| 棉秆燃烧过程中的颗粒物排放特性 |
| |
| 引用本文： | 成 伟,陈汉平,杨海平,邵敬爱,杨 伟,朱有健,李佳硕.棉秆燃烧过程中的颗粒物排放特性[J].农业工程学报,2017,33(19):223-228. |
| |
| 作者姓名： | 成 伟 陈汉平 杨海平 邵敬爱 杨 伟 朱有健 李佳硕 |
| |
| 作者单位： | 1. 华中科技大学能源与动力工程学院,煤燃烧国家重点实验室,武汉 430074;2. 华中科技大学能源与动力工程学院,煤燃烧国家重点实验室,武汉 430074;华中科技大学能源与动力工程学院,新能源科学与工程系,武汉 430074;3. 郑州轻工业大学能源与动力工程学院,郑州,450002;4. 华中科技大学能源与动力工程学院,新能源科学与工程系,武汉 430074 |
| |
| 基金项目： | 国家自然科学基金（51476067，51506071）；湖北省自然科学基金（2016CFB132） |
| |
| 摘 要： | 该文利用滴管炉结合DEKATI低压撞击采样器,研究燃烧温度和原料粒径对棉秆燃烧过程中颗粒物排放特性的影响,并结合扫描电镜和X射线光谱分析仪探讨了颗粒物的微观结构和元素组成.结果表明PM1排放量随燃烧温度升高而显著降低,从68.90 mg/m3降低至14.02 mg/m3;颗粒物总排放量从75.41 mg/m3降低至16.30 mg/m3;颗粒物分布峰值从0.609μm附近移至0.261μm附近;原料粒径减小使得PM1排放量下降,从39.84 mg/m3降低23.06 mg/m3,而PM1-10排放量增加,从5.18 mg/m3增至8.38 mg/m3.分析表明细颗粒物(0.028~0.261μm)主要由K、Cl及少量S元素组成,形成途径主要为碱金属化合物如KCl、KOH及K2SO4等的蒸发-凝集作用,并呈现较规则的微观结构,存在形式主要为KCl;粗颗粒物(1.590~9.860μm)主要由Ca、Mg及少量Si、P组成,主要通过大颗粒的破碎或富Ca、Mg和Si颗粒物的异质凝结转化形成,多呈较规则的球形结构;中间段颗粒物(0.261~1.590μm)属于过渡段,介于细颗粒物和粗颗粒物之间,微观结构较为复杂.
|
| 关 键 词： | 秸秆 燃烧 颗粒物 粒径分布 微观结构 |
| 收稿时间： | 2017/5/21 0:00:00 |
| 修稿时间： | 2017/9/11 0:00:00 |
Emission characteristics of particulate matter during combustion of cotton stalk |
| |
| Cheng Wei,Chen Hanping,Yang Haiping,Shao Jingai,Yang Wei,Zhu Youjian and Li Jiashuo.Emission characteristics of particulate matter during combustion of cotton stalk[J].Transactions of the Chinese Society of Agricultural Engineering,2017,33(19):223-228. |
| |
| Authors: | Cheng Wei Chen Hanping Yang Haiping Shao Jingai Yang Wei Zhu Youjian and Li Jiashuo |
| |
| Institution: | 1. State Key Laboratory of Coal Combustion, School of Energy and Power Engineering, Huazhong University of Science & Technology, Wuhan 430074, China,1. State Key Laboratory of Coal Combustion, School of Energy and Power Engineering, Huazhong University of Science & Technology, Wuhan 430074, China; 2. Department of New Energy Science and Engineering, School of Energy and Power Engineering, Huazhong University of Science & Technology, Wuhan 430074, China,1. State Key Laboratory of Coal Combustion, School of Energy and Power Engineering, Huazhong University of Science & Technology, Wuhan 430074, China,1. State Key Laboratory of Coal Combustion, School of Energy and Power Engineering, Huazhong University of Science & Technology, Wuhan 430074, China; 2. Department of New Energy Science and Engineering, School of Energy and Power Engineering, Huazhong University of Science & Technology, Wuhan 430074, China,1. State Key Laboratory of Coal Combustion, School of Energy and Power Engineering, Huazhong University of Science & Technology, Wuhan 430074, China,3. School of Energy and PowerEngineering, Zhengzhou University of Light Industry, Zhengzhou 450002, China and 2. Department of New Energy Science and Engineering, School of Energy and Power Engineering, Huazhong University of Science & Technology, Wuhan 430074, China |
| |
| Abstract: | In this paper, DEKATI low pressure impactor and drop tube furnace combustion system were combined to study the emission characteristics of particulate matter during the combustion. The formation mechanism of particulate matter was investigated by scanning electron microscope (SEM) and X-ray fluorescence (XRF). Proximate and ultimate analysis of cotton stalk sample showed that the ash content and the fixed carbon content of the cotton were lower, the volatile content was higher and the overall calorific value was lower compared with coal. It was found that the yield of PM1 during the combustion experiments decreased significantly with the increase of the combustion temperature by mass distribution analysis. The combustion temperature increased from 1173 to 1473 K. The yield of PM1 decreased from 68.90 to 14.02 mg/m3. At the same time, the total yield of particulate matter also decreased from 75.41 to 16.30 mg/m3. And the peak of particle distribution moved from around 0.609 to around 0.261 μm. The smaller the particle size of the raw material, the lower the yield of PM1. The yield of PM1 decreased from 39.84 mg/m3 to 23.06 mg/m3 with the decrease of the particle size of the raw material. By contrast, the yield of PM1-10 increased from 5.18 to 8.38 mg/m3. The yield of particle under PM0.1 was very low, only 0.38 mg/m3, so the particle size of the raw material had no obvious effect on it. The mass-based particle size distributions (PSD) of particulate matter exhibited a bimodal distribution. The analysis of elements showed that the fine particle (0.028-0.261 μm) mainly consisted of K, Cl and a little amount of S. The main forming pathway of the fine particle was vaporization-condensation of the alkali compound such as KCl, KOH and K2SO4. However, heterogeneous condensation, agglomeration and coalescence contributed to PM1 formation at a certain degree during the combustion. The microstructure of the fine particle was regular and the main component was KCl. The elements of coarse particle (1.590-9.860 μm) were mainly composed of Ca, Mg and a small amount of Si and P. The main forming pathway of the coarse particle was the fracture of large particle or the transformation of Ca-rich, Mg-rich and Si-rich particles with heterogeneous condensation. In addition, the formation of silicates and phosphates influenced the formation of coarse particle. The surface shape of the coarse particle was mostly spherical. Intermediate particle (0.261-1.590 μm) belonged to the transition section and had the characteristics of both fine particle and coarse particle in complex microstructure. |
| |
| Keywords: | straw combustion particulate matter particle size distribution microstructure |
| 本文献已被 万方数据 等数据库收录！ |
| 点击此处可从《农业工程学报》浏览原始摘要信息 |
| 点击此处可从《农业工程学报》下载免费的PDF全文 |
|
