首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 515 毫秒
1.
Oil-in-water (O/W) emulsions containing small oil droplets (d32 approximately 0.22 microm) stabilized by sodium dodecyl sulfate (SDS)-fish gelatin (FG) membranes were produced by an electrostatic deposition technique. A primary emulsion containing anionic SDS-coated droplets (zeta approximately -40 mV) was prepared by homogenizing oil and emulsifier solution using a high-pressure valve homogenizer (20 wt % corn oil, 0.46 wt % SDS, 100 mM acetic acid, pH 3.0). A secondary emulsion containing cationic SDS-FG-coated droplets (zeta approximately +30 mV) was formed by diluting the primary emulsion with an aqueous fish gelatin solution (10 wt % corn oil, 0.23 wt % SDS, 100 mM acetic acid, 2.00 wt % fish gelatin, pH 3.0). The stabilities of primary and secondary emulsions with the same oil concentration to thermal processing, ionic strength, and pH were assessed by measuring particle size distribution, zeta potential, microstructure, destabilized oil, and creaming stability. The droplets in secondary emulsions had good stability to droplet aggregation at holding temperatures from 30 to 90 degrees C for 30 min, [NaCl] < or = 100 mM, and pH values from 3 to 8. This study shows that the ability to generate emulsions containing droplets stabilized by multilayer interfacial membranes comprised of two or more types of emulsifiers, rather than a single interfacial layer comprised of one type of emulsifier, may lead to the development of food products with improved stability to environmental stresses.  相似文献   

2.
Oil-in-water emulsions containing cationic droplets stabilized by lecithin-chitosan membranes were produced using a two-stage process. A primary emulsion containing anionic lecithin-coated droplets was prepared by homogenizing oil and emulsifier solution using a high-pressure valve homogenizer (5 wt % corn oil, 1 wt % lecithin, 100 mM acetic acid, pH 3.0). A secondary emulsion containing cationic lecithin-chitosan-coated droplets was formed by diluting the primary emulsion with an aqueous chitosan solution (1 wt % corn oil, 0.2 wt % lecithin, 100 mM acetic acid, and 0.036 wt % chitosan). The stabilities of the primary and secondary emulsions with the same oil concentration to thermal processing, freeze-thaw cycling, high calcium chloride concentrations, and lipid oxidation were determined. The results showed that the secondary emulsions had better stability to droplet aggregation during thermal processing (30-90 degrees C for 30 min), freeze-thaw cycling (-10 degrees C for 22 h/30 degrees C for 2 h), and high calcium chloride contents (相似文献   

3.
Oil-in-water emulsions containing droplets stabilized by beta-lactoglobulin (beta-Lg)-pectin membranes were produced using a two-stage process. A primary emulsion containing small droplets (d(32) approximately 0.3 microm) was prepared by homogenizing 10 wt % corn oil with 90 wt % aqueous solution (1 wt % beta-Lg, 5 mM imidazole/acetate buffer, pH 3.0) using a high-pressure valve homogenizer. The primary emulsion was then diluted with pectin solutions to produce secondary emulsions with a range of pectin concentrations (5 wt % corn oil, 0.45 wt % beta-Lg, 5 mM imidazole/acetate buffer, 0-0.22 wt % pectin, pH 3.0). The electrical charge on the droplets in the secondary emulsions decreased from +33 +/- 3 to -19 +/- 1 mV as the pectin concentration was increased from 0 to 0.22 wt %, which indicated that pectin adsorbed to the droplet surfaces. The mean particle diameter of the secondary emulsions was small (d(32) < 1 microm) at relatively low pectin concentrations (<0.04 wt %), but increased dramatically at higher pectin concentrations (e.g., d(32) approximately 13 microm at 0.1 wt % pectin), which was attributed to charge neutralization and bridging flocculation effects. Emulsions with relatively small mean particle diameters (d(32) approximately 1.2 microm at 0.1 wt % pectin) could be produced by disrupting flocs formed in secondary emulsions containing highly negatively charged droplets, for example, by sonication, blending, or homogenization. The particles in these emulsions probably consisted of small flocs containing a number of protein-coated droplets bound together by pectin molecules. These emulsions had good stability to further particle aggregation up to relatively high ionic strengths (< or =500 mM NaCl) and low pH (pH 3). The interfacial engineering technology used in this study could lead to the creation of food emulsions with improved physicochemical properties or stability.  相似文献   

4.
Oil-in-water emulsions containing cationic droplets stabilized by lecithin-chitosan membranes were produced using a two-stage process. A primary emulsion was prepared by homogenizing 5 wt % corn oil with 95 wt % aqueous solution (1 wt % lecithin, 100 mM acetic acid, pH 3.0) using a high-pressure valve homogenizer. This emulsion was diluted with aqueous chitosan solutions to form secondary emulsions with varying compositions: 1 wt % corn oil, 0.2 wt % lecithin, 100 mM acetic acid, and 0-0.04 wt % chitosan (pH 3.0). The particle size distribution, particle charge, and creaming stability of the primary and secondary emulsions were measured. The electrical charge on the droplets increased from -49 to +54 mV as the chitosan concentration was increased from 0 to 0.04 wt %, which indicated that chitosan adsorbed to the droplet surfaces. The mean particle diameter of the emulsions increased dramatically and the emulsions became unstable to creaming when the chitosan concentration exceeded 0.008 wt %, which was attributed to charge neutralization and bridging flocculation effects. Sonication, blending, or homogenization could be used to disrupt flocs formed in secondary emulsions containing droplets with high positive charges, leading to the production of emulsions with relatively small particle diameters (approximately 1 microm). These emulsions had good stability to droplet aggregation at low pH (< or =5) and ionic strengths (<500 mM). The interfacial engineering technology utilized in this study could lead to the creation of food emulsions with improved stability to environmental stresses.  相似文献   

5.
The potential of utilizing interfacial complexes, formed through the electrostatic interactions of proteins and polysaccharides at oil-water interfaces, to stabilize model beverage cloud emulsions has been examined. These interfacial complexes were formed by mixing charged polysaccharides with oil-in-water emulsions containing oppositely charged protein-coated oil droplets. Model beverage emulsions were prepared that consisted of 0.1 wt % corn oil droplets coated by beta-lactoglobulin (beta-Lg), beta-Lg/alginate, beta-Lg/iota-carrageenan, or beta-Lg/gum arabic interfacial layers (pH 3 or 4). Stable emulsions were formed when the polysaccharide concentration was sufficient to saturate the protein-coated droplets. The emulsions were subjected to variations in pH (from 3 to 7), ionic strength (from 0 to 250 mM NaCl), and thermal processing (from 30 or 90 degrees C), and the influence on their stability was determined. The emulsions containing alginate and carrageenan had the best stability to ionic strength and thermal processing. This study shows that the controlled formation of protein-polysaccharide complexes at droplet surfaces may be used to produce stable beverage emulsions, which may have important implications for industrial applications.  相似文献   

6.
Interfacial protein-polysaccharide complexes can be used to improve the physical stability of oil-in-water emulsions. The purpose of this study was to examine the impact of ionic strength on the formation and stability of oil-in-water emulsions containing polysaccharide-protein-coated droplets. Emulsions were prepared that contained 0.1 wt % corn oil, 0.05 wt % beta-lactoglobulin, and 0.02 wt % pectin at pH 7. The emulsions were then adjusted to pH 4 to promote electrostatic deposition of the pectin molecules onto the surfaces of the protein-coated droplets. The salt concentration of the aqueous phase (0 or 50 mM NaCl) was adjusted either before or after deposition of the pectin molecules onto the droplet surfaces. We found that stable emulsions containing polysaccharide-protein-coated droplets could be formed when the salt was added after pectin adsorption but not when it was added before pectin adsorption. This phenomenon was attributed to the ability of NaCl to promote droplet flocculation in the protein-coated droplets so that the pectin molecules adsorbed onto the surfaces of flocs rather than individual droplets when salt was added before pectin adsorption. We also found that polysaccharide-protein-coated droplets had a much improved stability to salt-induced flocculation than protein-coated droplets with the same droplet charge (zeta-potential). Theoretical predictions indicated that this was due to the ability of the adsorbed polysaccharide layer to strongly diminish the van der Waals attraction between the droplets.  相似文献   

7.
This study assessed the stabilizing effect of enzymatic cross-linking on double-coated emulsions (beet pectin-fish gelatin). The beet pectin layer was cross-linked via ferulic acid groups using laccase (an enzyme that is known to catalyze the oxidation of phenolic groups). Fish gelatin-coated oil droplets (primary emulsion) were mixed at pH 3.5 to promote electrostatic deposition of the beet pectin molecules onto the surfaces of the oil droplets (secondary emulsion). Laccase was then added to promote cross-linking of the adsorbed beet pectin layer. Cross-linked pectin-coated oil droplets had similar or significantly better stability (p < 0.05) than oil droplets of primary or secondary emulsions to NaCl addition (0-500 mM), CaCl(2) addition (0-250 mM), and thermal processing (30-90 °C for 30 min). Freeze-thaw stability and creaming behavior of enzyme-treated, secondary emulsions after two cycles (-8 °C for 22 h; 25 °C for 2 h) were significantly improved (p < 0.05). These results may have important implications for food manufacturers that are in need of emulsions with improved physical stability, for example, emulsions used in frozen foods for sauces or dips.  相似文献   

8.
The purpose of this study was to create water-in-oil (W/O) and water-in-oil-in-water (W/O/W) emulsions containing gelled internal water droplets. Twenty weight percent W/O emulsions stabilized by a nonionic surfactant (6.4 wt % polyglycerol polyricinoleate, PGPR) were prepared that contained either 0 or 15 wt % whey protein isolate (WPI) in the aqueous phase, with the WPI-containing emulsions being either unheated or heated (80 degrees C for 20 min) to gel the protein. Optical microscopy and sedimentation tests did not indicate any significant changes in droplet characteristics of the W/O emulsions depending on WPI content (0 or 15%), shearing (0-7 min at constant shear), thermal processing (30-90 degrees C for 30 min), or storage at room temperature (up to 3 weeks). W/O/W emulsions were produced by homogenizing the W/O emulsions with an aqueous Tween 20 solution using either a membrane homogenizer (MH) or a high-pressure valve homogenizer (HPVH). For the MH the mean oil droplet size decreased with increasing number of passes, whereas for the HPVH it decreased with increasing number of passes and increasing homogenization pressure. The HPVH produced smaller droplets than the MH, but the MH produced a narrower particle size distribution. All W/O/W emulsions had a high retention of water droplets (>95%) within the larger oil droplets after homogenization. This study shows that W/O/W emulsions containing oil droplets with gelled water droplets inside can be produced by using MH or HPVH.  相似文献   

9.
The ability of two protein fractions extracted from cod to form and stabilize oil-in-water emulsions was examined: a high salt extracted fraction (HSE protein) and a pH 3 acid extracted fraction (AE protein). Both fractions consisted of a complex mixture of different proteins, with the predominant one being myosin (200 kDa). The two protein fractions were used to prepare 5 wt % corn oil-in-water emulsions at ambient temperature (pH 3.0, 10 mM citrate-imidazole buffer). Emulsions with relatively small mean droplet diameters (d(3,2) < 1 microm) and good creaming stability (> 9 days) could be produced at protein concentrations > or =0.2 wt % for both fractions. The isoelectric point of droplets stabilized by both protein fractions was pH approximately 5. The emulsions were stable to droplet flocculation and creaming at relatively low pH (< or =4) and NaCl concentrations (< or =150 mM) when stored at room temperature. In the absence of salt, the emulsions were also stable to thermal treatment (30-90 degrees C for 30 min), but in the presence of 100 mM NaCl droplet flocculation and creaming were observed in some of the emulsions, particularly those stabilized by the AE fraction. The results suggest that protein fractions extracted from cod can be used as emulsifiers to form and stabilize food emulsions.  相似文献   

10.
Protein fractions were isolated from coconut: coconut skim milk protein isolate (CSPI) and coconut skim milk protein concentrate (CSPC). The ability of these proteins to form and stabilize oil-in-water emulsions was compared with that of whey protein isolate (WPI). The solubility of the proteins in CSPI, CSPC, and WPI was determined in aqueous solutions containing 0, 100, and 200 mM NaCl from pH 3 to 8. In the absence of salt, the minimum protein solubility occurred between pH 4 and 5 for CSPI and CSPC and around pH 5 for WPI. In the presence of salt (100 and 200 mM NaCl), all proteins had a higher solubility than in distilled water. Corn oil-in-water emulsions (10 wt %) with relatively small droplet diameters (d32 approximately 0.46, 1.0, and 0.5 mum for CSPI, CSPC, and WPI, respectively) could be produced using 0.2 wt % protein fraction. Emulsions were prepared with different pH values (3-8), salt concentrations (0-500 mM NaCl), and thermal treatments (30-90 degrees C for 30 min), and the mean particle diameter, particle size distribution, zeta-potential, and creaming stability were measured. Considerable droplet flocculation occurred in the emulsions near the isoelectric point of the proteins: CSPI, pH approximately 4.0; CSPC, pH approximately 4.5; WPI, pH approximately 4.8. Emulsions with monomodal particle size distributions, small mean droplet diameters, and good creaming stability could be produced at pH 7 for CSPI and WPI, whereas CSPC produced bimodal distributions. The CSPI and WPI emulsions remained relatively stable to droplet aggregation and creaming at NaCl concentrations of < or =50 and < or =100 mM, respectively. In the absence salt, the CSPI and WPI emulsions were also stable to thermal treatments at < or =80 and < or =90 degrees C for 30 min, respectively. These results suggest that CSPI may be suitable for use as an emulsifier in the food industry.  相似文献   

11.
Oil-in-water emulsions (4 wt % soy oil) containing 4 wt % whey protein hydrolysate (WPH) (27% degree of hydrolysis) and different levels of calcium, magnesium, or potassium chloride were prepared in a two-stage homogenizer. Other emulsions containing 4 wt % WPH but including 0.35 wt % hydroxylated lecithin and different levels of the above minerals were similarly prepared. The formation and stability of these emulsions were determined by measuring oil droplet size distributions using laser light scattering and by confocal scanning laser microscopy and a gravity creaming test. Both lecithin-free and lecithin-containing emulsions showed no change in droplet size distributions with increasing concentration of potassium in the range 0-37.5 mM. In contrast, the diameter of emulsion droplets increased with increasing calcium or magnesium concentration >12.5 mM. Emulsions containing hydroxylated lecithin were more sensitive to the addition of calcium or magnesium than the lecithin-free emulsions. Storage of emulsions at 20 degrees C for 24 h further increased the diameter of droplets and resulted in extensive creaming in emulsions containing >25 mM calcium or magnesium. It appears that both flocculation and coalescence processes were involved in the destabilization of emulsions induced by the addition of divalent cations.  相似文献   

12.
Soybeans contain oil bodies that are coated by a layer of oleosin proteins. In nature, this protein coating protects the oil bodies from environmental stresses and may be utilized by food manufacturers for the same purpose. In this study, oil bodies were extracted from soybean using an aqueous extraction method that involved blending, dispersion (pH 8.6), filtration, and centrifugation steps. The influence of NaCl (0-250 mM), thermal processing (30-90 degrees C, 20 min) and pH (2-8) on the properties and stability of the oil bodies was analyzed using zeta-potential, particle size, and creaming stability measurements. The extracted oil bodies were relatively small ( d 32 approximately 250 nm), and their zeta-potential went from around +12 mV to -20 mV as the pH was increased from 2 to 8, with an isoelectric point around pH 4. The oil bodies were stable to aggregation and creaming at low (pH = 2) and high (pH >/= 6) pH values but were unstable at intermediate values (3 相似文献   

13.
The properties of whey protein isolate (WPI) stabilized oil-in-water (O/W) nanoemulsions (d(43) ≈ 66 nm; 0.5% oil, 0.9% WPI) and emulsions (d(43) ≈ 325 nm; 0.5% oil, 0.045% WPI) were compared. Emulsions were prepared by high-pressure homogenization, while nanoemulsions were prepared by high-pressure homogenization and solvent (ethyl acetate) evaporation. The effects of pH, ionic strength (0-500 mM NaCl), thermal treatment (30-90 °C), and freezing/thawing on the stability and properties of the nanoemulsions and emulsions were compared. In general, nanoemulsions had better stability to droplet aggregation and creaming than emulsions. The nanoemulsions were unstable to droplet flocculation near the isoelectric point of WPI but remained stable at higher or lower pH values. In addition, the nanoemulsions were stable to salt addition, thermal treatment, and freezing/thawing (pH 7). Lipid oxidation was faster in nanoemulsions than emulsions, which was attributed to the increased surface area. Lipase digestibility of lipids was slower in nanoemulsions than emulsions, which was attributed to changes in interfacial structure and protein content. These results have important consequences for the design and utilization of food-grade nanoemulsions.  相似文献   

14.
The influence of chelating agents (disodium ethylenediaminetetraacetate (EDTA) and sodium citrate) on the physicochemical properties of whey protein isolate (WPI)-stabilized oil-in-water emulsions containing calcium chloride was determined. The calcium-binding characteristics of EDTA and citrate at 30 degrees C were characterized in aqueous solutions (20 mM Tris buffer, pH 7.0) by isothermal titration calorimetry (ITC). EDTA and citrate both bound calcium ions in a 1:1 ratio, but EDTA had a much higher binding constant. Oil-in-water emulsions (pH 7.0) were prepared containing 6.94% (w/v) soybean oil, 0.35% (w/v) WPI, 0.02% (w/v) sodium azide, 20 mM Tris buffer, 10 mM CaCl(2), and 0-40 mM chelating agent. The particle size, apparent viscosity, creaming stability, free calcium concentration, and particle surface potential of the emulsions were measured. The chelating agents reduced or prevented droplet aggregation in the emulsions. When they were present above a certain concentration (>3.5 mM EDTA or >5 mM citrate), droplet aggregation was prevented. The reduction of aggregation was indicated by decreases in particle size, shear-thinning behavior, apparent viscosity, and creaming. Emulsions containing chelating agents had lower free calcium concentrations and more negatively charged droplets, indicating that the chelating agents improved emulsion stability by binding calcium ions. EDTA could be used at lower concentrations than citrate because of its higher calcium ion binding constant.  相似文献   

15.
To obtain a better understanding of how the interfacial region of emulsion droplets influences lipid oxidation, the oxidative stability of salmon oil-in-water emulsions stabilized by whey protein isolate (WPI), sweet whey (SW), beta-lactoglobulin (beta-Lg), or alpha-lactalbumin (alpha-La) was evaluated. Studies on the influence of pH on lipid oxidation in WPI-stabilized emulsions showed that formation of lipid hydroperoxides and headspace propanal was much lower at pH values below the protein's isoelectric point (pI), at which the emulsion droplets were positively charged, compared to that at pH values above the pI, at which the emulsion droplets were negatively charged. This effect was likely due to the ability of positively charged emulsion droplets to repel cationic iron. In a comparison of lipid oxidation rates of WPI-, SW-, beta-Lg-, and alpha-La-stabilized emulsions at pH 3, the oxidative stability was in the order of beta-Lg > or = SW > alpha-La > or = WPI. The result indicated that it was possible to engineer emulsions with greater oxidative stability by using proteins as emulsifier, thereby reducing or eliminating the need for exogenous food antioxidants.  相似文献   

16.
Emulsion can be produced with electrostatic layer-by-layer deposition technologies to have cationic, thick multilayer interfacial membranes that are effective at inhibiting the oxidation of omega-3 fatty acids. This study investigated the stability of spray-dried multilayer emulsion upon reconstitution into an aqueous system. The primary (lecithin) and multilayered secondary emulsions (lecithin and chitosan) were spray-dried with corn syrup solids (1-20 wt %). The lecithin-chitosan multilayer interfacial membrane remained intact on the emulsion droplets upon reconstitution into an aqueous system. Reconstituted secondary (lecithin-chitosan) emulsions were more oxidatively stable than reconstituted primary (lecithin) emulsions. A minimum of 5 wt % corn syrup solids was needed to microencapsulate the secondary emulsion droplets. Maximum oxidative stability of both the powder and the reconstituted secondary emulsions was observed in samples with 5% and 20% corn syrup solids. Addition of EDTA (25 microM) inhibited oxidation of reconstituted primary and secondary emulsions. These studies suggest that a microencapsulated multilayered emulsion system could be used as a delivery system for omega-3 fatty acids in functional foods.  相似文献   

17.
The influence of pH and iota-carrageenan concentration on the properties of beta-lactoglobulin (beta-Lg)-stabilized oil-in-water emulsions was investigated by measuring the particle charge, particle size distribution, and creaming stability. Emulsions containing droplets stabilized by beta-Lg were produced by homogenization, and then, iota-carrageenan was added. At pH 3, the droplet charge did not change for iota-carrageenan concentrations 相似文献   

18.
Catastrophic phase inversion (CPI) was used as a low-energy emulsification method to prepare oil-in-water (O/W) nanoemulsions in a lipid (Acetem)/water/nonionic surfactant (Tween 60) system. CPIs in which water-in-oil emulsions (W/O) are transformed into oil-in-water emulsions (O/W) were induced by changes in the phase ratio. Dynamic phase inversion emulsification was achieved by slowly increasing the water volume fraction (fw) to obtain O/W emulsions from water in oil emulsions. Composition and processing variables were optimized to minimize droplet size and polydispersity index (PdI). It was found that addition of the continuous phase to the dispersed phase following the standard CPI procedure resulted in the formation of oil droplets with diameters of 100-200 nm. Droplet size distribution during CPI and emulsification time depended on stirring speed and surfactant concentration. Droplet sizes in the inverted emulsions were compared to those obtained by direct emulsification: The process time to reach droplet sizes of around 100 nm was reduced by 12 times by using CPI emulsification. The Acetem/water nanoemulsion was also used as a carrier to incorporate oregano and cinnamon essential oils into soy protein edible films. The resulting composite films containing oregano oil showed better moisture barrier and mechanical properties compared to soy protein films.  相似文献   

19.
Polysaccharides are widely used in the food industry to modify the stability of protein-based drinks. However, an in depth knowledge of the interactions occurring in the system is still lacking. In this study, the interactions between sodium caseinate and high methoxyl pectin under acidification conditions were studied nondestructively and without dilution using transmission diffusing wave spectroscopy. Oil-in-water emulsions were prepared with 10% soybean oil and 0.5% sodium caseinate. Various concentrations of pectin (ranging from 0 to 0.2%) were added, and the emulsions were acidified with glucono-delta-lactone. With acidification, a "sol-gel" transition occurred and emulsions containing pectin were more stable at lower pH than those without pectin. Furthermore, the sol-gel transition of the mixtures was more sudden for control emulsions without pectin. While in control samples the final solidlike emulsion after gelation tended to be more inhomogeneous and more dissimilar to the starting emulsion, emulsions with pectin in solution gelled later under acidification. With a sufficient amount of pectin, the emulsions showed no aggregation and the destabilization pH varied depending on the amount of pectin present in the emulsions. At intermediate pH values (pH > 5.5), the emulsions displayed a decrease in particle size, more pronounced in samples containing pectin. The results collected using light scattering in concentrated systems, 10% (v/v) in our case, suggested that pectin stabilizes the emulsion oil droplets forming a network of oil droplets loosely connected by strands of pectin.  相似文献   

20.
The influence of sucrose (0-40 wt %) on the thermal denaturation and functionality of whey protein isolate (WPI) solutions has been studied. The effect of sucrose on the heat denaturation of 0.2 wt % WPI solutions (pH 7.0) was measured using differential scanning calorimetry. Sucrose increased the temperature at which protein denaturation occurred, for example, by 6-8 degrees C for 40 wt % sucrose. The dynamic shear rheology of 10 wt % WPI solutions (pH 7.0, 100 mM NaCl) was monitored as they were heated from 30 to 90 degrees C and then cooled to 30 degrees C. Sucrose increased the gelation temperature and the final rigidity of the cooled gels. The degree of flocculation in 10 wt % oil-in-water emulsions stabilized by 1 wt % WPI (pH 7.0, 100 mM NaCl) was measured using a light scattering technique after they were heated at fixed temperatures from 30 to 90 degrees C for 15 min and then cooled to 30 degrees C. Sucrose increased the temperature at which maximum flocculation was observed and increased the extent of droplet flocculation. These results are interpreted in terms of the influence of sucrose on the thermal unfolding and aggregation of protein molecules.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号