforced thermoset composites were prepared with different formulations using urethane acrylate oligomer, methanol, and benzyl peroxide. Jute fabrics were soaked in the prepared formulations and fiber content in the composites was optimized with the extent of mechanical properties. Among all the resulting composites, 55 wt% jute content at oligomer:methanol:benzyl peroxide=75:24.5:0.5 (w/w/w) ratio showed best mechanical properties. The optimized jute fabrics were cured under UV radiation at different intensities and their mechanical properties were measured. Jute fabrics were treated with potassium permanganate (KMnO4) solution of different concentrations (0.01, 0.02, 0.03, and 0.05 wt%) for different soaking times (1–5 min) before the composite fabrication. Optimized jute fabrics (jute fabrics treated with 0.02 wt% KMnO4 for 2 min soaking time) were soaked in the optimized formulation and cured under UV radiation at different intensities and measured their mechanical properties. Scanning electron microscopic investigation showed that surface modification improves fiber/matrix adhesion. Water uptake and soil degradation test of the treated and untreated composite samples were also performed.  相似文献   

9.
The aim of this paper is to demonstrate for the first time the technological potential of novel, totally bio-based, binder-free vegetable fiber-composites based on the reed-like plant Typha sp. Binder-free vegetable fiberboards based on Cattails were prepared and their mechanical (flexural modulus of elasticity, flexural strength and water absorption) and surface textural properties were determined. The influence of press time and panel density on the properties was investigated. In contrast to currently known natural fiber composites based on hemp, flax, kenaf or the like annual plants which all require up to 30 wt% of suitable bonding resins, the typha based composites were prepared completely without the addition of any extraneous glue and showed good mechanical performance that clearly exceeded the performance of other natural fiber composites containing low percentages of phenolic binder (15%). Of special interest were the superior surface properties of the typha based panels. Despite the coarse nature of the raw fiber material and the rough texture of the typha based fiber mats, binder-free typha panels showed excellent surface smoothness which makes this novel composite material highly interesting for light-weight applications with high surface quality standards, for example, as powder-coated elements for the automotive and furniture industries.  相似文献   

10.
A simple method based on the combination of the intercalation from solution and melt-processing preparation methods was used to prepare highly exfoliated and compatible thermoplastic starch (TPS) and montmorillonite clay (MMT) nanocomposites. The effects of the MMT content on the thermal, structural, and mechanical properties of the nanocomposites were investigated. XRD diffraction was used to investigate the MMT exfoliation/intercalation degrees in the TPS matrix. Data from thermogravimetric analysis and differential scanning calorimetry revealed that the addition of MMT increased the thermal stabilities of TPS nanocomposites. Young's modulus and tensile strength increased from 8.0 to 23.8 MPa and 1.5 to 2.8 MPa with an increasing MMT content from 0 to 5 wt% without diminishing their flexibility. The improvement in such properties can be attributed to the good dispersion/exfoliation of MMT in the TPS matrix. Combining both methods, it was possible to obtain homogenous and transparent nanocomposites with excellent thermal and mechanical properties for application as packaging materials.  相似文献   

11.
The impacts of acidic soils and Al toxicity on wheat nutrient economy have been scarcely researched under field conditions even though these soils are widely spread in wheat production areas around the world. The main objective of this study was to quantitatively evaluate the element (N, P, K, Ca and Al) economy of an Al-sensitive and an Al-tolerant wheat cultivar growing under different soil Al concentrations at field conditions. To reach this objective, two field experiments were conducted in an Andisol in Valdivia (39°47′18″S, 73°14′05″W), Chile. Treatments were a factorial arrangement of: (i) two spring wheat cultivars (Al-sensitive, Domo.INIA and Al-tolerant, Dalcahue.INIA) and (ii) five exchangeable Al levels (0-2.7 cmol(+) kg−1) with three replicates. At harvest, plant biomass was sampled and divided into 5 organ categories: ears, grains, blade leaves, stems plus sheath leaves and roots. The element content (N, P, K, Ca and Al) in each organ was measured to quantify element uptake and concentration, nutrient uptake efficiency (UPE) and nutrient utilization efficiency (UTE). Element uptake (N, P, K, Ca, and Al) was negatively affected by the increased soil Al concentration in above-ground and root biomass in both cultivars (R2 = 0.61-0.98, p < 0.01), although clear differences were found between cultivars. On the contrary, the impact of soil exchangeable Al on the plant element concentration was minor, showing weak associations with soil Al levels. However, the Al concentration in above-ground tissues of the Al-sensitive cultivar was an exception because it increased exponentially with the Al soil concentration (R2 = 0.96-0.99, p < 0.001). Nutrient uptake efficiencies, UPEs (N, P, K and Ca), were negatively affected by soil Al concentrations and were well described by linear equations in both cultivars (R2 = 0.58-0.98, p < 0.05), with notable differences between them. Both nutrient uptake (capture) and UPE were the traits that best explained above-ground biomass production (R2 = 0.82-0.99, p < 0.001, n = 20). Nutrient utilization efficiency, UTEs (N, P, K and Ca) responded more conservatively to the soil Al concentration, except for the Al sensitive cultivar under very high soil Al levels.  相似文献   

12.
This study was conducted to evaluate the suitability of using residual plant fibers from agricultural waste streams as reinforcement in thermoplastic composites. Three groups of plant fibers evaluated included cotton burrs, sticks and linters from cotton gin waste (CGW), guayule whole plant, and guayule bagasse. The plant fibers were characterized for physical (bulk density and particle size distribution) and chemical properties (ash, lignin and cellulose contents). A laboratory experiment was designed with five fiber filler treatments, namely control (oak wood fiber as the filler - OWF), cotton burr and sticks (CBS), CBS with 2% (by weight) second cut linters (CBL), CBS with 30% (by weight) guayule whole plant (CGP), and CBS with 30% (by weight) guayule bagasse (CGB). The composite samples were manufactured with 50% of fiber filler, 40% of virgin high-density polyethylene (HDPE), and 10% other additives by weight. The samples were extruded to approximately 32 × 7 mm cross-sectional profiles, and tested for physico-mechanical properties. The CBS and CBL had considerably lower bulk density than the other fibers. Cotton linters had the highest α-cellulose (66.6%), and lowest hemicellulose (15.8%) and lignin (10.5%) of all fibers tested. Guayule whole plant had the lowest α-cellulose and highest ash content. Both CBS and guayule bagasse contained α-cellulose comparable to OWF, but slightly lower hemicellulose. Evaluation of composite samples made from the five fiber treatments indicated that fibers from cotton gin byproducts and guayule byproducts reduced the specific gravity of the composites significantly. However, the CBS and CBL samples exhibited high water absorption and thickness swelling, but the addition of guayule bagasse reduced both properties to similar levels as the wood fiber. The CGP exhibited significantly lower coefficient of thermal expansion. Composite samples with the five different fiber fillers showed similar hardness and nail holding capacity, yet oak fibers imparted superior strength and modulus under flexure and compression with the exception of the compressive modulus of CGB composites. In general, both cotton ginning and guayule processing byproducts hold great potential as fiber fillers in thermoplastic composites.  相似文献   

13.
Jute fabrics (hessian cloth) reinforced polypropylene (PP) matrix composites (45 wt% fiber) were fabricated by compression molding. Jute fabrics were treated with 2-hydroxyethyl methacrylate (HEMA) using ultraviolet radiation in order to improve the mechanical properties of the composites. Concentration of HEMA, soaking time and radiation dose were optimized. It was found that 15% HEMA in methanol along with photoinitiator Darocur-1173 (2 %), 10 min soaking time and 20th pass of radiation rendered better performance. Urea of different concentrations (0.5–2 %) was incorporated with 15 % HEMA to monitor its effect on the properties and 1 % urea revealed the best results. For the improvement of the properties, jute fabrics were treated with potassium permanganate (KMnO4) solution in acetone of different concentrations (0.02, 0.03, 0.05, and 0.5 %) at different soaking times (1, 2, 3, and 5 min) before the composite fabrication. Optimized jute fabrics (jute fabrics treated with 0.03 % KMnO4) were again treated with HEMA (15 %) solution along with urea (1 %) and promising improvement of mechanical properties of the composites was observed. Scanning electron microscopy, water uptake, soil degradation and thermal aging of the treated and untreated composites were also performed.  相似文献   

14.
The graphene oxide (GO) sheets are chemically grafted with γ-etheroxygentrimethoxysilane (KH560) and liquid crystalline epoxy (LCE) is synthesized from 4,4′-bis(2-hydroxyhexoxy)biphenyl (BP2) and epichlorohydrin before being incorporated into epoxy matrix. Then we present a novel approach to the fabrication of advanced polymer composites from epoxy matrix by incorporation of two modifiers, which are grafted GO (g-GO) and LCE. The mechanical properties of epoxy composites are greatly improved by incorporating LCE/g-GO hybrid fillers. For instance, the addition of 3 wt% hybrid filler (2 wt% g-GO and 1 wt% LCE) into the epoxy matrix resulted in the increases in impact strength by 132.6 %, tensile strength by 27.6 % and flexural strength by 37.5 %. Moreover, LCE/g-GO hybrid fillers are effective to increase thermal decomposition temperature, glass transition temperature, and storage modulus by strong affinity between the fillers and epoxy matrix.  相似文献   

15.
The objective was to study the potential of grain by-products (husk) of grains such as wheat (Triticum aestivum L; German name is Weizen) and rice (Oryza sativa) as reinforcements for thermoplastics as an alternative to or in combination with wood fibres. Prior to composites preparation, the chemical components of fibres such as cellulose, hemi-cellulose, lignin, starch, protein and fat were measured and the surface chemistry and functionality of grain by-products were studied using EDX and FT-IR. Structural constituents (cellulose, starch) were found in wheat husk (W) equal 42%, in rice husk 50% and in soft wood 42%, respectively. Thermal degradation characteristics, the bulk density, water absorption and the solubility index were also investigated. Wheat husk (W) and rice husk were found thermally stable at temperatures as low as 178 °C and 208 °C, respectively. The particle morphology and particle size were investigated using microscopy. Water absorption properties of the fibres were studied to evaluate the viability of these fibres as reinforcements. Polypropylene composites were fabricated using a high speed mixer and an ensuing injection moulding process with 40 wt% fibre. The tensile and Charpy impact strength of the resulting composites were investigated. The tensile elongation at break was found to 75% for wheat husk (W) composites and 23% for rice husk composites better than soft wood composites. Rice husk composites showed 13% better Charpy impact strength than soft wood composites. Due to coupling agent, tensile strength of composites found to improve 25% for soft wood, 35% for wheat husk (W) and 45% for rice husk.  相似文献   

16.
Aqueous dispersions of starch–soybean oil (SBO) and starch–jojoba oil (JO) composites, prepared by excess steam jet cooking, form effective dry film lubricants when applied as thick coatings to metal surfaces by a doctor blade. This application method necessitates long drying times, is wasteful, requires the addition of sucrose to promote composite adhesion to the metal surface, and restricts the substrate geometry to planar surfaces. These issues represent important barriers to the commercialization of this aqueous biobased dry film lubricant technology. We now report an air-assisted spray method that uses readily available spray equipment to apply aqueous starch–oil composite dispersions as thin coatings (0.15–2.0 mg/cm2) to metal surfaces quickly and efficiently. Aqueous dispersions of waxy maize starch–oil composites containing either SBO, JO or hexadecane (HD), having 0.020–31.7 wt% oil relative to starch, were applied by air-assisted spraying and could be dried to the touch in approximately 30 s. Additionally, sucrose was found unnecessary for adhesion of the sprayed coatings. Tribological ball-on-flat testing of metal specimens spray coated with starch–SBO, –JO, and –HD composites showed the thin films of starch–SBO and –JO performed better at reducing the coefficient of friction (COF) than the starch–hexadecane composites. A low COF ranging between 0.027 and 0.044 was obtained for the starch–SBO and –JO composites containing 4–5 wt% oil relative to starch. Above 4–5 wt% oil loadings, no further COF reductions were realized. Further results revealed that micrometer-sized oil droplets embedded within the dried starch matrix of the composite film are delivered “on demand”. It appears that when pressure is applied to the dry film lubricant, the starch matrix ruptures and releases the entrained oil to the friction surface.  相似文献   

17.
Cassava bagasse is an inexpensive and broadly available waste byproduct from cassava starch production. It contains roughly 50% cassava starch along with mostly fiber and could be a valuable feedstock for various bioproducts. Cassava bagasse and cassava starch were used in this study to make fiber-reinforced thermoplastic starch (TPSB and TPSI, respectively). In addition, blends of poly (lactic acid) and TPSI (20%) and TPSB (5, 10, 15, 20%) were prepared as a means of producing low cost composite materials with good performance. The TPS and PLA blends were prepared by extrusion and their morphological, mechanical, spectral, and thermal properties were evaluated. The results showed the feasibility of obtaining thermoplastic starches from cassava bagasse. The presence of fiber in the bagasse acted as reinforcement in the TPS matrix and increased the maximum tensile strength (0.60 MPa) and the tensile modulus (41.6 MPa) compared to cassava starch TPS (0.40 and 2.04 MPa, respectively). As expected, blending TPS with PLA reduced the tensile strength (55.4 MPa) and modulus (2.4 GPa) of neat PLA. At higher TPSB content (20%) the maximum strength (19.9 MPa) and tensile modulus (1.7 GPa) were reduced about 64% and 32%, respectively, compared to the PLA matrix. In comparison, the tensile strength (16.7) and modulus (1.2 GPa) of PLA blends made with TPSI were reduced 70% and 51% respectively. The fiber from the cassava bagasse was considered a filler since no increase in tensile strength of PLA/TPS blends was observed. The TPSI (33.1%) had higher elongation to break compared to both TPSB (4.9%) and PLA (2.6%). The elongation to break increased from 2.6% to 14.5% by blending TPSI with PLA. In contrast, elongation to break decreased slightly by blending TPSB with PLA. Thermal analysis indicated there was some low level of interaction between PLA and TPS. In PLA/TPSB blends, the TPSB increased the crystallinity of the PLA component compared to neat PLA. The fiber component of TPSB appeared to have a nucleating effect favoring PLA crystallization.  相似文献   

18.
Enhancement of the mechanical and vibrational properties of glass/polyester composites was aimed via matrix modification technique. To achieve this, unsaturated polyester was modified by incorporation of oligomeric siloxane in the concentration range of 1–3 wt%. Modified matrix composites reinforced with woven roving glass fabric were compared with untreated glass/polyester in terms of mechanical and interlaminar properties by conducting tensile, flexure, and short-beam shear tests. It was found that after incorporation of 3 % oligomeric siloxane into the polyester matrix, the tensile, flexural, and interlaminar shear strength (ILSS) values of the resulting composite increased by 16, 15, and 75 %, respectively. The increases in ILSS as well as in tensile and flexural properties were considered to be an indication of better fiber/matrix interaction as confirmed by SEM fractography images. Furthermore, the effect of oligomeric siloxane incorporation on the vibrational properties of the composites was investigated by experimental modal testing and the natural frequencies of the composites were found to increase with increasing siloxane concentration.  相似文献   

19.
Mature red fruits of Opuntia ficus-indica contain two soluble pigment, betanin and indicaxanthin. The optimal conditions for dye extraction were to mix 50 g of juice from cactus pears with 100 mL of acidified water as solvent for dye extraction. Two main dyes were purified from the pigment extract by chromatography and identified by UV-vis, HPLC and LC-MS techniques as indicaxanthin (15 mg per 100 g) and betanin (280 mg per 100 g). The effect of dye bath pH, salt concentration, dyeing time and temperature was studied. The optimal conditions for dyeing modified acrylic fabrics with betanin dye were carried out at 50 °C for 45 min at pH 5. Un-mordanted samples have good properties of water and washing fastness. Mordant CoSO4 was found to give good light fastness (rating 5).  相似文献   

20.
Many research reported vegetable oil as a potential substitute for diesel engines with its ester form known as biodiesel. The biodiesel can be prepared by different process using vegetable oil and alcohol. The common process used for biodiesel preparation is known as transesterification. This paper presents the transesterification of Sal oil (Shorea robusta) into Sal oil methyl ester (SOME) and its performance in direct injection diesel engine. Several process parameters such as catalyst quantity, molar ratio of alcohol, reaction temperature and reaction time were studied and the optimized process conditions are amount of catalyst (NaOH) - 0.25 wt%, alcohol (methanol) - 150% excess, reaction temperature - 65 °C and reaction time - 1.5 h. The studies with SOME as fuel in the direct injection diesel engine shows that the exhaust emissions such as CO, HC and NOx are reduced by 25%, 45% and 12%, respectively compared to diesel without significant difference in thermal efficiency. Based on this study it is concluded that the SOME can be used as fuel without any modifications in the engine and hence this biodiesel can be a potential substitute to standard diesel fuel.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号