共查询到20条相似文献,搜索用时 156 毫秒
1.
2.
推广应用“无粘结预应力砼结构”郭力伟(正阳河木材厂)赵京南(哈尔滨第三工程公司)宋野(哈尔滨建材工业设计院)郭长源(黑龙江森工总局)后张法无粘结预应力工艺,系在预应力钢筋表面涂以专用防腐油脂的涂料层,外包聚乙烯或聚丙烯的塑料管的外包层;将这种特制加工... 相似文献
3.
4.
根据无粘结部分预应力混凝土梁的受力特点,采用弯矩-曲率法计算无粘结预应力钢筋的极限应力,计算结果与现有的试验数据符合得较好。建立了系统的无粘结部分预应力混凝土简支空心板梁桥设计理论和方法,有助于UPPC梁桥设计理论的完善及发展,并为“公桥规”的修订和完善提供有益的参考。 相似文献
5.
6.
7.
结合无粘结预应力技术在高层结构中的应用,对设计计算基本原理、步骤到参数选择、内力分析等问题进行了较详细的阐述,可供业内人士参考。 相似文献
8.
本文介绍了无粘结预应力筋施工中容易出现的问题及防治方法,对无粘结预应力筋工程的施工有一定指导作用。 相似文献
9.
10.
11.
分析了不同截面对梁结构内力、截面设计的影响,针对不等跨连续梁提出最优线刚度比的概念,并通过PKPM结构设计软件计算出不同截面下梁的框架内力,对比分析出梁的的最优线刚度比,以期达到不等跨连续梁截面尺寸的优化。 相似文献
12.
13.
基于Proe5.0与Ansys—Workbench板材起重运输三工位上料机机架主梁的有限元分析 总被引:1,自引:0,他引:1
使用板材三工位起重运输上料机将大大节省送料周期,提高自动化程度,使板材输送线布置更加合理。在三工位上料机机架受力分析的基础上,利用Proe5.0软件建立了相关的三维模型,并针对其结构强度的相关计算,提出利用Ansys—Workbench软件对上料机机架主梁进行相关校核。 相似文献
14.
在工程设计中,交叠钢筋的上下位置是根据结构的受力特点确定的。因此,施工中应严格按照设计图纸布筋,不可自行改变。本文详细介绍了钢筋砼工程中的基础、梁、板在施工中交叠钢筋的摆放位置及顺序。 相似文献
15.
双梁抛木器是一个由承托梁和滑木梁组合而成的承载梁,失稳后,承托梁向后翻转,原木在重力作用下沿滑木梁抛下,由于结构所致,原木抛落时产生一个惯性力。实验结果表明,该力的存在并不会导致失抛。由落抛时间引起的水平距离很小,不影响小门板的开启长度。 相似文献
16.
17.
In a detailed study of the relation between the deflection caused by shear force and the constitution of a laminated material
beam, we derived an equation for calculating the shear modulus of a laminated material beam from the shear moduli of individual
laminae. The validity of the derived equation was investigated using crosslaminated wood beams made with five species. The
calculated shear moduli parallel to the grain of face laminae ranged from 48.3 MPa to 351 MPa, while those perpendicular to
the grain of face laminae ranged from 58.0 MPa to 350 MPa. The calculated shear moduli increased markedly with increasing
shear modulus in a cross section of perpendicular-direction lamina of a cross-laminated wood beam. The calculated apparent
modulus of elasticity (MOE) of cross-laminated wood beams agreed fairly well with the measured apparent MOE values. This fact
indicated that the apparent MOE of cross-laminated wood beam was able to be calculated from the true MOE values and shear
moduli of individual laminae. The percentage of deflection caused by shear force obtained from the calculated apparent MOE
(Y
sc) was close to that obtained from the measured apparent MOE (Y
s) and there was a high correlation between both values. From the above results, it was concluded that the derived equation
had high validity in calculation of shear modulus of a cross-laminated wood beam. 相似文献
18.
19.
20.
二级扬程80m的森林灭火消防泵主要靠轴承来平衡轴向力,运行过程中泵的噪声和振动较大,轴承磨损严重。改进设计后的三级120m扬程、四级160m扬程泵的轴向力更大,故应考虑加装轴向力平衡装置。结合消防泵的自身特点,介绍几种可行的轴向力平衡方法,为进一步改进消防泵提供参考。 相似文献