共查询到20条相似文献，搜索用时 292 毫秒
1.
以山西朔州地区的小黑杨人工林为研究材料,研究不同栽植密度(1 000、500、250株·hm-2)对小黑杨木材解剖特性的影响.结果表明:栽植密度对纤维宽度、双壁厚、导管比量、胞壁率、导管个数、导管弦向直径的影响达极显著水平;对壁腔比的影响达显著水平;对纤维长度、长宽比、纤维比量、射线比量虽有一定的影响,但不显著.栽植密度与纤维宽度、导管直径呈负相关关系,与导管个数和比量呈正的相关关系.栽植密度对纤维形态的径向变异有不同程度的影响,但不改变纤维形态变异的一般规律.纤维长度的径向变异为从髓心至树皮向外逐渐增加,到第12 轮达到最大值后略有下降,纤维宽度、长宽比、双壁厚、腔径的径向变异类似于纤维长度;壁腔比的总体径向变异为沿髓心向外,呈先升后降的波动性变异趋势. 相似文献
2.
Yi-Qiang Wu Kazuo Hayashi Yuan Liu Yingchun Cai Masatoshi Sugimori 《Journal of Wood Science》2006,52(3):187-194
To explore the influence of the basic density on collapse-type shrinkage properties and to quantify the relationships of the
main anatomical features with shrinkage and collapse properties, all above-mentioned parameters were determined and analyzed
for three species of collapse-susceptible eucalypts, Eucalyptus urophylla, Eucalyptus grandis, and E. urophylla × E. grandis, planted in South China. The correlation coefficients were also determined and the corresponding regression equations were
established with the anatomical parameters measured by using multiple linear regression. The results indicated that: (1) basic
density was strongly positively linearly related to both unit tangential shrinkage (r = 0.970) and unit radial shrinkage (r = 0.959), weakly positively related to total shrinkage (r = 0.656 and 0.640 for tangential and radial, respectively), and weakly negatively related to residual collapse (r = 0.632 and 0.616 for tangential and radial, respectively). (2) The main factors affecting unit shrinkage were cell wall
proportion (WP), microfibril angle (MFA), and double fiber cell wall thickness (DWT); factors playing an important role in
total shrinkage were WP, ray parenchyma proportion (RP), and MFA, while RP had the highest effect on residual collapse (r = 0.949 and 0.860 for tangential and radial, respectively). (3) All corresponding regression models obtained were very suitable
for the evaluation of relationships between the anatomical parameters and unit shrinkage, total shrinkage, and residual collapse,
as measured using a moisture content of 28% as the fiber saturation point for all specimens. 相似文献
3.
《Wood material science & engineering》2013,8(3):165-173
ABSTRACTIn the present work, Eucalyptus nitens was thermally modified in an open (atmospheric pressure) and a closed (under pressure) reactor system. The effect of the changes of the chemical composition on the mechanical properties was investigated. Hemicelluloses, cellulose, lignin, extractives, acetic acid, formic acid, total phenols and the cellulose degree of polymerization (DP) as well as modulus of elasticity (MOE) and modulus of rupture (MOR) were measured for each modification. The results indicated that the closed system modification, particularly at high pressure, presented stronger variations on the chemical structure of the modified wood than the modifications in the open system. In both modifications, MOR showed a better correlation with the chemical changes than the MOE, especially xylose, cellulose DP, lignin and total phenols. These correlations suggest a tendency of a more brittle wood in the closed system modification at high pressure than in the modifications in the open system. Results can be used as a reference for future applications of thermally modified E. nitens wood. 相似文献
4.
5.
实验观测了青皮竹(Bambusa textilis McClure)和慈竹(B.emeiensis)不同发育期(竹笋、幼竹和成年竹)的解剖特征,包括组织比量、基本组织、维管束及纤维形态的变化。结果表明,随着发育成熟,2个竹种的基本组织比量都呈现下降趋势,而输导组织和纤维组织则呈现不同程度的增长趋势。基本组织的减小量基本上等于纤维组织和输导组织的增加量。在同一发育期慈竹的维管束密度大于青皮竹。纤维长度随着竹龄的增加而变长和增宽,在同一发育期,纤维细胞的直径中部大于基部和顶部。竹子发育期间,纤维直径、双壁厚、长宽比及腔径比都随竹龄增加而增大,壁腔比则呈现下降趋势。2种竹材维管束的径向宽度均大于其弦向宽度。 相似文献
6.
Inter-clonal, intra-clonal and within tree variations in specific gravity and wood anatomical properties of 8-year-old grown
ramets of Dalbergia sissoo Roxb. have been investigated. Radial and location-wise intra-clonal variations were non-significant for anatomical properties
and specific gravity for all six clones at all three sites. However, inter-clonal variations in wood anatomical properties
and specific gravity were significantly different. Inter-clonal variations in anatomical properties and specific gravity were
also significant due to sites, which indicated that site-characteristics overshadowed the genetic priority of different clones
for wood anatomical properties. Average fiber-characteristics of all clones showed the best performance at Lalkuan, Haldwani
(site III), while average specific gravity performed well at Brandis Road, Dehradun (site I) followed by site III (Lalkuan,
Haldwani) and site II (Lachchiwala, Dehradun). Within tree variations in anatomical properties like fiber length, fiber diameter,
wall thickness, vessel member length and vessel member diameter due to vertical or radial direction and location (pith to
periphery) are non-significant. Radial direction, location and height showed no impact on wood element variation. It indicated
that there is no impact of juvenile wood, sapwood and heartwood ratio, and reaction wood on wood anatomical properties of
8-year-old ramet of D. sissoo. It further indicated that clone raised ramet of 8-year-old D. sissoo showed the characteristics of mature wood. Within tree variations in specific gravity were significant due to height, which
may be related to differential sapwood and heartwood ratio in the vertical direction. Different wood elements viz. fiber length,
fiber diameter, wall thickness, vessel member length and vessel member diameter showed significant correlations with each
other and with specific gravity. 相似文献
7.
Wood density, a gross measure of wood mass relative to wood volume, is important in our understanding of stem volume growth, carbon sequestration and leaf water supply. Disproportionate changes in the ratio of wood mass to volume may occur at the level of the whole stem or the individual cell. In general, there is a positive relationship between temperature and wood density of eucalypts, although this relationship has broken down in recent years with wood density decreasing as global temperatures have risen. To determine the anatomical causes of the effects of temperature on wood density, Eucalyptus grandis W. Hill ex Maiden seedlings were grown in controlled-environment cabinets at constant temperatures from 10 to 35 degrees C. The 20% increase in wood density of E. grandis seedlings grown at the higher temperatures was variously related to a 40% reduction in lumen area of xylem vessels, a 10% reduction in the lumen area of fiber cells and a 10% increase in fiber cell wall thickness. The changes in cell wall characteristics could be considered analogous to changes in carbon supply. Lumen area of fiber cells declined because of reduced fiber cell expansion and increased fiber cell wall thickening. Fiber cell wall thickness was positively related to canopy CO2 assimilation rate (Ac), which increased 26-fold because of a 24-fold increase in leaf area and a doubling in leaf CO2 assimilation rate from minima at 10 and 35 degrees C to maxima at 25 and 30 degrees C. Increased Ac increased seedling volume, biomass and wood density; but increased wood density was also related to a shift in partitioning of seedling biomass from roots to stems as temperature increased. 相似文献
8.
Mauricio Ramírez Jaime Rodríguez Miguel Peredo Sofia Valenzuela Regis Mendonça 《Wood Science and Technology》2009,43(1-2):131-141
Variation in wood anatomy and biometric variables was studied in 14 7-year-old Eucalyptus globulus clones grown in a clonal trial in Arauco, Bio-Bio Region, Chile. Biometric characteristics were measured for each tree and the anatomical variables were measured at three radial positions by image analysis on transverse microsections cut from radial increment cores sampled at breast height. Results showed, that among clones wide ranges of variation were found for vessel frequency, vessel area and vessel coverage. However, narrow ranges of variation were found for fiber wall thickness, fiber diameter and lumen diameter. From pith to bark, mean vessel area and vessel coverage increased gradually, whereas the vessel frequency decreased. The fiber wall thickness did not differ significantly from pith to bark. Mean fiber and lumen diameters showed the same radial pattern, increasing from pith to the midpoint of the radius to reach a plateau close to the bark. Furthermore, important commercial volume gains that can exceed 100% were found. Considering the commercial importance of tree volume, vessel and fiber anatomy in the pulping and papermaking process, it is suggested that the information given in this study may be used as an additional criteria for the selection of E. globulus. 相似文献
9.
Katri Luostarinen Katja Hakkarainen Henri Kaksonen 《Scandinavian Journal of Forest Research》2017,32(8):789-797
Soil affects the anatomy of downy birch wood (Betula pubescens), which raises the question whether the growth of this species differs between mineral and peat soils. The aim of this study was to compare growth, density and structure of xylem of B. pubescens between trees grown in different soils. Both growth and density differed between trees grown in different soils. All measured anatomical characteristics, except double thickness of fibre walls, percentage vessel area and ray number, showed differences between the soil types: the cell dimensions were larger and numbers smaller in trees grown in mineral soil. In peat, high growth rates decreased the wall:lumen ratio of fibres in maturing wood, while no such correlation was observed in trees grown in mineral soil at any studied cambial age. In addition, axial parenchyma may have a different role in trees grown in different soils, as the rapid growth decreased and increased axial parenchyma in mineral and peat soil, respectively. The characteristics affecting wood strength were more similar between trees grown in different soils than those affecting water conductance. The observed differences between trees grown in different soils emphasise rapid growth particularly at young ages and shorter reasonable rotation period in mineral soil. 相似文献
10.
对1年生毛白杨人工接种后,毛白杨与瘿瘤木纤维和导管分子长、宽、腔径、长宽比、壁厚与化学组成变异进行测定与分析.结果表明:纤维各解剖参数(壁厚除外)在处理组接种处明显下降,上方木质部和接种处导管变小,下方受其影响较小.方差分析表明:处理组毛白杨木质部木纤维及导管分子差异极显著;对照组木质部木纤维和导管分子无明显变化;瘿瘤之间木纤维及导管分子的长、宽均差异显著,说明瘿瘤细胞分裂异常;与木质部相比,瘿瘤中木纤维和导管分子明显减小;毛白杨木质部和瘿瘤之间木纤维及导管分子差异达显著和极显著.处理组毛白杨接种处冷水抽出物、热水抽出物、1%NaOH抽出物含量增加,纤维素含量降低,木质素含量最高.方差分析表明:处理组毛白杨化学组成变异极显著,对照组毛白杨各接种部位和瘿瘤之间化学组成均变化平稳.瘿瘤木质部中冷水抽出物、热水抽出物、1%NaOH抽出物含量分别比提高了2.6～4.3,1.5～2.6,1.1～1.8倍,而纤维素含量下降了51%～99%,处理组毛白杨接种处木质素含量是瘿瘤的2.7倍,和其他接种部位相比,瘿瘤木质素含量略高. 相似文献
11.
R. V. Rao S. Shashikala P. Sreevani V. Kothiyal C. R. Sarma P. Lal 《Wood Science and Technology》2002,36(3):271-285
Within tree variation in anatomical properties of four and half year old grown Eucalyptus tereticornis Sm. clones have been investigated and correlated with specific gravity. Vessel frequency, vessel diameter and fiber length
were found to vary significantly from bottom to top with no definite trend. Significant variation exists in all the clones
of different parameters. Fiber length was positively correlated with fiber diameter and double wall thickness. Tissue proportions
did not show any significant variation from bottom to top. However, highly significant differences have been found between
clones among four cell types except fibers. Specific gravity is positively correlated with ray percentage, fiber percentage
– vessel percentage ratio and negatively correlated with vessel percentage, while all other anatomical parameters including
height and girth have no effect.
Received 25 August 1998 相似文献
12.
Widyanto Dwi Nugroho Sri Nugroho Marsoem Koh Yasue Takeshi Fujiwara Toshiko Nakajima Masanori Hayakawa Satoshi Nakaba Yusuke Yamagishi Hyun-O Jin Takafumi Kubo Ryo Funada 《Journal of Wood Science》2012,58(3):185-194
The anatomical characteristics and density of wood were examined in 23-year-old Acacia mangium trees that had been planted in Yogyakarta, Indonesia. The seeds had been collected from trees of five different provenances. The distance from the pith of the boundary between juvenile and mature wood was also examined to clarify the maturity of the wood. Lengths of wood fibers near the pith and the distance from the pith of the boundary between juvenile and mature wood differed significantly among provenances. By contrast, other anatomical characteristics of the wood such as fiber wall area, fiber wall thickness, fiber diameter, vessel lumen area, vessel diameter, vessel frequency and wood density did not differ significantly among provenances. Wood density was strongly correlated with the area of fiber walls. Our observations suggest that Sidei and Daintree might be more appropriate provenances among those examined for the Acacia mangium tree-breeding programs in Indonesia that are aimed at improving wood quality, because these provenances are associated with longer initial wood fibers and narrower juvenile areas than the other provenances studied. 相似文献
13.
Futoshi Ishiguri Imam Wahyudi Masae Takeuchi Yuya Takashima Kazuya Iizuka Shinso Yokota Nobuo Yoshizawa 《Journal of Wood Science》2011,57(3):241-246
The relationships between growth characteristics and wood properties were investigated for a threatened species, Pericopsis mooniana, to promote the establishment of plantations of this species in the tropics. Growth characteristics (diameter and height)
and stress-wave velocity (SWV) of trees were measured for 22-year-old P. mooniana trees planted in Indonesia. The trees were categorized into three groups, fast-growing, middle-growing, and slow-growing
trees, to investigate the effect of growth rate on the wood properties. In addition, radial variation of anatomical characteristics
and wood properties were determined. No significant correlation was found between growth characteristics and SWV. The values
for the vessel diameter, cell wall thickness of wood fibers, wood fiber length, basic density, modulus of elasticity, and
modulus of rupture from wood at the bark side were higher than those at the pith side. On the other hand, vessel frequency
gradually decreased from pith to bark. These results suggested that low-quality wood, such as juvenile wood, existed near
the pith area. 相似文献
14.
毛白杨枝条木质部细胞分化的动态变化及其与形成层活动的相互关系 总被引：5，自引：0，他引：5
应用定量解剖学和显微图像分析技术 ,得到了毛白杨枝条形成层细胞与其衍生木质部细胞解剖特征在形成层活动期内的变化情况 ,并探讨了两者之间的关系。采用X射线微密度测定技术 ,了解了同一生长轮内木材密度沿径向方向上的变异 ,讨论了其与木质部细胞解剖特征之间的关系。结果表明 ,形成层纺锤形细胞的径向和弦向宽度在活动期不同阶段差异不显著 ,而纤维长度、纤维宽度、壁腔比、微纤丝角、导管分布频率和胞壁率差异极显著 ;导管组织比量差异显著 ;导管分子长度、纤维比量和射线比量差异不显著。同一生长轮内木材密度的径向变异与活动期不同阶段形成的木质部细胞数量及其解剖特征直接相关。形成层带细胞层数与纤维长度、纤维长宽比和壁腔比呈极显著负相关 ,与纤维宽度呈显著正相关 ;形成层纺锤形细胞的径向宽度与纤维长度、纤维长宽比和射线比量呈显著负相关 ;形成层纺锤形细胞的弦向宽度与纤维宽度呈显著正相关。总体看来 ,在整个形成层活动期 ,形成层纺锤形细胞与木纤维的解剖特征之间随时间变化的相关性较好 ,而与导管分子的相关关系则不明显 相似文献
15.
ZHAO Rongjun FEI Benhua JIANG Zehui Research Institute of Wood Industry Chinese Academy of Forestry Beijing P.R.China 《中国林业科技(英文版)》2007,6(3):33-39
In order to better understand the reasons why eucalypt veneer checks easily and severely, wood samples of three eucalypt species were selected, and their anatomical and physical properties were examined according to conventional methods and the national standards. The effects of variances in cell wall thickness of wood fibre and vessel, and diameter of the cell lumen as well as the tissue ratio on the quality of plywood veneer were analysed. The results show that： 1） There is a great difference in fibre cell wall thickness and diameter of the cell lumen between early wood and late wood of Eucalyptus delegatensis. 2） E. obliqua has a high wood fibre tissue ratio and the thickest fibre cell wall, but the difference inthe fibre cell wall thickness between early wood and late wood is the smallest. 3） The wood fibre tissue ratio of E. regnans is smaller than that of E. obliqua, and its wood fibre cell wall isthe thinnest and there is only a very small difference in fibre cell wall thickness between early wood and late wood. The difference inthe diameter of wood fibre cell lumen among early wood, transition area and late wood is also small： 4） E. delegatensis has the highest tangential shrinkage rate and radial-tangential shrinkage rate, andE. obliqua has the lowest. It is the variability of wood anatomical properties of these species that cause the difference in the veneer shrinkagei and then affects plywood veneer quality. 相似文献
16.
Chang-Hua Fang Daniel Guibal Bruno Clair Joseph Gril Ya-Mei Liu Sheng-Quan Liu 《Annals of Forest Science》2008,65(3):307-307
Six inclined poplar I-69 (Populus deltoids cv. I-69/55) trees were collected for studying the influence of growth stress level on wood properties. Growth stress indicator (GSI) was measured at eight positions around the periphery of each trunk at breast height and corresponding wood samples were obtained. Wood anatomical, physico-mechanical and chemical characteristics were measured, including cell diameter, fibre length, double wall thickness excluding the gelatinous layer, lumen diameter after gelatinous layer removal, proportion of wood tissues, basic density, FSP, MOE, compressive strength, shrinkage and chemical composition. Each property was regarded and discussed in relation to the growth stress level. 相似文献
17.
The structural changes in the cell wall and delignification pattern caused by Trametes versicolor and Trametes hirsuta in the sap wood of Leucaena leucocephala were examined by light and confocal laser scanning microscopy. The in vitro decay test was conducted for 12 weeks. Both species of Trametes used in this study caused anatomical characteristics specific to simultaneous white rot. Formation of boreholes, erosion troughs, erosion channels with U-shaped notches in tangential sections and thinning of cell walls were evident in the wood inoculated with each of the fungal species. Cell separation due to removal of middle lamellae occurred at the early stages of infection (30 d) with T. versicolor. In contrast, middle lamellae remained intact in wood inoculated with T. hirsuta and showed cell separation due to degradation of the outer layer of the secondary wall and degradation of the middle lamellae observed only in severely decayed wood at late stages. Confocal microscopy revealed the delignification pattern particularly from cell corners and vessel walls at an advanced stage of decay, indicating strong ligninolytic activity of both species in the sapwood of L. leucocephala. 相似文献
18.
Cornelia Krause Sergio Rossi Maxime Thibeault-Martel Pierre -Y. Plourde 《Annals of Forest Science》2010,67(4):402-402
19.
Tracheid characteristics ofPicea koraiensis from natural stand in Liangshui area and plantation in Mao'ershan area were studied. The results of variance analysis showed
that the tracheid length, diameter, and thickness of tracheid wall were significant differences between the growth rings.
All those characteristics tend to increase from heart-center to bark. In natural stand, it has positive correlation between
the characteristics. In plantation, the tracheid length has positive correlation with the trachied diameter, while both the
trachied length and the trachied diameter has negative correlation with the thickness of trachied wall. The tracheid length
and diameter have no significant difference in growth between natural stand and plantations. The thickness of tracheid wall
from the plantation is a little thicker than that from the natural stand before 15 years.
Foundation item: This paper was part of State 9th Five-Year Plan project of “Early Mensuration ofPicea koraiensis (nakai)”.
Biography: REN Xu-qin (1973-), female, graduate student in Northeast Forestry University, Harbin 150040, P. R. China.
Responsible editor: Song Funan 相似文献
20.
This study tries to clarify the conflicting results from previous studies on cell wall thickening in bamboo culms by applying light and transmission electron microscopy in combination with image analysis. It focused on both fibre and parenchyma wall thickness of both temperate (Phyllostachys spp.) and tropical (Gigantochloa levis and Dendrocalamus asper) bamboo species of different ages in the light of their suitability for the wood industry. The observations indicated a great heterogeneity in cell wall thickness and cell wall layering pattern of fibres within one culm. Nested design ANOVA’s revealed a rising trend in wall thickness of late maturing fibres and parenchyma cells during the first year but significant wall thickening during later years could not be demonstrated. The high variability within one culm and between culms of the same age from 1 year on is partly masking a clear increased cell wall thickening at higher age. Nevertheless, the highest mean values for fibre wall thickness were recorded in culms of 44 months old or older, suggesting that some kind of late cell wall maturing can take place within one culm. 相似文献