首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 31 毫秒
1.
The study based on pretreatment, hydrolyzation and separation processes with the raw material rice hull, provides a comprehensive utilization of the hydrolyzed productions, such as glucose (C6H12O6) from cellulose, silica (SiO2), and byproduct crystalline sodium sulfate (Na2SO4·10H2O). The optimum hydrolysis conditions are as follows: the concentration of H2SO4 is 72% (wt.%), the temperature is 50 °C, the ratio of H2SO4 solution volume (mL) to the rice hull mass (g) is 10:1 and the time is 5 min, the glucose yield rate reaches 45.6% (wt.%). The concentration of glucose solution could be 0.1 g/mL after neutralization measured by ultraviolet spectrophotometer (UV-VIS). Silica powder was below 50 nm characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The main byproduct crystalline sodium sulfate was featured by XRD and photographs.  相似文献   

2.
The effects of pyrolysis temperature, heating rate, particle size, holding time, and gas flow rate were investigated to optimize bio-oil yield from rice husk pyrolysis. Thermogravimetric analysis showed thermal degradation of hemicellulose, cellulose and lignin, indicating faster decomposition of cellulose compared to lignin. The optimisation process was analysed by employing central composite design (CCD) in response surface methodology (RSM) using Design Expert Version 7.5.1 (StatEase, USA). A two-level fractional factorial was initially carried out and followed by RSM. The statistical analysis showed that pyrolysis temperature, heating rate, particle size and holding time significantly affected the bio-oil yield. By utilising response surface method, these four factors were investigated, analysed and optimal conditions were obtained at pyrolysis temperature of 473.37 °C, heating rate of 100 °C/min, particle size of 0.6 mm and holding time of 1 min. Confirmation runs gave 48.30% and 47.80% of bio-oil yield compared to 48.10% of predicted value. Furthermore, the pyrolytic bio-oils obtained from fixed-bed pyrolysis were examined using gas chromatographic/mass spectroscopy (GC/MS), Fourier transform infrared (FTIR) methods, elemental analyzer, pH probe and bomb calorimeter.  相似文献   

3.
The chemical composition, main physicochemical properties and thermal stability of oil extracted from Acacia senegal seeds were evaluated. The oil, moisture and the ash contents of the seeds were 9.80%, 6.92% and 3.82%, respectively. Physicochemical properties of the oil were iodine value, 106.56 g/100 g of oil; saponification value, 190.23 mg KOH/g of oil; refractive index (25 °C), 1.471; unsaponifiable matter, 0.93%; acidity, 6.41% and peroxide value, 5.43 meq. O2/kg of oil. The main fatty acids in the oil were oleic acid (43.62%) followed by linoleic acid (30.66%) and palmitic acid (11.04%). The triacylglycerols (TAGs) with equivalent carbon number ECN 44 (34.90%) were dominant, followed by TAGs ECN 46 (28.19%), TAGs ECN 42 (16.48%) and TAGs ECN 48 (11.23%). The thermal stability analysed in a normal oxidizing atmosphere showed that the oil decomposition began at 268.6 °C and ended at 618.5 °C, with two stages of decomposition at 401.5 °C and 576.3 °C. According to these results, A. senegal seed oil has physicochemical properties, fatty acids composition and thermal characteristics that may become interesting for specific applications in several segments of food and non-food industries.  相似文献   

4.
The effects of temperature on anatomical and chemical characteristics of Quercus cerris cork were examined. Cork samples were subjected to isothermal air heating between 150 °C and 400 °C and analyzed for mass loss, cellular structure and chemical composition.The thermal decomposition of Q. cerris cork is similar to that of Q. suber cork. Cork is thermally stable below 200 °C and after that degradation depended on temperature and heating time with increasing mass loss, i.e. 3% at 200 °C 10 min and 46% at 350 °C 60 min. With temperature and starting at 200 °C, cells expanded, cell wall thickness was reduced and corrugations were lost.Extractives degraded at lower temperatures, although aliphatic extractives were found to be more stable. Suberin from Q. cerris was more heat resistant than Q. suber suberin, while lignin showed similar resistance.These results provide a basis for studies on the production of Q. cerris bark expanded cork agglomerates for insulation purposes.  相似文献   

5.
The objective of this research was to investigate the wettability and surface roughness properties of the plywood panels under thermal modification. The plywood panel specimens were subjected to thermal modification under atmospheric pressure and presence of air at a temperature of 150, 170 or 190 °C for 60 min. The contact angle measurements were obtained by using a KSV Cam-101 Scientific Instrument connected with a digital camera and computer system. The roughness measurements, average roughness (Ra) and maximum roughness (Rmax), were performed based on both parallel and perpendicular to the grain using a fine stylus tracing technique. Statistical analyses showed significant differences in the surface roughness and contact angle values of the plywood panels following thermal modification.  相似文献   

6.
This work evaluates the use of sugarcane bagasse (SCB) as a source of cellulose to obtain whiskers. These fibers were extracted after SCB underwent alkaline peroxide pre-treatment followed by acid hydrolysis at 45 °C. The influence of extraction time (30 and 75 min) on the properties of the nanofibers was investigated. Sugarcane bagasse whiskers (SCBW) were analyzed by transmission electron microscopy (TEM), X-ray diffraction (XRD) and thermogravimetric analysis (TGA) in air atmosphere. The results showed that SCB could be used as source to obtain cellulose whiskers and they had needle-like structures with an average length (L) of 255 ± 55 nm and diameter (D) of 4 ± 2 nm, giving an aspect ratio (L/D) around 64. More drastic hydrolysis conditions (75 min) resulted in less thermally stable whiskers and caused some damage on the crystal structure of the cellulose as observed by XRD analysis.  相似文献   

7.
Response surface methodology (RSM) was used to optimize the conditions for the production of endo β-1,4 glucanase, a component of cellulase by Aspergillus nidulans MTCC344 under solid state fermentation, using bagasse as the chief substrate. A four-factor-five-level central composite design was employed for experimental design and analysis of the results. Maximum cellulase activity (CMCase was 28.96 U g−1) can be attained at the optimum conditions, 16.8 mm bagasse bed height, 60% moisture content, pH 4.25 and temperature 40 °C in the solid state fermenter. These data were rather close to the experimental results obtained (CMCase was 28.84 U g−1). A. nidulans MTCC344 was able to hydrolyze pretreated bagasse completely after 8 days of incubation with significant endo β-1,4 glucanase activities. The results of Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD) and scanning electron microscopy (SEM) of bagasse showed structural changes through pretreatment, in favor of enzymatic hydrolysis. Bagasse with alkali pretreatment using sodium hydroxide is a source of lignocelluloses able to improve the yield of endo β-1,4 glucanase by the strain of A. nidulans. The endo β-1,4 glucanase produced during the bioconversion of cellulose to glucose by A. nidulans MTCC344 is strongly dependent on the pretreatment given before hydrolysis.  相似文献   

8.
Switchgrass is an important biomass that can be hydrolyzed to yield fermentable sugars through pretreatment, which is the primary and expensive step in conversion of biomass to bio-ethanol. Most of the pretreatment operates in batch mode, which is energy intensive, requires high capital, results in decomposition of hemicellulose, and formation of inhibitors. Considering these shortcomings, a novel biomass pretreatment method using a high shear bioreactor could be a viable continuous one. The current study was undertaken to determine the effect of biomass parameters such as moisture content (10, 20, 30, 40, and 50% wb) and particle size (2, 4, 6, 8, and 10 mm) over a range of barrel temperature and screw speed (45-225 °C and 20-200 rpm). Statistical analyses revealed that among the independent variables considered temperature, screw speed, and moisture content had significant effect on sugar recoveries. Proposed quadratic model to predict glucose, xylose, and combined sugar recoveries from switchgrass had a high F and R2 values indicating that the model has the ability to represent the relationship among the independent variables studied. The optimum pretreatment condition of barrel temperature 176 °C, screw speed 155 rpm, moisture content 20% wb, and particle size 8 mm resulted in maximum glucose, xylose, and combined sugar recoveries of 41.4, 62.2 and 47.4%, respectively. The optimum pretreated switchgrass had 50% higher surface area than that of the control.  相似文献   

9.
Biocomposites derived from polymeric resin and lignocellulosic fibers may be processed at temperatures ranging from 100 °C to 230 °C for durations of up to 30 min. These processing parameters normally lead to the degradation of the fiber's mechanical properties such as Young's modulus (E), ultimate tensile strength (UTS) and percentage elongation at break (%EB). In this study, the effect of processing temperature and duration of heating on the mechanical properties of coir fibers were examined by heating the fibers in an oven at 150 °C and 200 °C for 10, 20 and 30 min to simulate processing conditions. Degradation of mechanical properties was evaluated based on the tensile properties. It was observed that the UTS and %EB of heat treated fibers decreased by 1.17-44.00% and 15.28-81.93%, respectively, compared to untreated fibers. However, the stiffness or E of the fibers increased by 6.3-25.0%. Infra red spectroscopy (FTIR), thermogravimetric analysis (TGA) and scanning electron microscopy (SEM) were used to elucidate further the influence of chemical, thermal and microstructural degradation on the resulting tensile properties of the fibers. The main chemical changes observed at 2922, 2851, 1733, 1651, 1460, 1421 and1370 cm−1 absorption bands were attributed to oxidation, dehydration and depolymerization as well as volatization of the fiber components. These phenomena were also attributed to in the TGA, and in addition the TGA showed increased thermal stability of the heat treated coir fibers with reference to the untreated counterparts which was most probably due to increased recrystallization and cross linking. The microstructural features including microcracks, micropores, collapsed microfibrils and sort of cooled molten liquid observed on the surface of heat treated coir fibers from the scanning electron microscope (SEM) could not directly be linked to the effect of temperature and durations of heating although such features may have largely account for the lower tensile properties of heat treated coir fibers with reference to untreated ones.  相似文献   

10.
Ethanol production by Saccharomyces cerevisiae UFPEDA1238 was performed in simultaneous saccharification and fermentation of delignified sugarcane bagasse. Temperature (32 °C, 37 °C), agitation (80; 100 rpm), enzymatic load (20 FPU/g cellulose and 10%, v/v β-glucosidase or 10 FPU/g cellulose and 5% β-glucosidase) and composition of culture medium were evaluated. Ethanol concentration, enzymatic convertibility of cellulose and volumetric productivity were higher than 25 g/L, 72% and 0.70 g/L h, respectively, after 30 h, when the culture medium 1 and 20 FPU/g cellulose/10%, v/v β-glucosidase or the culture medium 2 and 10 FPU/g cellulose/5% β-glucosidase were used in SSF at 37 °C and 80 rpm. In the SSF with culture medium 2 (supplemented with ammonium, phosphate, potassium and magnesium), 150 L ethanol/t bagasse was achieved, with minimum enzyme loading (10 FPU/g cellulose and 5%, v/v β-glucosidase) for 8%, w/v of solids, which is often an important requirement to provide cost-efficient second generation ethanol processes.  相似文献   

11.
Nanocomposite film composed of bacterial cellulose (10-50 wt.%) and poly-urethane (PU) based resin was fabricated and utilized as a substrate for flexible organic light emitting diode (OLED) display. The performance of the nanocomposite satisfied the criteria for the substrate of OLED with an additional feature of flexibility. The visible light transmittance of the nanocomposite film was as high as 80%. Its thermal stability was stable up to 150 °C while its dimensional stability in terms of coefficient of thermal expansion (CTE) was less than 20 ppm/K. After OLED was fabricated on the substrate through thermal evaporation technique, the OLED performed highest current efficiency of 0.085 cd/A and power efficiency of 0.021 lm/W at 200 cd/m2 while retained its flexible feature, suggesting that bacterial cellulose nanocomposite is a promising material for the development of substrate for flexible OLED display.  相似文献   

12.
The research is concerned with thermochemical characterisation of straws and high yielding perennial grasses. Crops selected for this study include wheat straw (Triticum aestivum), rape straw (Brassica napus), reed canary grass (Phalaris arundinacea) and switch grass (Panicum virgatum). Thermogravimetric analysis (TGA) was used to examine the distribution of char and volatiles during pyrolysis up to 900 °C. Utilising multi-heating rate thermogravimetric data, the Friedman iso-conversional kinetic method was used to determine pyrolysis kinetic parameters. Light and medium volatile decomposition products were investigated using pyrolysis-gas chromatography-mass spectrometry (Py-GC-MS) up to 520 °C. The 22 highest yielding identifiable cellulose, hemicellulose and lignin biomass markers were semi-quantified taking into consideration peak areas from GC chromatograms. Notable differences can be seen in butanedioic acid, dimethyl ester (hemicelluloses decomposition products), 2-methoxy-4-vinylphenol (lignin marker) and levoglucosan (intermediate pyrolytic decomposition product of cellulose) content when comparing perennial grasses with straw. From results presented in this study, perennial grasses such as switch grass, have the most attractive properties for fast pyrolysis processing. This is because of the observed high volatile yield content of 82.23%, heating value of 19.64 MJ/kg and the relatively low inorganic content.  相似文献   

13.
The aim of this study was to evaluate the potential of the fibrous material obtained from ethanol-water fractionation of bagasse as reinforcement of thermoplastic starches in order to improve their mechanical properties. The composites were elaborated using matrices of corn and cassava starches plasticized with 30 wt% glycerin. The mixtures (0, 5, 10 and 15 wt% bagasse fiber) were elaborated in a rheometer at 150 °C. The mixtures obtained were pressed on a hot plate press at 155 °C. The test specimens were obtained according to ASTM D638. Tensile tests, moisture absorption tests for 24 days (20-23 °C and 53% RH, ASTM E104), and dynamic-mechanical analyses (DMA) in tensile mode were carried out. Images by scanning electron microscopy (SEM) and X-ray diffraction were obtained. Fibers (10 wt% bagasse fiber) increased tensile strength by 44% and 47% compared to corn and cassava starches, respectively. The reinforcement (15 wt% bagasse fiber) increased more than fourfold the elastic modulus on starch matrices. The storage modulus at 30 °C (E30 °C′) increased as the bagasse fiber content increased, following the trend of tensile elastic modulus. The results indicate that these fibers have potential applications in the development of biodegradable composite materials.  相似文献   

14.
An ionic liquid (IL)-water mixture employed to treat lignocellulosic biomass is promising. The addition of water decreases viscosity and process cost so as to improve the IL practical application. In this work, effects of temperature (50-170 °C), water content (0-80 wt%), treating duration (0.5-4 h) and pressure (0.1-3.2 MPa) on treating legume straw process using a 1-butyl-3-methylimidazolium chloride ([C4mim]Cl)-water mixture were experimentally investigated. Legume straw was found to be partially dissolved, and the dissolved substances can be flocculated by adding the coagulating agent—water (equal to volume of the solution). For this process at 0.1 MPa, the maximum 29.1 wt% legume straw is dissolved in the [C4mim]Cl-water mixture with water content of 20 wt% at 150 °C during 2 h, which is much higher than 9.8 wt% using pure [C4mim]Cl. A hemicellulose-free lignin-rich material (64.0 wt% lignin and 35.3 wt% cellulose) is obtained by adding the water. Even for 0.5 h, 22.3 wt% of legume straw is dissolved in the case of water content of 20 wt%, 150 °C and 0.1 MPa. High pressure favors the dissolution of legume straw but lignin content in the residue has no obvious change. The addition of proper amount of water facilitates the dissolution of legume straw and a relative rapid dissolving rate can be achieved in a [C4mim]Cl-water mixture. There are great differences in chemical and physical properties between legume straw and the obtained samples (residue and floc) due to the dissolution and reconstitution.  相似文献   

15.
An efficient and environmentally friendly method for the synthesis of cellulose carbamate from a mixture of cellulose pulp or the activated cellulose pulp and urea was presented in this paper. Cellulose carbamate with a nitrogen content of 1.21 % and 3.29 % were successfully synthesized via esterification reaction in the high-boiling aprotic and polar N-methyl-2-pyrrolidone solvents (hereinafter NMP). The structures of cellulose carbamate were characterized by Fourier transform infrared spectroscopy (FTIR), Kjeldahl analysis, thermo-gravimetric analysis, scanning electron microscopy (SEM), X-ray diffractometry (XRD), and 13C-solid-state NMR. The results showed that some functional groups of the alkali cellulose were substituted by amino in the high-boiling aprotic and polar solvents, then the cellulose carbamate was prepared with the reduced crystallinity and thermal decomposition temperature. In addition, the product was prepared with uniform substitution and distribution of carbamate group in the cellulose chain, which guaranteed its good solubility in aqueous alkali as well as its spinnability to produce fiber.  相似文献   

16.
Microcrystalline cellulose (Avicel PH102) and Brewers’ spent grain (BSG) were subjected to Détente Instantanée Contrôlée (DIC) thermomechanical pre-treatment before exposure to cellulases (Celluclast 1.5 L). In a first part, we showed that the addition of β-glucosidase (Novozym-188) increased the hydrolysis yield of Avicel. A maximal theoretical yield (100%), was obtained for 5 and 10 g/L of Avicel using a mixture of Celluclast 1.5 L/Novozym-188. After DIC pre-treatments, the initial rate and final yield of hydrolysis decreased in comparison with those from untreated microcrystalline cellulose. This phenomenon may be due to the modification of the crystallinity of pure cellulose and the formation of inhibitors during the pre-treatment. In a second part, BSG was thermomechanically pre-treated and hydrolyzed. The results showed that the hydrolysis yield of BSG treated at pressure levels between 2 and 7 bar during 15 min was strongly improved compared to hydrolysis yield of untreated BSG. The optimized hydrolysis process, under intensive DIC conditions, achieved a glucose yield corresponding to 100% of the theoretical cellulose value. The morphology of BSG samples was studied with Scanning Electronic Microscopy (SEM) and highlighted that the structure of pre-treated BSG showed an important disruption compared to the rigid structure of untreated BSG.  相似文献   

17.
Autocatalytic hydrothermal process conditions were used to study Ulex europæus (Gorse) as a source of xylan compounds. The aim was to study the possibilities for using this unutilised biomass material to produce xylans. Ulex is an evergreen shrub that grows in the northwest of Spain and has no economic value. Therefore, Ulex is considered a promising candidate as a biomass source. Ulex showed a total xylose content of 12%, thus qualifying it as a suitable material to extract xylan-derived compounds. Autohydrolysis was applied to extract xylans from Ulex. To find the best conditions for xylan extraction, samples of Ulex were subjected to different temperatures and time conditions. Results indicate that autohydrolysis is a suitable method to selectively extract xylans at temperatures between 160 and 190 °C for 5-30 min, reaching a maximum xylan recovery of almost 63% of the initial xylan at 180 °C for 30 min, with only small effects on cellulose and lignin contents.  相似文献   

18.
菠萝叶纤维经过氢氧化钠预处理、硫酸水解制备得到纳米纤维素晶体（NCC）,再用扫描电镜（SEM）、傅立叶转换红外光谱仪（FTIR）、热重（TG）分析仪和X-射线衍射分析仪（XRD）对其结构和性能进行表征和分析。结果表明,NCC晶体颗粒尺寸为30~50 nm;红外光谱证明非纤维素部分有效去除;NCC晶型仍属于纤维素I,结晶度从75.9％提高到87.5％;比起原纤维,NCC的降解温度明显降低。  相似文献   

19.
The steam pre-treatment with low severity preserves valuable biomass components, and further delignification with alkaline peroxide could improve hydrolysis. A combination of low severity steam pretreatment and alkaline peroxide post-treatment of Lespedeza stalks was investigated. The post-treatment of steam-pretreated Lespedeza stalks with alkaline peroxide significantly increased the cellulose content and changed the structure of the cellulose-rich fractions. A glucose yield of 503.5 mg g−1 raw material from enzyme hydrolysis was obtained when the steam-pretreated material (184 °C for 4 min) was post-treated with 2% hydrogen peroxide at 60 °C for 24 h with a substrate concentration of 3.3%. Its hydrolysis yield is 88.8%, which is higher than that of samples processed by steam pretreatment alone (63.7%). The samples obtained by post-treatment with alkaline peroxide were found to have a smoother surface and looser structure in scanning electron microscopy images. The isolated lignin preparations had a yield range from 10.9 to 14.7 (% dry matter). The lignin was characterized by thermogravimetric analysis/differential thermal analysis, Fourier transform infrared spectroscopy, and gel permeation chromatography. Alkaline peroxide treatment increased the thermal stability of lignin, and decreased the amounts of all functional groups. Depolymerization and repolymerization occurred during the alkaline peroxide treatment.  相似文献   

20.
The ability of activated carbon to remove pollutants from water in packed column systems is dependent on granular material with mechanical strength sufficient to avoid attrition caused by stream flow. Therefore, an appropriate balance between surface area and hardness is essential when using activated carbon in real systems. The purpose of this research is to determine the optimal production conditions that generate activated carbon with adequate physical properties to be used in packed systems from agave bagasse, a waste product from the mezcal industries in Mexico. Activated carbons were produced by chemical activation (ZnCl2 or H3PO4). Response surface methodology (RSM) was used to evaluate the effect of the activation temperature (250-550 °C), activation time (0-50 min), and the concentration of activating agent (0.2-1.4; g activating agent/g bagasse) on both surface area and hardness. The production conditions that generated optimal characteristics in the activated carbon were 392 °C, 1.02 g activating agent/g bagasse and 23.8 min for H3PO4 activated samples and 456 °C, 1.08 g activating agent/g bagasse and 23.8 min for ZnCl2 activated samples. The surface area and hardness of the activated carbon produced from bagasse under these conditions were similar to activated commercial carbons (surface area > 800 m2/g and hardness > 85%).  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号