共查询到20条相似文献，搜索用时 93 毫秒
1.
2.
《西部林业科学》2015,(2)
利用短纤维代替粉状材料作为增强材料制备纤维增强型聚丙烯基复合材料,研究不同的木纤维/聚丙烯配比、密度以及不同浓度的碱处理对木纤维/聚丙烯复合材料物理力学性能的影响。结果表明,目标密度仅为0.55g/cm3时,且当木纤维与聚丙烯的配比为30︰70时,木纤维/聚丙烯复合材料表现出最佳的物理力学性能,但仍达不到标准要求。因此,综合产品成本和物理力学性能,选取了50︰50的原料配比,研究密度对该产品物理力学性能的影响。进一步研究表明,随着密度的增加,复合材料的力学强度得到不断提高,当密度为0.70g/cm3时,板材的力学性能就可以满足国标要求但吸水厚度膨胀率不能满足国标要求。当密度为0.83 g/cm3时,板材的力学性能满足国标要求,吸水厚度膨胀率有减小的趋势。为了进一步提高该复合材料的物理力学性能,利用浓度分别为1%,3%和5%的氢氧化钠溶液对木材纤维和工业大麻杆纤维进行处理,结果表明,经过碱处理后复合材料的吸水厚度膨胀率减小了,静曲强度和弹性模量仍可满足标准要求。 相似文献
3.
4.
5.
通过对4种厚度规格、5种含水率的刨花板与其吸水厚度膨胀率的关系进行研究,结果表明:刨花板的厚度越大,含水率越高,其吸水厚度膨胀率越小,板厚对吸水厚度膨胀率的影响大于含水率;对吸水厚度膨胀率与厚度、含水率建立了显著的二元线性回归方程,经过检测拟合度较高. 相似文献
6.
7.
本文研究了配料比对木纤维／聚丙烯复合材料物理力学性能的影响,研究结果表明：随着聚丙烯用量的增加,木纤维／聚丙烯复合材料的弹性模量、静曲强度呈先上升后下降趋势。当聚丙烯用量为25％左右时,弹性模量和静曲强度均达到较大值;随着聚丙烯用量的增加,吸水厚度膨胀率呈下降趋势,而密度略呈上升趋势。 相似文献
8.
为充分利用农作物废弃物,研究环境友好材料,通过热压成型方法制备稻秸/淀粉胶全降解复合材料。研究了预处理、胶黏剂、增塑剂和阻湿剂含量对复合材料内结合强度(IB)、弯曲强度(FS)、弯曲弹性模量(MOE)、冲击韧性(IR)、拉伸强度(TS)、拉伸模量(MOR)、含水率及2h吸水厚度膨胀率的影响,并观察了复合材料细观表面。结果表明:水热处理复合材料力学性能除IB外均较高;含胶量为10%时力学性能除MOR外均较高;1%增塑剂提高了IB、FS及TS,2%增塑剂提高了IS,增塑剂对MOE和MOR有负面影响;阻湿剂降低了复合材料力学性能。增塑剂、阻湿剂均能不同程度的增大复合材料MC。复合材料2h吸水厚度膨胀率大,防水性能差。复合材料基体和增强体两相界面结合存在明显缝隙、空洞及分层现象。 相似文献
9.
竹塑复合材料吸水性能的研究 总被引：5，自引：1，他引：4
对楠竹/新PE、楠竹/回收PE、杂竹/回收PE 3种竹塑复合材料的吸水性能进行了研究,结果表明:(1)温度是影响竹塑复合材料吸水厚度膨胀率和吸水率的主要因素之一。(2)3种竹塑复合材料厚度方向吸水膨胀性和吸水率表现为:杂竹/回收PE材料吸水膨胀性最大,楠竹/新PE次之,楠竹/回收PE最小。(3)杂竹/回收PE在80℃时的吸水率是室温下的3.5倍;楠竹/新PE和楠竹/回收PE在80℃条件下的吸水率均是室温下的3倍。(4)楠竹/回收PE在80℃水浴中的厚度方向吸水膨胀率是55℃下的1.4倍,是室温下的2倍;楠竹/新PE80℃水浴下吸水膨胀率是55℃下的1.2倍,是室温下的1.9倍;杂竹/回收PE 80℃水浴下吸水膨胀率是55℃下的1.6倍,是室温下的2倍多。(5)光学显微镜和扫描电镜观察后发现,吸水后竹塑复合材料除了竹纤维发生膨胀之外,材料的内部结构没有发生变化,即竹塑复合材料是一种具有良好抗湿膨胀性能的新型复合材料。 相似文献
10.
11.
《Scandinavian Journal of Forest Research》2012,27(5):427-435
In Scandinavia, moose (Alces alces L.) sometimes cause severe browsing damage to economically-important pine. Moose-vehicle accidents have spurred construction of fences along roads, and these may interfere with moose migration between summer and winter ranges, or the road alone may be a barrier. If this happens and moose build up along roads, landowners may suffer economically. Therefore, this study investigated whether roads, fences or other factors influence the use of young pine stands by moose. Eighty stands along roads in northern Sweden were evaluated in which individually-browsed branches were counted on 9972 pines. Moose browsing was not significantly related to birch (Betula pendula Roth, B. pubescens Ehrh.) density, nor did it differ between pines (Pinus contorta Douglas or P. sylvestris L.). However, increased pine density, site productivity and proximity to a highway were associated with increased browsing. Further large-scale studies are needed to understand moose habitat selection and the effects of roads. 相似文献
12.
《Scandinavian Journal of Forest Research》2012,27(3):206-217
The root systems of 2-yr-old Picea glauca, Picea mariana and Pinus banksiana seedlings were submitted to various frost temperatures during an artificial frost to induce different levels of root damage. Frost-damaged and control seedlings were placed in a greenhouse under high and low soil moisture regimes. Seedling growth and physiology were evaluated periodically. Seedling survival was reduced when root damage reached levels of 60-80%. Root systems of all three species showed partial to total recovery by the end of the experiment. In general, root freezing damage caused reductions in seedling growth, with these reductions becoming less significant over time. Root damage had little to no effect on black spruce and jack pine seedling physiology, while white spruce CO 2 uptake decreased with increasing root damage. Shoot nitrogen content of all three species decreased slightly with increasing root damage. 相似文献
13.
Contour hedgerows of multipurpose tree species in the sloping tea lands of Sri Lanka are expected to reduce soil erosion and
also add significant amounts of plant nutrients to the soil via periodic prunings. The objective of this experiment was to characterize the biomass decomposition pattern and quantify the
amount of nutrients added through prunings of six tree species (Calliandra calothyrsus, Senna spectabilis, Euphatorium innulifolium, Flemingia congesta, Gliricidia sepium and Tithonia diversifolia) currently being used in hedgerows associated with tea. Withered leaf and stem prunings (50 g) were enclosed in 2-mm litter
bags, placed at 5-cm depth and retrieved after one, three, six, nine and 12 weeks. Loss of initial dry weight, N, P and K
was measured. Single exponential decay function adequately described both dry weight and nutrient loss. Tree species differed
significantly in their rate of breakdown with decomposition constants (k) varying from 0.0299 to 0.2006 week−1 for leaves and from 0.0225 to 0.0633 week−1 for stems. Gliricidia showed the highest k for leaves with the rest in the following descending order: Senna > Tithonia ≥ Euphatorium > Calliandra > Flemingia. A similar pattern was observed for loss of all nutrients with Calliandra and Flemingia always having lower k values than the rest. Although N immobilization was not observed, immobilization of P and K was observed
during the first week of incubation in some species, particularly in stem prunings. Annual biomass of prunings differed significantly
between tree species in the following descending order: Calliandra > Senna > Flemingia > Tithonia > Gliricidia > Euphatorium. Calliandra added the greatest amount of nutrients annually to the soil with Euphatorium adding the least. Calliandra prunings provided the annual total K requirement and 49% of the N requirement of mature tea. However, none of the species
provided more than 5% of the P requirement. It is concluded that among the tree species tested, Calliandra and Flemingia are the most suitable for contour hedgerows in tea plantations of this agroclimatic region because of their higher soil nutrient
enrichment capacity and slower decomposition rates which would minimize leaching losses.
This revised version was published online in June 2006 with corrections to the Cover Date. 相似文献
14.
《Scandinavian Journal of Forest Research》2012,27(1):53-61
This study investigated the stand structure in pine, spruce and deciduous forests in the border district of Finland and Russia. A total of 46 mature forest stands was selected as pairs, the members of each pair being as similar as possible with respect to their forest site type, age, moisture and topography. The stands were then compared between the two countries by means of basal areas and number of stems. The proportions of dominating tree species were 2-12% lower, and correspondingly the proportions of secondary tree species higher, in Russian forests. The density of the forest stock was also higher in each forest type in Russia. The forests in the two countries differed most radically in terms of the abundance of dead trees. The amount was two to four times higher in Russian deciduous and spruce forests, and in pine forests the difference was 10-fold. The stand structures indicated that Russian coniferous stands, in particular, were more heterogeneous than intensively managed pine and spruce stands in Finland. 相似文献
15.
《Scandinavian Journal of Forest Research》2012,27(1):15-27
The root collar diameter and the height:diameter ratio are of particular importance in container-grown seedlings where a high density in the containers may produce spindly seedlings. Temperature regimes and light quality are known to affect plant growth. The aim of this study was to identify responses in Picea abies (L.) Karst. seedlings grown with light providing different red:far-red ratios and under temperature regimes with alternating day (DT) and night temperature (NT) from negative (DT < NT) to positive (DT > NT) difference (DIF) between DT and NT. Experiments were conducted in controlled environment chambers and in a daylight phytotron. Only limited thermoperiodic responses appeared in P . abies seedlings with respect to seedling height and dry weight accumulation. The formation of terminal buds, however, was clearly delayed in seedlings grown at negative DIF. The results indicate a requirement for day extension light that is high in far-red, to prevent terminal bud formation under natural short-day conditions. An extended study should be conducted to clarify the minimum level of light intensity and the optimal light quality needed to prevent terminal bud formation under natural short-day conditions. 相似文献
16.
本文分析了CAD在设计中引起的正面和负面影响,并进行了系统的阐述,从而使设计者在应用中能够保持客观的态度。 相似文献
17.
《Scandinavian Journal of Forest Research》2012,27(2):118-130
The effects of seed weight and seed type on seedling growth of Pinus sylvestris (L.) were studied by seeding individually weighed orchard and stand seed in different mixtures under harsh (direct seeding in field) and optimal (seeding in nursery) conditions. In the nursery experiment an increase in the seed weight from 3 to 7 mg increased the seedling height by 10-27% and total weight by 27-113%, and decreased the height/diameter ratio by 5-6% after 2 yrs. With elimination of seed weight effects, orchard seedlings were 2% taller than stand seedlings in year 2. Without elimination of seed weight effects, orchard seedlings were 7-13% taller. In the field experiment an increase in the seed weight from 3 to 7 mg increased seedling height by 18-65%, stem volume by 81-274% and the number of top-buds by 23-34% in year 5. After elimination of seed weight effects, orchard seedlings were 7-13% taller than stand seedlings and without elimination of seed weight effects 20-21% taller after 5 yrs. Even after elimination of both seed weight and genetic effects orchard seedlings were 3-9% larger than stand seedlings in the field experiment. In conclusion, the influence of seed weight and seed type on growth traits and slenderness is highly significant and the influence seems to be greater in harsh conditions. 相似文献
18.
Astra Zaluma Lauma Bruna Darta Klavina Natalija Burnevica Kristine Kenigsvalde Andis Lazdins Talis Gaitnieks 《Forest Pathology》2019,49(6)
Heterobasidion parviporum and Heterobasidion annosum are widely distributed root‐rot fungi that infect conifers throughout Europe. Infection of conifer stumps by spores of these pathogens can be controlled by treating fresh stumps with a competing non‐pathogenic fungus, Phlebiopsis gigantea. In this study, growth of three Latvian strains of P. gigantea and the biological control agent ‘Rotstop’ strain was evaluated in stem pieces of Norway spruce, Scots pine, lodgepole pine, Douglas‐fir, Weymouth pine, Siberian larch and Sitka spruce. The growth rates of one H. parviporum and one H. annosum isolate were also measured in the same stem pieces. The growth rate of P. gigantea varied greatly in wood of different conifer species. It was higher in the three pine species, lower in Norway spruce and lowest in Sitka spruce and Siberian larch, and in Douglas‐fir, this fungus did not grow. The largest area of wood occupied by P. gigantea was in lodgepole pine. Growth of Latvian isolates of P. gigantea in the wood of Pinus and Picea species was comparable to that of the Rotstop isolate. Consequently, stump treatment with local P. gigantea isolates should be recommended. However, our results suggest that Douglas‐fir stump treatment against Heterobasidion by P. gigantea may be ineffective and other stump treatment methods should be considered. 相似文献
19.
Steven Maranz Amadou Niang Antoine Kalinganire Djeneba Konaté Bocary Kaya 《Agroforestry Systems》2008,72(3):231-239
Baobab leaves form an important part of the local diet in Sahel countries and elsewhere in Africa. Existing leaf nutritional
data and agroforestry performance information are based solely on Adansonia digitata L., the baobab of continental Africa. The introduction potential of Adansonia species from the center of diversity in Madagascar and from Australia remains untapped. To assess this potential, the mineral
contents and B1 and B2 vitamin levels of dried baobab leaves were determined for five-year old trees of A. digitata, A. gibbosa (A. Cunn.) Guymer ex D. Baum, A. rubrostipa Jum. & H. Perrier (syn. A. fony Baill.), A. perrieri Capuron and A. za Baill. grown in an introduction trial in Mali. Nutritional data were evaluated against survival and vigor to identify promising
germplasm. Leaf vitamin and crude protein contents were highest in the Madagascar species, especially A. rubrostipa (B1 88 mg 100 g−1, B2 187 mg 100 g−1, protein 20.7% dry weight). However, the local species far outperformed the introductions in survival, tree height, basal
diameter and resistance to termites. We suggest grafting as a way of harnessing the vigor of well-adapted local baobab varieties
to the superior nutritional profiles of A. rubrostipa and others. Cross-species grafting tests in Adansonia were successful, thus creating new agroforestry possibilities with different scion/rootstock combinations. 相似文献
20.
《Wood material science & engineering》2013,8(2):76-84
Abstract Wood in general and wooden studs in particular are often distorted owing to uneven shrinkage during the drying process in the sawmill. Twist is often the most detrimental of all types of distortion, and it is caused by spiral grain in combination with variations in moisture content. For sawmills, the objective is to produce dried, straight boards, and one method of dealing with boards with excessive spiral grain is to sort them out and then dry them in a pretwisted position to obtain straight boards after drying. A model using the finite element (FE) method for the simulation of drying twist distortions was first calibrated against laboratory experiments in which boards were dried with and without restraints and pretwists. After the calibration, the FE results were compared with industrial test results for boards that were dried without restraints or with restraints with zero pretwist, i.e. straight restraints. The FE model used an elastic–ideally plastic material model to obtain permanent deformations. The calibration was to set the yield stresses so that there was a good match between FE results and results from the laboratory experiments. The comparison between the industrial test results and the FE results showed that the FE model is capable of realistic simulations of drying boards with and without restraints and presumably also pretwists. 相似文献