排序方式: 共有308条查询结果,搜索用时 15 毫秒
101.
102.
ANSYS在板式家具强度分析中的应用研究 总被引:3,自引:0,他引:3
董宏敢 《林业机械与木工设备》2009,37(5):26-29
分析了有限元软件ANSYS在板式家具强度分析中的应用,提出了ANSYS板式家具搁板强度分析的基本方法。利用ANSYS进行家具结构与强度的分析与优化设计,求解迅速,结果直观,可有效提高设计与分析的效率。 相似文献
103.
Form finding of a cable membrane simulated by ANSYS is a time consuming process and requires high user analytical ability. This is due to the complexity of the steps and the characteristics of ANSYS. We analyzed the theory of the finite element method for form finding, summarized the form finding steps, and put forward how to conduct it in ANSYS. A system using APDL and User Luterface Design Language(UIDL) based on ANSYS was derived. An example was taken to check the accuracy and practicability of the system. This new system can save the engineering designer time and energy and also provide references for the future work. 相似文献
104.
105.
为提高小麦联合收割机的使用寿命、降低收割作业过程中产生的共振,基于ANSYS分析理论,对易产生共振的核心装置进行三维系统建模和优化设计。通过分析联合收割机工作机理及运动特点,根据机械振动理论和激振频率模型,利用UG软件,选取收割机的机架和收割系统作为研究对象,对其进行结构优化后得出三维系统物理模型,并导入ANSYS分析软件进行模态求解分析得出前4阶振型。从振型图可知:优化设计较好避开了共振点。振动试验结果表明:有限元计算的固有频率与振动试验值误差在±8%范围内,机架与割台质量分别降低15. 3%和8. 8%。由此验证了三维系统建模参数设计的合理性与可行性,从而为类似收割机的振动分析提供思路与参考。 相似文献
106.
针对FSAE赛场上普遍使用的瓦特连杆式稳定杆(又称Z-bar),根据汽车侧倾特性进行横向稳定杆的设计和优化。基于瓦特连杆横向稳定的工作原理,计算了赛车侧倾角刚度及横向稳定杆刚度,分析了瓦特连杆结构以及受力情况,进行了尺寸设计及强度校核。通过ANSYS进行结构分析优化,并建立了ADAMS动力学模型,通过动力学仿真,说明了瓦特连杆对悬架参数变化的影响。 相似文献
107.
为了提高车用螺母的安全性、可靠性和轻量化,简化车用螺母的实验过程,本文运用
ANSYS 软件对紧固件螺母进行优化,直观地观察了六角螺母在预紧力作用下的力学特性,对六
角螺母的受力情况进行了静力分析。结果表明:优化前,六角螺母等效应力最大值和最小值都比
较大,优化后,六角螺母等效应力最大值和最小值都相应减小;在预紧力作用下,通过应力释放槽
能够降低螺母结合面上会产生局部应力集中现象;在施加相同挤压力的情况下,应力释放槽起到
了释放应力的效果,减小了螺母的接触面承受的接触应力,提高了螺母的力学性能;优化后六角 相似文献
108.
基于ANSYS软件,对圆锯片进行热力学、静力学和模态分析,揭示各种因素对锯切加工过程中高速旋转状态下圆锯片的影响及其变化规律,从而为研究和改善圆锯片的动态特性提供可靠的理论依据。 相似文献
109.
Abstract:For computational efficiency, numerical simulation analysis of cracks’ development by dry shrinkage effect has been carried out on a practical meeting two storey and single span wall infilled frame structure. FEM models are used as semi discrete type and whole type.Different column rigidity, opening sizes, and connection rigidity are discribed with deformation, stress, crack development results. The crack morphology and width can be comparable with practice.Gravity and vertical loads should be considered in model. Shrinkage causes large deformation near openings. Different column rigidity, opening sizes and connection rigidity cause different crack development and deformation. The uniform construction detailing is not enough for all. Primary crack of non constructional detailing wall infilled frame may happen at -5 ℃ equivalent temperature, and the ultimate crack width can exceed usage permission. At last wall crack width by dry shrinkage is assessed, and some proposals are given. 相似文献
110.
应用ANSYS软件,在三维地层模型下对阵列方位侧向测井仪器进行有限元数值模拟。计算了仪器的某一方位视电阻率响应、伪几何因子及井眼校正曲线。通过对模拟结果分析,发现该仪器除了具有区分同一深度地层不同方位视电阻率变化的特性以外,还有一个重要特性,即阵列方位侧向测井仪器与普通三侧向测井仪器在不同直径井眼校正曲线的相对位置刚好相反。 相似文献