基于单片机的脉码传输仪设计     

蔡昌新  李国芳 《长江大学学报》2006,(4)

以单片机为核心,采用软件、硬件相结合的方法,充分利用单片机的硬件中断资源,实时响应地面的声波逻辑脉冲,分离其接收和发射逻辑。同时该仪器以地面声波逻辑为工作时序,分时采集模拟道数据、脉冲道数据及向地面传输PCM数据。该脉码传输仪既能完成PCM3506的全部功能,又能监测仪器工作环境的温度及测井套管接箍的压力。  相似文献   

水电站虹吸式进水口的控制     

马述江 《中国农村水利水电》1993,(9)

在对河北省几座已建虹吸式进水口水电站的虹吸控制方式进行分析对比的基础上,给出了一种采用液气射流泵将虹吸体抽成“低管”正虹吸,用“Y”形管中的水封保持真空,事故时利用“高管”自动补气破坏真空的控制系统,并分析了该系统的特点,给出了设计计算方法及计算公式。  相似文献   

基于伺服控制系统的MJK6227型往复式裁板锯     

刘青科  杨佳  周玉庭 《林业机械与木工设备》2006,34(5):42-44

通过伺服控制系统在MJK6227型往复式裁板锯上的应用,可以看出与传统的电控系统相比,该机具有较高的灵活性和准确性。便于用户实现较高的工作精度和较为快捷的工作要求。试验表明,系统能够满足该机的各种动作要求,且在工作过程中可以反馈锯片的即时动作。目前,该系统已在铣床、砂光机等数控机床控制系统设计中推广应用。  相似文献   

加热光纤法同步测定土壤水热参数误差分析     

胡优  司炳成  李敏  何海龙  何冬  任姮烨  刘吕刚 《土壤学报》2024,61(4)

土壤水热参数是研究土壤水热传输的基本物理参数。当前热脉冲探针法（HPP）可同步测定土壤水热参数,但该方法仅限于在点尺度下测定。与其具有相同理论基础的加热光纤法（SPHP-DTS）,可将测定尺度增大至田间千米尺度,但其测定精度尚未得到有效验证。为了探知SPHP-DTS法的误差,本研究进行了SPHP-DTS法与HPP法测定土壤水热参数的对比试验。结果表明,以HPP为标准,加热光纤法测定热导率的精度RMSE为0.13 W?m-1?℃-1。SPHP-DTS法测定的热导率显著高于HPP法,主要原因在于加热光纤时产生的温度效应。通过热导率法测定土壤含水率时,在热导率测定误差的影响下,SPHP-DTS法的测定精度明显低于HPP法。SPHP-DTS法测定土壤水热参数的其他误差来源包括光纤与土壤之间多个界面的接触热阻、光纤的温度敏感性、噪音干扰以及温度梯度驱动下的水分迁移。本研究可为SPHP-DTS法提升土壤水热参数测定精度提供理论参考。  相似文献   

液液系统中荷电射流不稳定性     

王晓英  武识博  王贞涛  王军锋  王东保 《排灌机械工程学报》2020,38(6):596-601

针对生物柴油液液静电雾化乳化过程,建立了色散方程并应用Matlab进行数值计算,分析了水射流速度、荷电电压、水与生物柴油各自的黏度、表面张力对生物柴油中水射流不稳定性的影响.研究结果表明,在水-生物柴油系统中,提高水射流的速度或荷电电压,均能使界面波最大增长率增大,对应的最优波数也随之增加.水的黏度阻碍水射流的破碎雾化,而生物柴油黏度对水射流的破碎雾化却起着促进作用.水-生物柴油的界面张力越小,对液液静电雾化乳化过程越有利.在水-生物柴油液液静电雾化乳化实际应用过程中,除提高水射流速度和荷电电压外,提高水的温度同时尽可能地降低生物柴油的温度,可以形成粒径细小均匀离散相液滴,获得优质的生物柴油乳化燃油.  相似文献   

2016/2017冬中国气温偏暖的基本特征及可能成因     

于骐恺  高震  姚素香 《中国农学通报》2020,36(12):79-85

利用中国740余站观测的月平均2 m气温资料以及NCEP/NCAR再分析资料,通过动力学诊断的方法,对2016—2017年中国冬季异常偏暖现象进行了研究。结果发现：中国2016—2017年冬季气温偏暖主要是由于西伯利亚高压和阿留申低压偏弱导致东亚冬季风偏弱,在中国存在异常的偏南风。阿留申低压偏弱由两个因素引起,一是由于阿留申群岛地区的海温偏低,冷源对应异常高压导致阿留申低压偏弱;二是阿留申低压在东亚副热带高空西风急流出口区以北,然而该冬季高空西风急流出口区位置偏南,导致阿留申地区偏离急流出口减压区,从而导致阿留申低压偏弱。此外,西风带偏北,中高纬亚洲大陆上空以纬向环流为主,不利于冷空气南下。  相似文献   

支管射流三通结构优化与试验     

薛子龙  王新坤  樊二东  徐胜荣  王轩  张晨曦 《排灌机械工程学报》2020,38(7):751-756

为了提高支管射流三通水力性能,改善滴灌的灌水均匀性,基于CFX数值模拟技术,对进口宽度为15 mm的支管射流三通进行结构优化.选取位差、劈距、劈尖半径和侧壁倾角为影响因素,通过四因素三水平正交设计了9组模型,边界条件设定为进口压力100 kPa.选取支管射流三通出口设计流量为评价标准,支管射流三通最优结构尺寸为位差5.5 mm、劈距113 mm、劈尖半径13 mm、侧壁倾角10°.此结构尺寸参数下的支管射流三通水力性能试验结果表明:在进口水压为100 kPa时,支管射流三通脉冲频率为148次/min,水头压力振幅为37.9 kPa,水头压力损失为16.7 kPa,出口流量为0.698 L/s;支管射流三通所接滴灌带长度为60 m时,与普通支管三通相比,支管射流三通的灌水均匀系数提高了2.78%,流量偏差率降低了4.72%.该研究可为射流技术在脉冲滴灌系统的研究、开发与应用提供理论依据.  相似文献   

Assessment of pulse co-oximetry technology after in vivo adjustment in anaesthetized dogs     

Hamaseh Tayari  Derek Flaherty  Tyfane T. Yamaoka  Adam Auckburally 《Veterinary anaesthesia and analgesia》2021,48(3):297-304

ObjectiveTo compare values of haemoglobin concentration (SpHb), arterial haemoglobin saturation (SpO₂) and calculated arterial oxygen content (SpOC), measured noninvasively with a pulse co-oximeter before and after in vivo adjustment (via calibration of the device using a measured haemoglobin concentration) with those measured invasively using a spectrophotometric-based blood gas analyser in anaesthetized dogs.Study designProspective observational clinical study.AnimalsA group of 39 adult dogs.MethodsIn all dogs after standard instrumentation, the dorsal metatarsal artery was catheterised for blood sampling, and a pulse co-oximeter probe was applied to the tongue for noninvasive measurements. Paired data for SpHb, SpO₂ and SpOC from the pulse co-oximeter and haemoglobin arterial oxygen saturation (SaO₂) and arterial oxygen content (CaO₂) from the blood gas analyser were obtained before and after in vivo adjustment. Bland–Altman analysis for repeated measurements was used to evaluate the bias, precision and agreement between the pulse co-oximeter and the blood gas analyser. Data are presented as mean differences and 95% limits of agreement (LoA).ResultsA total of 39 data pairs were obtained before in vivo adjustment. The mean invasively measured haemoglobin–SpHb difference was –2.7 g dL^?1 with LoA of –4.9 to –0.5 g dL^?1. After in vivo adjustment, 104 data pairs were obtained. The mean invasively measured haemoglobin–SpHb difference was –0.2 g dL^?1 with LoA of –1.1 to 0.6 g dL^?1. The mean SaO₂–SpO₂ difference was 0.86% with LoA of –0.8% to 2.5% and that between CaO₂–SpOC was 0.66 mL dL^–1 with LoA of –2.59 to 3.91 mL dL^–1.ConclusionsBefore in vivo adjustment, pulse co-oximeter derived values overestimated the spectrophotometric-based blood gas analyser haemoglobin and CaO₂ values. After in vivo adjustment, the accuracy, precision and LoA markedly improved. Therefore, in vivo adjustment is recommended when using this device to monitor SpHb in anaesthetised dogs.  相似文献   

Experimental Investigation on Chip-break Influenced by Cryogenical Cold Air jet     

YANG Ying  TONG Ming-wei  YAN Xing-chun  SHEN Qiang 《保鲜与加工》2004,(5):74-77

In machine cutting, the replacement of traditionalKGcutting solution with cryogenical cold air jet not only possesses a good cooling and lubricating efficiency, but also can avoid the occurrenceof environmental pollution. In order to clarify the manner and performance of discharged cutting chip under cryogenical cold air jet condition, an experiment was carried out for steel grade 45 in the dry and cryogenical cold air jet cutting comparatively. The effects of cryogenical cold air jet on the breaking of cutting chip are discussed. Experimental results reveal that, in the valid ranges of pressure and temperature, the cryogenical cold air jet can widen the chip broken region effectively. Different insufflating angle of cold air behaves different influence on the chip-break. From the experiment, it has been gained that the optimized jet insufflatingangle, temperature effecting range and pressure working range of cold air, which provides the foundation of industrial manufacturing.  相似文献   

LABORATORY INVESTIGATION OF ESSENTIAL CHARACTERISTICS PARAMETERS FOR THE INDUCED-NOZZLE DEVICE     

Zhang Fenghua Liao Zhenfang 《保鲜与加工》1988,(6)

The standoff of a submerged jet is smaller than a non-submerged jet in general. In order to increase the standoff of a submerged jet, the induced-nozzle device is presented with its inducing mechanism analysed in this paper. Under the various inducing medium, the effect of the ratio d2/d1 upon the device's properties is measured. Some reasonable parameters are given. When d2/d1=2.0, approximate straight region of the curve of the jet center line stagnation pressure varying with the standoff is L/d1= l0~12 for inducing air. The induced-nozzle device is compared with the conventional nozzle for shotting some samples. Several applied possibilities of the device are discussed.  相似文献