首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 922 毫秒
1.
Oil-in-water emulsions containing cationic droplets stabilized by lecithin-chitosan membranes were produced using a two-stage process. A primary emulsion was prepared by homogenizing 5 wt % corn oil with 95 wt % aqueous solution (1 wt % lecithin, 100 mM acetic acid, pH 3.0) using a high-pressure valve homogenizer. This emulsion was diluted with aqueous chitosan solutions to form secondary emulsions with varying compositions: 1 wt % corn oil, 0.2 wt % lecithin, 100 mM acetic acid, and 0-0.04 wt % chitosan (pH 3.0). The particle size distribution, particle charge, and creaming stability of the primary and secondary emulsions were measured. The electrical charge on the droplets increased from -49 to +54 mV as the chitosan concentration was increased from 0 to 0.04 wt %, which indicated that chitosan adsorbed to the droplet surfaces. The mean particle diameter of the emulsions increased dramatically and the emulsions became unstable to creaming when the chitosan concentration exceeded 0.008 wt %, which was attributed to charge neutralization and bridging flocculation effects. Sonication, blending, or homogenization could be used to disrupt flocs formed in secondary emulsions containing droplets with high positive charges, leading to the production of emulsions with relatively small particle diameters (approximately 1 microm). These emulsions had good stability to droplet aggregation at low pH (< or =5) and ionic strengths (<500 mM). The interfacial engineering technology utilized in this study could lead to the creation of food emulsions with improved stability to environmental stresses.  相似文献   

2.
Oil-in-water emulsions containing cationic droplets stabilized by lecithin-chitosan membranes were produced using a two-stage process. A primary emulsion containing anionic lecithin-coated droplets was prepared by homogenizing oil and emulsifier solution using a high-pressure valve homogenizer (5 wt % corn oil, 1 wt % lecithin, 100 mM acetic acid, pH 3.0). A secondary emulsion containing cationic lecithin-chitosan-coated droplets was formed by diluting the primary emulsion with an aqueous chitosan solution (1 wt % corn oil, 0.2 wt % lecithin, 100 mM acetic acid, and 0.036 wt % chitosan). The stabilities of the primary and secondary emulsions with the same oil concentration to thermal processing, freeze-thaw cycling, high calcium chloride concentrations, and lipid oxidation were determined. The results showed that the secondary emulsions had better stability to droplet aggregation during thermal processing (30-90 degrees C for 30 min), freeze-thaw cycling (-10 degrees C for 22 h/30 degrees C for 2 h), and high calcium chloride contents (相似文献   

3.
Oil-in-water (O/W) emulsions containing small oil droplets (d32 approximately 0.22 microm) stabilized by sodium dodecyl sulfate (SDS)-fish gelatin (FG) membranes were produced by an electrostatic deposition technique. A primary emulsion containing anionic SDS-coated droplets (zeta approximately -40 mV) was prepared by homogenizing oil and emulsifier solution using a high-pressure valve homogenizer (20 wt % corn oil, 0.46 wt % SDS, 100 mM acetic acid, pH 3.0). A secondary emulsion containing cationic SDS-FG-coated droplets (zeta approximately +30 mV) was formed by diluting the primary emulsion with an aqueous fish gelatin solution (10 wt % corn oil, 0.23 wt % SDS, 100 mM acetic acid, 2.00 wt % fish gelatin, pH 3.0). The stabilities of primary and secondary emulsions with the same oil concentration to thermal processing, ionic strength, and pH were assessed by measuring particle size distribution, zeta potential, microstructure, destabilized oil, and creaming stability. The droplets in secondary emulsions had good stability to droplet aggregation at holding temperatures from 30 to 90 degrees C for 30 min, [NaCl] < or = 100 mM, and pH values from 3 to 8. This study shows that the ability to generate emulsions containing droplets stabilized by multilayer interfacial membranes comprised of two or more types of emulsifiers, rather than a single interfacial layer comprised of one type of emulsifier, may lead to the development of food products with improved stability to environmental stresses.  相似文献   

4.
The influence of chelating agents (disodium ethylenediaminetetraacetate (EDTA) and sodium citrate) on the physicochemical properties of whey protein isolate (WPI)-stabilized oil-in-water emulsions containing calcium chloride was determined. The calcium-binding characteristics of EDTA and citrate at 30 degrees C were characterized in aqueous solutions (20 mM Tris buffer, pH 7.0) by isothermal titration calorimetry (ITC). EDTA and citrate both bound calcium ions in a 1:1 ratio, but EDTA had a much higher binding constant. Oil-in-water emulsions (pH 7.0) were prepared containing 6.94% (w/v) soybean oil, 0.35% (w/v) WPI, 0.02% (w/v) sodium azide, 20 mM Tris buffer, 10 mM CaCl(2), and 0-40 mM chelating agent. The particle size, apparent viscosity, creaming stability, free calcium concentration, and particle surface potential of the emulsions were measured. The chelating agents reduced or prevented droplet aggregation in the emulsions. When they were present above a certain concentration (>3.5 mM EDTA or >5 mM citrate), droplet aggregation was prevented. The reduction of aggregation was indicated by decreases in particle size, shear-thinning behavior, apparent viscosity, and creaming. Emulsions containing chelating agents had lower free calcium concentrations and more negatively charged droplets, indicating that the chelating agents improved emulsion stability by binding calcium ions. EDTA could be used at lower concentrations than citrate because of its higher calcium ion binding constant.  相似文献   

5.
The influence of weighting agents and sucrose on gravitational separation in 1 wt % oil-in-water emulsions was studied by measuring changes in the intensity of backscattered light from the emulsions with height. Emulsions with different droplet densities were prepared by mixing weighting agents [brominated vegetable oil (BVO), ester gum (EG), damar gum (DG), or sucrose acetate isobutyrate (SAIB)] with soybean oil prior to homogenization. Sedimentation or creaming occurred when the droplet density was greater than or lower than the aqueous phase density, respectively. The weighting agent concentrations required to match the oil and aqueous phase densities were 25 wt % BVO, 55 wt % EG, 55 wt % DG, and 45 wt % SAIB. The efficiency of droplet reduction during homogenization also depended on weighting agent type (BVO > SAIB > DG, EG) due to differences in oil phase viscosity. The influence of sucrose (0-13 wt %) on the creaming stability of 1 wt % soybean oil-in-water emulsions was also examined. Sucrose increased the aqueous phase viscosity (retarding creaming) and increased the density contrast between droplets and aqueous phase (accelerating creaming). These two effects largely canceled one another so that the creaming stability was relatively insensitive to sucrose concentration.  相似文献   

6.
The possibility of producing stable oil-in-water (O/W) emulsions containing oil droplets surrounded by multiple layer interfacial membranes from food grade ingredients has been demonstrated. These emulsions were produced using a three stage process that relies on the adsorption of charged biopolymers to oppositely charged surfaces. Emulsions (0.5 wt % corn oil, 0.1 wt % lecithin, 0.0078 wt % chitosan, 0.02 wt % pectin, and 100 mM acetic acid, pH 3.0) containing oil droplets stabilized by lecithin-chitosan-pectin membranes were formed using this interfacial layer-by-layer deposition process. The droplets in these emulsions had good stability to aggregation over a wide range of pH values and salt concentrations (pH 4-8 at 0 mM NaCl and pH 3-8 at 100 mM NaCl). This technology could be extremely useful to the food industry for the creation of O/W emulsions with improved properties or novel applications, e.g., improved stability to environmental stresses, protection of labile substances, controlled release, and triggered release.  相似文献   

7.
The influence of pH and iota-carrageenan concentration on the properties of beta-lactoglobulin (beta-Lg)-stabilized oil-in-water emulsions was investigated by measuring the particle charge, particle size distribution, and creaming stability. Emulsions containing droplets stabilized by beta-Lg were produced by homogenization, and then, iota-carrageenan was added. At pH 3, the droplet charge did not change for iota-carrageenan concentrations 相似文献   

8.
The ability of two protein fractions extracted from cod to form and stabilize oil-in-water emulsions was examined: a high salt extracted fraction (HSE protein) and a pH 3 acid extracted fraction (AE protein). Both fractions consisted of a complex mixture of different proteins, with the predominant one being myosin (200 kDa). The two protein fractions were used to prepare 5 wt % corn oil-in-water emulsions at ambient temperature (pH 3.0, 10 mM citrate-imidazole buffer). Emulsions with relatively small mean droplet diameters (d(3,2) < 1 microm) and good creaming stability (> 9 days) could be produced at protein concentrations > or =0.2 wt % for both fractions. The isoelectric point of droplets stabilized by both protein fractions was pH approximately 5. The emulsions were stable to droplet flocculation and creaming at relatively low pH (< or =4) and NaCl concentrations (< or =150 mM) when stored at room temperature. In the absence of salt, the emulsions were also stable to thermal treatment (30-90 degrees C for 30 min), but in the presence of 100 mM NaCl droplet flocculation and creaming were observed in some of the emulsions, particularly those stabilized by the AE fraction. The results suggest that protein fractions extracted from cod can be used as emulsifiers to form and stabilize food emulsions.  相似文献   

9.
The objective of this study was to examine the effects of added xanthan gum, guar gum, or kappa-carrageenan on the formation and properties of emulsions (4 wt % corn oil) formed with an extensively hydrolyzed commercial whey protein (WPH) product under a range of conditions. The rate of coalescence was calculated on the basis of the changes in the droplet size of emulsions during storage of the emulsions at 20 degrees C. Compared with the emulsion made without the addition of polysaccharides, the rate of creaming and coalescence in emulsions containing xanthan gum, guar gum, or kappa-carrageenan was markedly enhanced with increasing concentration of polysaccharides during storage for up to 7 days. At a given concentration, the rate of coalescence was highest in the emulsions containing guar gum, whereas it was lowest in the emulsions containing kappa-carrageenan. All emulsions containing xanthan gum, guar gum, or kappa-carrageenan showed flocculation of oil droplets by a depletion mechanism. This flocculation was considered to enhance the coalescence of oil droplets. The different rates of coalescence could be explained on the basis of the strength of the depletion potential, which was dependent on the molecular weight and the radius of gyration of the polysaccharides.  相似文献   

10.
Oil-in-water emulsions containing droplets stabilized by beta-lactoglobulin (beta-Lg)-pectin membranes were produced using a two-stage process. A primary emulsion containing small droplets (d(32) approximately 0.3 microm) was prepared by homogenizing 10 wt % corn oil with 90 wt % aqueous solution (1 wt % beta-Lg, 5 mM imidazole/acetate buffer, pH 3.0) using a high-pressure valve homogenizer. The primary emulsion was then diluted with pectin solutions to produce secondary emulsions with a range of pectin concentrations (5 wt % corn oil, 0.45 wt % beta-Lg, 5 mM imidazole/acetate buffer, 0-0.22 wt % pectin, pH 3.0). The electrical charge on the droplets in the secondary emulsions decreased from +33 +/- 3 to -19 +/- 1 mV as the pectin concentration was increased from 0 to 0.22 wt %, which indicated that pectin adsorbed to the droplet surfaces. The mean particle diameter of the secondary emulsions was small (d(32) < 1 microm) at relatively low pectin concentrations (<0.04 wt %), but increased dramatically at higher pectin concentrations (e.g., d(32) approximately 13 microm at 0.1 wt % pectin), which was attributed to charge neutralization and bridging flocculation effects. Emulsions with relatively small mean particle diameters (d(32) approximately 1.2 microm at 0.1 wt % pectin) could be produced by disrupting flocs formed in secondary emulsions containing highly negatively charged droplets, for example, by sonication, blending, or homogenization. The particles in these emulsions probably consisted of small flocs containing a number of protein-coated droplets bound together by pectin molecules. These emulsions had good stability to further particle aggregation up to relatively high ionic strengths (< or =500 mM NaCl) and low pH (pH 3). The interfacial engineering technology used in this study could lead to the creation of food emulsions with improved physicochemical properties or stability.  相似文献   

11.
Interfacial protein-polysaccharide complexes can be used to improve the physical stability of oil-in-water emulsions. The purpose of this study was to examine the impact of ionic strength on the formation and stability of oil-in-water emulsions containing polysaccharide-protein-coated droplets. Emulsions were prepared that contained 0.1 wt % corn oil, 0.05 wt % beta-lactoglobulin, and 0.02 wt % pectin at pH 7. The emulsions were then adjusted to pH 4 to promote electrostatic deposition of the pectin molecules onto the surfaces of the protein-coated droplets. The salt concentration of the aqueous phase (0 or 50 mM NaCl) was adjusted either before or after deposition of the pectin molecules onto the droplet surfaces. We found that stable emulsions containing polysaccharide-protein-coated droplets could be formed when the salt was added after pectin adsorption but not when it was added before pectin adsorption. This phenomenon was attributed to the ability of NaCl to promote droplet flocculation in the protein-coated droplets so that the pectin molecules adsorbed onto the surfaces of flocs rather than individual droplets when salt was added before pectin adsorption. We also found that polysaccharide-protein-coated droplets had a much improved stability to salt-induced flocculation than protein-coated droplets with the same droplet charge (zeta-potential). Theoretical predictions indicated that this was due to the ability of the adsorbed polysaccharide layer to strongly diminish the van der Waals attraction between the droplets.  相似文献   

12.
Protein fractions were isolated from coconut: coconut skim milk protein isolate (CSPI) and coconut skim milk protein concentrate (CSPC). The ability of these proteins to form and stabilize oil-in-water emulsions was compared with that of whey protein isolate (WPI). The solubility of the proteins in CSPI, CSPC, and WPI was determined in aqueous solutions containing 0, 100, and 200 mM NaCl from pH 3 to 8. In the absence of salt, the minimum protein solubility occurred between pH 4 and 5 for CSPI and CSPC and around pH 5 for WPI. In the presence of salt (100 and 200 mM NaCl), all proteins had a higher solubility than in distilled water. Corn oil-in-water emulsions (10 wt %) with relatively small droplet diameters (d32 approximately 0.46, 1.0, and 0.5 mum for CSPI, CSPC, and WPI, respectively) could be produced using 0.2 wt % protein fraction. Emulsions were prepared with different pH values (3-8), salt concentrations (0-500 mM NaCl), and thermal treatments (30-90 degrees C for 30 min), and the mean particle diameter, particle size distribution, zeta-potential, and creaming stability were measured. Considerable droplet flocculation occurred in the emulsions near the isoelectric point of the proteins: CSPI, pH approximately 4.0; CSPC, pH approximately 4.5; WPI, pH approximately 4.8. Emulsions with monomodal particle size distributions, small mean droplet diameters, and good creaming stability could be produced at pH 7 for CSPI and WPI, whereas CSPC produced bimodal distributions. The CSPI and WPI emulsions remained relatively stable to droplet aggregation and creaming at NaCl concentrations of < or =50 and < or =100 mM, respectively. In the absence salt, the CSPI and WPI emulsions were also stable to thermal treatments at < or =80 and < or =90 degrees C for 30 min, respectively. These results suggest that CSPI may be suitable for use as an emulsifier in the food industry.  相似文献   

13.
The interactions of proteins during the heat treatment of whey-protein-isolate (WPI)-based oil-in-water emulsions with and without added hydroxylated lecithin were studied by examining the changes in droplet size distribution and the quantity and type of adsorbed and unadsorbed proteins. Heat treatment at 90 degrees C of WPI emulsions resulted in an increase in total adsorbed protein; unadsorbed beta-lactoglobulin (beta-lg) was the main protein interacting with the adsorbed proteins during the first 10 min of heating, but after this time, unadsorbed alpha-lactalbumin (alpha-la) also associated with the adsorbed protein. In emulsions containing hydroxylated lecithin, the increase in total adsorbed protein during heat treatment was much lower and the unadsorbed beta-lg did not appear to interact with the adsorbed proteins during heating. However, the behavior of alpha-la during heat treatment of these emulsions was similar to that observed in the emulsions containing no hydroxylated lecithin. In the presence of NaCl, the particle size of the emulsion droplets and the quantities of adsorbed protein increased markedly during heating. Emulsions containing hydroxylated lecithin were less sensitive to the addition of NaCl. These results suggest that the binding of hydroxylated lecithin to unfolded monomers or intermediate products of beta-lg reduces the extent of heat-induced aggregation of beta-lg and consequently decreases the interactions between unadsorbed beta-lg and adsorbed protein. This was confirmed by sodium dodecyl sulfate-polyacrylamide gel electrophoresis (SDS-PAGE) of heated whey protein and hydroxylated lecithin solutions.  相似文献   

14.
The influence of xanthan gum concentration on the physicochemical stability of model oil-in-water emulsions prepared with egg white protein at pH 3.8 and containing 150 mM NaCl was investigated by following droplet aggregate formation, rheological changes, and serum separation with storage time. Egg white emulsions were more strongly flocculated and exhibited higher stability against creaming than those of yolk, irrespective of the presence or absence of xanthan. Depletion effects, originating from the presence in the continuous phase of the emulsions of nonadsorbing xanthan molecules, intensified droplet-droplet flocculation effects and resulted in large droplet flocs. At relatively low xanthan contents, the emulsions exhibited higher stability against creaming compared to the respective control emulsions probably due to the formation of a continuous droplet aggregate network structure. At higher xanthan contents, less extensive droplet interactions, due to slowly evolving microstructure of phase-separated xanthan-rich and xanthan-depleted regions, resulted in emulsions exhibiting increased stability against creaming. The role of interactions between protein molecules adsorbed on neighboring droplets in these changes and their effect on emulsion aging are discussed.  相似文献   

15.
The potential of utilizing interfacial complexes, formed through the electrostatic interactions of proteins and polysaccharides at oil-water interfaces, to stabilize model beverage cloud emulsions has been examined. These interfacial complexes were formed by mixing charged polysaccharides with oil-in-water emulsions containing oppositely charged protein-coated oil droplets. Model beverage emulsions were prepared that consisted of 0.1 wt % corn oil droplets coated by beta-lactoglobulin (beta-Lg), beta-Lg/alginate, beta-Lg/iota-carrageenan, or beta-Lg/gum arabic interfacial layers (pH 3 or 4). Stable emulsions were formed when the polysaccharide concentration was sufficient to saturate the protein-coated droplets. The emulsions were subjected to variations in pH (from 3 to 7), ionic strength (from 0 to 250 mM NaCl), and thermal processing (from 30 or 90 degrees C), and the influence on their stability was determined. The emulsions containing alginate and carrageenan had the best stability to ionic strength and thermal processing. This study shows that the controlled formation of protein-polysaccharide complexes at droplet surfaces may be used to produce stable beverage emulsions, which may have important implications for industrial applications.  相似文献   

16.
The purpose of this study was to create water-in-oil (W/O) and water-in-oil-in-water (W/O/W) emulsions containing gelled internal water droplets. Twenty weight percent W/O emulsions stabilized by a nonionic surfactant (6.4 wt % polyglycerol polyricinoleate, PGPR) were prepared that contained either 0 or 15 wt % whey protein isolate (WPI) in the aqueous phase, with the WPI-containing emulsions being either unheated or heated (80 degrees C for 20 min) to gel the protein. Optical microscopy and sedimentation tests did not indicate any significant changes in droplet characteristics of the W/O emulsions depending on WPI content (0 or 15%), shearing (0-7 min at constant shear), thermal processing (30-90 degrees C for 30 min), or storage at room temperature (up to 3 weeks). W/O/W emulsions were produced by homogenizing the W/O emulsions with an aqueous Tween 20 solution using either a membrane homogenizer (MH) or a high-pressure valve homogenizer (HPVH). For the MH the mean oil droplet size decreased with increasing number of passes, whereas for the HPVH it decreased with increasing number of passes and increasing homogenization pressure. The HPVH produced smaller droplets than the MH, but the MH produced a narrower particle size distribution. All W/O/W emulsions had a high retention of water droplets (>95%) within the larger oil droplets after homogenization. This study shows that W/O/W emulsions containing oil droplets with gelled water droplets inside can be produced by using MH or HPVH.  相似文献   

17.
The ability of enzymatically synthesized structured phosphatidylcholine (PC) containing caprylic acid to form and stabilize oil-in-water emulsions prepared with different triglycerides [medium chain triglycerides (MCT), soybean oil, and enzymatically synthesized structured lipids] was examined and compared with natural soybean PC and deoiled lecithin. Emulsions were prepared with varying oil and emulsifier concentrations. The particle size distribution, creaming stability, and viscosity were measured for the evaluation of the emulsifying properties. With an increase in the oil concentration, there was an increase in particle size, viscosity, and creaming layer. With an increase in the phospholipid (PL) concentration, there was usually a decrease in particle size and an increase in viscosity, where the emulsion stability was increased. General emulsions prepared with structured lipids resulted in smaller particle sizes as compared to MCT and soybean oil. Deoiled lecithin was able to increase the viscosity more significantly and give smaller particle sizes as compared to the other emulsifiers, thus producing more stable emulsions. However, in certain cases, structured PC was superior to deoiled lecithin and soybean PC. This observation was made for emulsions prepared with soybean oil or structured lipid at an oil/water ratio of 10:90. At an oil/water ratio of 30:70, the deoiled lecithin performed better as compared to the other PLs with all oil types. However, structured PC produced more stable emulsions as compared to natural soybean PC in MCT and soybean oil.  相似文献   

18.
The objective of this study was to investigate the influence of globular protein interfacial cross-linking on the in vitro digestibility of emulsified lipids by pancreatic lipase. 3% (wt/wt) corn oil-in-water emulsions stabilized by either lecithin or beta-lactoglobulin were prepared (pH 7). A portion of the beta-lactoglobulin stabilized emulsions was subjected to a heat treatment known to cross-link the adsorbed globular proteins (85 degrees C, 20 min). Pancreatic lipase and bile extract were then added to each emulsion at 37 degrees C (pH 7) and the evolution of the particle charge, particle size, appearance and free fatty acids released were measured over a period of 2 h. The rate and extent of lipid digestion did not differ greatly between lecithin and beta-lactoglobulin stabilized emulsions, nor did it differ greatly for unheated (BLG-U) or heated (BLG-H) beta-lactoglobulin stabilized emulsions. For example, the initial rate of lipid digestion was found to be 3.1, 3.4, and 2.3 mM fatty acids s(-1) m(-2) of lipid surface for droplets stabilized by BLG-U, BLG-H, and lecithin, respectively. Pancreatic lipase was able to adsorb to the droplet surfaces and access the emulsified lipids, regardless of the initial interfacial composition and the fact that some of the original emulsifier appeared to remain at the oil-water interface during digestion. These results help to explain why the human body is so efficient at digesting dietary triacylglycerols.  相似文献   

19.
Chickpea and lentil protein-stabilized emulsions were optimized with regard to pH (3.0-8.0), protein concentration (1.1-4.1% w/w), and oil content (20-40%) for their ability to form and stabilize oil-in-water emulsions using response surface methodology. Specifically, creaming stability, droplet size, and droplet charge were assessed. Optimum conditions for minimal creaming (no serum separation after 24 h), small droplet size (<2 μm), and high net droplet charge (absolute value of ZP > 40 mV) were identified as 4.1% protein, 40% oil, and pH 3.0 or 8.0, regardless of the plant protein used for emulsion preparation.  相似文献   

20.
This study assessed the stabilizing effect of enzymatic cross-linking on double-coated emulsions (beet pectin-fish gelatin). The beet pectin layer was cross-linked via ferulic acid groups using laccase (an enzyme that is known to catalyze the oxidation of phenolic groups). Fish gelatin-coated oil droplets (primary emulsion) were mixed at pH 3.5 to promote electrostatic deposition of the beet pectin molecules onto the surfaces of the oil droplets (secondary emulsion). Laccase was then added to promote cross-linking of the adsorbed beet pectin layer. Cross-linked pectin-coated oil droplets had similar or significantly better stability (p < 0.05) than oil droplets of primary or secondary emulsions to NaCl addition (0-500 mM), CaCl(2) addition (0-250 mM), and thermal processing (30-90 °C for 30 min). Freeze-thaw stability and creaming behavior of enzyme-treated, secondary emulsions after two cycles (-8 °C for 22 h; 25 °C for 2 h) were significantly improved (p < 0.05). These results may have important implications for food manufacturers that are in need of emulsions with improved physical stability, for example, emulsions used in frozen foods for sauces or dips.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号