| 弹性齿对甘蔗茎秆的动态打击力与叶鞘剥离机理研究 |
| |
| 引用本文： | 牟向伟.弹性齿对甘蔗茎秆的动态打击力与叶鞘剥离机理研究[J].农业机械学报,2015,46(3):103-109. |
| |
| 作者姓名： | 牟向伟 |
| |
| 作者单位： | 广西师范大学 |
| |
| 基金项目： | 国家自然科学基金资助项目（51205071）、广西自然科学基金资助项目（2013GXNSFBA019231）和广西师范大学博士科研启动基金资助项目 |
| |
| 摘 要： | 为研究弹性齿式剥叶元件的叶鞘剥离机理,进行了弹性齿对甘蔗茎秆的动态打击力试验。设计专用试验台固定甘蔗茎秆的两端,并在固定组件的3个方向安装单向压电型冲击力传感器,剥叶滚筒带动弹性齿在茎秆中部施加打击力,传感器测得纵向、横向和切向动态打击力并得出最大值Fxmax、Fymax和Fzmax。对剥叶滚筒转速、弹性齿与甘蔗茎秆交错深度、侧偏距离和弹性齿材料等4个变量进行单因素试验。分析各因素对打击力的影响规律,得出在样机剥叶试验的最优参数组合下三向动态打击力的最大值。结合叶鞘材料力学特性和剥离准则模型,推导叶鞘的最大破坏力公式,建立叶鞘剥离的力学模型。结果表明,滚筒转速达到700 r/min、交错深度为30 mm、侧偏距离为20 mm、弹性齿材料为聚氨酯(85 HA)时,弹性齿在x和y方向最大打击力Fxmax、Fymax分别为93.87 N和138.26 N,同时大于叶鞘在相应方向的最大破坏力76.40 N和53.53 N,实现叶鞘剥离。
|
| 关 键 词： | 甘蔗 叶鞘 剥离 机理 弹性齿 打击力 |
| 收稿时间： | 2014/10/18 0:00:00 |
Study on Dynamic Hitting Force of Elastic Dentation for Sugarcane Stalk and Mechanism of Leaf Sheath Stripping |
| |
| Mou Xiangwei.Study on Dynamic Hitting Force of Elastic Dentation for Sugarcane Stalk and Mechanism of Leaf Sheath Stripping[J].Transactions of the Chinese Society of Agricultural Machinery,2015,46(3):103-109. |
| |
| Authors: | Mou Xiangwei |
| |
| Institution: | Guangxi Normal University |
| |
| Abstract: | In order to study the mechanism of sugarcane leaf sheath stripping using elastic dentation typed stripping element, the experiments of three-dimensional dynamic hitting force were conducted under the action of elastic dentation on sugarcane stalks. The specialized test bench was designed to fix the stalk at opposite ends by using two fixed components, and one way type piezoelectric impact sensors were respectively fastened on each fixed component. An elastic dentation driven by the rotating roller hit the middle of the stalk, and the dynamic hitting forces were measured in real time by sensors. After data processing, the maximum values of Fx, Fy and Fz in longitudinal, transversal, and tangential directions were obtained. Four factors including rotate speed of roller, interleaved depth and lateral offset distance between the elastic dentation and stalk, and material of elastic dentation were determined. Single factor experiments were carried out to analyze the effect of factors and obtain the maximum values of dynamic hitting forces in three directions with the optimal parameters combination. The formula of maximum failure force of leaf sheath stripping was deduced and the mechanical model of leaf sheath striping was established which combined with material mechanics properties and leaf sheath stripping criteria. The results showed that the tested maximum values of Fx and Fy were equaled to 93.87N and 138.26N which were greater than the maximum failure force of leaf sheath in x and y directions, 76.40N and 53.53N simultaneously, under the condition that the rotate speed of roller was 700r/min, the interleaved depth was 30mm, the lateral offset distance was 20mm, and the material of elastic dentation was polyurethane with shore hardness 85HA. |
| |
| Keywords: | Sugarcane Leaf sheath Stripping Mechanism Elastic dentation Hitting force |
| 本文献已被 CNKI 万方数据 等数据库收录！ |
| 点击此处可从《农业机械学报》浏览原始摘要信息 |
| 点击此处可从《农业机械学报》下载免费的PDF全文 |
|
